Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour

Desenvolvimento de membranas porosas de alumina para fins de tratamento de efluente industrial têxtil

Textile production has been considered as an activity of high environmental impact due to the generation of large volumes of waste water with high load of organic compounds and strongly colored effluents, toxic and difficult biodegradability. This thesis deals with obtaining porous alumina ceramic membranes for filtration of textile effluent in the removal of contaminants, mainly color and turbidity. Two types of alumina with different particle sizes as a basis for the preparation of formulation for mass production of ceramic samples and membranes. The technological properties of the samples were evaluated after using sintering conditions: 1,350ºC-2H, 1,450ºC-30M, 1,450ºC-2H, 1,475ºC-30M and 1,475ºC-2H. The sintered samples were characterized by XRD, XRF, AG, TG, DSC, DL, AA, MEA, RL, MRF-3P, SEM and Intrusion Porosimetry by Mercury. After the characterization, a standard membrane was selected with their respective sintering condition for the filterability tests. The effluent was provided by a local Textile Industry and characterized at the entry and exit of the treatment plant. A statistical analysis was used to study the effluent using the following parameters: pH, temperature, EC, SS, SD, oil and grease, turbidity, COD, DO, total phosphorus, chlorides, phenols, metals and fecal coliform. The filtered effluent was evaluated by using the same parameters. These results demonstrate that the feasibility of the use of porous alumina ceramic membranes for removing contaminants from textile effluent with improved average pore size of 0.4 micrometre (distribution range varying from 0,025 to 2.0 micrometre), with total porosity of 29.66%, and average percentages of color removal efficiency of 89.02%, 92.49% of SS, turbidity of 94.55%, metals 2.70% (manganese) to 71.52% (iron) according to each metal and COD removal of 72.80%

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Estudo de Matérias-Primas do Rio Grande do Norte para Uso em Revestimento Poroso: Influência do teor de dolomita e temperatura de calcinação nas propriedades físico-mecânicas

The state of Rio Grande do Norte presents a great potentiality for the production of ceramic tiles because of having natural raw material in quantity and quality making its economical exploration possible, beyond the great energetic differential of the state, the natural gás. This works aims to study the influence of the dolomite and granulometry concentration and calcinations temperature in the obtaining of formulations for porous coverings which have to be coherent to the project,s specifications. The experiments have involved the physical-chemical and mineralogical characterizations of raw materials and mechanical tests in the dry and burnt proof bodies preceding a mixture experiment planning with the use of the response surface methodology, in order to get the best raw materials combinations to produce a ceramic mass with specific properties. The twelve ceramic masses studied in this work were prepared by the via dry process, characterized, shaped by uniaxial pressing and sinterized in the temperatures of 940ºC, 1000ºC, 1060ºC, 1120ºC and 1180ºC, using a fast burning cycle. The crystalline phases formed during the sintering in the temperatures in study have revealed the presence of anorthite and diopside beyond quartz with a remaining phase. These phases were the main responsible ones by the physical- mechanical properties of the sinterized proof bodies. The proof bodies after the sintering stage have presented water absorption higher than 10% and a good dimensional stability in all studied temperatures. However, the flexural breaking strength results in the temperatures of 940ºC, 1000ºC and 1060ºC, under the temperature zone of the vitrification of ceramic whiteware do not reach the flexural breaking strength specific for the porous wall tile (15 MPa), but in the temperature of 1120ºC next to the vitrification temperature zone, some whiteware ceramic (formulations) has reached the specified value for the porous wall tile. The results of this work have showed that the studied raw materials have great importance for used in the production of porous wall tiles (BIII)

Aproveitamento de resíduo de beneficiamento do caulim na produção de porcelanato cerâmico

Nowadays, industries from all sectors have great concerns over the disposition of the residues generated along the productive process. This is not different in the mineral sector, as this generates great volumes of residues. It was verified that the kaolin improvement industry generates great volumes of residue basically constituted of kaolinite, muscovite mica and quartz, which are basic constitution elements to formularisations of ceramics masses to the production of covering of stoneware tiles type. This happens because the methodology applied to the improvement process is still very rudimentary, what causes a very low yield, only ¼ from all the material volume that enters the improvement process, in the end, is marketable. The disposal of this residue, in a general way, causes a very big negative environmental impact, what has justified the researches efforts aiming to find a rational solution to this problem. In this way, the intention of this present work is the utilization of this residue in the manufacture of products to high quality ceramics covering, stoneware tiles in an industrial scale. For this purpose, the influence of the addition of the residue to a standard ceramics mass used by a ceramics sector company, already established in the market, with the intention of verifying the possibility of use of this residue as the mass complementary raw material and even the possible partial or total substitution of one of the components of the mass for the raw material in evidence will be studied. To the accomplishment of this work, the kaolin improvement residue generated by an industry of exploitation and improvement of kaolin, located in the region of Equador-RN, in the levels 1,2,4,8, 16 and 32% will be added to the standard mass already used for the production of stoneware tiles. The raw materials used, kaolin residue and the standard mass, were characterized through DRX, FRX, DTA, TGA and dilatometry. After the sintering of the bodies of test, tests of water absorption, apparent porosity, post burning linear retraction, apparent specific mass and flexural strength (3 point bending) were realized to determinate the technological properties of these materials. The results show the studied residue can be considered raw material of great potential to the industry of floor and ceramics covering of the stoneware tiles type

[Texto del convenio de colaboración suscrito entre Artesanías de Colombia S. A. y la asociación de productores de mimbre de Ibagué – ASPROMI].

32 documentos : ilustraciones, fotografías.

As representações da nas primeiras sociedades camponesas do Alentejo Central (Portugal)

O Alentejo Central é detentor de um dos mais importantes conjuntos megalíticos a nível europeu. Esta importância decorre não só do elevado número de monumentos megalíticos conservados, mas também do numeroso e variado espólio progressivamente recolhido que nos permite compreender, em parte, a forma como viviam estas sociedades. Os projetos de investigação realizados nas últimas décadas em torno de alguns núcleos megalíticos alentejanos permitiu, por um lado, proceder a uma revisão e medição da orientação das antas e, por outro, compreender melhor as suas diversas e originais manifestações artísticas que se encontram profundamente marcadas por um simbolismo associado aos astros. De fato, em termos gerais, existe algum consenso sobre o simbolismo existente em torno da escolha das orientações dos monumentos megalíticos (funerários e não funerários) marcadamente associados ao Sol e/ou à Lua, ou hipoteticamente, a outras constelações. Nesta comunicação apontam-se e caracterizam-se sucintamente algumas destas orientações e as representações gráficas em espólios (cerâmicas, placas de xisto…) mais significativas e exemplificativas da importância da LUZ, na vida e nas crenças religiosas destas primeiras sociedades camponesas.

Technological characterization of molded islamic pottery from Iberian Peninsula

The thesis examines the technical aspects of unglazed molded ceramics from Mértola, in the context of Islamic archaeology of the Iberian Peninsula (Almohad period, end of 12th and the beginning of 13th century). Ceramics of the time period under discussion (12th – 13th century) are understudied, including in what concern to shaping and firing of ceramic vessels, the origin of raw materials used in ceramics and glazes, and decoration methods such as slip painting and/or colored glazes. Moreover, the use of archaeometry tools is rare. Along with providing a general picture of molded ceramic production in Mértola, this work provides a new dimension to the discipline of Islamic ceramic studies by the analytical tool used and demonstrating the importance of archaeological ceramics of the western peripheries to the understanding the production of ceramics and the transmission of knowledge and cultural traditions within the Islamic caliphate. The chemical and mineralogical characterization of 12th/13th century Almohad unglazed molded ware from Mértola was accomplished through multi – analytical approach combining SEM, Powder/uXRD and LA-ICP-MS methods. In this paper unglazed and glazed samples were analyzed but the attention was given to unglazed specimens, while the glazed samples were used for the comparison with the previous group in order to determine possible similarities or dissimilarities, thus providing enough data to discuss about technical aspects and potential provenance; Resumo: A tese debruça-se sobre os aspetos técnicos de cerâmica de molde não-vidrada de Mértola, no contexto da arqueologia islâmica da Península Ibérica (período Almóada, final de XII e início do século XIII). A cerâmica do período em discussão (séculos XII-XIII) é pouco estudada inclusive no que concerne ao fabrico e à cozedura, à de fonte de matérias-primas, na pasta ou nos esmaltes e aos métodos de decoração, como pintura, presença de engobes ou esmaltes. Além disso, o uso de ferramentas de Arqueometria é raro. Para fornecer uma visão geral da produção de cerâmica moldada em Mértola, este trabalho oferece uma nova dimensão para a disciplina de cerâmica islâmicas pelas ferramentas analíticas utilizadas. Demonstrando a importância da cerâmica arqueológica da periferia ocidental para a compreensão da produção cerâmica e a transmissão de conhecimentos e tradições culturais no califado islâmico. A caracterização mineralógica e química das cerâmicas de molde e não-vidrada, Almóada, dos séculos XII-XIII de Mértola foi realizada através de uma abordagem multi-analítica que combina métodos de SEM-EDS, uXRD e LA-ICP-MS. Neste trabalho, as cerâmicas vidradas e não-vidradas foram analisadas conjuntamente, dando mais atenção aos espécimes não vidrados. As amostras de cerâmicas vidradas foram utilizados para a comparação com o grupo anterior, a fim de determinar as possíveis semelhanças ou diferenças, proporcionando, assim, dados suficientes para discutir os aspetos técnicos e o potencial de proveniência das cerâmicas não vidradas