Effect of cooling rate on intercritically reheated microstructure and toughness in high strength low alloy steel

High strength low alloy steels have been shown to be adversely affected by the existence of regions of poor impact toughness within the heat affected zone (HAZ) produced during multipass welding. One of these regions is the intercritically reheated coarse grained HAZ or intercritical zone. Since this region is generally narrow and discontinuous, of the order of 0.5 mm in width, weld simulators are often employed to produce a larger volume of uniform microstructure suitable for toughness assessment. The steel usedfor this study was a commercial quenched and tempered steel of 450 MN m -2 yield strength. Specimen blanks were subjected to a simulated welding cycle to produce a coarse grained structure of upper bainite during the first thermal cycle, followed by a second thermal cycle where the peak temperature T p2 was controlled. Charpy tests carried out for T p2 values in the range 650-850°C showed low toughness for T p2 values between 760 and 790°C, in the intercritical regime. Microstructural investigation of the development of grain boundary martensite-retained austenite (MA) phase has been coupled with image analysis to measure the volume fraction of MAformed. Most of the MA constituent appears at the prior austenite grain boundaries during intercritical heating, resulting in a 'necklace' appearance. For values of T p2 greater than 790°C the necklace appearance is lost and the second phase areas are observed throughout the structure. Concurrent with this is the development of the fine grained, predominantly ferritic structure that is associated with the improvement in toughness. At this stage the microstructure is transforming from the intercritical regime structure to the supercritically reheated coarse grained HAZ structure. The toughness improvement occurs even though the MA phase is still present, suggesting that the embrittlement is associated with the presence of a connected grain boundary network of the MA phase. The nature of the second phase particles can be controlled by the cooling rate during the second cycle and variesfrom MA phase at high cooling rates to a pearlitic structure at low cooling rates. The lowest toughness of the intercritical zone is observed only when MA phase is present. The reason suggested for this is that only the MA particles debond readily, a number of debonded particles in close proximity providing sufficient stress concentration to initiate local cleavage. © 1993 The Institute of Materials.

Climate change performance measurement, control and accountability in English local areas

Purpose – This paper aims to consider how climate change performance is measured and accounted for within the performance framework for local authority areas in England adopted in 2008. It critically evaluates the design of two mitigation and one adaptation indicators that are most relevant to climate change. Further, the potential for these performance indicators to contribute to climate change mitigation and adaptation is discussed. Design/methodology/approach – The authors begin by examining the importance of the performance framework and the related Local Area Agreements (LAAs), which were negotiated for all local areas in England between central government and Local Strategic Partnerships (LSPs). This development is located within the broader literature relating to new public management. The potential for this framework to assist in delivering the UK's climate change policy objectives is researched in a two-stage process. First, government publications and all 150 LAAs were analysed to identify the level of priority given to the climate change indicators. Second, interviews were conducted in spring 2009 with civil servants and local authority officials from the English West Midlands who were engaged in negotiating the climate change content of the LAAs. Findings – Nationally, the authors find that 97 per cent of LAAs included at least one climate change indicator as a priority. The indicators themselves, however, are perceived to be problematic – in terms of appropriateness, accuracy and timeliness. In addition, concerns were identified about the level of local control over the drivers of climate change performance and, therefore, a question is raised as to how LSPs can be held accountable for this. On a more positive note, for those concerned about climate change, the authors do find evidence that the inclusion of these indicators within the performance framework has helped to move climate change up the agenda for local authorities and their partners. However, actions by the UK's new coalition government to abolish the national performance framework and substantially reduce public expenditure potentially threaten this advance. Originality/value – This paper offers an insight into a new development for measuring climate change performance at a local level, which is relatively under-researched. It also contributes to knowledge of accountability within a local government setting and provides a reference point for further research into the potential role of local actions to address the issue of climate change.

Power industry restructuring and eco-efficiency changes:a new slacks-based model in Malmquist-Luenberger Index measurement

Measuring variations in efficiency and its extension, eco-efficiency, during a restructuring period in different industries has always been a point of interest for regulators and policy makers. This paper assesses the impacts of restructuring of procurement in the Iranian power industry on the performance of power plants. We introduce a new slacks-based model for Malmquist-Luenberger (ML) Index measurement and apply it to the power plants to calculate the efficiency, eco-efficiency, and technological changes over the 8-year period (2003-2010) of restructuring in the power industry. The results reveal that although the restructuring had different effects on the individual power plants, the overall growth in the eco-efficiency of the sector was mainly due to advances in pure technology. We also assess the correlation between efficiency and eco-efficiency of the power plants, which indicates a close relationship between these two steps, thus lending support to the incorporation of environmental factors in efficiency analysis. © 2014 Elsevier Ltd.

Modernising local government:a role for parish and town councils

Recent initiatives for modernising local government have ignored the potential contribution of parish and town councils. This article critically examines English parish and town councils in the context of the current debate about the need for government to be more responsive to community needs. It considers measures to enhance the capacity of these grassroots councils by recalibrating the responsibilities and resources between tiers of local government. It concludes by setting out possible reforms to facilitate the contribution of these local councils to the modernising agenda as both representatives of the community and potential providers of local services.

Electrografting of poly (carbazole-co-acrylamide) onto highly oriented pyroltic graphite. A cyclovoltammetric, atomic force microscopic and ellipsometric study

The electrocopolymerization of carbazole and acrylamide on highly oriented pyrolytic graphite (HOPG) from ACN solutions via cyclovoltammetry (CV) was studied in order to evaluate the possibility to deposit uniform and thin but pinhole-free and still reactive coatings onto graphite-like substrates. The morphology of the coatings was investigated using atomic force microscopy and the coating thicknesses and optical parameters were measured using ellipsometry. It was found that under the chosen conditions thin (coating thickness hf>180 nm) and relatively smooth (root mean square surface roughness RMS<150 nm) P(Cz-co-AAm)-coatings exhibiting a uniform globuoidal morphology can be deposited onto graphite. From a certain coating thickness (hf>50 nm) no pinholes could be detected. It was found that the thickness of the deposited coatings increases almost linearly with increasing number of CV-cycles while keeping all other experimental parameters (scan rate and comonomer concentration ratio) constant. No influence of the comonomer concentration ratio on the film thickness and coating appearance could be observed, however, at quite low initial concentrations. However, the CV-scanning rate has quite a significant influence on the thickness of the deposited coatings. Higher scan rates (100 mV/s) result in thin (hf≈22 nm) coatings whereas at lower scan rates (<50 mV/s) coatings with thicknesses of approximately 50 nm were obtained. The optical coating parameters (the refractive index n and extinction coefficient k) seem to be independent of the deposition parameters and therefore averaged values of n̄=1.54±0.03 and k̄=0.08±0.03 were obtained.

A statistical analysis of regional variation in adverb position in a corpus of written Standard American English

This paper investigates whether the position of adverb phrases in sentences is regionally patterned in written Standard American English, based on an analysis of a 25 million word corpus of letters to the editor representing the language of 200 cities from across the United States. Seven measures of adverb position were tested for regional patterns using the global spatial autocorrelation statistic Moran’s I and the local spatial autocorrelation statistic Getis-Ord Gi*. Three of these seven measures were indentified as exhibiting significant levels of spatial autocorrelation, contrasting the language of the Northeast with language of the Southeast and the South Central states. These results demonstrate that continuous regional grammatical variation exists in American English and that regional linguistic variation exists in written Standard English.

Hybrid tilted fiber grating based refractive index and liquid level sensing system

We report a refractive index (RI) and liquid level sensing system based on a hybrid grating structure comprising of a 45° and an 81° tilted fiber gratings (TFGs) that have been inscribed into a single mode fiber in series. In this structure, the 45°-TFG is used as a polarizer to filter out the transverse electric (TE) component and enable the 81°-TFG operating at single polarization for RI and level sensing. The experiment results show a lower temperature cross-sensitivity, only about 7.33 pm/°C, and a higher RI sensitivity, being around 180 nm/RIU at RI=1.345 and 926 nm/RIU at RI=1.412 region, which are significantly improved in comparison with long period fiber gratings. The hybrid grating structure has also been applied as a liquid level sensor, showing 3.06 dB/mm linear peak ratio sensitivity.

Simultaneous measurement of refractive index and temperature using multimode microfiber-based dual Mach-Zehnder interferometer

A multimode microfiber (MMMF)-based dual Mach-Zehnder interferometer (MZI) is proposed and demonstrated for simultaneous measurement of refractive index (RI) and temperature. By inserting a section of MMMFsupporting a few modes in the sensing arm of the MZI setup, an inline interference between the fundamental mode and the high-order mode of MMMF, as well as the interference between the high-order mode of MMMF and the reference arm, i.e., the dual MZI, is realized. Due to different interference mechanisms, the former interferometer achieves RI sensitivity of 2576.584 nm/RIU and temperature sensitivity of 0.193 nm/°C, while the latter one achieves RI sensitivity of 1001.864 nm/RIU and temperature sensitivity of 0.239 nm/°C, demonstrating the ability to attain highly accurate multiparameter measurements. © 2014 Optical Society of America.

High-Order Control Variations and Small-Time Local Controllability

The importance of “control variations” for obtaining local approximations of the reachable set of nonlinear control systems is well known. Heuristically, if one can construct control variations in all possible directions, then the considered control system is small-time locally controllable (STLC). Two concepts of control variations of higher order are introduced for the case of smooth control systems. The relation between these variations and the small-time local controllability is studied and a new sufficient STLC condition is proved.

A comparison of two distributed large-volume measurement systems:the mobile spatial co-ordinate measuring system and the indoor global positioning system

Advances in the area of industrial metrology have generated new technologies that are capable of measuring components with complex geometry and large dimensions. However, no standard or best-practice guides are available for the majority of such systems. Therefore, these new systems require appropriate testing and verification in order for the users to understand their full potential prior to their deployment in a real manufacturing environment. This is a crucial stage, especially when more than one system can be used for a specific measurement task. In this paper, two relatively new large-volume measurement systems, the mobile spatial co-ordinate measuring system (MScMS) and the indoor global positioning system (iGPS), are reviewed. These two systems utilize different technologies: the MScMS is based on ultrasound and radiofrequency signal transmission and the iGPS uses laser technology. Both systems have components with small dimensions that are distributed around the measuring area to form a network of sensors allowing rapid dimensional measurements to be performed in relation to large-size objects, with typical dimensions of several decametres. The portability, reconfigurability, and ease of installation make these systems attractive for many industries that manufacture large-scale products. In this paper, the major technical aspects of the two systems are briefly described and compared. Initial results of the tests performed to establish the repeatability and reproducibility of these systems are also presented. © IMechE 2009.

Refractive index and temperature sensitivity characteristics of a micro-slot fiber Bragg grating

Fabrication and characterization of a UVinscribed fiber Bragg grating (FBG) with a micro-slot liquid core is presented. Femtosecond (fs) laser patterning/chemical etching technique was employed to engrave a micro-slot with dimensions of 5.74 μm(h) × 125 μm(w) × 1388.72 μm(l) across the whole grating. The device has been evaluated for refractive index (RI) and temperature sensitivities and exhibited distinctive thermal response and RI sensitivity beyond the detection limit of reported fiber gratings. This structure has not just been RI sensitive, but also maintained the robustness comparing with the bare core FBGs and long-period gratings with the partial cladding etched off. © 2012 Optical Society of America.

Estimation of average annual daily traffic (AADT) using geographically weighted regression (GWR) method and geographic information system (GIS)

Annual average daily traffic (AADT) is important information for many transportation planning, design, operation, and maintenance activities, as well as for the allocation of highway funds. Many studies have attempted AADT estimation using factor approach, regression analysis, time series, and artificial neural networks. However, these methods are unable to account for spatially variable influence of independent variables on the dependent variable even though it is well known that to many transportation problems, including AADT estimation, spatial context is important. ^ In this study, applications of geographically weighted regression (GWR) methods to estimating AADT were investigated. The GWR based methods considered the influence of correlations among the variables over space and the spatially non-stationarity of the variables. A GWR model allows different relationships between the dependent and independent variables to exist at different points in space. In other words, model parameters vary from location to location and the locally linear regression parameters at a point are affected more by observations near that point than observations further away. ^ The study area was Broward County, Florida. Broward County lies on the Atlantic coast between Palm Beach and Miami-Dade counties. In this study, a total of 67 variables were considered as potential AADT predictors, and six variables (lanes, speed, regional accessibility, direct access, density of roadway length, and density of seasonal household) were selected to develop the models. ^ To investigate the predictive powers of various AADT predictors over the space, the statistics including local r-square, local parameter estimates, and local errors were examined and mapped. The local variations in relationships among parameters were investigated, measured, and mapped to assess the usefulness of GWR methods. ^ The results indicated that the GWR models were able to better explain the variation in the data and to predict AADT with smaller errors than the ordinary linear regression models for the same dataset. Additionally, GWR was able to model the spatial non-stationarity in the data, i.e., the spatially varying relationship between AADT and predictors, which cannot be modeled in ordinary linear regression. ^

Development and testing of the Elderly Social Vulnerability Index (ESVI): A composite indicator to measure social vulnerability in the Jamaican elderly population

Over the last two decades social vulnerability has emerged as a major area of study, with increasing attention to the study of vulnerable populations. Generally, the elderly are among the most vulnerable members of any society, and widespread population aging has led to greater focus on elderly vulnerability. However, the absence of a valid and practical measure constrains the ability of policy-makers to address this issue in a comprehensive way. This study developed a composite indicator, The Elderly Social Vulnerability Index (ESVI), and used it to undertake a comparative analysis of the availability of support for elderly Jamaicans based on their access to human, material and social resources. The results of the ESVI indicated that while the elderly are more vulnerable overall, certain segments of the population appear to be at greater risk. Females had consistently lower scores than males, and the oldest-old had the highest scores of all groups of older persons. Vulnerability scores also varied according to place of residence, with more rural parishes having higher scores than their urban counterparts. These findings support the political economy framework which locates disadvantage in old age within political and ideological structures. The findings also point to the pervasiveness and persistence of gender inequality as argued by feminist theories of aging. Based on the results of the study it is clear that there is a need for policies that target specific population segments, in addition to universal policies that could make the experience of old age less challenging for the majority of older persons. Overall, the ESVI has displayed usefulness as a tool for theoretical analysis and demonstrated its potential as a policy instrument to assist decision-makers in determining where to target their efforts as they seek to address the issue of social vulnerability in old age. Data for this study came from the 2001 population and housing census of Jamaica, with multiple imputation for missing data. The index was derived from the linear aggregation of three equally weighted domains, comprised of eleven unweighted indicators which were normalized using z-scores. Indicators were selected based on theoretical relevance and data availability.

Life history trade-offs and community dynamics of small fishes in a seasonally pulsed wetland

We used a one-dimensional, spatially explicit model to simulate the community of small fishes in the freshwater wetlands of southern Florida, USA. The seasonality of rainfall in these wetlands causes annual fluctuations in the amount of flooded area. We modeled fish populations that differed from each other only in efficiency of resource utilization and dispersal ability. The simulations showed that these trade-offs, along with the spatial and temporal variability of the environment, allow coexistence of several species competing exploitatively for a common resource type. This mechanism, while sharing some characteristics with other mechanisms proposed for coexistence of competing species, is novel in detail. Simulated fish densities resembled patterns observed in Everglades empirical data. Cells with hydroperiods less than 6 months accumulated negligible fish biomass. One unique model result was that, when multiple species coexisted, it was possible for one of the coexisting species to have both lower local resource utilization efficiency and lower dispersal ability than one of the other species. This counterintuitive result is a consequence of stronger effects of other competitors on the superior species.