Fusion energy-production from a deuterium-tritium plasma in the jet tokamak

Describes a series of experiments in the Joint European Torus (JET), culminating in the first tokamak discharges in deuterium-tritium fuelled mixture. The experiments were undertaken within limits imposed by restrictions on vessel activation and tritium usage. The objectives were: (i) to produce more than one megawatt of fusion power in a controlled way; (ii) to validate transport codes and provide a basis for accurately predicting the performance of deuterium-tritium plasmas from measurements made in deuterium plasmas; (iii) to determine tritium retention in the torus systems and to establish the effectiveness of discharge cleaning techniques for tritium removal; (iv) to demonstrate the technology related to tritium usage; and (v) to establish safe procedures for handling tritium in compliance with the regulatory requirements. A single-null X-point magnetic configuration, diverted onto the upper carbon target, with reversed toroidal magnetic field was chosen. Deuterium plasmas were heated by high power, long duration deuterium neutral beams from fourteen sources and fuelled also by up to two neutral beam sources injecting tritium. The results from three of these high performance hot ion H-mode discharges are described: a high performance pure deuterium discharge; a deuterium-tritium discharge with a 1% mixture of tritium fed to one neutral beam source; and a deuterium-tritium discharge with 100% tritium fed to two neutral beam sources. The TRANSP code was used to check the internal consistency of the measured data and to determine the origin of the measured neutron fluxes. In the best deuterium-tritium discharge, the tritium concentration was about 11% at the time of peak performance, when the total neutron emission rate was 6.0 × 10¹⁷ neutrons/s. The integrated total neutron yield over the high power phase, which lasted about 2 s, was 7.2 × 10¹⁷ neutrons, with an accuracy of ±7%. The actual fusion amplification factor, Q_DT was about 0.15

Choice of Flexible Production Technologies Under Strategic Delegation

This work analyzes a managerial delegation model in which firms can choose between a flexible production technology which allows them to produce two different products and a dedicated production technology which limits production to only one product. We analyze whether the incentives to adopt the flexible technology are smaller or greater in a managerial delegation model than under strict profit maximization. We obtain that the asymmetric equilibrium in which only one firm adopts the flexible technology can be sustained under strategic delegation but not under strict profit maximization when products are substitutes. We extend the analysis to consider welfare implications.

Coupled deformation-flow analysis for methane hydrate production by depressurized wells

A formulation for coupled flow-deformation analysis of methane-hydrate extraction problems is presented. By assuming that the hydrate does not flow, a two phase flow formulation is considered, based on Darcy's law and capillary pressure relation. The formulation is implemented in the finite difference code FLAC. The code was used to investigate the stability of a methane extraction well by depressurizing the well. © 2005 Taylor & Francis Group, London.

Cost-Saving production technologies and strategic delegation

This work analyzes a managerial delegation model in which firms that produce a differentiated good can choose between two production technologies: a low marginal cost technology and a high marginal cost technology. For the former to be adopted more investment is needed than for the latter. By giving managers of firms an incentive scheme based on a linear combination of profit and sales revenue, we find that Bertrand competition provides a stronger incentive to adopt the cost-saving technology than the strict profit maximization case. However, the results may be reversed under Cournot competition. We show that if the degree of product substitutability is sufficiently low (high), the incentive to adopt the cost-saving technology is larger under strict profit maximization (strategic delegation).

Innovative reaction systems for acetal (1,1 diethoxy butane) production from renewable sources

370 p.: il., graf.

Overcoming hurdles to sustainable industrial fisheries production

(PDF has 25 pages.)

Breed effect on quality veal production in mountain areas: Emphasis on meat

This study was designed to compare the quality of veal produced from ‘Tudanca x Charolais’ cross (n=6) and Limousin (n=6) breeds when allowed to feed freely on mountain pastures and suckle naturally from birth to 7 months of age. After 80 days of age calves also had access to concentrate (maximum of 3 Kg/day), while mothers did not. At slaughter, Limousin calves were heavier (P<0.01) and provided better carcass yield (P<0.05) and conformation (P<0.001) than Tudanca calves. Tudanca beef provided higher fat content (P<0.05) was less tough (P<0.05), and was scored as more tender and juicy (P<0.1) with higher acceptability than Limousin beef (P<0.1). In general, Tudanca had a better fatty acid profile than Limousin beef, especially in terms of the content of polyunsaturated (P<0.05), long-chain polyunsaturated fatty acids (P<0.05) and their n-6/n-3 ratios (P<0.1), as well as vaccenic acid (P<0.1) and the overall trans-18:1 isomer profile.

Spawn production in hapas

(4 pp.)

Spawn production in hatcheries

(4 p.)