Rapport från/Report from IEA Task-14 mötet/meeting on solar heating system, Hameln Tyskland/Germany August 1992

Participation as observer at the meeting of Task 14 of IEA's Solar Heating and Cooling Projects held in Hameln, Germany has led to greater understanding of interesting developments underway in several countries. This will be of use during the development of small scale systems suitable for Swedish conditions. A summary of the work carried out by the working groups within Task 14 is given, with emphasis on the Domestic Hot Water group. Experiences of low-flow systems from several countries are related, and the conclusion is drawn that the maximum theoretical possible increase in performance of 20% has not been achieved due to poor heat exchangers and poor stratification in the storage tanks. Positive developments in connecting tubes and pumps is noted. Further participation as observer in Task 14 meetings is desired, and is looked on favourably by the members of the group. Another conclusion is that SERC should carry on with work on Swedish storage tanks, with emphasis on better stratification and heat exchangers, and possible modelling of system components. Finally a German Do-it-Vourself kit is described and judged in comparison with prefabricated models and Swedish Do-it-Yourself kits.

Gas-filled, flat plate solar collectors

This work treats the thermal and mechanical performances of gas-filled, flat plate solar collectors in order to achieve a better performance than that of air filled collectors. The gases examined are argon, krypton and xenon which all have lower thermal conductivity than air. The absorber is formed as a tray connected to the glass. The pressure of the gas inside is near to the ambient and since the gas volume will vary as the temperature changes, there are potential risks for fatigue in the material. One heat transfer model and one mechanical model were built. The mechanical model gave stresses and information on the movements. The factors of safety were calculated from the stresses, and the movements were used as input for the heat transfer model where the thermal performance was calculated. It is shown that gas-filled, flat plate solar collectors can be designed to achieve good thermal performance at a competitive cost. The best yield is achieved with a xenon gas filling together with a normal thick absorber, where normal thick means a 0.25 mm copper absorber. However, a great deal of energy is needed to produce the xenon gas, and if this aspect is taken into account, the krypton filling is better. Good thermal performance can also be achieved using less material; a collector with a 0.1 mm thick copper absorber and the third best gas, which is argon, still gives a better operating performance than a common, commercially produced, air filled collector with a 0.25 mm absorber. When manufacturing gas-filled flat plate solar collectors, one way of decreasing the total material costs significantly, is by changing absorber material from copper to aluminium. Best yield per monetary outlay is given by a thin (0.3 mm) alu-minium absorber with an argon filling. A high factor of safety is achieved with thin absorbers, large absorber areas, rectangular constructions with long tubes and short distances between glass and absorber. The latter will also give a thin layer of gas which gives good thermal performance. The only doubtii ful construction is an argon filled collector with a normal thick (> 0.50 mm) aluminium absorber. In general, an assessment of the stresses for the proposed construction together with appropriate tests are recommended before manufacturing, since it is hard to predict the factor of safety; if one part is reinforced, some other parts can experience more stress and the factor of safety actually drops.

Growth of Australian shortfin eel (Anguilla Australis) elvers given different dietary protein and lipid levels

The Australian shortfin eel, Anguilla australis is a potential candidate for intensive aquaculture. The present study was undertaken to evaluate the growth of elvers (5.4 g ± 0.1 initial weight) fed with diets of varying protein and lipid content, and to assess the potential of using soya-bean meal as a dietary ingredient. A 10 week experiment was conducted at 24 (±1.0) °C by rearing fish, in 60 L conical fibre glass tanks using a closed recirculation system. Diets having protein concentrations of 40 or 50% (by dry weight) were tested at three lipid levels (15, 20, 25%); diets being designated P₄₀L₁₅, P₄₀L₂₀, P₄₀L₂₅, P₅₀L₁₅, etc. All these diets contained 5% soya-bean meal. In addition P₅₀L₂₀ diets were formulated to contain 10 and 20% soya-bean meal in the diet (Diets S1 & S2). Shortfin eel grew best on the P₅₀L₁₅ diet, with an average specific growth rate of 2.26%. Food conservation ratio (FCR) and Protein efficiency ratio (PER) ranged from 1.21 (P₅₀L₁₅) to 2.12 (P₄₀L₂₅), and 0.92 (P₅₀L₂₅) to 1.65 (P₅₀L₁₅), respectively. Based on all criteria the best growth performance of shortfin eel was on the P₅₀L₁₅ diet, followed by P₄₀L₂₀ and P₄₀L₁₅. At both protein levels fish reared on diets with 25% lipid performed poorly. The performance of shortfin eel was not affected by the amount of soya-bean meal in the diet, up to a maximum of 20% dietary inclusion. No significant differences in muscle protein were evident in shortfin eel reared on different dietary treatments, nor was the lipid content of muscle related to dietary lipid level.

Isolating conifer DNA: a superior polysaccharide elimination method

Genomic DNA was isolated from frozen needles of maturePinus radiata clones using a modified extraction technique incorporating cetyltrimethylammonium bromide (CTAB) for cell lysis. A high sodium chloride concentration (2 M) was used at 2 stages of the extraction procedure to eradicate polysaccharides, yielding pure genomic DNA suitable for restriction enzyme digestion and PCR amplification. Extractions were scaled down to suit 1.5-mL Eppendorf tubes, allowing easier handling and enhanced sterility.

Method for determining reaction rate of mild steel containers during melting of magnesium-aluminium alloys and effect of aluminium content on directionally solidified microstructures

A magnesium alloy of eutectic composition (33 wt-'%Al) was directionally solidified in mild steel tubes at two growth rates, 32 and 580 mum s(-1,) in a temperature gradient between 10 and 20 K mm(-1). After directional solidification, the composition of each specimen varied dramatically, from 32'%Al in the region that had remained solid to 18%Al (32 mum s(-1) specimen) and 13%Al (580 mum s(-1) specimen) at the plane that had been quenched from the eutectic temperature. As the aluminium content decreased, the microstructure contained an increasing volume fraction of primary magnesium dendrites and the eutectic morphology gradually changed from lamellar to partially divorced. The reduction in aluminium content was caused by the growth of an Al-Fe phase ahead of the Mg-Al growth front. Most of the growth of the Al-Fe phase occurred during the remelting period before directional solidification. The thickness of the Al-Fe phase increased with increased temperature and time of contact with the molten Mg-Al alloy. (C) 2003 Maney Publishing.

Rapid composite tube manufacture utilizing the quickstep™ process

In this study, a novel method for manufacturing composite tubes utilizing the Quickstep^TM process has been developed. Tubes manufactured from `quick-cure' Toray G83C prepreg have demonstrated highly repeatable axial crush behavior with an average specific energy absorption (SEA) of 86 kJ/kg. The cure cycle is optimized by comparing the results from compression, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and porosity testing. The tube lay-up is optimized using compression and porosity test results. The effect of changes in fiber-orientation on SEA is also investigated. Process development has resulted in a robust manufacturing method capable of producing fully cured, high performance composite tubes with a cure cycle of 7 min. This corresponds to a 95% reduction in time compared to an equivalent autoclave cycle.

A solar collector with the absorber divided by rectangular slots

A new solar absorber structure has been proposed and studied in this paper. The metal tubes running perpendicular to a set of parallel rectangular metal fins make the solar absorber with rectangular slots. Studies on the collector were theoretically carried out in the aspects of heat transfer, thermodynamics and . hydrodynamics. The calculating methods for calculating fin efficiency F and efficiency factors of the collector F' were obtained. The results showed that the new solar collector would have the higher efficiency and better performance at higher fluid temperature than that of the traditional flat-plate collectors. A collector prototype with the new structure was built and tested. The testing results agree with our theoretical results.

A comparison of pilling results tested with the ICI pill box and a new perspex™ pill box

Identical single jersey wool knit fabrics produced inconsistent results when tested on the same type of ICI pill box in 4 independence testing laboratories.  The hypothesis formulated to investigate this event was that continued pilling testing in the ICI pill box changes the frictional properties of the cork liners, resulting in the difference pilling ratings.  The aim of this study was to decrease the inconsistencies in the pilling results by replacing the conventional cork lined pill box with a Perspex^TM pill box.  The smae or similar pilling results found for several of the knit facots tested in the two difference pill boxes, while for others there were some significant differences found.  In addition, while using the Perspex^TM pill box observations of the movement of the pilling tubes during testing provided evidence of greater fabric-to-fabric abrasion, rather the expected high degree of fabric-to-cork abrasion (or fabric-to-Perspex^TM) during pilling testing.

Interactive television and the role of affective usability

This paper explores the importance of designing interfaces that evoke positive feelings in the user as they interact with the interface. The use of interactive television (iTV) and affective usability illustrate how usability paradigms shift as new technology is developed. Traditional television is a more passive medium than iTV and the role of the user (or viewer) varies significantly. iTV requires more of the user and to be an active contributor because of the more interactive interaction style. Interface designers need to constantly define better ways of developing interfaces that are not only usable, but also enjoyable to use.

A novel method of tube manufacture for vehicle crashworthiness utilising the QUICKSTEP™ Process.

A novel method of composite tube manufacture was developed for potential use in automotive crash structures. Tubes were crushed axially under quasi-static conditions and highly repeatable behaviour was observed with an average specific energy absorption of -85kJ/kg. DMTA results indicated that the tubes were fully cured, even when the cycle was reduced to 7 minutes, giving this process huge potential for high-volume production.

Confirming the position of a nasogastric tube what does the literature say?

Nasogastric tubes are a medical device that can be used for a number of purposes. The process of inserting them however can be complicated. Nurses must therefore use an evidence based approach to confirm the correct position of nasogastric tubes and there are three main techniques described in the literature to do so. To date, one group of authors has published the majority of the studies on these techniques. This paper reviews their work.

Substitution reactions of carbon nanotube template

Substitution reactions between carbon nanotube (CNT) template and SiO with the formation of carbon rich silicon oxide nanowires (SiO–C-NWs) have been investigated using transmission electron microscopy and x-ray energy dispersive spectroscopy. The reaction was carried out by thermal annealing at 1200 °C for 1 h of a mixture of silicon monoxide (SiO) and iron (II) phthalocyanine, FeC32N8H16 (FePc) powders. Multiwalled CNTs were produced first via pyrolysis of FePc at a lower temperature (1000 °C). SiO vapors reacted with the CNTs at higher temperatures to produce amorphous SiO–C-NWs with a uniform diameter and a length in tens of micrometers. The special bamboolike structure of the CNTs allows the reaction to start from the external surface of the tubes and transform each CNT into a solid nanowire section by section.

Carbon nanotubes formed in graphite after mechanical grinding and thermal annealing

Multi-walled carbon nanotubes with cylindrical and bamboo-type structures are produced in a graphite sample after mechanical milling at ambient temperature and subsequent thermal annealing up to 1400 °C. The ball milling produces a precursor structure and the thermal annealing activates the nanotube growth. Different nanotubular structures indicate different formation mechanisms: multi-wall cylindrical carbon nanotubes are probably formed upon micropores and the bamboo tubes are produced because of the metal catalysts. A two-dimensional growth governed by surface diffusion is believed to be one important factor for the nanotube growth. A potential industrial production method is demonstrated with advantages of large production quantity and low cost.

Influence of nitriding gases on the growth of boron nitride nanotubes

Boron nitride (BN) nanotubes of different sizes and tubular structures exhibit very different mechanical and chemical properties, as well as different applications. BN nanotubes of different sizes and nanostructures have been produced in different nitriding gases in a milling and annealing process, in which elemental boron powder was first milled in NH₃ for 150 h and subsequently annealed at 1,200 °C for 6 h. The influence of nitriding gases was investigated by using N₂, NH₃, N₂–H₂ mixture gases. A relatively slow nitriding reaction in NH₃ gas leaded to a 2D growth of BN (002) basal planes and the formation of thin BN nanotubes without the help of metal catalysts. Fast nitriding reactions occurred in N₂ or N₂–H₂ mixture gases, catalyzed by metal particles, resulted in 3D crystal growth and the formation of many large cylindrical and bamboo tubes.

Photodegradation, interaction with iron oxides and bioavailability of dissolved organic matter from forested floodplain sources

Photochemical degradation of dissolved organic matter (DOM) can influence food webs by altering the availability of carbon to microbial communities, and may be particularly important following periods of high DOM input (e.g. flooding of forested floodplains). Iron oxides can facilitate these reactions, but their influence on subsequent organic products is poorly understood. Degradation experiments with billabong (= oxbow lake) water and river red gum (Eucalyptus camaldulensis) leaf leachate were conducted to assess the importance of these reactions in floodplain systems. Photochemical degradation of DOM in sunlight-irradiated quartz tubes (with and without amorphous iron oxide) was studied using gas chromatography and UV-visible spectroscopy. Photochemical reactions generated gaseous products and small organic acids. Bioavailability of billabong DOM increased following irradiation, whereas that of leaf leachate was not significantly altered. Fluorescence excitation-emission spectra suggested that the humic component of billabong organic matter was particularly susceptible to degradation, and the source of DOM influenced the changes observed. The addition of amorphous iron oxide increased rates of photochemical degradation of leachate and billabong DOM. The importance of photochemical reactions to aquatic systems will depend on the source of the DOM and its starting bioavailability, whereas inputs of freshly formed iron oxides will accelerate the processes.