935 resultados para EDGE DISLOCATIONS
Resumo:
This report updates the Iowa Department of Transportation (DOT) design procedures for circular, slope-tapered concrete culverts. The current practice is to use the design coefficients for a square-edged, circular concrete culvert with a headwall that are found in Hydraulic Series No. 5 (HDS-5). New inlet control design constants and entrance loss coefficients were calculated for the slope-tapered culverts and then compared with the HDS-5 coefficients (square edge). In addition, various reducer lengths and taper ratios were also studied to determine what impact, if any, they have on the design coefficients. All of the laboratory testing was done at the Federal Highway Administration�s Turner-Fairbank Highway Research Center located in McLean, Virginia.
Resumo:
Foamed asphalt shoulders were placed on an Industrial Connector road at the south edge of Muscatine. The foamed asphalt was produced by injecting 1 to 2 percent water into hot asphalt cement in a patented foaming chamber. A foam develops which is 10 to 15 times the original volume. of the asphalt cement. A 3/8" limestone aggregate was used in the foamed asphalt mixture. This foamed asphalt was placed on the shoulders and in the radii on the Industrial Connector road in May 1987. The radii were later replaced due to reconstruction, but the shoulders remain and performed fairly well with some recent stripping and potholing. The performance appeared to be lower than expected from conventional hot mix on projects with similar traffic.
Resumo:
A one mile section each of thermoplastic and epoxy pavement marking materials were placed on new ACC pavement near Carroll, IA on Highway 30. The markings were evaluated for four years to see if they were suitable materials for durable pavement markings. The epoxy markings were inadvertently repainted after two years. They were performing well up to that time with little plow damage and good retroreflectivity. The thermoplastic dash lines suffered heavy snow plow damage after the first year and were repainted after the third winter. The thermoplastic edge lines performed fairly well for four years.
Resumo:
Résumé : L'arc volcanique du sud de l'Amérique Centrale se situe sur la marge SW de la Plaque Caraïbe, au-dessus des plaques subduites de Cocos et Nazca. Il s'agit de l'un des arcs intra-océaniques les plus étudiés au monde, qui est généralement considéré comme s'étant développé à la fin du Crétacé le long d'un plateau océanique (le Plateau Caraïbe ou CLIP) et se trouvant actuellement dans un régime de subduction érosive. Au cours des dernières décennies, des efforts particuliers ont été faits pour comprendre les processus liés à la subduction sur la base d'études géophysiques et géochimiques. Au sud du Costa Rica et à l'ouest du Panama, des complexes d'accrétions et structures à la base de l'arc volcanique ont été exposés grâce à la subduction de rides asismiques et de failles transformantes. Des affleurements, situés jusqu'à seulement 15 km de la fosse, offrent une possibilité unique de mieux comprendre quelques uns des processus ayant lieu le long de la zone de subduction. Nous présentons de nouvelles contraintes sur l'origine de ces affleurements en alliant une étude de terrain poussée, de nouvelles données géochimiques, sédimentaires et paléontologiques, ainsi que des observations structurales effectuées en télédétection. Une nouvelle stratigraphie tectonique entre le Campanien et l'Éocène est définie pour la région d'avant-arc située entre la Péninsule d'Osa (Costa Rica) et la Péninsule d'Azuero (Panama). Nos résultats montrent que la partie externe de la marge est composée d'un arrangement complexe de roches ignées et de séquences sédimentaires de recouvrement qui comprennent principalement le socle de l'arc, des roches d'arc primitif, des fragments de monts sous-marins accrétés et des mélanges d'accrétion. Des preuves sont données pour le développement de l'arc volcanique du sud de l'Amérique Centrale sur un plateau océanique. Le début de la subduction le long de la marge SW de la Plaque Caraïbe a eu lieu au Campanien et a généré des roches d'arc primitif caractérisées par des affinités géochimiques particulières, globalement intermédiaires entre des affinités de plateau et d'arc insulaire. L'arc était mature au Maastrichtien et formait un isthme essentiellement continu entre l'Amérique du Nord et l'Amérique du Sud. Ceci a permis la migration de faunes terrestres entre les Amériques et pourrait avoir contribué à la crise fin Crétacé -Tertiaire en réduisant les courants océaniques subéquatoriaux entre le Pacifique et l'Atlantique. Plusieurs unités composées de fragments de monts sous-marins accrétés sont définies. La nature et l'arrangement structural de ces unités définissent de nouvelles contraintes sur les modes d'accrétion des monts sous-marins/îles océaniques et sur l'évolution de la marge depuis la formation de la zone de subduction. Entre la fin du Crétacé et l'Éocène moyen, la marge a enregistré plusieurs épisodes ponctuels d'accrétion de monts sous-marins alternant avec de la subduction érosive. A l'Éocène moyen, un événement tectonique régional pourrait avoir causé un fort couplage entre les plaques supérieure et inférieure, menant à des taux plus important d'accrétion de monts sous-marins. Durant cette période, la situation le long de la marge était très semblable à la situation actuelle et caractérisée par la présence de monts sous-marins subductants et l'absence d'accrétion de sédiments. L'enregistrement géologique montre qu'il n'est pas possible d'attribuer une nature érosive ou accrétionnaire à la marge dans le passé ou -par analogie- aujourd'hui, parce que (1) les processus d'accrétion et érosifs varient fortement spatialement et temporellement et (2) il est impossible d'évaluer la quantité exacte de matériel tectoniquement enlevé à la marge depuis le début de la subduction. Au sud du Costa Rica, certains fragments de monts sous-marins accrétés sont représentatifs d'une interaction entre une ride et un point chaud dans le Pacifique au Crétacé terminal/Paléocène. L'existence de ces fragments de monts sous-marins et la morphologie du fond de l'Océan Pacifique indiquent que la formation de la ride de Cocos-Nazca s'est formée au moins ~40 Ma avant l'âge proposé par les modèles tectoniques actuels. Au Panama, nous avons identifié une île océanique d'âge début Éocène qui a été accrétée à l'Éocène moyen. L'accrétion a eu lieu à très faible profondeur par détachement de l'île dans la fosse, et a mené à une exceptionnelle préservation des structures volcaniques. Des affleurement comprenant aussi bien des parties basses et hautes de l'édifice volcanique on été étudiées, depuis la phase sous-marine bouclier jusqu'à la phase subaérienne post-bouclier. La stratigraphie nous a permis de différencier les laves de la phase sous-marine de celles de la phase subaérienne. La composition des laves indique une diminution progressive de l'intensité de la fusion partielle de la source et une diminution de la température des laves produites durant les derniers stades de l'activité volcanique. Nous interprétons ces changements comme étant liés à l'éloignement progressif de l'île océanique de la zone de fusion ou point chaud. Abstract The southern Central American volcanic front lies on the SW edge of the Caribbean Plate, inboard of the subducting Cocos and Nazca Plates. It is one of the most studied intra-oceanic convergent margins around the world, which is generally interpreted to have developed in the late Cretaceous along an oceanic plateau (the Caribbean Large Igneous Province or CLIP) and to be currently undergoing a regime of subduction erosion. In the last decades a particular effort has been made to understand subduction-related processes on the basis of geophysical and geochemical studies. In southern Costa Rica and western Panama accretionary complexes and structures at the base of the volcanic front have been exposed in response to subduction of aseismic ridges and transforms. Onland exposures are located as close as to 15 km from the trench and provide a unique opportunity to better understand some of the processes occurring along the subduction zone. We provide new constraints on the origins of these exposures by integrating a comprehensive field work, new geochemical, sedimentary and paleontological data, as well as structural observations based on remote imaging. A new Campanian to Eocene tectonostratigraphy is defined for the forearc area located between the Osa Peninsula (Costa Rica) and the Azuero Peninsula (Panama). Our results show that the outer margin is composed of a complicated arrangement of igneous complexes and overlapping sedimentary sequences that essentially comprise an arc basement, primitive island-arc rocks, accreted seamount fragments and accretionary mélanges. Evidences are provided for the development of the southern Central American arc on the top an oceanic plateau. The subduction initiation along the SW edge of the Caribbean Plate occurred in the Campanian and led to formation of primitive island-arc rocks characterized by unusual geochemical affinities broadly intermediate between plateau and arc affinities. The arc was mature in the Maastrichtian and was forming a predominantly continuous landbridge between the North and South Americas. This allowed migration of terrestrial fauna between the Americas and may have contributed to the Cretaceous-Tertiary crisis by limiting trans-equatorial oceanic currents between the Pacific and the Atlantic. Several units composed of accreted seamount fragments are defined. The nature of the units and their structural arrangement provide new constraints on the modes of accretion of seamounts/oceanic islands and on the evolution of the margin since subduction initiation. Between the late Cretaceous and the middle Eocene, the margin recorded several local episodes of seamount accretion alternating with tectonic erosion. In the middle Eocene a regional tectonic event may have triggered strong coupling between the overriding and subducting plates, leading to higher rates of seamount accretion. During this period the situation along the margin was very similar to the present and characterized by subducting seamounts and absence of sediment accretion. The geological record shows that it is not possible to ascribe an overall erosive or accretionary nature to the margin in the past and, by analogy, today, because (1) accretionary and erosive processes exhibit significant lateral and temporal variations and (2) it is impossible to estimate the exact amount of material tectonically eroded from the margin since subduction initiation. In southern Costa Rica, accreted seamount fragments point toward a plume-ridge interaction in the Pacific in the late Cretaceous/Paleocene. This occurrence of accreted seamount fragments and morphology of the Pacific Ocean floor is indicative of the formation of the Cocos-Nazca spreading system at least ~40 Ma prior to the age proposed in current tectonic models. In Panama, we identified a remarkably-well preserved early Eocene oceanic island that accreted in the middle Eocene. The accretion probably occurred at very shallow depth by detachment of the island in the trench and led to an exceptional preservation of the volcanic structures. Exposures of both deep and superficial parts of the volcanic edifice have been studied, from the submarine-shield to subaerial-postshield stages. The stratigraphy allowed us to distinguish lavas produced during the submarine and subaerial stages. The lava compositions likely define a progressive diminution of source melting and a decrease in the temperature of erupted melts in the latest stages of volcanic activity. We interpret these changes to primarily reflect the progressive migration of the oceanic island out of the melting region or hotspot.
Resumo:
The routine maintenance along Iowa's highways and roadways during the summer growing season is a time consuming and costly endeavor. Trimming around guardrail posts and delineator posts is especially costly due to the handwork required. Trimming costs account for approximately 50% of the shoulder mowing costs according to expense figures obtained from the Iowa Department of Transportation (DOT), Office of Maintenance. The FY 2001 statewide trimming costs for the Iowa DOT was approximately $430,000 ($305,000 labor, $125,000 equipment and materials). This product would be required to perform well for 9-21 years, on average, in order to recoup the cost of installation. This includes the durability of the product, but not the cost of repair due to traffic damage, snowplow and wing damage, or damage caused by mowing operations. Maintenance costs associated with vegetation creep over the mats and repair costs would extend the required service life. As a result of resource realignment, the Iowa DOT roadside maintenance policy, for FY 2003 and the future, will be to eliminate trimming around delineator posts unless the reflector is obstructed. This policy change will effectively eliminate the need for weed control mats due to the significant reduction in trimming. The use of the weed control mats could be justified in areas that are dangerous to maintenance workers such as guardrail installations in high traffic areas. Because the delineator posts are further from the edge of the traveled roadway, there is a reduced risk to the maintenance workforce while hand trimming. Because the DuroTrim Vegetation Control Mats appear to have performed adequately in the field trial, they could be considered for use, where safety conditions warrant. That use should be limited, however, due to the considerable initial cost and changes in Iowa DOT roadside maintenance policy. Application should be limited to instances where the use of the DuroTrim Vegetation Control Mats would have a significant impact on the safety of the roadside maintenance workers. The cost savings, due to the elimination of the trimming and mowing alone, is not enough to justify their use in most situations at their current cost. The test sections will continue to be monitored periodically so that approximate service life can be determined.
Resumo:
As truck traffic on Iowa secondary roads has increased, engineers have moved to concrete pavements of greater depths. Early designs included thickened edge pavements and depths of seven inches or greater. The designs typically did not have load transfer devices installed in the transverse joints and relied on aggregate interlock for this purpose. In some cases, aggregate interlock was not adequate to deal with the soils and traffic conditions and faulting of the joints has begun to appear. Engineers are now faced with the need to install or retrofit load transfer in the joints to preserve the pavements. Questions associated with this decision range from the type of dowel material to dowel diameter, spacing, number of bars, placement method, and construction techniques to be used to assure reduction or elimination of faulting. Buena Vista County constructed a dowel bar retrofit project on one mile of road. The plan called for addition of the dowels (2, 3, or 4) in the outer wheel path only and surface grinding in lieu of asphalt overlay. The project included the application of elliptical- and round-shaped dowels in a rehabilitation project. Dowel material types included conventional epoxy-coated steel and fiber-reinforced polymer (FRP). This work involved the determination of relative costs in materials to be used in this type of work and performance of FRP and elliptical-shaped steel dowels in the retrofit work. The results indicate good performance from each of the bar configurations and use the results of ride and deflection testing over the research period to project the benefits that can be gained from each configuration vs. the anticipated construction costs. The reader is cautioned that this project could not relate the number of dowels required to the level of anticipated truck traffic for other roads that might be considered.
Resumo:
The federal government is aggressively promoting biofuels as an answer to global climate change and dependence on imported sources of energy. Iowa has quickly become a leader in the bioeconomy and wind energy production, but meeting the United States Department of Energy’s goal having 20% of U.S. transportation fuels come from biologically based sources by 2030 will require a dramatic increase in ethanol and biodiesel production and distribution. At the same time, much of Iowa’s rural transportation infrastructure is near or beyond its original design life. As Iowa’s rural roadway structures, pavements, and unpaved roadways become structurally deficient or functionally obsolete, public sector maintenance and rehabilitation costs rapidly increase. More importantly, costs to move all farm products will rapidly increase if infrastructure components are allowed to fail; longer hauls, slower turnaround times, and smaller loads result. When these results occur on a large scale, Iowa will start to lose its economic competitive edge in the rapidly developing bioeconomy. The primary objective of this study was to document the current physical and fiscal impacts of Iowa’s existing biofuels and wind power industries. A four-county cluster in north-central Iowa and a two-county cluster in southeast Iowa were identified through a local agency survey as having a large number of diverse facilities and were selected for the traffic and physical impact analysis. The research team investigated the large truck traffic patterns on Iowa’s secondary and local roads from 2002 to 2008 and associated those with the pavement condition and county maintenance expenditures. The impacts were quantified to the extent possible and visualized using geographic information system (GIS) tools. In addition, a traffic and fiscal assessment tool was developed to understand the impact of the development of the biofuels on Iowa’s secondary road system. Recommended changes in public policies relating to the local government and to the administration of those policies included standardizing the reporting and format of all county expenditures, conducting regular pavement evaluations on a county’s system, cooperating and communicating with cities (adjacent to a plant site), considering utilization of tax increment financing (TIF) districts as a short-term tool to produce revenues, and considering alternative ways to tax the industry.
Resumo:
In this work, zinc indium tin oxide layers with different compositions are used as the active layer of thin film transistors. This multicomponent transparent conductive oxide is gaining great interest due to its reduced content of the scarce indium element. Experimental data indicate that the incorporation of zinc promotes the creation of oxygen vacancies. In thin-film transistors this effect leads to a higher threshold voltage values. The field-effect mobility is also strongly degraded, probably due to coulomb scattering by ionized defects. A post deposition annealing in air reduces the density of oxygen vacancies and improves the fieldeffect mobility by orders of magnitude. Finally, the electrical characteristics of the fabricated thin-film transistors have been analyzed to estimate the density of states in the gap of the active layers. These measurements reveal a clear peak located at 0.3 eV from the conduction band edge that could be attributed to oxygen vacancies.
Resumo:
Cell motility is an essential process that depends on a coherent, cross-linked actin cytoskeleton that physically coordinates the actions of numerous structural and signaling molecules. The actin cross-linking protein, filamin (Fln), has been implicated in the support of three-dimensional cortical actin networks capable of both maintaining cellular integrity and withstanding large forces. Although numerous studies have examined cells lacking one of the multiple Fln isoforms, compensatory mechanisms can mask novel phenotypes only observable by further Fln depletion. Indeed, shRNA-mediated knockdown of FlnA in FlnB¿/¿ mouse embryonic fibroblasts (MEFs) causes a novel endoplasmic spreading deficiency as detected by endoplasmic reticulum markers. Microtubule (MT) extension rates are also decreased but not by peripheral actin flow, because this is also decreased in the Fln-depleted system. Additionally, Fln-depleted MEFs exhibit decreased adhesion stability that appears in increased ruffling of the cell edge, reduced adhesion size, transient traction forces, and decreased stress fibers. FlnA¿/¿ MEFs, but not FlnB¿/¿ MEFs, also show a moderate defect in endoplasm spreading, characterized by initial extension followed by abrupt retractions and stress fiber fracture. FlnA localizes to actin linkages surrounding the endoplasm, adhesions, and stress fibers. Thus we suggest that Flns have a major role in the maintenance of actin-based mechanical linkages that enable endoplasmic spreading and MT extension as well as sustained traction forces and mature focal adhesions.
Resumo:
OBJECTIVE: Our aim was to evaluate a fluorescence-based enhanced-reality system to assess intestinal viability in a laparoscopic mesenteric ischemia model. MATERIALS AND METHODS: A small bowel loop was exposed, and 3 to 4 mesenteric vessels were clipped in 6 pigs. Indocyanine green (ICG) was administered intravenously 15 minutes later. The bowel was illuminated with an incoherent light source laparoscope (D-light-P, KarlStorz). The ICG fluorescence signal was analyzed with Ad Hoc imaging software (VR-RENDER), which provides a digital perfusion cartography that was superimposed to the intraoperative laparoscopic image [augmented reality (AR) synthesis]. Five regions of interest (ROIs) were marked under AR guidance (1, 2a-2b, 3a-3b corresponding to the ischemic, marginal, and vascularized zones, respectively). One hour later, capillary blood samples were obtained by puncturing the bowel serosa at the identified ROIs and lactates were measured using the EDGE analyzer. A surgical biopsy of each intestinal ROI was sent for mitochondrial respiratory rate assessment and for metabolites quantification. RESULTS: Mean capillary lactate levels were 3.98 (SD = 1.91) versus 1.05 (SD = 0.46) versus 0.74 (SD = 0.34) mmol/L at ROI 1 versus 2a-2b (P = 0.0001) versus 3a-3b (P = 0.0001), respectively. Mean maximal mitochondrial respiratory rate was 104.4 (±21.58) pmolO2/second/mg at the ROI 1 versus 191.1 ± 14.48 (2b, P = 0.03) versus 180.4 ± 16.71 (3a, P = 0.02) versus 199.2 ± 25.21 (3b, P = 0.02). Alanine, choline, ethanolamine, glucose, lactate, myoinositol, phosphocholine, sylloinositol, and valine showed statistically significant different concentrations between ischemic and nonischemic segments. CONCLUSIONS: Fluorescence-based AR may effectively detect the boundary between the ischemic and the vascularized zones in this experimental model.
Resumo:
In the region of Alt Empordà (Girona), olive groves historically shaped a landscape of high economic value, cultural and environmental although since mid-twentieth century is in sharp decline. One of the municipalities located on the edge of the plana altoampurdanesa that best exemplify this process of abandonment and near disappearance of that crop is Navata. This article analyzes the changes in the olive grove of this municipality in the period 1957-2004, both through the development of mapping land use and land cover level of detail as the analysis of data sources and oral exercise that makes emphasizes the loss of 90% of the existing olive grove in the middle of last century. The frost of February of 1956 was one of the main causes, but not unique. However, both the importance of the olive groves as an identity and conservation of biodiversity as the differential nature of the oil obtained from varieties natives to the area (especially argudell), justify the need to promote policies that will help your recovery
Resumo:
The recent production of synthetic magnetic fields acting on electroneutral particles, such as atoms or photons, has boosted interest in the quantum Hall physics of bosons. Adding pseudospin 1/2 to the bosons greatly enriches the scenario, as it allows them to form an interacting integer quantum Hall (IQH) phase with no fermionic counterpart. Here we show that, for a small two-component Bose gas on a disk, the complete strongly correlated regime, extending from the integer phase at filling factor ν = 2 to the Halperin phase at filling factor ν = 2 / 3, is well described by composite fermionization of the bosons. Moreover we study the edge excitations of the IQH state, which, in agreement with expectations from topological field theory, are found to consist of forward-moving charge excitations and backward-moving spin excitations. Finally, we demonstrate how pair-correlation functions allow one to experimentally distinguish the IQH state from competing states, such as non-Abelian spin singlet (NASS) states.
Resumo:
We investigate the influence of knotting and chirality on the shape of knotted polygons forming trefoil knots compared to unknotted polygons by aligning independent configurations along their principal inertial axes. While for six edge polygons forming trefoil knots the chiral knotted structure is revealed in the isodensity profiles, the distinct chiral signature of the trefoil is significantly diminished with 24 edges. We observe that as the number of edges in the polygons increases, the cumulative shapes of trefoil knots progressively approach the cumulative shapes for unknotted polygons.
Resumo:
The objective of this work was to assess the effects of a forest-field ecotone on earthworm assemblages. Five sites (blocks) differing in the type of crop rotation used in the field were studied in Central Bohemia, Czech Republic. In each block, sampling was carried out in seven parallel rows perpendicular to a transect from a forest (oak or oak-pine) to the centre of a field, both in spring and autumn 2001-2003. Individual rows were located in the forest (5 m from the edge), in the forest edge, and in the field (at 5, 10, 25, 50 and 100 m distances from the forest edge). The density and biomass of earthworms were lowest in the forest, increased markedly in the forest edge, decreased again at 5 or 10 m distance from the forest edge and then continuously increased along the distance to the field boundary. The highest number of species was found in the forest edge and in the field boundary. Individual species differed in their distribution along the transect. Both density and biomass of earthworms were correlated with distance from forest edge, soil organic matter content, soil porosity, and water infiltration rate.
Resumo:
Abstract The Northwestern edge of the modern Caribbean Plate, located in central Middle America (S-Guatemala to N-Costa Rica), is characterized by a puzzle of oceanic and continental terranes that belonged originally to the Pacific façade of North America. South of the Motagua Fault Zone, the actual northern strike slip boundary of the Caribbean Plate, three continental slivers (Copán, Chortis s. str. and Patuca) are sandwiched between two complex suture zones that contain HP/LT mafic and ultramafic oceanic rocks: The Motagua Mélanges to the North, extensively studied in the last ten years and the' newly defined Mesquito Composite Oceanic Terrane (MCOT) to the South. No modem geological data were available for the oceanic terrane located in the southern part of the so called continental "Chortis Block". Classically, the southern limit of this block with the Caribbean Large Igneous Province (CLIP) was placed at a hypothetical fault line connecting the main E-W fault in the Santa Elena Peninsula (N-Costa Rica) with the Hess Escarpment. However, our study in eastern Nicaragua and northwestern Costa Rica evidences an extensive assemblage of oceanic upper mantle and crustal rocks outcropping between the Chortis/Patuca continental blocks and the CLIP. They comprise collided and accreted exotic terranes of Pacific origin recording a polyphased tectonic history. We distinguish: 1- The MCOT that comprises a Late Triassic to Early Cretaceous puzzle of oceanic crust and arc-derived rocks set in a serpentinite matrix, and 2- The Manzanillo and Nicoya Terranes that are made of Cretaceous plateau-like rocks associated with oceanic sediments older than the CLIP. This study has been focused on the rocks of the MCOT. The MCOT comprises the southern half of the former "Chortis Block" and is defined by 4 comer localities characterized by ultramafic and mafic oceanic rocks of Late Triassic, Jurassic and Early Cretaceous age: 1- The Siuna Serpentinite Mélange (NE-Nicaragua), 2- The El Castillo Mélange (Nicaragua/Costa Rica border), 3- DSDP Legs 67 and 84 (Guatemala fore-arc basin), and 4- The Santa Elena Peridiotite (NW-Costa Rica). The Siuna Serpentinite Mélange (SSM) is a HP/LT subduction zone mélange set in a serpentinite matrix that contains oceanic crust and arc-related greenschist to blueschist/eclogite facies metamafic and metasedimentary blocks. Middle Jurassic (Bajocian-Bathonian) radiolarites are found in original sedimentary contact with arc-derived greenstones. Late Jurassic black detrital chert possibly formed in a marginal (fore-arc?) basin shortly before subduction. A phengite 40Ar/39Ar -cooling age dates the exhumation of the high pressure rocks as 139 Ma. The El Castillo Mélange (ECM) is composed of serpentinite matrix with OIB metabasalts and Late Triassic (Rhaetian) red and green radiolarite blocks. Recent studies of the DSDP Legs 67/84 show that the Guatemala/Nicaragua fore-arc basin is composed of a pile of ultramafic, mafic (OIB-like) and arc related rocks with ages ranging from Late Triassic to Campanian. Finally, the Santa Elena peridiotites that mark the limit of the MCOT with the Manzanillo/Nicoya Terranes and correspond to an association of ultramafic rocks that comprise peridiotites, dunites and chromites of abyssal and fore-arc origin. The SSM is the result of a collision between a Middle Jurassic island arc and the Patuca Terrane, a fragment of the Western N-American active continental margin. The Siuna Mélange (SSM) and the South Montagna Mélange share common characteristics with the Pacific N-American suture zone (E-Franciscan and Vizcaino mélanges), in particular, the Mesozoic ages of HP/LT metamorphic and the arc-derived blocks. For us, these mélanges imply an originally continuous, but slightly diachronous suture that affected the entire W-American active margin. It may imply the arrival and collision of an exotic intraoceanic arc (Guerrero-Phoenix) related to the origin of the Pacific Plate that initiated as a back arc basin of this arc. The present disposition of the fragments of this suture zone is the result of a northward shift of the active left-lateral strike slip motion between the N-American and the Caribbean Plates. Résumé Le coin nord-ouest de la Plaque Caraïbe moderne se trouve en Amérique Centrale, entre le sud du Guatemala et le nord du Costa Rica. Cette région est composée d'un puzzle de terrains océaniques et continentaux dont les origines se situent sur la façade pacifique de l'Amérique du Nord. Au sud de la faille de Motagua, la limite septentrionale actuelle, décrochante, de la Plaque Caraïbe, se trouvent 3 copeaux continentaux (Copàn, Chortis s. str. et Patuca) coincés entre deux zones de suture complexes à roches mafiques et ultramafiques qui ont subi un métamorphisme de haute pression/basse température (HP/LT). Il s'agit des Mélanges de Motagua au nord, largement étudiés ces dernières années, et du Mesquito Composite Oceanic Terrane (MCOT), récemment défini par nous, au sud. En vue de l'absence de données géologiques modernes concernant les terrains océaniques qui se trouvent dans la partie sud du "Chortis Block" considérée comme continentale, nous avons dédié cette étude à cette région. Classiquement, la limite méridionale entre le "Chortis Block" et la "Caribbean Large Igneous Province" (CLIP) a été associée à une faille hypothétique reliant la faille E-W de Santa Elena (nord du Costa Rica) à l'Escarpement de Hess. Notre étude au Nicaragua oriental et au Costa Rica nord-occidental a révélé l'existence de larges terrains composés d'assemblages de roches mantéliques et océaniques qui se placent entre les blocs continentaux Chortis/Patuca et le CLIP. Ces assemblages révèlent des terrains collisionnés et accrétés d'origine pacifique enregistrant une histoire tectonique polyphasée. Nous distinguons: 1- Le MCOT, un puzzle de roches océaniques d'arc d'âge Triassique supérieur au Crétacée inférieur, 2- Les terrains de Manzanillo et de Nicoya, des morceaux de plateaux océaniques associés à des sédiments océaniques plus âgés que le CLIP. Cette étude se focalisera sur les roches du MCOT. Le MCOT occupe la moitié sud de l'ancien "Chortis Block" et peut se définir par 4 localités de référence qui montrent des roches mafiques et ultramafiques océaniques d'âges compris entre le Trias supérieur et le Crétacée inférieur. 1- Le Siuna Serpentinite Mélange (NE-Nicaragua), 2- Le El Castillo Mélange (Nicaragua/Costa Rica border), 3- Le DSDP Legs 67/84 (Guatemala fore-arc basin) et 4- La Santa Elena Peridiotite (nord-ouest du Costa Rica). Le Siuna Serpentinite Mélange (SSM) est un mélange de subduction HP/BT dans une matrice de serpentinite. On y trouve des éléments de croûte océanique et d'arc insulaire en faciès de schistes verts et schistes bleus. Des radiolarites du Jurassique moyen se trouvent en contact sédimentaire sur des roches vertes d'arc. En revanche, des cherts noirs détritiques datent du Jurassique supérieur et sont probablement issus d'un bassin marginal (fore-arc ?) peu avant leur subduction, car un âge 40Ar/39Ar de refroidissement des phengites date l'exhumation des roches de haute pression à 139 Ma. Le Mélange d'El Castillo (ECM) est constitué d'une matrice serpentinitique et contient des blocs de metabasaltes OIB et des blocs de radiolarites du Trias terminal. Des études récentes ont repris les roches forées lors des DSDP Legs 67 et 84 et montrent que le soubassement du bassin d'avant-arc du Guatemala-Nicaragua est composé de roches ultramafiques et mafiques (OIB et arc), dont les âges isotopiques vont du Trias au Crétacé supérieur. Finalement, les péridiotites de Santa Elena forment la limite sud du MCOT par rapport aux terrains de Manzanillo et Nicoya. Elles contiennent des serpentinites et localement des dunites et chromites à affinité abyssale et de fore-arc. Le SSM témoigne d'une collision entre un arc insulaire d'âge Jurassique moyen et le Patuca Terrane, un fragment de la marge active nord-américaine. Le SSM et le South Motagua Mélange ont des caractéristiques en commun avec les zones de suture de la façade pacifique de l'Amérique du nord (E-Franciscan et Vizcaino mélanges), notamment les âges Mésozoïques du métamorphisme HP/BT et les blocs de roches d'arc. Ce fait nous conduit à penser qu'il s'agit d'une grande zone de suture qui était à l'origine continue sur toute la marge ouest-américaine, mais légèrement diachrone. Cette suture implique l'arrivée et la collision d'un arc intraocéanique exotique (Guerrero-Phoenix) qui est à l'origine de la Plaque Pacifique qui s'ouvrait en back arc par rapport à celui-ci. La disposition actuelle des fragments de cette suture est due à la migration vers le nord du décrochement actif senestre entre la Plaque nord-américaine et la Plaque Caraïbe. K. Flores, 2009 Mesozoic oceanic terranes of southern central America Résumé Grand Public La présente thèse est le résultat de travaux de terrain effectués de 2005 à 2008 au nord-est et au sud du Nicaragua et au nord du Costa Rica, en Amérique Centrale, des analyses pétrologiques et géochimiques en laboratoire ainsi que de la modélisation de l'évolution géodynamique. La région étudiée se situe en bordure nord - ouest de la Plaque Caraïbe moderne. Dans la majorité des publications récentes cette région est représentée comme un vaste bloc continental (le "Bloc Chortis") qui serait limité, (i) au nord, par la faille décrochante de Motagua, la limite actuelle entre la Plaque Nord-Américaine et la Plaque Caraïbe, et (ii) au sud, par une suture hypothétique qui se trouverait aux confins entre le Nicaragua et le Costa Rica. La région du Costa Rica a été considérée presque entièrement comme une partie du Plateau Caraïbe ("Caribbean Large Igneous Province" (CLIP)). L'étude détaillée des affleurements nous a permis de mettre en évidence : - Au nord-est du Nicaragua (Siuna) : Des roches océaniques datées du Jurassique moyen, grâce aux faunes à radiolaires qui ont été extraites des radiolarites rouges. Ces roches ont subi un métamorphisme de haute pression typique des zones de collision. L'étude radio-isotopique Ar/Ar a permis de dater la collision du Crétacé basal (139 Ma). - Au sud du Nicaragua : Des roches océaniques d'âge Trias terminal (200 millions d'années), également datées à l'aide de faunes à radiolaires. Il s'agit actuellement des roches océaniques les plus anciennes connues de l'Amérique Centrale. - L'étude géochimique et les âges des fossiles démontrent que le tiers septentrional du Costa Rica possède un soubassement construit d'au moins deux terrains (Nicoya et Manzanillo), qui ont des caractéristiques de Plateau océanique (Nicoya) et d'arc volcanique du Crétacé moyen (Manzanillo). Ces deux terrains sont plus anciens que le CLIP. En conclusion, nous constatons que la région étudiée est constituée d'un puzzle de 3 blocs continentaux et d'un vaste terrain océanique composite que nous appelons Mesquito Composite Oceanic Terrane (MCOT). En plus, nous définissons les terrains de Nicoya et de Manzanillo comme plus âgés et distincts du CLIP. Le MCOT est caractérisé par la présence de roches du manteau supérieur (les serpentinites) et de la croûte océanique, ainsi que des morceaux d'arcs, d'âge allant du Trias supérieur au Crétacé. Ce terrain est comparable à d'autres zones de suture de la façade pacifique de l'Amérique du nord, notamment en ce qui concerne les âges Mésozoïques, le métamorphisme de haute pression et l'association de roches mantéliques et crustales océaniques. Ce fait nous conduit à penser qu'il s'agit d'une grande zone de suture qui était à l'origine continue sur toute la marge ouest-américaine. Cette suture implique l'arrivée et la collision d'un arc infra-océanique exotique qui serait à l'origine de la Plaque Pacifique qui se serait ouverte en bassin d'arrière arc par rapport à celui-ci. La disposition actuelle des fragments de cette suture est due à la migration vers le nord du décrochement actif senestre entre la Plaque nord-américaine et la Plaque Caraïbe.