Capsule permeability via polymer and protein ingress/egress.

Static incubation tests, where microcapsules and beads are contacted with polymer and protein solutions, have been developed for the characterization of permselective materials applied for bioartificial organs and drug delivery. A combination of polymer ingress, detected by size-exclusion chromatography, and protein ingress/ egress, assessed by gel electrophoresis, provides information regarding the diffusion kinetics, molar mass cutoff(MMCO) and permeability. This represents an improvement over existing permeability measurements that are based on the diffusion of a single type of solute. Specifically, the permeability of capsules based on alginate, cellulose sulfate, polymethylene-co-guanidine were characterized as a function of membrane thickness. Solid alginate beads were also evaluated. The MMCO of these capsules was estimated to be between 80 and 90 kDa using polymers, and between 116-150 kDa with proteins. Apparently, the globular shape of the proteins (radius of gyration (Rg) of 4.2-4.6 nm) facilitates their passage through the membrane, comparatively to the polysaccharide coil conformation (Rg of 6.5-8.3 nm). An increase of the capsule membrane thickness reduced these values. The MMCO of the beads, which do not have a membrane limiting their permselective properties, was higher, between 110 and 200 kDa with dextrans, and between 150 and 220 kDa with proteins. Therefore, although the permeability estimated with biologically relevant molecules is generally higher due to their lower radius of gyration, both the MMCO of synthetic and natural watersoluble polymers correlate well, and can be used as in vitro metrics for the immune protection ability of microcapsules and microbeads. This article shows, to the authors' knowledge, the first reported concordance between permeability measures based on model natural and biological macromolecules.

Teichuronic acid operon of Bacillus subtilis 168.

Sequence analysis reveals that the Bacillus subtilis 168 tuaABCDEFGH operon encodes enzymes required for the polymerization of teichuronic acid as well as for the synthesis of one of its precursors, the UDP-glucuronate. Mutants deficient in any of the tua genes, grown in batch cultures under conditions of phosphate limitation, were characterized by reduced amounts of uronate in their cell walls. The teichuronic acid operon belongs to the Pho regulon, as phosphate limitation induces its transcription. Placing the tuaABCDEFGH operon under the control of the inducible Pspac promoter allowed its constitutive expression independently of the phosphate concentration in the medium; the level of uronic acid in cell walls was dependent on the concentration of the inducer. Apparently, owing to an interdependence between teichoic and teichuronic acid incorporation into the cell wall, in examined growth conditions, the balance between the two polymers is maintained in order to insure a constant level of the wall negative charge.

Tight open knots.

The tightest open conformations of a few prime knots (3(1), 4(1), 5(1), 5(2), and 6(3)) found with the use of the SONO algorithm are presented and discussed. The conformations are obtained from the tightest closed conformations of the knots by cutting and opening them at different locations. The length of the rope engaged in each of the open conformations is calculated. The curvature and torsion profiles of the unique tightest conformations of the 3(1) and 4(1) open knots are presented and discussed. In particular, symmetry properties of the knots reflected within their curvature and torsion profiles are analysed. Connections with the physics of polymers are discussed.

Effects of corticosterone pellets on baseline and stress-induced corticosterone and corticosteroid-binding-globulin.

Exogenous administration of glucocorticoids is a widely used and efficient tool to investigate the effects of elevated concentrations of these hormones in field studies. Because the effects of corticosterone are dose and duration-dependent, the exact course of plasma corticosterone levels after exogenous administration needs to be known. We tested the performance of self-degradable corticosterone pellets (implanted under the skin) in elevating plasma corticosterone levels. We monitored baseline (sampled within 3min after capture) total corticosterone levels and investigated potential interactions with corticosteroid-binding-globulin (CBG) capacity and the endogenous corticosterone response to handling in Eurasian kestrel Falco tinnunculus and barn owl Tyto alba nestlings. Corticosterone pellets designed for a 7-day-release in rodents elevated circulating baseline total corticosterone during only 2-3 days compared to placebo-nestlings. Highest levels occurred 1-2days after implantation and levels decreased strongly thereafter. CBG capacity was also increased, resulting in a smaller, but still significant, increase in baseline free corticosterone levels. The release of endogenous corticosterone as a response to handling was strong in placebo-nestlings, but absent 2 and 8 days after corticosterone pellet implantation. This indicates a potential shut-down of the hypothalamo-pituitary-adrenal axis after the 2-3 days of elevated baseline corticosterone levels. 20 days after pellet implantation, the endogenous corticosterone response to handling of nestlings implanted with corticosterone pellets attained similar levels as in placebo-nestlings. Self-degradable pellets proved to be an efficient tool to artificially elevate circulating baseline corticosterone especially in field studies, requiring only one intervention. The resulting peak-like elevation of circulating corticosterone, the concomitant elevation of CBG capacity, and the absence of an endogenous corticosterone response to an acute stressor have to be taken into account.

Solubility of cytoskeletal proteins in immunohistochemistry and the influence of fixation.

For accurate and quantitative immunohistochemical localization of antigens it is crucial to know the solubility of tissue proteins and their degree of loss during processing. In this study we focused on the solubility of several cytoskeletal proteins in cat brain tissue at various ages and their loss during immunohistochemical procedures. We further examined whether fixation affected either solubility or immunocytochemical detectability of several cytoskeletal proteins. An assay was designed to measure the solubility of cytoskeletal proteins in cryostat sections. Quantity and quality of proteins lost or remaining in tissue were measured and analyzed by electrophoresis and immunoblots. Most microtubule proteins were found to be soluble in unfixed and alcohol fixed tissues. Furthermore, the microtubule proteins remaining in the tissue had a changed cellular distribution. In contrast, brain spectrin and all three neurofilament subunits were insoluble and remained in the tissue, allowing their immunocytochemical localization in alcohol-fixed tissue. Synapsin I, a protein associated with the spectrin cytoskeleton, was soluble, and aldehyde fixation is advised for its immunohistochemical localization. With aldehyde fixation, the immunoreactivity of some antibodies against neurofilament proteins was reduced in axons unveiling novel immunogenic sites in nuclei that may represent artifacts of fixation. In conclusion, protein solubility and the effects of fixation are influential factors in cytoskeletal immunohistochemistry, and should be considered before assessments for a quantitative distribution are made.

Laboratory and Field Evaluation of Biodegradable Polyesters for Sustained Release of Isometamidium and Ethidium

An overview is presented of the results obtained with biodegradable sustained release devices (SRDs) containing a mixture of polymers and either isometamidium (ISMM) or ethidium. Under controlled laboratory conditions (monthly challenge with tsetse flies infected with Trypanosoma congolense) the protection period in SRD treated cattle could be extended by a factor 2.8 (for ethidium) up to 4.2 (for ISMM) as compared to animals treated intramuscularly with the same drugs. Using a competitive drug ELISA ISMM concentrations were detected up to 330 days after the implantation of the SRDs, whereas after i.m. injection the drug was no longer present three to four months post treatment. Two field trials carried out in Mali under heavy tsetse challenge showed that the cumulative infection rate was significantly lower in the ISMM-SRD implanted cattle than in those which received ISMM intramuscularly. Using ethidium SRD, however, contradictory results were obtained in field trials in Zambia and in Mali. The potential advantages and inconvenients of the use of SRDs are discussed and suggestions are made in order to further improve the currently available devices.

The in vivo performance of magnetic particle-loaded injectable, in situ gelling, carriers for the delivery of local hyperthermia.

We investigated the use of in situ implant formation that incorporates superparamagnetic iron oxide nanoparticles (SPIONs) as a form of minimally invasive treatment of cancer lesions by magnetically induced local hyperthermia. We developed injectable formulations that form gels entrapping magnetic particles into a tumor. We used SPIONs embedded in silica microparticles to favor syringeability and incorporated the highest proportion possible to allow large heating capacities. Hydrogel, single-solvent organogel and cosolvent (low-toxicity hydrophilic solvent) organogel formulations were injected into human cancer tumors xenografted in mice. The thermoreversible hydrogels (poloxamer, chitosan), which accommodated 20% w/v of the magnetic microparticles, proved to be inadequate. Alginate hydrogels, however, incorporated 10% w/v of the magnetic microparticles, and the external gelation led to strong implants localizing to the tumor periphery, whereas internal gelation failed in situ. The organogel formulations, which consisted of precipitating polymers dissolved in single organic solvents, displayed various microstructures. A 8% poly(ethylene-vinyl alcohol) in DMSO containing 40% w/v of magnetic microparticles formed the most suitable implants in terms of tumor casting and heat delivery. Importantly, it is of great clinical interest to develop cosolvent formulations with up to 20% w/v of magnetic microparticles that show reduced toxicity and centered tumor implantation.

Synthesis of novel biomaterials in plants.

Metabolic engineering of plants allows the possibility of using crops for the synthesis of novel polymers having useful material properties. Strong and flexible protein-based polymers, which are based on the structure of silk and elastin have been synthesized in transgenic plants. A wide range of polyhydroxyalkanoates having properties ranging from stiff plastics to soft elastomers and glues have been synthesized in various compartments of plants, such as the cytoplasm, plastid and peroxisome. These plant biomaterials could replace, in part, the synthetic plastics, fibers and elastomers produced from petroleum, thus offering the advantage of renewability, sustainability and biodegradability.

Elaboració de membranes de fibra buida modificades amb nanopartícules metàl·liques per aplicacions catalítiques

Investigación producida a partir de una estancia en la Université Paul Sabatier, Toulouse III - CNRS, entre 2007 y 2009. Durante los últimos años la investigación centrada en nuevos materiales de tamaño nanoscòpico (nanopartículas, quantum dots, nanotubos de carbono,...) ha experimentado un crecimiento considerable debido a las especiales propiedades de los "nanoobjetos" con respecto a magnetismo, catálisis, conductividad eléctrica, etc ... Sin embargo, hoy en día todavía existen pocas aplicaciones de las nanopartículas en temas medioambientales. Uno de los motivos de esta situación es la posible toxicidad de los nanoobjetos, pero existe también una dificultad tecnológica dado que las nanopartículas tienden a agregarse y es muy difícil manipularlas sin que pierdan sus propiedades especiales. Así, aunque la preparación de materiales catalíticos nanoestructurados es muy interesante, es necesario definir nuevas estrategias para prepararlos. Este proyecto de investigación tiene como objetivo principal la preparación de nuevas membranas catalíticas con nanopartículas metálicas en el interior para aplicaciones de tratamiento de agua. La innovación principal de este proyecto consiste en que las nanopartículas no son introducidas en la matriz polimérica una vez preformadas sino que se hacen crecer en el interior de la matriz polimérica mediante una síntesis intermatricial. El único requisito es que la matriz polimérica contenga grupos funcionales capaces de interaccionar con los precursores de las nanopartículas. Una vez finalizado el proyecto se puede afirmar que se han logrado parte de los objetivos planteados inicialmente. Concreamente ha quedado demostrado que se pueden sintetizar nanopartículas metálicas de metales nobles (platino y paladio) en membranas de fibra hueca de micro- y ultrafiltración siguiendo dos metodologías diferentes: modificación fotoquímica de polímeros y deposición de multicapas de polielectrolitos. Los nuevos materiales son efectivos en la catálisis de reducción de un compuesto modelo (4-nitrofenol con borohidruro de sodio) y, en general, los resultados han sido satisfactorios. Sin embargo, se ha puesto de manifiesto que el uso de un reactivo que genera hidrógeno gas en contacto con la solución acuosa dificulta enormemente la implementación de la reacción catalítica al ser el medio de la membrana una matriz porosa. Así, como conclusión principal se puede decir que se han encontrado las limitaciones de esta aproximación y se sugieren dos posibilidades de continuidad: la utilización de las membranas sintetizadas en contactores gas-líquido o bien el estudio y optimización del sistema de membrana en configuración de membranas planas, un objetivo más asequible dada su menor complejidad. Esta investigación se ha realizado en el seno del “Laboratoire de Génie Chimique” de Toulouse y del Departamento de Química de la Michigan State University y ha sido posible gracias a un proyecto financiado por la “Agence National pour la Recherce” y al programa PERMEANT entre el CNRS y la NSF.

Prospects for biopolymer production in plants.

It is likely that during this century polymers based on renewable materials will gradually replace industrial polymers based on petrochemicals. This chapter gives an overview of the current status of research on plant biopolymers that are used as a material in non-food applications. We cover technical and scientific bottlenecks in the production of novel or improved materials, and the potential of using transgenic or alternative crops in overcoming these bottlenecks. Four classes of biopolymers will be discussed: starch, proteins, natural rubber, and poly-beta-hydroxyalkanoates. Renewable polymers produced by chemical polymerization of monomers derived from sugars, vegetable oil, or proteins, are not considered here.

The Bacillus subtilis Gne (GneA, GalE) protein can catalyse UDP-glucose as well as UDP-N-acetylglucosamine 4-epimerisation.

Mutations in the Bacillus subtilis gene that affect the activity of the uridine diphosphate (UDP)-N-acetylglucosamine (GlcNAc) 4-epimerase (EC 5.1.3.7) were shown to map to galE, the structural gene of the UDP-glucose (Glc) 4-epimerase (EC 5.1.3.2). This genetic evidence that the same enzyme can catalyse the epimerisation of hexoses as well as of their N-acetylated forms is confirmed by in vitro assays with purified enzyme. It appears that in B. subtilis, Gne (GneA, GalE) is involved in two distinct and essential functions, i.e., cell detoxification under certain growth conditions and the biosynthesis of anionic cell wall polymers. We discuss the evidence that such enzymes capable of utilizing both UDP-hexoses and UDP-N-acetylhexosamines are present in other organisms.

Local moderate magnetically induced hyperthermia using an implant formed in situ in a mouse tumor model.

Purpose: We investigate a new heat delivery technique for the local treatment of solid tumors. The technique involves injecting a formulation that solidifies to form an implant in situ. This implant entraps superparamagnetic iron oxide nanoparticles (SPIONs) embedded in silica microbeads for magnetically induced moderate hyperthermia. Particle entrapment prevents phagocytosis and distant migration of SPIONs. The implant can be repeatedly heated by magnetic induction. Methods: We evaluated heating and treatment efficacies by means of thermometry and survival studies in nude mice carrying subcutaneous human colocarcinomas. At day 1, we injected the formulation into the tumor. At day 2, a single 20-min hyperthermia treatment was delivered by 141-kHz magnetic induction using field strengths of 9 to 12 mT under thermometry. Results: SPIONs embedded in silica microbeads were effectively confined within the implant at the injection site. Heat-induced necro-apoptosis was assessed by histology on day 3. On average, 12 mT resulted in tumor temperature of 47.8 degrees C, and over 70% tumor necrosis that correlated to the heat dose (AUC = 282 degrees C.min). In contrast, a 9-mT field strength induced tumoral temperature of 40 degrees C (AUC = 131 degrees C.min) without morphologically identifiable necrosis. Survival after treatment with 10.5 or 12 mT fields was significantly improved compared to non-implanted and implanted controls. Median survival times were 27 and 37 days versus 12 and 21 days respectively. Conclusion: Five of eleven mice (45%) of the 12 mT group survived one year without any tumor recurrence, holding promise for tumor therapy using magnetically induced moderate hyperthermia through injectable implants.

Modelling the mechanical aspects of the curing process of magneto-sensitive elastomeric materials

In this paper, a phenomenologically motivated magneto-mechanically coupled finite strain elastic framework for simulating the curing process of polymers in the presence of a magnetic load is proposed. This approach is in line with previous works by Hossain and co-workers on finite strain curing modelling framework for the purely mechanical polymer curing (Hossain et al., 2009b). The proposed thermodynamically consistent approach is independent of any particular free energy function that may be used for the fully-cured magneto-sensitive polymer modelling, i.e. any phenomenological or micromechanical-inspired free energy can be inserted into the main modelling framework. For the fabrication of magneto-sensitive polymers, micron-size ferromagnetic particles are mixed with the liquid matrix material in the uncured stage. The particles align in a preferred direction with the application of a magnetic field during the curing process. The polymer curing process is a complex (visco) elastic process that transforms a fluid to a solid with time. Such transformation process is modelled by an appropriate constitutive relation which takes into account the temporal evolution of the material parameters appearing in a particular energy function. For demonstration in this work, a frequently used energy function is chosen, i.e. the classical Mooney-Rivlin free energy enhanced by coupling terms. Several representative numerical examples are demonstrated that prove the capability of our approach to correctly capture common features in polymers undergoing curing processes in the presence of a magneto-mechanical coupled load.

A viscous bioerodible poly(ortho ester) as a new biomaterial for intraocular application.

The biocompatibility of a viscous, hydrophobic, bioerodible poly(ortho ester) (POE) intended for intraocular application was investigated. POE was evaluated as a blank carrier and as containing modulators of degradation. Each formulation was injected intracamerally and intravitreally in rabbit eyes, and clinical and histological examinations were performed postoperatively for 2 weeks. In the case of intracameral injections, polymer biocompatibility appeared to depend on the amount injected in the anterior chamber. When 50 microL was administered, the polymer degraded within 2 weeks, and clinical observations showed good biocompatibility of POE with no toxicity to the ocular tissues or increase in intraocular pressure. The injection of a larger volume, 100 microL, of POE, appeared inappropriate because of direct contact of polymeric material with the corneal endothelium, and triggered reversible edema and inflammation in the anterior chamber of the eye that regressed after a few days. After intravitreal administration, POE was well tolerated and no inflammatory reaction developed during the observation period. The polymer degraded slowly, appearing as a round whitish bubble in the vitreous cavity. The presence of modulators of degradation both improved POE biocompatibility and prolonged polymer lifetime in the eye. POE appears to be a promising biomaterial for clinical intraocular application.

Geometry and physics of catenanes applied to the study of DNA replication.

The concept of ideal geometric configurations was recently applied to the classification and characterization of various knots. Different knots in their ideal form (i.e., the one requiring the shortest length of a constant-diameter tube to form a given knot) were shown to have an overall compactness proportional to the time-averaged compactness of thermally agitated knotted polymers forming corresponding knots. This was useful for predicting the relative speed of electrophoretic migration of different DNA knots. Here we characterize the ideal geometric configurations of catenanes (called links by mathematicians), i.e., closed curves in space that are topologically linked to each other. We demonstrate that the ideal configurations of different catenanes show interrelations very similar to those observed in the ideal configurations of knots. By analyzing literature data on electrophoretic separations of the torus-type of DNA catenanes with increasing complexity, we observed that their electrophoretic migration is roughly proportional to the overall compactness of ideal representations of the corresponding catenanes. This correlation does not apply, however, to electrophoretic migration of certain replication intermediates, believed up to now to represent the simplest torus-type catenanes. We propose, therefore, that freshly replicated circular DNA molecules, in addition to forming regular catenanes, may also form hemicatenanes.