Desenvolvimento de uma ferramenta computacional para aplicação em métodos de elevação por bombeio centrífugo submerso

The Electrical Submersible Pump (ESP) has been one of the most appropriate solutions for lifting method in onshore and offshore applications. The typical features for this application are adverse temperature, viscosity fluids and gas environments. The difficulties in equipments maintenance and setup contributing to increasing costs of oil production in deep water, therefore, the optimization through automation can be a excellent approach for decrease costs and failures in subsurface equipment. This work describe a computer simulation related with the artificial lifting method ESP. This tool support the dynamic behavior of ESP approach, considering the source and electric energy transmission model for the motor, the electric motor model (including the thermal calculation), flow tubbing simulation, centrifugal pump behavior simulation with liquid nature effects and reservoir requirements. In addition, there are tri-dimensional animation for each ESP subsytem (transformer, motor, pump, seal, gas separator, command unit). This computer simulation propose a improvement for monitoring oil wells for maximization of well production. Currenty, the proprietaries simulators are based on specific equipments manufactures. Therefore, it is not possible simulation equipments of another manufactures. In the propose approach there are support for diverse kinds of manufactures equipments

Estudo da qualidade de serviço de uma aplicação VoIP em ambientes wireless com handoff

This work deals with experimental studies about VoIP conections into WiFi 802.11b networks with handoff. Indoor and outdoor network experiments are realised to take measurements for the QoS parameters delay, throughput, jitter and packt loss. The performance parameters are obtained through the use of software tools Ekiga, Iperf and Wimanager that assure, respectvely, VoIP conection simulation, trafic network generator and metric parameters acquisition for, throughput, jitter and packt loss. The avarage delay is obtained from the measured throughput and the concept of packt virtual transmition time. The experimental data are validated based on de QoS level for each metric parameter accepted as adequated by the specialized literature

Implementação experimental de filtro ativo paralelo de potência com aplicação a gerador de indução trifásico

This work describes the experimental implementation of a shunt active power filter applied to a three-phase induction generator. The control strategy of active filter turned to the excitation control of the machine and to decrease the harmonics in the generator output current. Involved the implementation of a digital PWM switching, and was made a comparison of two techniques for obtaining the reference currents. The first technique is based on the synchronous dq reference method and the second on the theory of instantaneous power. The comparison is performed via simulation and experimental results. To obtain the experimental results, was mounted a bench trial and the control and communications needed were implemented using DSP - MS320F2812. The simulation results and experimental data proved the efficiency of the filter to apply, highlighting the technique of instantaneous power

Efeitos da aplicação de efluente de tratamento de esgoto na fertilidade do solo e produtividade de pepino sob irrigação subsuperficial

O experimento foi conduzido com o objetivo de avaliar técnicas para a aplicação de águas residuárias na agricultura, proporcionando melhor reutilização de água, recurso natural atualmente escasso e muito mal disponibilizado. Utilizou-se da cultura de pepino (Cucumis sativus L.) em estufa, com oito parcelas irrigadas com efluentes de tratamento de esgoto residencial e oito parcelas irrigadas com água tratada e distribuída pela SABESP (tratamento-testemunha), ambas abastecidas por sistema de irrigação subsuperficial, avaliando-se a produção média por planta, a fertilidade do solo e a disposição de nutrientes na água do solo. Nas análises do solo, verificaram-se maiores teores de P, K e CTC no solo irrigado com efluentes. Nesse mesmo tratamento, constataram-se os maiores teores de N, nitrato, Ca, Mg, Zn e S para as análises da água retida na matriz do solo. Quanto à produção total média por planta, as parcelas irrigadas com efluente apresentaram 2.769,6 g de matéria fresca, superior aos 1.968,6 g verificados no tratamento-testemunha, demonstrando a importância da utilização de efluente de esgoto para o fornecimento de nutrientes e aumento de produtividade.

Estudo da detecção preventiva da osteoporose pela aplicação da variação da permissividade elétrica a partir da sondagem eletromagnética

This paper proposes a method based on the theory of electromagnetic waves reflected to evaluate the behavior of these waves and the level of attenuation caused in bone tissue. For this, it was proposed the construction of two antennas in microstrip structure with resonance frequency at 2.44 GHz The problem becomes relevant because of the diseases osteometabolic reach a large portion of the population, men and women. With this method, the signal is classified into two groups: tissue mass with bony tissues with normal or low bone mass. For this, techniques of feature extraction (Wavelet Transform) and pattern recognition (KNN and ANN) were used. The tests were performed on bovine bone and tissue with chemicals, the methodology and results are described in the work

Viabilidade econômica dos sistemas manual e mecanizado de aplicação de herbicidas em ferrovias

A aplicação mecanizada de herbicidas em ferrovias tem como principal vantagem a grande capacidade operacional, cobrindo trechos extensos em curtos espaços de tempo. Entretanto em função das características dos equipamentos utilizados, quase sempre ocorre grande desperdício de herbicida. A aplicação manual, através de pulverizadores costais, tem como principal vantagem a possibilidade da pulverização dirigida às áreas infestadas, diminuindo a quantidade de herbicida aplicado. Por outro lado, sua reduzida capacidade operacional faz com que a aplicação de longos trechos seja demorada, tornando-a, assim, mais dependente dos problemas climáticos e operacionais da ferrovia. O objetivo do trabalho foi realizar uma análise comparativa das características operacionais e econômicas destes sistemas de aplicação, apontando os fatores mais importantes a serem avaliados para a sua implantação. Para tanto, foram realizadas simulações em computador, baseando-se em diversas equações matemáticas e dados levantados no campo. Os resultados mostraram que a aplicação manual apresentou-se mais econômica apenas para trechos com baixas infestações (até 10%, e média). Na composição de custos, os gastos com herbicidas corresponderam a cerca de 80% do total para a aplicação mecanizada e apenas 8% na manual. Levando-se em conta os fatores operacionais e de mão-de-obra, em apenas um dos trechos avaliados houve vantagem econômica do uso da aplicação manual.

Influência da chuva após aplicação de imazamox sobre o controle de plantas daninhas aquáticas

This study aimed to evaluate the imazamox control efficiency on aquatic plants under different intervals of simulated rain after its spraying. The experiment was carried out in completely random design with four replications. The imazamox at 290.4 g ha(-1) was tested on three aquatic weed species, Eichhornia crassipes (Mart.) Solms, Pistia stratiotes L. and Salvinia adnata Desv and, under eight different rain-free periods (0, 2, 4, 6, 8, 12, 24 hours). Rainfall was simulated using a sprinkler irrigation system (20mm). There was a good control of Eichhornia crassipes, regardless of periods without rain after herbicide spraying. However, Pistia stratiotes took a rain-free period of at least eight hours to obtain an effective control. In Salvinia adnata, whole rain-free periods affected the control provided by the herbicide.

Cobre e zinco no material percolado e no solo com a aplicação de água residuaria de suinocultura em solo cultivado com soja

O objetivo deste trabalho foi avaliar possíveis efeitos da aplicação de taxas de água residuária de suinocultura (ARS), quanto às concentrações de cobre e zinco, tanto no solo quanto na água percolada de lisímetros de drenagem, durante o ciclo da cultura da soja. O experimento foi conduzido em ambiente protegido, onde havia 24 lisímetros de drenagem. Semeou-se soja cultivar CD 202, e foram aplicadas ARS nas seguintes dosagens: 0; 100; 200 e 300 m³ ha-1 no ciclo, combinadas com duas adubações na semeadura (com e sem adição da adubação recomendada na semeadura), em três repetições por tratamento. Foram feitas seis coletas do material percolado durante o ciclo da cultura e realizadas determinações de cobre e zinco. No solo, foram feitas três coletas em cada parcela experimental, para a determinação do pH, da matéria orgânica, da capacidade de troca catiônica, do cobre e do zinco. O delineamento foi em blocos casualizados, num esquema fatorial de 4 x 2. Observou-se que o cobre no solo não apresentou diferenças significativas com a aplicação de ARS e adubação, enquanto as concentrações de zinco no solo foram influenciadas pelas taxas aplicadas de ARS. As transferências de cobre e de zinco por percolação foram pouco expressivas.

Depósitos de calda obtidos com a aplicação aérea de defensivos na cultura da banana

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo de antenas patches de microfita miniaturizadas em banda larga para aplicação em dispositivos móveis e portáteis

This work presents techniques used to design and manufacture microstrip patch antennas for applications in portable and mobile devices. To do so, are evaluated several factors that can influence the performance of microstrip patch antennas. Miniaturization techniques are studied and employed in order to apply this type of antenna in mobile and / or mobile. The theories of microstrip patch antennas are addressed by analyzing characteristics such as constitution, kinds of patches, substrates, feeding methods, analysis methods, the main advantages and disadvantages and others. Techniques for obtaining broadband microstrip patch antennas were surveyed in literature and exemplified mainly by means of simulations and measurements. For simulations of the antennas was used the commercial software . In addition, antenna miniaturization techniques have been studied as a main concern the fundamental limits of antennas with special attention to electrically small antennas because they are directly linked to the microstrip patch antennas. Five design antennas are proposed to demonstrate the effectiveness of techniques used to obtain the microstrip patch antennas broadband and miniaturized for use in mobile devices and/or portable. For this, the proposed antennas were simulated, built and measured. The antennas are proposed to be used in modern systems of wireless communications such as DTV, GPS, IEEE 802.16, IEEE 802.11, etc. The simulations of the antennas were made in business and computer programs. The measured results were obtained with a parser Vector of networks of the Rhode and Schwarz model ZVB 14

Estudos e projetos de filtro interdigital em microfita para aplicação prática ao transponder do satélite ITASAT

This work shows a theoretical analysis together with numerical and experimental results of transmission characteristics from the microstrip bandpass filters with different geometries. These filters are built over isotropic dielectric substrates. The numerical analysis is made by specifical commercial softwares, like Ansoft Designer and Agilent Advanced Design System (ADS). In addition to these tools, a Matlab Script was built to analyze the filters through the Finite-Difference Time-Domain (FDTD) method. The filters project focused the development of the first stage of filtering in the ITASAT s Transponder receptor, and its integration with the others systems. Some microstrip filters architectures have been studied, aiming the viability of implementation and suitable practical application for the purposes of the ITASAT Project due to its lowspace occupation in the lower UHF frequencies. The ITASAT project is a Universityexperimental project which will build a satellite to integrate the Brazilian Data Collect System s satellite constellation, with efforts of many Brazilian institutes, like for example AEB (Brazilian Spatial Agency), ITA (Technological Institute of Aeronautics), INPE/CRN (National Institute of Spatial Researches/Northeastern Regional Center) and UFRN (Federal University of Rio Grande do Norte). Comparisons were made between numerical and experimental results of all filters, where good agreements could be noticed, reaching the most of the objectives. Also, post-work improvements were suggested.

Aplicação de reguladores vegetais no retardamento da abscisão de frutos de laranjeira-'Hamlin'

O trabalho avaliou os efeitos de auxinas e giberelina, combinadas e aplicadas em pré-colheita no desenvolvimento e na porcentagem de queda natural dos frutos de laranjeira-'Hamlin' (Citrus sinensis Osbeck). Foram realizadas 3 aplicações a intervalos de 45 dias dos seguintes tratamentos, via foliar: GA3 + NAA a 12,5mg.L-1 de cada; GA3 + NAA a 25mg.L-1; GA3 + 2,4-D a 12,5mg.L-1; GA3 + 2,4-D a 25mg.L-1; NAA + 2,4-D a 12,5mg.L-1; NAA + 2,4-D a 25mg.L-1; testemunha (água). As variáveis avaliadas foram: porcentagem de queda natural dos frutos (%), massa fresca de frutos (g) e teor de suco no fruto (%). Os resultados obtidos mostram que a utilização de reguladores vegetais atrasa a queda natural de frutos de laranjeira-'Hamlin', podendo-se prolongar o período de colheita, destacando-se o tratamento com GA3 25mg.L-1 +2,4-D 25mg.L-1 e também não influenciaram no aumento da massa fresca e no teor de suco dos frutos.

Aplicação de técnicas de aprendizado de máquina no reconhecimento de classes estruturais de proteínas

Nowadays, classifying proteins in structural classes, which concerns the inference of patterns in their 3D conformation, is one of the most important open problems in Molecular Biology. The main reason for this is that the function of a protein is intrinsically related to its spatial conformation. However, such conformations are very difficult to be obtained experimentally in laboratory. Thus, this problem has drawn the attention of many researchers in Bioinformatics. Considering the great difference between the number of protein sequences already known and the number of three-dimensional structures determined experimentally, the demand of automated techniques for structural classification of proteins is very high. In this context, computational tools, especially Machine Learning (ML) techniques, have become essential to deal with this problem. In this work, ML techniques are used in the recognition of protein structural classes: Decision Trees, k-Nearest Neighbor, Naive Bayes, Support Vector Machine and Neural Networks. These methods have been chosen because they represent different paradigms of learning and have been widely used in the Bioinfornmatics literature. Aiming to obtain an improvment in the performance of these techniques (individual classifiers), homogeneous (Bagging and Boosting) and heterogeneous (Voting, Stacking and StackingC) multiclassification systems are used. Moreover, since the protein database used in this work presents the problem of imbalanced classes, artificial techniques for class balance (Undersampling Random, Tomek Links, CNN, NCL and OSS) are used to minimize such a problem. In order to evaluate the ML methods, a cross-validation procedure is applied, where the accuracy of the classifiers is measured using the mean of classification error rate, on independent test sets. These means are compared, two by two, by the hypothesis test aiming to evaluate if there is, statistically, a significant difference between them. With respect to the results obtained with the individual classifiers, Support Vector Machine presented the best accuracy. In terms of the multi-classification systems (homogeneous and heterogeneous), they showed, in general, a superior or similar performance when compared to the one achieved by the individual classifiers used - especially Boosting with Decision Tree and the StackingC with Linear Regression as meta classifier. The Voting method, despite of its simplicity, has shown to be adequate for solving the problem presented in this work. The techniques for class balance, on the other hand, have not produced a significant improvement in the global classification error. Nevertheless, the use of such techniques did improve the classification error for the minority class. In this context, the NCL technique has shown to be more appropriated

Aplicação do método LTT às estruturas retangulares e triangulares em multicamadas e empilhadas em substratos PBG para comunicações móveis

Recently the planar antennas have been studied due to their characteristics as well as the advantages that they offers when compared with another types of antennas. In the mobile communications area, the need for this kind of antennas have became each time bigger due to the intense increase of the mobile communications that needs of antennas which operate in multifrequency and wide bandwidth. The microstrip antennas presents narrow bandwidth due the loss in the dielectric generated by radiation. Another limitation is the radiation pattern degradation due the generation of surface waves in the substrate. In this work some used techniques to minimize the disadvantages (previously mentioned) of the use of microstrip antennas are presented, those are: substrates with PBG material - Photonic Bandgap, multilayer antennas and with stacked patches. The developed analysis in this work used the TTL - Transverse Transmission Line method in the domain of Fourier transform, that uses a component of propagation in the y direction (transverse to the direction real of propagation z), treating the general equations of electric and magnetic field as functions of y and y . This work has as objective the application of the TTL method to microstrip structures with single and multilayers of rectangular and triangular patches, to obtaining the resonance frequency and radiation pattern of each structure. This method is applied for the treatment of the fields in stacked structures. The Homogenization theory will be applied to obtaining the effective permittivity for s and p polarizations of the substrate composed of PBG material. Numerical results for the triangular and rectangular antennas with single layer, multilayers resonators with triangular and rectangular patches are presented (in photonic and isotropic substrates). Conclusions and suggestions for continuity of this work are presented

Uma arquitetura para sistemas supervisórios industriais e sua aplicação em processos de elevação artificial de petróleo

The using of supervision systems has become more and more essential in accessing, managing and obtaining data of industrial processes, because of constant and frequent developments in industrial automation. These supervisory systems (SCADA) have been widely used in many industrial environments to store process data and to control the processes in accordance with some adopted strategy. The SCADA s control hardware is the set of equipments that execute this work. The SCADA s supervision software accesses process data through the control hardware and shows them to the users. Currently, many industrial systems adopt supervision softwares developed by the same manufacturer of the control hardware. Usually, these softwares cannot be used with other equipments made by distinct manufacturers. This work proposes an approach for developing supervisory systems able to access process information through different control hardwares. An architecture for supervisory systems is first defined, in order to guarantee efficiency in communication and data exchange. Then, the architecture is applied in a supervisory system to monitor oil wells that use distinct control hardwares. The implementation was modeled and verified by using the formal method of the Petri networks. Finally, experimental results are presented to demonstrate the applicability of the proposed solution