System for studies of control strategies applied in the refrigerated chambers

The process of cold storage chambers contributes largely to the quality and longevity of stored products. In recent years, it has been intensified the study of control strategies in order to decrease the temperature change inside the storage chamber and to reduce the electric power consumption. This study has developed a system for data acquisition and process control, in LabVIEW language, to be applied in the cooling system of a refrigerating chamber of 30m³. The use of instrumentation and the application developed fostered the development of scientific experiments, which aimed to study the dynamic behavior of the refrigeration system, compare the performance of control strategies and the heat engine, even due to the controlled temperature, or to the electricity consumption. This system tested the strategies for on-off control, PID and fuzzy. Regarding power consumption, the fuzzy controller showed the best result, saving 10% when compared with other tested strategies.

Nocturnal thermal comfort in facilities for growing swines

In most of Brazilian pig farms, the environmental acclimatization systems run manually. For night and early morning periods, this practice isn't appropriate, because, in general, there are not employees available to run these manual systems. This research aimed to compare the bioclimatic profile of two differently constructed facilities to the external environment, considering the period from 6 p.m. to 6 a.m. during the spring, in order to show that night and early morning temperatures do not coincides with growing pig's thermoneutral zone. For this reason, acclimatization must be also carried out at these periods. It was analyzed the dry bulb temperature, relative air humidity, temperature-humidity index (THI) and enthalpy data of the sheds and external areas. Under the studied conditions, it was possible to conclude that the constructively appropriate shed appeared to be less influenced by the external environment, allowing better thermal control for growing pigs. Further research must be conducted to verify if automatic cooling systems is needed during night and early morning.

Low cost driver device for microclimate maintenance in the pre-milking of dairy cattle

Due to the importance of the environment on animal production and thus environmental control, the study aims to build a system for monitoring and control the meteorological variables, temperature and relative humidity, low cost, which can be associated with an evaporative cooling system (ECS). The system development included all the stages of assembly, test and laboratory calibration, and later the validation of the equipment carried in the field. The validation step showed results which allowed concluding that the system can be safely used in the monitoring of these variables. The controller was efficient in management of the microclimate in the waiting corral and allowed the maintenance of the air temperature within the comfort range for dairy cattle in pre-milking with averaged 25.09 ºC during the afternoon. The equipment showed the lower cost (R$ 325.76) when compared to other middle market (R$ 450.00).

The Possibilities and Dosimetric Limitations of MLC-Based Intensity-Modulated Radiotherapy Delivery and Optimization Techniques

The use of intensity-modulated radiotherapy (IMRT) has increased extensively in the modern radiotherapy (RT) treatments over the past two decades. Radiation dose distributions can be delivered with higher conformality with IMRT when compared to the conventional 3D-conformal radiotherapy (3D-CRT). Higher conformality and target coverage increases the probability of tumour control and decreases the normal tissue complications. The primary goal of this work is to improve and evaluate the accuracy, efficiency and delivery techniques of RT treatments by using IMRT. This study evaluated the dosimetric limitations and possibilities of IMRT in small (treatments of head-and-neck, prostate and lung cancer) and large volumes (primitive neuroectodermal tumours). The dose coverage of target volumes and the sparing of critical organs were increased with IMRT when compared to 3D-CRT. The developed split field IMRT technique was found to be safe and accurate method in craniospinal irradiations. By using IMRT in simultaneous integrated boosting of biologically defined target volumes of localized prostate cancer high doses were achievable with only small increase in the treatment complexity. Biological plan optimization increased the probability of uncomplicated control on average by 28% when compared to standard IMRT delivery. Unfortunately IMRT carries also some drawbacks. In IMRT the beam modulation is realized by splitting a large radiation field to small apertures. The smaller the beam apertures are the larger the rebuild-up and rebuild-down effects are at the tissue interfaces. The limitations to use IMRT with small apertures in the treatments of small lung tumours were investigated with dosimetric film measurements. The results confirmed that the peripheral doses of the small lung tumours were decreased as the effective field size was decreased. The studied calculation algorithms were not able to model the dose deficiency of the tumours accurately. The use of small sliding window apertures of 2 mm and 4 mm decreased the tumour peripheral dose by 6% when compared to 3D-CRT treatment plan. A direct aperture based optimization (DABO) technique was examined as a solution to decrease the treatment complexity. The DABO IMRT technique was able to achieve treatment plans equivalent with the conventional IMRT fluence based optimization techniques in the concave head-and-neck target volumes. With DABO the effective field sizes were increased and the number of MUs was reduced with a factor of two. The optimality of a treatment plan and the therapeutic ratio can be further enhanced by using dose painting based on regional radiosensitivities imaged with functional imaging methods.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

Spin-Dynamics in Cold Gases of 87Rb and Atomic Hydrogen. The spins they are a-changin’

In this thesis the dynamics of cold gaseous atoms is studied. Two different atomic species and two different experimental techniques have been used. In the first part of the thesis experiments with Bose-Einstein condensates of Rb-87 are presented. In these experiments the methods of laser cooling and magnetic trapping of atoms were utilized. An atom chip was used as the experimental technique for implementation of magnetic trapping. The atom chip is a small integrated instrument allowing accurate and detailed manipulation of the atoms. The experiments with Rb-87 probed the behaviour of a falling beam of atoms outcoupled from the Bose-Einstein condensate by electromagnetic field induced spin flips. In the experiments a correspondence between the phases of the outcoupling radio frequency field and the falling beam of atoms was found. In the second part of the thesis experiments of spin dynamics in cold atomic hydrogen gas are discussed. The experiments with atomic hydrogen are conducted in a cryostat using a dilution refrigerator as the cooling method. These experiments concentrated on explaining and quantifying modulations in the electron spin resonance spectra of doubly polarized atomic hydrogen. The modifications to the previous experimental setup are described and the observation of electron spin waves is presented. The observed spin wave modes were caused by the identical spin rotation effect. These modes have a strong dependence on the spatial profile of the polarizing magnetic field. We also demonstrated confinement of these modes in regions of strong magnetic field and manipulated their spatial distribution by changing the position of the field maximum.

Suurnopeus-turbokoneroottoreiden termodynaaminen ja mekaaninen mallinnus sekä rakenneanalyysi

Tässä väitöskirjassa tarkastellaan suurnopeustekniikan eri sovelluksissa ilmeneviä roottoreihin liittyviä rakenteellisia vaatimuksia ja haasteita. Tässä yhteydessä suurnopeustekniikalla tarkoitetaan järjestelyä, jossa sähkökone (moottori, generaattori) ja toimilaite (turbiini, kompressori, puhallin) on kytketty ilman vaihdetta suoraan mekaanisesti yhteen ja jossa yhteisen roottorin pyörimisnopeus on selvästi suurempi kuin 50/60 hertsin verkosta syötetyn kaksinapaisen vaihtovirtasähkökoneen tahtinopeus. Tyypillistä suurnopeuskoneen roottorille on suuri tehotiheys ja suuri mekaaninen kuormitus. Siksi esimerkiksi sähkökoneen jäähdytys on entistä haasteellisempaa kasvavien rautahäviöiden ja pienempien lämmönsiirtopinta-alojen vuoksi. Tämän työn tavoitteet voidaan jakaa kolmeen osaan:  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen tarkastelu, jonka tavoitteena on pienentää lämmönkehitystä ja tehostaa kriittisten kohtien jäähdytystä. Tähän liittyy sähkömagneettisten häviöiden keskittäminen jäähdytyksen kannalta edullisiin kohtiin  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen tarkastelu kriittisten ominaistaajuuksien kannalta  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen analysointi lujuustekniseltä kannalta. Tähän liittyvät mm. erilaiset ahdistussovitteet ja niiden säilyminen korkeilla pyörimisnopeuksilla sekä niiden roottoria jäykistävä vaikutus ja lämmön johtuminen kyseisissä liitospinnoissa. Tämän työn tieteellinen uutuusarvo on nimenomaan yhdistetyn sähkö- ja turbokoneen roottorin rakenteen analysointi ottamalla samanaikaisesti huomioon kaikki edellä mainitut näkökohdat: jäähtyminen erityisen kuumissa kohdissa, sähköisten häviöiden alentaminen ja niiden jakautuman huomioon ottaminen, roottorin jäykkyyden maksimointi, lujuusrasitusten hallinta ja rakenteen mekaaninen stabiliteetti sekä lämpöteknisten ylimenovastusten tarkastelu.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

Cysteine addition on short-term cooled boar semen preservation and its relationship with swine field fertility

Artificial insemination is routinely used in the swine industry to reduce the costs of production through to increase the efficiency of the refrigerated boar semen process. The objective of this study was to evaluate the effect of different levels of cysteine (CYS) added to the Beltsville Thawing Solution (BTS) extender semen during cooling for up to 72 hours. Ejaculated from three boars were collected with the gloved-hand technique and semen aliquots were diluted in BTS as follow: BTS only (BTS), BTS + 0.1mM cysteine (CYS0.1), BTS + 0.5mM cysteine (CYS0.5), BTS + 1.0mM cysteine (CYS1.0), BTS + 2.5mM cysteine (CYS2.5), BTS + 5.0mM cysteine (CYS5.0), BTS + 10.0mM cysteine (CYS10.0), and BTS + 20.0mM cysteine (CYS20.0). Evaluation of sperm integrity were analyzed using 0.5mg/ml propidium iodide (plasma membrane), 100µg/ml isothiocynate-conjugated Pisum sativun agglutinin (acrosomal membrane) and 153µM 5,5',6,6'-tetrachloro-1,1',3,3'-tetraethylbenzimidazolyl carbocyanine iodide (mitochondria potential) after semen dilution at specific times (0, 24, 48 and 72 hours). Additionally, we also evaluated the effects of 5.0 mM CYS addition in the BTS extender on the maintenance of sperm quality and their influence on fertility in the swine production. After artificial insemination, animals were evaluated based on the estrous return and the number of piglet's born. Cysteine at concentrations of 10.0 and 20.0mM resulted in more pronounced reductions even at the time zero. Semen viability decreased to levels below 10% at these high levels of CYS in the first 24 hour of storage at 17ºC. At the end of the storage time, less than 65% of sperm cells had intact plasma membrane in all groups. The sperm viability decreased significantly when the semen was added at high concentrations of CYS (time "0"; CYS10.0 and CYS20.0; p<0.05), when compared to the other CYS concentrations. The BTS (10.20±0.39) treated group showed a lower rate of estrus return when compared to other (BTSCYS; 86.05±039), and it showed also the highest total number of piglets borne per treatment (12.71±3.38 vs. 9.00±3.38, respectively). In conclusion, the addition of CYS in the BTS semen extender did not maintain spermatic viability of boar cooled spermatozoa and it results in a higher percentage of return to estrus and lower number of piglets borne.

Hyperbolic type metrics and distortion of quasiconformal map pings

This Ph.D. thesis consists of four original papers. The papers cover several topics from geometric function theory, more specifically, hyperbolic type metrics, conformal invariants, and the distortion properties of quasiconformal mappings. The first paper deals mostly with the quasihyperbolic metric. The main result gives the optimal bilipschitz constant with respect to the quasihyperbolic metric for the M¨obius self-mappings of the unit ball. A quasiinvariance property, sharp in a local sense, of the quasihyperbolic metric under quasiconformal mappings is also proved. The second paper studies some distortion estimates for the class of quasiconformal self-mappings fixing the boundary values of the unit ball or convex domains. The distortion is measured by the hyperbolic metric or hyperbolic type metrics. The results provide explicit, asymptotically sharp inequalities when the maximal dilatation of quasiconformal mappings tends to 1. These explicit estimates involve special functions which have a crucial role in this study. In the third paper, we investigate the notion of the quasihyperbolic volume and find the growth estimates for the quasihyperbolic volume of balls in a domain in terms of the radius. It turns out that in the case of domains with Ahlfors regular boundaries, the rate of growth depends not merely on the radius but also on the metric structure of the boundary. The topic of the fourth paper is complete elliptic integrals and inequalities. We derive some functional inequalities and elementary estimates for these special functions. As applications, some functional inequalities and the growth of the exterior modulus of a rectangle are studied.

The effects of welding heat input on the usability of high strength steels in welded structures

High strength steel (HSS) has been in use in workshops since the 1980s. At that time, the significance of the term HSS differed from the modern conception as the maximum yield strength of HSSs has increased nearly every year. There are three different ways to make HSS. The first and oldest method is QT (quenched and tempered) followed by the TMCP (thermomechanical controlled process) and DQ (direct quenching) methods. This thesis consists of two parts, the first of which part introduces the research topic and discusses welded HSS structures by characterizing the most important variables. In the second part of the thesis, the usability of welded HSS structures is examined through a set of laboratory tests. The results of this study explain the differences in the usability of the welded HSSs made by the three different methods. The results additionally indicate that usage of different HSSs in the welded structures presumes that manufacturers know what kind of HSS they are welding. As manufacturers use greater strength HSSs in welded structures, the demands for welding rise as well. Therefore, during the manufacturing process, factors such as heat input, cooling time, weld quality, and more must be under careful observation.

Eri MAG-hitsausprosessien ja -parametrien vaikutus suurlujuusteräksestä valmistetun otsapienahitsin äärikestävyyteen, muodonmuutoskykyyn ja vauriomuotoon

Työssä tutkittiin Ruukki Oyj:n suorasammutetusta S960QC-teräksestä valmistetun kuormaakantavan levyjen ristiliitoksen pienahitsien lujuutta, muodonmuutoskykyä ja vaurioitumismekanismia laajaan kokeelliseen aineistoon perustuen. Tärkeimpänä muuttujana koematriisissa olivat eri MAG-hitsausprosessit. Perinteisen kuumakaarihitsauksen vertailukohteena oli Kemppi Oy:n uusi adaptiivinen valokaaren pituutta säätävä WiseFusion-hitsaustoiminto kuuma- ja pulssikaarihitsauksessa. Näiden kolmen hitsausprosessin rinnalla varioitiin erisuuruisia a-mittoja, eri hitsauslisäaineita ja hitsin erikylkisyyttä. Lisäksi juuritunkeuman estämisen vaikutusta hitsien käyttäytymiseen tutkittiin täydentävällä koesarjalla, jossa tunkeuman muodostuminen estettiin levyjen väliin asetetulla volframilevyllä. Työn perimmäisenä tavoitteena oli selvittää syy aiemmassa tutkimuksessa havaitulle pienahitsien vaurioitumiselle leikkautumalla sularajaa pitkin. Sularajan suhteellista pituutta saadaan kasvatettua estämällä hitsin juuritunkeuma ja absoluuttista pituutta saadaan lisää kateettipoikkeaman avulla. Lisäksi tutkimuksessa oli tarkoitus tuoda esille suurlujuusteräksisen liitoksen eri mitoituslähtökohdat (mm. lämmöntuonnin kontrollointi). Tämän vuoksi hitsausparametrit mitattiin jännitteen ja virran hetkellisiin arvoihin perustuen, jolloin kuuma- ja pulssikaarihitsauksen laskennalliset hitsaustehot ovat vertailukelpoisia. Koehitseistä valmistettiin hieet hitsien tarkan geometrian määrittämiseksi ja liitoksen mekaaniset ominaisuudet tutkittiin vetokokeella. Tulosten perusteella sularajavaurio aktivoituu pulssikaarella hitsatuissa koekappaleissa. Tämä aiheutunee pulssi- ja kuumakaarihitsauksen sularajan mikrorakenteiden eroavaisuudesta. Sularajavaurio näyttää huonontavan hitsien muodonmuutoskykyä, mutta jatkokokeita tuloksen verifioimiseksi on tehtävä. S960QC-teräkselle ominaisen pehmenneen vyöhykkeen vaurio ei aktivoitunut, vaikka Ruukin antamat jäähtymisaikasuositukset ylitettiin reilusti.

Effects of environmental modification on mastitis occurrence and hormonal changes in Holstein cows

The purpose of this research was to evaluate the effects of evaporative cooling in freestall on mastitis occurrence, milk production, and composition, as well as cortisol, T3 (triiodothyronine), and T4 (thyroxin) levels in lactating dairy cows. Twenty-eight multiparous cows averaging 70 ± 10 day postpartum were used in four treatments from January to March 2003. The treatments were: Day (cooling from 7:00 a.m. to 7:00 p.m.); Night (cooling from 7:00 p.m. to 7:00 a.m.); 24-hour (cooling 24-hour); and Control (no cooling). Wired cup test was used for clinical mastitis diagnosis, and the California Mastitis Test (CMT) was used to identify subclinical mastitis. Blood and milk samples were taken weekly for microbiological and hormonal analyses. The cortisol levels were higher than normal values in all treatment groups, suggesting stress conditions, but T3 and T4 levels remained normal in all groups. The occurrence of subclinical mastitis was lower in Day and Night groups than in Control and 24-hour groups. Regarding the microbiological analyses, in all groups the isolation of Corynebacterium sp. from milk samples increased while negative coagulase staphylococci (CNS) declined as etiological agents of subclinical mastitis. However, in Day and 24-hour groups, coagulase positive staphylococci (CPS) increased mainly Staphylococcus aureus (49.8% and 47.7% respectively). The Night group showed a decrease in subclinical mastitis occurrences. Our data indicate that all animals subjected to treatments presented high levels of cortisol, indicating a stress condition. The Night treatment presented a reduction in microbial isolation, suggesting a reduced susceptibility to mastitis.

Matalalämpötilaisen hukkalämmön hyödyntäminen kaukolämmön tuotannossa

Työ käsittelee tekniikoita, joilla voidaan hyödyntää matalalämpötilaisia hukkalämpöjä kaukolämmöntuotannossa. Työ esittelee lämpöpumpputekniikkaa, jolla hukkalämmön lähteestä tulevaa lämpöä voidaan lämpötilaltaan nostaa kaukolämpöverkon tarpeita vastaavaksi. Työssä käsitellään lämpöpumppujen kylmäaineita ja niiden soveltuvuutta eri lämpötila-alueisiin. Lisäksi käsitellään hyödyntämisen taloudellisuutta ja ympäristövaikutuksia. Taloudellisuudessa käsitellään investointi- ja käyttökustannukset ja pohditaan niiden pohjalta tuotteiden kaukolämpö- ja kaukokylmähinnoittelua asiakkaille. Työ myös tarkastelee hankkeen kokonaiskannattavuutta Mäntsälän Sähkölle. Kannattavuuslaskelmissa toteutetaan herkkyystarkastelu suurimpien muuttujien osalta. Työ tarkastelee yhdistetyn kylmän- ja lämmöntuotannon soveltuvuutta Mäntsälän keskustan kaukolämpöverkon ja Kapulin kaukolämpöverkon alueelle. Soveltuvuutta tarkastellaan Suomessa ja maailmalla toteutettujen referenssien pohjalta.