An assessment of the relative influence of a vapor recovery system in reducing occupational exposure to volatile organic compounds in high performance liquid chromatography

Occupational exposures to organic solvents, specifically acetonitrile and methanol, have the potential to cause serious long-term health effects. In the laboratory, these solvents are used extensively in protocols involving the use of high performance liquid chromatography (HPLC). Operators of HPLC equipment may be potentially exposed to these organic solvents when local exhaust ventilation is not employed properly or is not available, which can be the case in many settings. The objective of this research was to characterize the various sites of vapor release in the HPLC process and then to determine the relative influence of a novel vapor recovery system on the overall exposure to laboratory personnel. The effectiveness of steps to reduce environmental solvent vapor concentrations was assessed by measuring exposure levels of acetonitrile and methanol before and after installation of the vapor recovery system. With respect to acetonitrile, the concentration was not statistically significant with p=0.938; moreover, exposure after the intervention was actually higher than prior to intervention. With respect to methanol, the concentration was not statistically significant with p=0.278. This indicates that the exposure to methanol after the intervention was not statistically significantly higher or lower than prior to intervention. Thus, installation of the vapor recovery device did not result in statistically significant reduction in exposures in the settings encountered, and acetonitrile actually increased significantly.^

Mid-Wisconsin to Holocene permafrost and landscape dynamics based on a drained lake basin core from the northern Seward Peninsula, Northwest Alaska

Permafrost-related processes drive regional landscape dynamics in the Arctic terrestrial system. A better understanding of past periods indicative of permafrost degradation and aggradation is important for predicting the future response of Arctic landscapes to climate change. Here, we used a multi-proxy approach to analyze a ~4 m long sediment core from a drained thermokarst lake basin on the northern Seward Peninsula in western Arctic Alaska (USA). Sedimentological, biogeochemistical, geochronological, micropaleontological (ostracoda, testate amoeba) and tephra analyses were used to determine the long-term environmental Early-Wisconsin to Holocene history preserved in our core for Central Beringia. Yedoma accumulation dominated throughout the Early to Late-Wisconsin but was interrupted by wetland formation from 44.5 to 41.5 ka BP. The latter was terminated by deposition of 1 m of volcanic tephra, most likely originating from the South Killeak Maar eruption at about 42 ka BP. Yedoma deposition continued until 22.5 ka BP and was followed by a depositional hiatus in the sediment core between 22.5 and 0.23 ka BP. We interpret this hiatus as due to intense thermokarst activity in the areas surrounding the site, which served as a sediment source during the Late-Wisconsin to Holocene climate transition. The lake forming the modern basin on the upland initiated around 0.23 ka BP, which drained catastrophically in spring 2005. The present study emphasizes that Arctic lake systems and periglacial landscapes are highly dynamic and permafrost formation as well as degradation in Central Beringia was controlled by regional to global climate patterns and as well as by local disturbances.

Eocene to Early Miocene palaeoclimate of Saxony, Germany (Table 4)

In the present study, proxy data concerning changes in atmospheric CO2 and climatic conditions from the Late Eocene to the Early Miocene were acquired by applying palaeobotanical methods. Fossil floras from 10 well-documented locations in Saxony, Germany, were investigated with respect to (1) stomatal density/index of fossil leaves from three different taxa (Eotrigonobalanus furcinervis, Laurophyllum pseudoprinceps and Laurophyllum acutimontanum), (2) the coexistence approach (CA) based on nearest living relatives (NLR) and (3) leaf margin analysis (LMA). Whereas the results of approach (1) indicate changes in atmospheric CO2 concentration, approaches (2) and (3) provide climate data. The results of the analysis of stomatal parameters indicate that the atmospheric CO2 concentration was higher during the Late Eocene than during the Early Oligocene and increased towards the Late Oligocene. A lower atmospheric pCO2 level after the Late Eocene is also suggested by an increase in marine palaeoproductivity at this time. From the Late Oligocene onwards, no changes in atmospheric CO2 concentration can be detected with the present data. For the considered sites, the results of the coexistence approach and of the leaf margin analysis document a significant cooling event from the Late Eocene to the Early Oligocene. The pCO2 decrease from the Late Eocene to the Early Oligocene indicated by the stomatal data raised in this study was thus coupled to a temperature decrease which is reflected by the present datasets. From the Early Oligocene onwards, however, no further fundamental climate change can be inferred for the considered locations. The pCO2 increase from the Early Oligocene to the Late Oligocene, which is indicated by the present data, is thus not accompanied by a climate change at the considered sites. A warming event during the Late Oligocene is, however, recorded by marine climate archives. According to the present data, no change in pCO2 occurred during the cooling event at the Oligocene/Miocene boundary, which is also indicated by marine data. The quality and validity of stomatal parameters as sensors for atmospheric CO2 concentration are discussed.

Late Miocene to Early Pliocene radiolarians from ODP Hole 178-1095B

Early Pliocene to middle late Miocene hemipelagic and distal turbidite sediments from Hole 1095B, near the Antarctic Peninsula, yield moderately abundant, moderately well preserved radiolarian faunas and other biosiliceous material (diatoms, silicoflagellates, and sponge spicules). Preservation characteristics, however, vary strongly even between closely related samples, and there are many intervals of poor preservation. In the 140- to 460-meters below seafloor interval studied, it was possible to identify the following standard Southern Ocean radiolarian zones: Upsilon, Tau, Amphymenium challengerae, Acrosphaera? labrata, Siphonosphaera vesuvius, and upper Acrosphaera australis (total age range ~4-10 Ma). Some normally common radiolarian groups, such as actinommids, are unusually rare in the studied material, and the relative ranges of several individual species, such as Acrosphaera labrata vs. A. australis, appear to be somewhat anomalous. These observations imply that the ranges of taxa in this section may be somewhat diachronous, due to either local ecologic factors and/or the highly variable preservation of the faunas. Thus, the ages of events reported are probably only approximate, although they are still useful for constraining the age of sediments in this section.

Unsupervised system to classify SO2 pollutant concentrations in Salamanca, Mexico

Salamanca is cataloged as one of the most polluted cities in Mexico. In order to observe the behavior and clarify the influence of wind parameters on the Sulphur Dioxide (SO2) concentrations a Self-Organizing Maps (SOM) Neural Network have been implemented at three monitoring locations for the period from January 1 to December 31, 2006. The maximum and minimum daily values of SO2 concentrations measured during the year of 2006 were correlated with the wind parameters of the same period. The main advantages of the SOM Neural Network is that it allows to integrate data from different sensors and provide readily interpretation results. Especially, it is powerful mapping and classification tool, which others information in an easier way and facilitates the task of establishing an order of priority between the distinguished groups of concentrations depending on their need for further research or remediation actions in subsequent management steps. For each monitoring location, SOM classifications were evaluated with respect to pollution levels established by Health Authorities. The classification system can help to establish a better air quality monitoring methodology that is essential for assessing the effectiveness of imposed pollution controls, strategies, and facilitate the pollutants reduction.

System supporting public transport based on geolocation

El propósito de este proyecto de fin de Grado es el estudio y desarrollo de una aplicación basada en Android que proporcionará soporte y atención a los servicios de transporte público existentes en Cracovia, Polonia. La principal funcionalidad del sistema será consultar la posición de un determinado autobús o tranvía y mostrar su ubicación con exactitud. Para lograr esto, necesitaremos tres fases de desarrollo. En primer lugar, deberemos implementar un sistema que obtenga las coordenadas geográficas de los vehículos de transporte público en cada instante. A continuación, tendremos que registrar todos estos datos y almacenarlos en una base de datos en un servidor web. Por último, desarrollaremos un sistema cliente que realice consultas a tiempo real sobre estos datos almacenados, obteniendo la posición para una línea determinada y mostrando su ubicación con un marcador en el mapa. Para hacer el seguimiento de los vehículos, sería necesario tener acceso a una API pública que nos proporcionase la posición registrada por los GPS que integran cada uno de ellos. Como esta API no existe actualmente para los servicios de autobús, y para los tranvías es de uso meramente privado, desarrollaremos una segunda aplicación en Android que hará las funciones del lado servidor. En ella podremos elegir mediante una simple interfaz el número de línea y un código específico que identificará a cada vehículo en particular (e.g. podemos tener 6 tranvías recorriendo la red al mismo tiempo para la línea 24). Esta aplicación obtendrá las coordenadas geográficas del teléfono móvil, lo cual incluye latitud, longitud y orientación a través del proveedor GPS. De este modo, podremos realizar una simulación de como el sistema funcionará a tiempo real utilizando la aplicación servidora desde dentro de un tranvía o autobús y, al mismo tiempo, utilizando la aplicación cliente haciendo peticiones para mostrar la información de dicho tranvía. El cliente, además, podrá consultar la ruta de cualquier línea sin necesidad de tener acceso a Internet. Almacenaremos las rutas y paradas de cada línea en la memoria del teléfono móvil utilizando ficheros XML debido al poco espacio que ocupan y a lo útil que resulta poder consultar un trayecto en cualquier momento, independientemente del acceso a la red. El usuario también podrá consultar las tablas de horarios oficiales para cada línea. Aunque en este caso si será necesaria una conexión a Internet debido a que se realizará a través de la web oficial de MPK. Para almacenar todas las coordenadas de cada vehículo en cada instante necesitaremos crear una base de datos en un servidor. Esto se resolverá mediante el uso de MYSQL y PHP. Se enviarán peticiones de tipo GET y POST a los servicios PHP que se encargarán de traducir y realizar la consulta correspondiente a la base de datos MYSQL. Por último, gracias a todos los datos recogidos relativos a la posición de los vehículos de transporte público, podremos realizar algunas tareas de análisis. Comparando la hora exacta a la que los vehículos pasaron por cada parada y la hora a la que deberían haber pasado según los horarios oficiales, podremos descubrir fallos en estos. Seremos capaces de determinar si es un error puntual debido a factores externos (atascos, averías,…) o si por el contrario, es algo que ocurre muy a menudo y se debería corregir el horario oficial. ABSTRACT The aim of this final Project (for University) is to develop an Android application thatwill provide support and feedback to the public transport services in Krakow. The main functionality of the system will be to track the position of a desired bus or tram line, and display its position on the map. To achieve this, we will need 3 stages: the first one will be to implement a system that sends the geographical position of the public transport vehicles, the second one will be to collect this data in a web server, and the last one will be to get the last location registered for the desired line and display it on the map. For tracking the vehicles, we would need to have access to a public API that should be connected with each bus/tram GPS. As this doesn’t exist in Krakow or at least is not available for public use, we will develop a second android application that will do the server side job. We will be able to choose in a simple interface the line number and a code letter to identify each vehicle (e.g. we can have 6 trams that belong to the line number 24 working at the same time). It will take the current mobile geolocation; this includes getting latitude, longitude and bearing from the GPS provider. Thus, we will be able to make a simulation of how the system works in real time by using the server app inside a tram and at the same time, using the client app and making requests to display the information of that tram. The client will also be able to check the path of the desired line without internet access. We will store the path and stops for each line locally in the phone memory using xml files due to the few requirements of available space it needs and the usefulness of checking a path when needed. This app will also offer the functionality of checking the timetable for the line, but in this case, it will link to the official Mpk website, so Internet access will be required. For storing all the coordinates for each vehicle at every moment we will need to create a database on a server. We have decided that the easiest way is to use Mysql and PHP for the deployment of the service. We will send GET and POST requests to the php files and those files will make the according queries to our database. Finally, based on all the collected data, we will be able to get some information about errors in the system of public transport timetables. We will check at what time a line was in each specific stop and compare it with the official timetable to find mistakes of time. We will determine if it is something that happens occasionally and related to external factors (e.g. traffic jams, breakdowns…) or if on the other hand, it is something that happens very often and the public transport timetables should be looked over and corrected.

Hyperspectral to multispectral imaging for detection of tree nuts and peanut traces in wheat flour

In current industrial environments there is an increasing need for practical and inexpensive quality control systems to detect the foreign food materials in powder food processing lines. This demand is especially important for the detection of product adulteration with traces of highly allergenic products, such as peanuts and tree nuts. Manufacturing industries dealing with the processing of multiple powder food products present a substantial risk for the contamination of powder foods with traces of tree nuts and other adulterants, which might result in unintentional ingestion of nuts by the sensitised population. Hence, the need for an in-line system to detect nut traces at the early stages of food manufacturing is of crucial importance. In this present work, a feasibility study of a spectral index for revealing adulteration of tree nut and peanut traces in wheat flour samples with hyperspectral images is reported. The main nuts responsible for allergenic reactions considered in this work were peanut, hazelnut and walnut. Enhanced contrast between nuts and wheat flour was obtained after the application of the index. Furthermore, the segmentation of these images by selecting different thresholds for different nut and flour mixtures allowed the identification of nut traces in the samples. Pixels identified as nuts were counted and compared with the actual percentage of peanut adulteration. As a result, the multispectral system was able to detect and provide good visualisation of tree nut and peanut trace levels down to 0.01% by weight. In this context, multispectral imaging could operate in conjuction with chemical procedures, such as Real Time Polymerase Chain Reaction and Enzyme-Linked Immunosorbent Assay to save time, money and skilled labour on product quality control. This approach could enable not only a few selected samples to be assessed but also to extensively incorporate quality control surveyance on product processing lines.

Hyperspectral to multispectral imaging for detection of tree nuts and peanut traces in wheat flour.

In current industrial environments there is an increasing need for practical and inexpensive quality control systems to detect the foreign food materials in powder food processing lines. This demand is especially important for the detection of product adulteration with traces of highly allergenic products, such as peanuts and tree nuts. Manufacturing industries dealing with the processing of multiple powder food products present a substantial risk for the contamination of powder foods with traces of tree nuts and other adulterants, which might result in unintentional ingestion of nuts by the sensitised population. Hence, the need for an in-line system to detect nut traces at the early stages of food manufacturing is of crucial importance. In this present work, a feasibility study of a spectral index for revealing adulteration of tree nut and peanut traces in wheat flour samples with hyperspectral images is reported. The main nuts responsible for allergenic reactions considered in this work were peanut, hazelnut and walnut. Enhanced contrast between nuts and wheat flour was obtained after the application of the index. Furthermore, the segmentation of these images by selecting different thresholds for different nut and flour mixtures allowed the identification of nut traces in the samples. Pixels identified as nuts were counted and with the actual percentage of peanut adulteration. As a result, the multispectral system was able to detect and provide good visualisation of tree nut and peanut trace levels down to 0.01% by weight. In this context, multispectral imaging could operate in conjuction with chemical procedures, such as Real Time Polymerase Chain Reaction and Enzyme-Linked Immunosorbent Assay to save time, money and skilled labour on product quality control. This approach could enable not only a few selected samples to be assessed but also to extensively incorporate quality control surveyance on product processing lines.

Modelo para la integración del trazado de infraestructuras lineales en el paisaje y el medio ambiente basado en SIG

El análisis de las diferentes alternativas en la planificación y diseño de corredores y trazados de carreteras debe basarse en la correcta definición de variables territoriales que sirvan como criterios para la toma de decisión y esto requiere un análisis ambiental preliminar de esas variables de calidad. En España, los estudios de viabilidad de nuevas carreteras y autovías están asociados a una fase del proceso de decisión que se corresponde con el denominado Estudio Informativo, el cual establece condicionantes físicos, ambientales, de uso del suelo y culturales que deben ser considerados en las primeras fases de la definición del trazado de un corredor de carretera. Así, la metodología más frecuente es establecer diferentes niveles de capacidad de acogida del territorio en el área de estudio con el fin de resumir las variables territoriales en mapas temáticos y facilitar el proceso de trazado de las alternativas de corredores de carretera. El paisaje es un factor limitante a tener en cuenta en la planificación y diseño de carreteras y, por tanto, deben buscarse trazados más sostenibles en relación con criterios estéticos y ecológicos del mismo. Pero este factor no es frecuentemente analizado en los Estudios Informativos e incluso, si es considerado, los estudios específicos de la calidad del paisaje (estético y ecológico) y de las formas del terreno no incorporan las recomendaciones de las guías de trazado para evitar o reducir los impactos en el paisaje. Además, los mapas de paisaje que se generan en este tipo de estudios no se corresponden con la escala de desarrollo del Estudio Informativo (1:5.000). Otro déficit común en planificación de corredores y trazados de carreteras es que no se tiene en cuenta la conectividad del paisaje durante el proceso de diseño de la carretera para prevenir la afección a los corredores de fauna existentes en el paisaje. Este déficit puede originar un posterior efecto barrera en los movimientos dispersivos de la fauna y la fragmentación de sus hábitats debido a la ocupación parcial o total de las teselas de hábitats con importancia biológica para la fauna (o hábitats focales) y a la interrupción de los corredores de fauna que concentran esos movimientos dispersivos de la fauna entre teselas. El objetivo principal de esta tesis es mejorar el estudio del paisaje para prevenir su afección durante el proceso de trazado de carreteras, facilitar la conservación de los corredores de fauna (o pasillos verdes) y la localización de medidas preventivas y correctoras en términos de selección y cuantificación de factores de idoneidad a fin de reducir los impactos visuales y ecológicos en el paisaje a escala local. Concretamente, la incorporación de valores cuantitativos y bien justificados en el proceso de decisión permite incrementar la transparencia en el proceso de diseño de corredores y trazados de carreteras. Con este fin, se han planteado cuatro preguntas específicas en esta investigación (1) ¿Cómo se seleccionan y evalúan los factores territoriales limitantes para localizar una nueva carretera por los profesionales españoles de planificación del territorio en relación con el paisaje? (2) ¿Cómo pueden ser definidos los corredores de fauna a partir de factores del paisaje que influyen en los movimientos dispersivos de la fauna? (3) ¿Cómo pueden delimitarse y evaluarse los corredores de fauna incluyendo el comportamiento parcialmente errático en los movimientos dispersivos de la fauna y el efecto barrera de los elementos antrópicos a una escala local? (4) ¿Qué y cómo las recomendaciones de diseño de carreteras relacionadas con el paisaje y las formas del terreno pueden ser incluidas en un modelo de Sistemas de Información Geográfica (SIG) para ayudar a los ingenieros civiles durante el proceso de diseño de un trazado de carreteras bajo el punto de vista de la sostenibilidad?. Esta tesis doctoral propone nuevas metodologías que mejoran el análisis visual y ecológico del paisaje utilizando indicadores y modelos SIG para obtener alternativas de trazado que produzcan un menor impacto en el paisaje. Estas metodologías fueron probadas en un paisaje heterogéneo con una alta tasa de densidad de corzo (Capreolus capreolus L.), uno de los grandes mamíferos más atropellados en la red de carreteras españolas, y donde está planificada la construcción de una nueva autovía que atravesará la mitad del área de distribución del corzo. Inicialmente, se han analizado las variables utilizadas en 22 estudios de proyectos de planificación de corredores de carreteras promovidos por el Ministerio de Fomento entre 2006 y 2008. Estas variables se agruparon según condicionantes físicos, ambientales, de usos del suelo y culturales con el fin de comparar los valores asignados de capacidad de acogida del territorio a cada variable en los diferentes estudios revisados. Posteriormente, y como etapa previa de un análisis de conectividad, se construyó un mapa de resistencia de los movimientos dispersivos del corzo en base a la literatura y al juicio de expertos. Usando esta investigación como base, se le asignó un valor de resistencia a cada factor seleccionado para construir la matriz de resistencia, ponderándolo y combinándolo con el resto de factores usando el proceso analítico jerárquico y los operadores de lógica difusa como métodos de análisis multicriterio. Posteriormente, se diseñó una metodología SIG para delimitar claramente la extensión física de los corredores de fauna de acuerdo a un valor umbral de ancho geométrico mínimo, así como la existencia de múltiples potenciales conexiones entre cada par de teselas de hábitats presentes en el paisaje estudiado. Finalmente, se realizó un procesado de datos Light Detection and Ranging (LiDAR) y un modelo SIG para calcular la calidad del paisaje (estético y ecológico), las formas del terreno que presentan características similares para trazar una carretera y la acumulación de vistas de potenciales conductores y observadores de los alrededores de la nueva vía. Las principales contribuciones de esta investigación al conocimiento científico existente en el campo de la evaluación del impacto ambiental en relación al diseño de corredores y trazados de carreteras son cuatro. Primero, el análisis realizado de 22 Estudios Informativos de planificación de carreteras reveló que los métodos aplicados por los profesionales para la evaluación de la capacidad de acogida del territorio no fue suficientemente estandarizada, ya que había una falta de uniformidad en el uso de fuentes cartográficas y en las metodologías de evaluación de la capacidad de acogida del territorio, especialmente en el análisis de la calidad del paisaje estético y ecológico. Segundo, el análisis realizado en esta tesis destaca la importancia de los métodos multicriterio para estructurar, combinar y validar factores que limitan los movimientos dispersivos de la fauna en el análisis de conectividad. Tercero, los modelos SIG desarrollados Generador de alternativas de corredores o Generator of Alternative Corridors (GAC) y Eliminador de Corredores Estrechos o Narrow Corridor Eraser (NCE) pueden ser aplicados sistemáticamente y sobre una base científica en análisis de conectividad como una mejora de las herramientas existentes para la comprensión el paisaje como una red compuesta por nodos y enlaces interconectados. Así, ejecutando los modelos GAC y NCE de forma iterativa, pueden obtenerse corredores alternativos con similar probabilidad de ser utilizados por la fauna y sin que éstos presenten cuellos de botella. Cuarto, el caso de estudio llevado a cabo de prediseño de corredores y trazado de una nueva autovía ha sido novedoso incluyendo una clasificación semisupervisada de las formas del terreno, filtrando una nube de puntos LiDAR e incluyendo la nueva geometría 3D de la carretera en el Modelo Digital de Superficie (MDS). El uso combinado del procesamiento de datos LiDAR y de índices y clasificaciones geomorfológicas puede ayudar a los responsables encargados en la toma de decisiones a evaluar qué alternativas de trazado causan el menor impacto en el paisaje, proporciona una visión global de los juicios de valor más aplicados y, en conclusión, define qué medidas de integración paisajística correctoras deben aplicarse y dónde. ABSTRACT The assessment of different alternatives in road-corridor planning and layout design must be based on a number of well-defined territorial variables that serve as decision-making criteria, and this requires a high-quality preliminary environmental analysis of those quality variables. In Spain, feasibility studies for new roads and motorways are associated to a phase of the decision procedure which corresponds with the one known as the Informative Study, which establishes the physical, environmental, land-use and cultural constraints to be considered in the early stages of defining road corridor layouts. The most common methodology is to establish different levels of Territorial Carrying Capacity (TCC) in the study area in order to summarize the territorial variables on thematic maps and facilitate the tracing process of road-corridor layout alternatives. Landscape is a constraint factor that must be considered in road planning and design, and the most sustainable layouts should be sought based on aesthetic and ecological criteria. However this factor is not often analyzed in Informative Studies and even if it is, baseline studies on landscape quality (aesthetic and ecological) and landforms do not usually include the recommendations of road tracing guides designed to avoid or reduce impacts on the landscape. The resolution of the landscape maps produced in this type of studies does not comply with the recommended road design scale (1:5,000) in the regulations for the Informative Study procedure. Another common shortcoming in road planning is that landscape ecological connectivity is not considered during road design in order to avoid affecting wildlife corridors in the landscape. In the prior road planning stage, this issue could lead to a major barrier effect for fauna dispersal movements and to the fragmentation of their habitat due to the partial or total occupation of habitat patches of biological importance for the fauna (or focal habitats), and the interruption of wildlife corridors that concentrate fauna dispersal movements between patches. The main goal of this dissertation is to improve the study of the landscape and prevent negative effects during the road tracing process, and facilitate the preservation of wildlife corridors (or green ways) and the location of preventive and corrective measures by selecting and quantifying suitability factors to reduce visual and ecological landscape impacts at a local scale. Specifically the incorporation of quantitative and well-supported values in the decision-making process provides increased transparency in the road corridors and layouts design process. Four specific questions were raised in this research: (1) How are territorial constraints selected and evaluated in terms of landscape by Spanish land-planning practitioners before locating a new road? (2) How can wildlife corridors be defined based on the landscape factors influencing the dispersal movements of fauna? (3) How can wildlife corridors be delimited and assessed to include the partially erratic movements of fauna and the barrier effect of the anthropic elements at a local scale? (4) How recommendations of road design related to landscape and landforms can be included in a Geographic Information System (GIS) model to aid civil engineers during the road layout design process and support sustainable development? This doctoral thesis proposes new methodologies that improve the assessment of the visual and ecological landscape character using indicators and GIS models to obtain road layout alternatives with a lower impact on the landscape. These methodologies were tested on a case study of a heterogeneous landscape with a high density of roe deer (Capreolus capreolus L.) –one of the large mammals most commonly hit by vehicles on the Spanish road network– and where a new motorway is planned to pass through the middle of their distribution area. We explored the variables used in 22 road-corridor planning projects sponsored by the Ministry of Public Works between 2006 and 2008. These variables were grouped into physical, environmental, land-use and cultural constraints for the purpose of comparing the TCC values assigned to each variable in the various studies reviewed. As a prior stage in a connectivity analysis, a map of resistance to roe deer dispersal movements was created based on the literature and experts judgment. Using this research as a base, each factor selected to build the matrix was assigned a resistance value and weighted and combined with the rest of the factors using the analytic hierarchy process (AHP) and fuzzy logic operators as multicriteria assessment (MCA) methods. A GIS methodology was designed to clearly delimit the physical area of wildlife corridors according to a geometric threshold width value, and the multiple potential connections between each pair of habitat patches in the landscape. A Digital Surface Model Light Detection and Ranging (LiDAR) dataset processing and a GIS model was performed to determine landscape quality (aesthetic and ecological) and landforms with similar characteristics for the road layout, and the cumulative viewshed of potential drivers and observers in the area surrounding the new motorway. The main contributions of this research to current scientific knowledge in the field of environmental impact assessment for road corridors and layouts design are four. First, the analysis of 22 Informative Studies on road planning revealed that the methods applied by practitioners for assessing the TCC were not sufficiently standardized due to the lack of uniformity in the cartographic information sources and the TCC valuation methodologies, especially in the analysis of the aesthetic and ecological quality of the landscape. Second, the analysis in this dissertation highlights the importance of multicriteria methods to structure, combine and validate factors that constrain wildlife dispersal movements in the connectivity analysis. Third, the “Generator of Alternative Corridors (GAC)” and “Narrow Corridor Eraser (NCE)” GIS models developed can be applied systematically and on a scientific basis in connectivity analyses to improve existing tools and understand landscape as a network composed of interconnected nodes and links. Thus, alternative corridors with similar probability of use by fauna and without bottlenecks can be obtained by iteratively running GAC and NCE models. Fourth, our case study of new motorway corridors and layouts design innovatively included semi-supervised classification of landforms, filtering of LiDAR point clouds and new 3D road geometry on the Digital Surface Model (DSM). The combined used of LiDAR data processing and geomorphological indices and classifications can help decision-makers assess which road layouts produce lower impacts on the landscape, provide an overall insight into the most commonly applied value judgments, and in conclusion, define which corrective measures should be applied in terms of landscaping, and where.

Optimización de la agitación de un digestor anaerobio mediante mecánica de fluidos computacional

Debido al gran interés existente en el ahorro y recuperación de energía, y en el deseo de obtener productos que permitan usos beneficiosos del fango procedente de la depuración del agua residual, la digestión anaerobia es el proceso de estabilización de uso más extendido. El tiempo de retención de sólidos es un factor clave en el proceso de digestión anaerobia. En base al tiempo de retención de sólidos, se dimensiona el volumen de los digestores anaerobios para así obtener la reducción de materia orgánica deseada, con la correspondiente producción de biogás. La geometría del digestor y su sistema de agitación deben ser adecuados para alcanzar el tiempo de retención de sólidos de diseño. Los primeros trabajos sobre la agitación de los digestores realizaban únicamente experimentos con trazadores y otros métodos de medición. En otros casos, la mezcla era evaluada mediante la producción de biogás. Estas técnicas tenían el gran hándicap de no conocer lo que sucedía realmente dentro del digestor y sólo daban una idea aproximada de su funcionamiento. Mediante aplicación de la mecánica de fluidos computacional (CFD) es posible conocer con detalle las características del fluido objeto de estudio y, por lo tanto, simular perfectamente el movimiento del fango de un digestor anaerobio. En esta tesis se han simulado mediante CFD diferentes digestores a escala real (unos 2000 m3 de volumen) agitados con bomba/s de recirculación para alcanzar los siguientes objetivos: establecer la influencia de la relación entre el diámetro y la altura, de la pendiente de la solera, del número de bombas y del caudal de recirculación en dichos digestores, definir el campo de velocidades en la masa de fango y realizar un análisis energético y económico. Así, es posible conocer mejor cómo funciona el sistema de agitación de un digestor anaerobio a escala real equipado con bomba/s de recirculación. Los resultados obtenidos muestran que una relación diámetro/altura del digestor por encima de 1 empeora la agitación del mismo y que la pendiente en la solera del digestor favorece que la masa de fango esté mejor mezclada, siendo más determinante la esbeltez del tanque que la pendiente de su solera. No obstante, también es necesario elegir adecuadamente los parámetros de diseño del sistema de agitación, en este caso el caudal de recirculación de fango, para obtener una agitación completa sin apenas zonas muertas. En el caso de un digestor con una geometría inadecuada es posible mejorar su agitación aumentando el número de bombas de recirculación y el caudal de las mismas, pero no se llegará a alcanzar una agitación total de la masa de fango debido a su mal diseño original. Anaerobic digestion is the process for waste water treatment sludge stabilization of more widespread use due to the huge interest in saving and recovering energy and the wish to obtain products that allow beneficial uses for the sludge. The solids retention time is a key factor in the anaerobic digestion. Based on the solids retention time, volume anaerobic digester is sized to obtain the desired reduction in organic matter, with the corresponding production of biogas. The geometry of the digester and the stirring system should be adequate to achieve the design solid retention time. Early works on digesters stirring just performed tracer experiments and other measurement methods. In other cases, mixing was evaluated by biogas production. These techniques had the great handicap of not knowing what really happened inside the digester and they only gave a rough idea of its operation. By application of computational fluid dynamics (CFD), it is possible to know in detail the characteristics of the fluid under study and, therefore, simulate perfectly the sludge movement of an anaerobic digester. Different full-scale digesters (about 2000 m3 of volume) agitated with pump/s recirculation have been simulated by CFD in this thesis to achieve the following objectives: to establish the influence of the relationship between the diameter and height, the slope of the bottom, the number of pumps and the recirculation flow in such digesters, to define the velocity field in the mass of sludge and carry out an energy and economic analysis. Thus, it is possible to understand better how the agitation system of a full-scale anaerobic digester equipped with pump/s recirculation works. The results achieved show that a diameter/height ratio of the digester above 1 worsens its stirring and that the slope of the digester bottom favors that the mass of sludge is better mixed, being more decisive the tank slenderness than the slope of its bottom. However, it is also necessary to select properly the design parameters of the agitation system, in this case the sludge recirculation flow rate, for a complete agitation with little dead zones. In the case of a digester with inadequate geometry, its agitation can be improved by increasing the number of recirculation pumps and flow of them, but it will not reach a full agitation of the mass of sludge because of the poor original design.

Trust-ware: A Methodology to Analyze, Design, and Secure Trust and Reputation Systems

Entendemos por inteligencia colectiva una forma de inteligencia que surge de la colaboración y la participación de varios individuos o, siendo más estrictos, varias entidades. En base a esta sencilla definición podemos observar que este concepto es campo de estudio de las más diversas disciplinas como pueden ser la sociología, las tecnologías de la información o la biología, atendiendo cada una de ellas a un tipo de entidades diferentes: seres humanos, elementos de computación o animales. Como elemento común podríamos indicar que la inteligencia colectiva ha tenido como objetivo el ser capaz de fomentar una inteligencia de grupo que supere a la inteligencia individual de las entidades que lo forman a través de mecanismos de coordinación, cooperación, competencia, integración, diferenciación, etc. Sin embargo, aunque históricamente la inteligencia colectiva se ha podido desarrollar de forma paralela e independiente en las distintas disciplinas que la tratan, en la actualidad, los avances en las tecnologías de la información han provocado que esto ya no sea suficiente. Hoy en día seres humanos y máquinas a través de todo tipo de redes de comunicación e interfaces, conviven en un entorno en el que la inteligencia colectiva ha cobrado una nueva dimensión: ya no sólo puede intentar obtener un comportamiento superior al de sus entidades constituyentes sino que ahora, además, estas inteligencias individuales son completamente diferentes unas de otras y aparece por lo tanto el doble reto de ser capaces de gestionar esta gran heterogeneidad y al mismo tiempo ser capaces de obtener comportamientos aún más inteligentes gracias a las sinergias que los distintos tipos de inteligencias pueden generar. Dentro de las áreas de trabajo de la inteligencia colectiva existen varios campos abiertos en los que siempre se intenta obtener unas prestaciones superiores a las de los individuos. Por ejemplo: consciencia colectiva, memoria colectiva o sabiduría colectiva. Entre todos estos campos nosotros nos centraremos en uno que tiene presencia en la práctica totalidad de posibles comportamientos inteligentes: la toma de decisiones. El campo de estudio de la toma de decisiones es realmente amplio y dentro del mismo la evolución ha sido completamente paralela a la que citábamos anteriormente en referencia a la inteligencia colectiva. En primer lugar se centró en el individuo como entidad decisoria para posteriormente desarrollarse desde un punto de vista social, institucional, etc. La primera fase dentro del estudio de la toma de decisiones se basó en la utilización de paradigmas muy sencillos: análisis de ventajas e inconvenientes, priorización basada en la maximización de algún parámetro del resultado, capacidad para satisfacer los requisitos de forma mínima por parte de las alternativas, consultas a expertos o entidades autorizadas o incluso el azar. Sin embargo, al igual que el paso del estudio del individuo al grupo supone una nueva dimensión dentro la inteligencia colectiva la toma de decisiones colectiva supone un nuevo reto en todas las disciplinas relacionadas. Además, dentro de la decisión colectiva aparecen dos nuevos frentes: los sistemas de decisión centralizados y descentralizados. En el presente proyecto de tesis nos centraremos en este segundo, que es el que supone una mayor atractivo tanto por las posibilidades de generar nuevo conocimiento y trabajar con problemas abiertos actualmente así como en lo que respecta a la aplicabilidad de los resultados que puedan obtenerse. Ya por último, dentro del campo de los sistemas de decisión descentralizados existen varios mecanismos fundamentales que dan lugar a distintas aproximaciones a la problemática propia de este campo. Por ejemplo el liderazgo, la imitación, la prescripción o el miedo. Nosotros nos centraremos en uno de los más multidisciplinares y con mayor capacidad de aplicación en todo tipo de disciplinas y que, históricamente, ha demostrado que puede dar lugar a prestaciones muy superiores a otros tipos de mecanismos de decisión descentralizados: la confianza y la reputación. Resumidamente podríamos indicar que confianza es la creencia por parte de una entidad que otra va a realizar una determinada actividad de una forma concreta. En principio es algo subjetivo, ya que la confianza de dos entidades diferentes sobre una tercera no tiene porqué ser la misma. Por otro lado, la reputación es la idea colectiva (o evaluación social) que distintas entidades de un sistema tiene sobre otra entidad del mismo en lo que respecta a un determinado criterio. Es por tanto una información de carácter colectivo pero única dentro de un sistema, no asociada a cada una de las entidades del sistema sino por igual a todas ellas. En estas dos sencillas definiciones se basan la inmensa mayoría de sistemas colectivos. De hecho muchas disertaciones indican que ningún tipo de organización podría ser viable de no ser por la existencia y la utilización de los conceptos de confianza y reputación. A partir de ahora, a todo sistema que utilice de una u otra forma estos conceptos lo denominaremos como sistema de confianza y reputación (o TRS, Trust and Reputation System). Sin embargo, aunque los TRS son uno de los aspectos de nuestras vidas más cotidianos y con un mayor campo de aplicación, el conocimiento que existe actualmente sobre ellos no podría ser más disperso. Existen un gran número de trabajos científicos en todo tipo de áreas de conocimiento: filosofía, psicología, sociología, economía, política, tecnologías de la información, etc. Pero el principal problema es que no existe una visión completa de la confianza y reputación en su sentido más amplio. Cada disciplina focaliza sus estudios en unos aspectos u otros dentro de los TRS, pero ninguna de ellas trata de explotar el conocimiento generado en el resto para mejorar sus prestaciones en su campo de aplicación concreto. Aspectos muy detallados en algunas áreas de conocimiento son completamente obviados por otras, o incluso aspectos tratados por distintas disciplinas, al ser estudiados desde distintos puntos de vista arrojan resultados complementarios que, sin embargo, no son aprovechados fuera de dichas áreas de conocimiento. Esto nos lleva a una dispersión de conocimiento muy elevada y a una falta de reutilización de metodologías, políticas de actuación y técnicas de una disciplina a otra. Debido su vital importancia, esta alta dispersión de conocimiento se trata de uno de los principales problemas que se pretenden resolver con el presente trabajo de tesis. Por otro lado, cuando se trabaja con TRS, todos los aspectos relacionados con la seguridad están muy presentes ya que muy este es un tema vital dentro del campo de la toma de decisiones. Además también es habitual que los TRS se utilicen para desempeñar responsabilidades que aportan algún tipo de funcionalidad relacionada con el mundo de la seguridad. Por último no podemos olvidar que el acto de confiar está indefectiblemente unido al de delegar una determinada responsabilidad, y que al tratar estos conceptos siempre aparece la idea de riesgo, riesgo de que las expectativas generadas por el acto de la delegación no se cumplan o se cumplan de forma diferente. Podemos ver por lo tanto que cualquier sistema que utiliza la confianza para mejorar o posibilitar su funcionamiento, por su propia naturaleza, es especialmente vulnerable si las premisas en las que se basa son atacadas. En este sentido podemos comprobar (tal y como analizaremos en más detalle a lo largo del presente documento) que las aproximaciones que realizan las distintas disciplinas que tratan la violación de los sistemas de confianza es de lo más variado. únicamente dentro del área de las tecnologías de la información se ha intentado utilizar alguno de los enfoques de otras disciplinas de cara a afrontar problemas relacionados con la seguridad de TRS. Sin embargo se trata de una aproximación incompleta y, normalmente, realizada para cumplir requisitos de aplicaciones concretas y no con la idea de afianzar una base de conocimiento más general y reutilizable en otros entornos. Con todo esto en cuenta, podemos resumir contribuciones del presente trabajo de tesis en las siguientes. • La realización de un completo análisis del estado del arte dentro del mundo de la confianza y la reputación que nos permite comparar las ventajas e inconvenientes de las diferentes aproximación que se realizan a estos conceptos en distintas áreas de conocimiento. • La definición de una arquitectura de referencia para TRS que contempla todas las entidades y procesos que intervienen en este tipo de sistemas. • La definición de un marco de referencia para analizar la seguridad de TRS. Esto implica tanto identificar los principales activos de un TRS en lo que respecta a la seguridad, así como el crear una tipología de posibles ataques y contramedidas en base a dichos activos. • La propuesta de una metodología para el análisis, el diseño, el aseguramiento y el despliegue de un TRS en entornos reales. Adicionalmente se exponen los principales tipos de aplicaciones que pueden obtenerse de los TRS y los medios para maximizar sus prestaciones en cada una de ellas. • La generación de un software que permite simular cualquier tipo de TRS en base a la arquitectura propuesta previamente. Esto permite evaluar las prestaciones de un TRS bajo una determinada configuración en un entorno controlado previamente a su despliegue en un entorno real. Igualmente es de gran utilidad para evaluar la resistencia a distintos tipos de ataques o mal-funcionamientos del sistema. Además de las contribuciones realizadas directamente en el campo de los TRS, hemos realizado aportaciones originales a distintas áreas de conocimiento gracias a la aplicación de las metodologías de análisis y diseño citadas con anterioridad. • Detección de anomalías térmicas en Data Centers. Hemos implementado con éxito un sistema de deteción de anomalías térmicas basado en un TRS. Comparamos la detección de prestaciones de algoritmos de tipo Self-Organized Maps (SOM) y Growing Neural Gas (GNG). Mostramos como SOM ofrece mejores resultados para anomalías en los sistemas de refrigeración de la sala mientras que GNG es una opción más adecuada debido a sus tasas de detección y aislamiento para casos de anomalías provocadas por una carga de trabajo excesiva. • Mejora de las prestaciones de recolección de un sistema basado en swarm computing y odometría social. Gracias a la implementación de un TRS conseguimos mejorar las capacidades de coordinación de una red de robots autónomos distribuidos. La principal contribución reside en el análisis y la validación de las mejoras increméntales que pueden conseguirse con la utilización apropiada de la información existente en el sistema y que puede ser relevante desde el punto de vista de un TRS, y con la implementación de algoritmos de cálculo de confianza basados en dicha información. • Mejora de la seguridad de Wireless Mesh Networks contra ataques contra la integridad, la confidencialidad o la disponibilidad de los datos y / o comunicaciones soportadas por dichas redes. • Mejora de la seguridad de Wireless Sensor Networks contra ataques avanzamos, como insider attacks, ataques desconocidos, etc. Gracias a las metodologías presentadas implementamos contramedidas contra este tipo de ataques en entornos complejos. En base a los experimentos realizados, hemos demostrado que nuestra aproximación es capaz de detectar y confinar varios tipos de ataques que afectan a los protocoles esenciales de la red. La propuesta ofrece unas velocidades de detección muy altas así como demuestra que la inclusión de estos mecanismos de actuación temprana incrementa significativamente el esfuerzo que un atacante tiene que introducir para comprometer la red. Finalmente podríamos concluir que el presente trabajo de tesis supone la generación de un conocimiento útil y aplicable a entornos reales, que nos permite la maximización de las prestaciones resultantes de la utilización de TRS en cualquier tipo de campo de aplicación. De esta forma cubrimos la principal carencia existente actualmente en este campo, que es la falta de una base de conocimiento común y agregada y la inexistencia de una metodología para el desarrollo de TRS que nos permita analizar, diseñar, asegurar y desplegar TRS de una forma sistemática y no artesanal y ad-hoc como se hace en la actualidad. ABSTRACT By collective intelligence we understand a form of intelligence that emerges from the collaboration and competition of many individuals, or strictly speaking, many entities. Based on this simple definition, we can see how this concept is the field of study of a wide range of disciplines, such as sociology, information science or biology, each of them focused in different kinds of entities: human beings, computational resources, or animals. As a common factor, we can point that collective intelligence has always had the goal of being able of promoting a group intelligence that overcomes the individual intelligence of the basic entities that constitute it. This can be accomplished through different mechanisms such as coordination, cooperation, competence, integration, differentiation, etc. Collective intelligence has historically been developed in a parallel and independent way among the different disciplines that deal with it. However, this is not enough anymore due to the advances in information technologies. Nowadays, human beings and machines coexist in environments where collective intelligence has taken a new dimension: we yet have to achieve a better collective behavior than the individual one, but now we also have to deal with completely different kinds of individual intelligences. Therefore, we have a double goal: being able to deal with this heterogeneity and being able to get even more intelligent behaviors thanks to the synergies that the different kinds of intelligence can generate. Within the areas of collective intelligence there are several open topics where they always try to get better performances from groups than from the individuals. For example: collective consciousness, collective memory, or collective wisdom. Among all these topics we will focus on collective decision making, that has influence in most of the collective intelligent behaviors. The field of study of decision making is really wide, and its evolution has been completely parallel to the aforementioned collective intelligence. Firstly, it was focused on the individual as the main decision-making entity, but later it became involved in studying social and institutional groups as basic decision-making entities. The first studies within the decision-making discipline were based on simple paradigms, such as pros and cons analysis, criteria prioritization, fulfillment, following orders, or even chance. However, in the same way that studying the community instead of the individual meant a paradigm shift within collective intelligence, collective decision-making means a new challenge for all the related disciplines. Besides, two new main topics come up when dealing with collective decision-making: centralized and decentralized decision-making systems. In this thesis project we focus in the second one, because it is the most interesting based on the opportunities to generate new knowledge and deal with open issues in this area, as well as these results can be put into practice in a wider set of real-life environments. Finally, within the decentralized collective decision-making systems discipline, there are several basic mechanisms that lead to different approaches to the specific problems of this field, for example: leadership, imitation, prescription, or fear. We will focus on trust and reputation. They are one of the most multidisciplinary concepts and with more potential for applying them in every kind of environments. Besides, they have historically shown that they can generate better performance than other decentralized decision-making mechanisms. Shortly, we say trust is the belief of one entity that the outcome of other entities’ actions is going to be in a specific way. It is a subjective concept because the trust of two different entities in another one does not have to be the same. Reputation is the collective idea (or social evaluation) that a group of entities within a system have about another entity based on a specific criterion. Thus, it is a collective concept in its origin. It is important to say that the behavior of most of the collective systems are based on these two simple definitions. In fact, a lot of articles and essays describe how any organization would not be viable if the ideas of trust and reputation did not exist. From now on, we call Trust an Reputation System (TRS) to any kind of system that uses these concepts. Even though TRSs are one of the most common everyday aspects in our lives, the existing knowledge about them could not be more dispersed. There are thousands of scientific works in every field of study related to trust and reputation: philosophy, psychology, sociology, economics, politics, information sciences, etc. But the main issue is that a comprehensive vision of trust and reputation for all these disciplines does not exist. Every discipline focuses its studies on a specific set of topics but none of them tries to take advantage of the knowledge generated in the other disciplines to improve its behavior or performance. Detailed topics in some fields are completely obviated in others, and even though the study of some topics within several disciplines produces complementary results, these results are not used outside the discipline where they were generated. This leads us to a very high knowledge dispersion and to a lack in the reuse of methodologies, policies and techniques among disciplines. Due to its great importance, this high dispersion of trust and reputation knowledge is one of the main problems this thesis contributes to solve. When we work with TRSs, all the aspects related to security are a constant since it is a vital aspect within the decision-making systems. Besides, TRS are often used to perform some responsibilities related to security. Finally, we cannot forget that the act of trusting is invariably attached to the act of delegating a specific responsibility and, when we deal with these concepts, the idea of risk is always present. This refers to the risk of generated expectations not being accomplished or being accomplished in a different way we anticipated. Thus, we can see that any system using trust to improve or enable its behavior, because of its own nature, is especially vulnerable if the premises it is based on are attacked. Related to this topic, we can see that the approaches of the different disciplines that study attacks of trust and reputation are very diverse. Some attempts of using approaches of other disciplines have been made within the information science area of knowledge, but these approaches are usually incomplete, not systematic and oriented to achieve specific requirements of specific applications. They never try to consolidate a common base of knowledge that could be reusable in other context. Based on all these ideas, this work makes the following direct contributions to the field of TRS: • The compilation of the most relevant existing knowledge related to trust and reputation management systems focusing on their advantages and disadvantages. • We define a generic architecture for TRS, identifying the main entities and processes involved. • We define a generic security framework for TRS. We identify the main security assets and propose a complete taxonomy of attacks for TRS. • We propose and validate a methodology to analyze, design, secure and deploy TRS in real-life environments. Additionally we identify the principal kind of applications we can implement with TRS and how TRS can provide a specific functionality. • We develop a software component to validate and optimize the behavior of a TRS in order to achieve a specific functionality or performance. In addition to the contributions made directly to the field of the TRS, we have made original contributions to different areas of knowledge thanks to the application of the analysis, design and security methodologies previously presented: • Detection of thermal anomalies in Data Centers. Thanks to the application of the TRS analysis and design methodologies, we successfully implemented a thermal anomaly detection system based on a TRS.We compare the detection performance of Self-Organized- Maps and Growing Neural Gas algorithms. We show how SOM provides better results for Computer Room Air Conditioning anomaly detection, yielding detection rates of 100%, in training data with malfunctioning sensors. We also show that GNG yields better detection and isolation rates for workload anomaly detection, reducing the false positive rate when compared to SOM. • Improving the performance of a harvesting system based on swarm computing and social odometry. Through the implementation of a TRS, we achieved to improve the ability of coordinating a distributed network of autonomous robots. The main contribution lies in the analysis and validation of the incremental improvements that can be achieved with proper use information that exist in the system and that are relevant for the TRS, and the implementation of the appropriated trust algorithms based on such information. • Improving Wireless Mesh Networks security against attacks against the integrity, confidentiality or availability of data and communications supported by these networks. Thanks to the implementation of a TRS we improved the detection time rate against these kind of attacks and we limited their potential impact over the system. • We improved the security of Wireless Sensor Networks against advanced attacks, such as insider attacks, unknown attacks, etc. Thanks to the TRS analysis and design methodologies previously described, we implemented countermeasures against such attacks in a complex environment. In our experiments we have demonstrated that our system is capable of detecting and confining various attacks that affect the core network protocols. We have also demonstrated that our approach is capable of rapid attack detection. Also, it has been proven that the inclusion of the proposed detection mechanisms significantly increases the effort the attacker has to introduce in order to compromise the network. Finally we can conclude that, to all intents and purposes, this thesis offers a useful and applicable knowledge in real-life environments that allows us to maximize the performance of any system based on a TRS. Thus, we deal with the main deficiency of this discipline: the lack of a common and complete base of knowledge and the lack of a methodology for the development of TRS that allow us to analyze, design, secure and deploy TRS in a systematic way.

A Reliable Open-Source System Architecture for the Fast Designing and Prototyping of Autonomous Multi-UAV Systems: Simulation and Experimentation

During the process of design and development of an autonomous Multi-UAV System, two main problems appear. The first one is the difficulty of designing all the modules and behaviors of the aerial multi-robot system. The second one is the difficulty of having an autonomous prototype of the system for the developers that allows to test the performance of each module even in an early stage of the project. These two problems motivate this paper. A multipurpose system architecture for autonomous multi-UAV platforms is presented. This versatile system architecture can be used by the system designers as a template when developing their own systems. The proposed system architecture is general enough to be used in a wide range of applications, as demonstrated in the paper. This system architecture aims to be a reference for all designers. Additionally, to allow for the fast prototyping of autonomous multi-aerial systems, an Open Source framework based on the previously defined system architecture is introduced. It allows developers to have a flight proven multi-aerial system ready to use, so that they can test their algorithms even in an early stage of the project. The implementation of this framework, introduced in the paper with the name of “CVG Quadrotor Swarm”, which has also the advantages of being modular and compatible with different aerial platforms, can be found at https://​github.​com/​Vision4UAV/​cvg_​quadrotor_​swarm with a consistent catalog of available modules. The good performance of this framework is demonstrated in the paper by choosing a basic instance of it and carrying out simulation and experimental tests whose results are summarized and discussed in this paper.

A nucleolar protein related to ribosomal protein L7 is required for an early step in large ribosomal subunit biogenesis

The Saccharomyces cerevisiae Rlp7 protein has extensive identity and similarity to the large ribosomal subunit L7 proteins and shares an RNA-binding domain with them. Rlp7p is not a ribosomal protein; however, it is encoded by an essential gene and therefore must perform a function essential for cell growth. In this report, we show that Rlp7p is a nucleolar protein that plays a critical role in processing of precursors to the large ribosomal subunit RNAs. Pulse–chase labeling experiments with Rlp7p-depleted cells reveal that neither 5.8SS, 5.8SL, nor 25S is produced, indicating that both the major and minor processing pathways are affected. Analysis of processing intermediates by primer extension indicates that Rlp7p-depleted cells accumulate the 27SA3 precursor RNA, which is normally the major substrate (85%) used to produce the 5.8S and 25S rRNAs, and the ratio of 27SBL to 27SBS precursors changes from approximately 1:8 to 8:1 (depleted cells). Because 27SA3 is the direct precursor to 27SBS, we conclude that Rlp7p is specifically required for the 5′ to 3′ exonucleolytic trimming of the 27SA3 into the 27SBS precursor. As it is essential for processing in both the major and minor pathways, we propose that Rlp7p may act as a specificity factor that binds precursor rRNAs and tethers the enzymes that carry out the early 5′ to 3′ exonucleolytic reactions that generate the mature rRNAs. Rlp7p may also be required for the endonucleolytic cleavage in internal transcribed spacer 2 that separates the 5.8S rRNA from the 25S rRNA.

Lamprey Dlx genes and early vertebrate evolution

Gnathostome vertebrates have multiple members of the Dlx family of transcription factors that are expressed during the development of several tissues considered to be vertebrate synapomorphies, including the forebrain, cranial neural crest, placodes, and pharyngeal arches. The Dlx gene family thus presents an ideal system in which to examine the relationship between gene duplication and morphological innovation during vertebrate evolution. Toward this end, we have cloned Dlx genes from the lamprey Petromyzon marinus, an agnathan vertebrate that occupies a critical phylogenetic position between cephalochordates and gnathostomes. We have identified four Dlx genes in P. marinus, whose orthology with gnathostome Dlx genes provides a model for how this gene family evolved in the vertebrate lineage. Differential expression of these lamprey Dlx genes in the forebrain, cranial neural crest, pharyngeal arches, and sensory placodes of lamprey embryos provides insight into the developmental evolution of these structures as well as a model of regulatory evolution after Dlx gene duplication events.

Involvement of the Ubiquitin/Proteasome System in Sorting of the Interleukin 2 Receptor β Chain to Late Endocytic Compartments

Down-regulation of cell surface growth factor receptors plays a key role in the tight control of cellular responses. Recent reports suggest that the ubiquitin system, in addition to participating in degradation by the proteasome of cytosolic and nuclear proteins, might also be involved in the down-regulation of various membrane receptors. We have previously characterized a signal in the cytosolic part of the interleukin 2 receptor β chain (IL2Rβ) responsible for its targeting to late endosomes/lysosomes. In this report, the role of the ubiquitin/proteasome system on the intracellular fate of IL2Rβ was investigated. Inactivation of the cellular ubiquitination machinery in ts20 cells, which express a thermolabile ubiquitin-activating enzyme E1, leads to a significant decrease in the degradation rate of IL2Rβ, with little effect on its internalization. In addition, we show that a fraction of IL2Rβ can be monoubiquitinated. Furthermore, mutation of the lysine residues of the cytosolic region of a chimeric receptor carrying the IL2Rβ targeting signal resulted in a decreased degradation rate. When cells expressing IL2Rβ were treated either by proteasome or lysosome inhibitors, a significant decrease in receptor degradation was observed. Our data show that ubiquitination is required for the sorting of IL2Rβ toward degradation. They also indicate that impairment of proteasome function might more generally affect intracellular routing.