Análise térmica e mecânica de um compósito de matriz cerâmica com carga de EPS e raspa de pneu para construção de casas populares

Space Science was built using a composite made of plaster, EPS, shredded tires, cement and water. Studies were conducted to thermal and mechanical resistance. Inside the mold EPS plates were placed in order to obtain a higher thermal resistance on the wall constructed, as well as to give it an end environmentally friendly in view of both the tire and the EPS occupy a large space in landfills and year need to be degraded when released into the environment. Compression tests were performed according to ABNT blocks to seal, measurements of the temperature variation in the external and internal walls using a laser thermometer and check the temperature of the indoor environment using a thermocouple attached to a digital thermometer. The experiments demonstrated the heat provided by the composite values from the temperature difference between the internal and external surfaces on the walls, reaching levels of 12.4 ° C and room temperature in the interior space of the Science of 33.3 ° C, remaining within the zone thermal comfort for hot climate countries. It was also demonstrated the proper mechanical strength of such a composite for sealing walls. The proposed use of the composite can contribute to reducing the extreme housing shortage in our country, producing popular homes at low cost and with little time to work

Análise da lubricidade do biodiesel brasileiro de ésteres etílicos de soja e girassol

Fuel is a material used to produce heat or power by burning, and lubricity is the capacity for reducing friction. The aim of this work is evaluate the lubricity of eight fossil and renewable fuels used in Diesel engines, by means of a HFRR tester, following the ASTM D 6079-04 Standard. In this conception, a sphere of AISI 52100 steel (diameter of 6,000,05 mm, Ra 0,050,005 μm, E = 210 GPa, HRC 624, HV0,2 63147) is submitted to a reciprocating motion under a normal load of 2 N and 50 Hz frequency to promote a wear track length of 1.10.1mm in a plan disc of AISI 52100 steel (HV0,05 18410, Ra 0,020,005 μm). The testing extent time was 75 minutes, 225,000 cycles. Each one test was repeated six times to furnish the results, by means of intrinsic signatures from the signals of the lubricant film percentage, friction coefficient, contact heating, Sound Pressure Level, SPL [dB]. These signal signatures were obtained by two thermocouples and a portable decibelmeter coupled to a data acquisition system and to the HFRR system. The wettability of droplet of the diesel fuel in thermal equilibrium on a horizontal surface of a virgin plan disc of 52100 steel, Ra 0,02  0,005 μm, were measured by its contact angle of 7,0  3,5o, while the results obtained for the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of soybean oil were, respectively, 7,5  3,5o, 13,5  3,5o e 19,0  1,0o; for the distilled water, 78,0  6,0o; the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of sunflower oil were, respectively, 7,0  4,0o, 8,5  4,5o e 19,5  2,5o. Different thickness of lubricant film were formed and measured by their percentage by means of the contact resistance technique, suggesting several regimes, since the boundary until the hydrodynamic lubrication. All oils analyzed in this study promoted the ball wear scars with diameters smaller than 400 μm. The lowest values were observed in the scar balls lubricated by mixtures B100, B20 and B5 of sunflower and B20 and B5 of soybean oils (WSD < 215 μm)

Estudo de um compósito de matriz cerâmica com carga de recicláveis para o uso na construção civi

With a view to revitalizing public environments through criteria that include economy, tourism, aesthetics and respect for the environment, this paper proposes a model of kiosk manufactured with composite material blocks, to be employed as a public instrument. . The model consists of a structure composed of planned blocks and manufactured in cement-based composite, gypsum, ground and water, having the styrofoam inside filled with pet bottles of 500 ml dose. The social and environmental issue is the critical point of the work when it can, through the reuse of environmentally harmful materials such as polyethylene terephthalate PET, using such modules for the construction of various areas of Commerce, promoting the protection of the environment combined with the improvement of the quality of life of the population. The tourism factor, which is significant in the economy of the North, is also considered as the modulated kiosk has a visual aspect innovative and differentiated. The environmental issue is addressed by encouraging the reuse of PET material and EPS (polystyrene)

Avaliação da capacidade de adsorção do CO2 em zeólita 12X com gases sintéticos e originados da pirólise do lodo de esgoto

This work depicts a study of the adsorption of carbon dioxide on zeolite 13X. The activities were divided into four stages: study batch adsorption capacity of the adsorbent with synthetic CO2 (4%), fixed bed dynamic evaluation with the commercial mixture of gases (4% CO2, 1.11% CO, 1 2% H2, 0.233% CH4, 0.1% C3, 0.0233% C4 argon as inert closing balance), fixed bed dynamic modeling and evaluation of the breakthrough curve of CO2 originated from the pyrolysis of sewage sludge. The sewage sludge and the adsorbent were characterized by analysis TG / DTA, SEM, XRF and BET. Adsorption studies were carried out under the following operating conditions: temperature 40 °C (for the pyrolysis of the sludge T = 600 °C), pressures of 0.55 to 5.05 bar (batch process), flow rate of the gaseous mixture between 50 - 72 ml/min and the adsorbent masses of 10, 15 and 20 g (fixed bed process). The time for the adsorption batch was 7 h and on the fixed bed was around 180 min. The results of this study showed that in batch adsorption process step with zeolite 13X is efficient and the mass of adsorbed CO2 increases with the increases pressure, decreases with temperature increases and rises due the increase of activation temperature adsorbent. In the batch process were evaluated the breakthrough curves, which were compared with adsorption isotherms represented by the models of Langmuir, Freündlich and Toth. All models well adjusted to the experimental points, but the Langmuir model was chosen in view of its use in the dynamic model does not have implications for adsorption (indeterminacy and larger number of parameters such as occurred with others) in solving the equation. In the fixed bed dynamic study with the synthetic gas mixture, 20 g of mass adsorbent showed the maximum adsorption percentage 46.7% at 40 °C temperature and 50 mL/min of flow rate. The model was satisfactorily fitted to the three breakthrough curves and the parameters were: axial dispersion coefficient (0.0165 dm2/min), effective diffusivity inside the particle (dm2/min 0.0884) and external transfer coefficient mass (0.45 dm/min). The breakthrough curve for CO2 in the process of pyrolysis of the sludge showed a fast saturation with traces of aerosols presents in the gas phase into the fixed bed under the reaction process

Recuperação e purificação de quitosanases usando adsorção em leito expandido com streamline DEAE com modelagem e simulação usando redes neurais

Expanded Bed Adsorption (EBA) is an integrative process that combines concepts of chromatography and fluidization of solids. The many parameters involved and their synergistic effects complicate the optimization of the process. Fortunately, some mathematical tools have been developed in order to guide the investigation of the EBA system. In this work the application of experimental design, phenomenological modeling and artificial neural networks (ANN) in understanding chitosanases adsorption on ion exchange resin Streamline® DEAE have been investigated. The strain Paenibacillus ehimensis NRRL B-23118 was used for chitosanase production. EBA experiments were carried out using a column of 2.6 cm inner diameter with 30.0 cm in height that was coupled to a peristaltic pump. At the bottom of the column there was a distributor of glass beads having a height of 3.0 cm. Assays for residence time distribution (RTD) revelead a high degree of mixing, however, the Richardson-Zaki coefficients showed that the column was on the threshold of stability. Isotherm models fitted the adsorption equilibrium data in the presence of lyotropic salts. The results of experiment design indicated that the ionic strength and superficial velocity are important to the recovery and purity of chitosanases. The molecular mass of the two chitosanases were approximately 23 kDa and 52 kDa as estimated by SDS-PAGE. The phenomenological modeling was aimed to describe the operations in batch and column chromatography. The simulations were performed in Microsoft Visual Studio. The kinetic rate constant model set to kinetic curves efficiently under conditions of initial enzyme activity 0.232, 0.142 e 0.079 UA/mL. The simulated breakthrough curves showed some differences with experimental data, especially regarding the slope. Sensitivity tests of the model on the surface velocity, axial dispersion and initial concentration showed agreement with the literature. The neural network was constructed in MATLAB and Neural Network Toolbox. The cross-validation was used to improve the ability of generalization. The parameters of ANN were improved to obtain the settings 6-6 (enzyme activity) and 9-6 (total protein), as well as tansig transfer function and Levenberg-Marquardt training algorithm. The neural Carlos Eduardo de Araújo Padilha dezembro/2013 9 networks simulations, including all the steps of cycle, showed good agreement with experimental data, with a correlation coefficient of approximately 0.974. The effects of input variables on profiles of the stages of loading, washing and elution were consistent with the literature

Concepção e estudo de um biofiltro para tratamento de compostos orgânicos voláteis COVs

In the last decade, biological purification of gaseous waste has become an important alternative to many conventional methods of exhaust air treatment. More recently, biofiltration has proved to be an effective and inexpensive method for the treatment of air contaminated with volatile organic compounds (VOCs). A biofilter consists in a reactor packed with a porous solid bed material, where the microorganisms are fixed. During the biofiltration process, polluted air is transported through the biofilter medium where the contaminant is degraded. Within the biofilm, the pollutants in the waste gases are energy and carbon sources for microbial metabolism and are transformed into CO2, water and biomass. The bed material should be characterized by satisfactory mechanical and physical properties as structure, void fraction, specific area and flow resistance. The aim of this research was the biofilter construction and study of the biological degradation of ethanol and toluene, as well as the modeling of the process. Luffa cylindrica is a brazilian fiber that was used as the filtering material of the present work. The parameters and conditions studied were: composition of nutrients solution; effect of microflorae strains, namely Pseudomanas putida and Rhodococcus rhodochrous; waste gas composition; air flow rate; and inlet load of VOCs. The biofilter operated in diffusion regime and the best results for remotion capacity were obtained when a microorganisms consortion of Pseudomanas putida and Rhodococcus rhodochrous,were used, with a gas flow rate of 1 m3.h-1 and molar ratio nitrogene/phosphore N/P=2 in the nutrients solution. The maximum remotion capacity for ethanol was around 90 g.m-3.h-1 and 50 g.m-3.h-1 to toluene. It was proved that toluene has inhibitory effect on the ethanol remotion When the two VOCs were present in the same waste gas, there was a decrease of 40% in ethanol remotion capacity. Luffa cylindrica does not present considerable pressure drop. Ottengraf and van Lith models were used to represent the results obtained for ethanol and toluene, respectively. The application of the transient model indicated a satisfactory approximation between the experimental results obtained for ethanol and toluene vapors biofiltration and the ones predicted it

Investigação dos processos hidrossedimentológicos em parcela experimental no semi-árido potiguar

In northeastern semiarid, seasonality on precipitation temporal distribution, high intensity storm events and inadequate management of native vegetation can promote soil erosion. Vegetation removal causes soil surface exposure, reduces soil water storage capacity and can be the source degradation processes. In this context, this approach aims to analyze water and soil erosion processes on a 250 m2 undisturbed experimental plot with native vegetation, slope 2.5% by using 2006 and 2007 monitoring data. The site was instrumented to monitor rainfall, overland flow runoff and erosion by using a 5 m³ tank downstream the plot. Soil erosion monitoring was made by transported sediment and organic matter collection after each event. Field infiltration experiments were made at 16 points randomly distributed within the plot area by using a constant head infiltrometer during drought and rainy seasons, respectively. Infiltration data revealed high spatial and temporal variability. It was observed that during the beginning of the rainy period, 77% of the events showed runoff coefficient less than 0.05. As the rainy season began, soil water increase produced annual species germination. High intensity storms resulted in runoff coefficients varying between 0.33 and 0.42. Once the annual species was established, it was observed that approximately 39% of the events produced no runoff, which reflects an increase on soil water retention capacity caused by the vegetation. A gradual runoff reduction during the rainy season emphasizes the effect of vegetative density increase. Soil erosion observed data allowed to fit an empirical relationship involving soil loss and precipitation height, which was used to analyze the plot installation impact on soil erosion. Observed soil loss in 2006 and 2007 was 230 Kg/ha and 54 Kg/ha, respectively

Capacidade cardiorrespiratória e distribuição de gordura corporal de mulheres com 50 anos ou mais

Verificar a relação entre capacidade cardiorrespiratória e gordura corporal em mulheres. Foram analisadas 229 mulheres com idade entre 50 e 84 anos. Foi realizada avaliação antropométrica e calculada a razão cintura/quadril, bem como o índice de conicidade. A capacidade cardiorrespiratória foi avaliada pelo teste de caminhada de seis minutos. Com o pedômetro foi possível avaliar: velocidade, comprimento da passada e total de passos. Os resultados foram distribuídos em quartil, e a comparação feita pela análise de variância com post-hoc. A relação entre teste de caminhada de seis minutos e a antropometria foi feita pela correlação de Pearson. Os resultados revelaram que mulheres com capacidade cardiorrespiratória no quartil4 apresentaram idade estatisticamente menor (p<0,05) que as do quartil1. As medidas antropométricas apresentaram valores menores (p<0,05), quando comparados os resultados dos quartis3 e 4 com os quartis1 e 2. Conclui-se que mulheres com maior tecido adiposo e acúmulo de gordura central apresentam menor capacidade cardiorrespiratória.

Propriedades mecânicas do músculo de ratos adultos e idosos, exercitado pós-imobilização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Capacidade funcional de hemiparéticos crônicos submetidos a um programa de fisioterapia em grupo

Este estudo tem como objetivos analisar a eficácia da fisioterapia em grupo sobre a marcha, o equilíbrio corporal e o risco de queda, e verificar se há correlação entre a capacidade funcional da marcha e o equilíbrio em indivíduos com hemiparesia crônica. Participaram do estudo 21 adultos hemiparéticos, com idade média de 58,9±10,6 anos, com seqüela de no mínimo 1 ano após acidente vascular encefálico isquêmico ou hemorrágico. Os sujeitos foram submetidos a um programa de 1 hora de fisioterapia em grupo duas vezes por semana durante seis meses. Foram avaliados por meio da escala de equilíbrio de Berg (EEB) e do teste de levantar e caminhar cronometrado TLCC (TUG, na sigla em inglês de timed up & go) antes do programa, após 13 e ao fim de 26 semanas. Os resultados mostram uma redução progressiva, embora não-significativa, no tempo de execução do TLCC e aumento progressivo, também não-significativo, do escore na EEB. Foi observada forte correlação entre as duas escalas (r=0,7, p<0,05). Assim, a terapia não foi efetiva para produzir melhora nos escores dos testes, mas contribuiu para manter a mobilidade.

Força muscular respiratória e capacidade funcional em idosas hipertensas com sonolência diurna excessiva

The restriction of physical fitness is directly related with hypertension and sleep disorders, while the respiratory muscle strength is associated with hypertension, but the literature is scarce regarding its relationship with sleep disorders and particularly with excessive daytime sleepiness. Objectives: To compare physical fitness and strength of respiratory muscles between people with hypertension with excessive daytime sleepiness (EDS) and non EDS people, those who do not feel excessive daytime sleepiness, in addition to relate aerobics resistance and functional mobility of patients. Methods: An observational, analytical and transversal study, evaluated 32 elderly with hypertension, divided into two groups (EDS and non EDS), in which the following topics were measured; respiratory muscular strength, functional fitness, level of physical activity, level of excessive daytime sleepiness, quality of sleep and intensity of the patients snoring. Results: There was a significant difference in the level of EDS (P=0,00) and quality of sleep (p=0,03), however, the data related to snoring intensity (p=0,18), maximum inspiratory pressure PImax (p=0,39) and maximum expiratory pressure PEmax (p=0,98) did not show any difference. Also, no significant difference was observed concerning physical fitness, presenting p=0,08 for the sitting and getting up test on the chair in 30 ; p=0,54 for the extension and flexing of the elbow test in 30 ; p=0,38 for the walking test 6 ; p=0,38 for the parking gear test 2 , p=0,08 for the sitting and reaching test; p=0,42 for the scratching the back test; p=0,49 for the getting up and walking test; and p=0,62 for the global rate of activity limitation. There was moderate positive correlation between 6MWT and 2MST, r=0,54 (p=0,01) and negative moderate correlation between 6MWT and TUG, r=-0,61 (p=0,000) and between 2MST and TUG, r=-0,60 (p=0,000). Conclusion: The presence of EDS in the hypertension people studied, showed a bad quality of sleep, however this sleepiness did not influence the strength of the respiratory muscles. The physical fitness came out diminished in all hypertension people, regardless of the presence or non presence of sleep disturbance; and there is a close relationship between cardiovascular resistance and physical mobility, since when there is less cardiovascular resistance, there is precarious physical mobility and vice-versa

Avaliação da capacidade de caminhar do portador de obesidade mórbida utilizando teste de caminhada de 6 minutos

Introduction: The ability to walk is impaired in obese by anthropometric factors (BMI and height), musculoskeletal pain and level of inactivity. Little is known about the influence of body adiposity and the acute response of the cardiovascular system during whole the 6-minute walk test (6mWT). Objective: To evaluate the effect of anthropometric measures (BMI and WHR waist-to-hip ratio), the effort heart and inactivity in ability to walk the morbidly obese. Materials and Methods: a total 36 morbidly obese (36.23 + 11.82 years old, BMI 49.16 kg/m2) were recruited from outpatient department of treatment of obesity and bariatric surgery in University Hospital Onofre Lopes and anthropometric measurements of obesity (BMI and WHR), pulmonary function, pattern habitual physical activity (Baecke Questionnaire) and walking capacity (6mWT). The patient was checking to measure: heart rate (HR), breathing frequency (BF), peripheral oxygen saturation, level of perceived exertion, systemic arterial pressure and duplo-produto (DP), moreover the average speed development and total distance walking. The data were analysed between gender and pattern of body adiposity, measuring the behavior minute by minute of walking. The Pearson and Spearmam correlation coefficients were calculated, and stepwise multiple Regression examined the predictors of walking capacity. All analyses were performed en software Statistic 6.0. Results: 20 obese patients had abdominal adiposity (WHR = 1.01), waist circumference was 135.8 cm in women (25) and 139.8 cm in men (10). Walked to the end of 6mWT 412.43 m, with no differences between gender and adiposity. The total distance walked by obesity alone was explained by BMI (45%), HR in the sixth minute (43%), the Baecke (24%) and fatigue (-23%). 88.6% of obese (31) performed the test above 60% of maximal HR, while the peak HR achieved at 5-minute of 6mWT. Systemic arterial pressure and DP rised after walking, but with no differences between gender and adiposity. Conclusion: The walk of obese didn´t suffers influence of gender or the pattern of body adiposity. The final distance walked is attributed to excess body weight, stress heart, the feeling of effort required by physical activity and level of sedentary to obese. With a minute of walking, the obeses achieved a range of intensity cardiovascular trainning

Exercício físico de baixa intensidade na dpoc: comparação dos programas solo e aquático

Physical Exercise (PE) is a necessary component in the management in COPD patients, where respiratory symptoms are associated with reduced functional capacity. Even with the increase in the number of studies that have been published and the therapeutics success using aquatic therapy approach, studies using PE in water in COPD patients are so few. Objective: the aim of this present study was to analyze the effects of low intensity water exercise in COPD patients, developed in two different places aquatic and ground. Methods: This is a randomized clinical trial study, 42 patients with moderate to very severe DPOC were recruited for the study, mean age of 63,2  10,9 years old. Randomized in 3 groups: Control Group (CG), Land Group (LG) and Water Group (WG). The PE protocol was performed in a period of 8 weeks, with frequency of 3 times per week. The CG participated in an educational program. All the patients were assessed twice through spirometry, respiratory muscular strength, the 6-min walk test, the quality of life (SF-36 and SGRQ), the LCADL, the MRC, the BODE index and the upper limbs (UP) incremental test. Results: There was a significant difference after the approaches in DP6 from the WG (p=0,02); in VEF1 in LG (p=0,00) and WG (p=0,01); in MIP in LG (p=0,01) and WG (p=0,02); in MEP in LG (p=0,02) and WG (p=0,01); the MRC decreases in WG (p=0,00). there was an increase of the weight supported by the UP in LG (p=0,00) and WG (p=0,01). The LG showed an increase of the quality of life represented by the SGRQ total score (p=0,00). The BODE index decreased in LG (p=0,00) and WG (p=0,01). In LCDAL, the LG showed a decrease. Conclusion: This data in this present study suggest that both approaches of low intensity exercise showed to be beneficial in moderate to very severe COPD patients. The WG showed additional benefits in physical function, pointing to a new therapeutic modality for COPD patients

Efeito do treinamento resistido na pressão arterial e capacidade funcional de idosas hipertensas

The results of studies about the ideal resistance training intensity for reduction of resting blood pressure levels, as well as this type of training to increase the functional capacity of hypertensive older women are still unclear, since the few investigations usually analyze young individuals normotensive, and the literature lacks precise information in elderly hypertensive subjects. Objectives: To determine the effect of two resistance training intensities on resting blood pressure and the effect of resistance training on functional capacity in elderly women with systemic arterial hypertension, analyzing these variables before and after eight weeks of intervention. Methods: Patients underwent eight weeks of resistance training, with a frequency of three times per week on alternate days, in the afternoon. The exercises performed were: leg press, bench press, knee extension, lat pull-down, knee flexion, shoulder abduction, standing cable hip abduction and biceps curl. Results: It was found that patients who underwent training with moderate resistance, showed a reduction on resting values of diastolic blood pressure (DBP) p<0.03 and of mean arterial pressure (MAP) p<0.03. Patients who underwent mild resistance training showed reduction in resting values of MAP (p<0.03) and a tendency to decrease in DBP (p<0.06). With regard to functional capacity, the results showed significant increase in the strength of arms and legs, agility and aerobic endurance (p<0.001) and maintaining flexibility (p>0.05). Conclusion: The data indicated that both mild and moderate resistance training, even when started in old age, promoted cardiovascular benefits and also improve the functional capacity of hypertensive older women.

Avaliação das variáveis cardiovasculares, capacidade de caminhar e nível de atividade física de obesos mórbidos antes e depois da cirurgia bariátrica

Morbidly obese patients present an increase in heart rate, blood pressure and perceived exertion besides lower walking ability compared to normal weight people. However, little is known about how these variables are presented after bariatric surgery. Moreover, despite the distance walked during the six-minute walk (6MWT) improve after surgery is not well established if the level of physical activity influences this improvement. Objective: To evaluate cardiovascular performance, perceived effort, ability of walking and physical activity level of patients with morbid obesity before and after bariatric surgery. Methods: The cardiovascular performance, perception of effort, the ability to walk and level of physical activity were assessed in 22 patients before (BMI = 50.4 kg/m2) and after (BMI = 34.8 kg/m2) bariatric surgery through the 6MWT. The heart rate, blood pressure and perceived exertion were assessed at rest, at the end of the 6MWT and in the second minute post-test (HR recovery). The ability to walk was measured by total distance walked at the end of the test while the level of physical activity was estimated by applying the Baecke questionnaire, analyzing domains occupation, leisure and locomotion and leisure and physical activity. Results: The HR at rest and recovery decreased significantly (91.2 ± 15.8 bpm vs. 71.9 ± 9.8 bpm, 99.5 ± 15.3 bpm vs 82.5 ± 11.1 bpm, respectively), as well as all the arterial pressure and perceived exertion after surgery. The distance achieved by the patients increased by 58.4 m (p = 0.001) postoperatively. Time postoperatively had correlation with the percentage of excess weight lost (r = 0.48, p = 0.02), BMI (r =- 0.68, p = 0.001) and the Baecke (r = 0.52, p = 0.01) which did not happen with the distance walked (r = 0.37, p = 0.09). Despite weight loss, patients showed no difference in the level of physical activity in any of the areas before and after surgery. Conclusion: The cardiovascular performance, the perception of effort and ability to walk seem to improve after bariatric surgery. However, despite improvement in the ability to walk by the distance achieved in the 6MWT after weight loss, this is not reflected in an increase in physical activity level of obese patients after surgery