Breeder age and bone development in broiler chicken embryos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Época de coleta e ácido indolbutírico no enraizamento de estacas de espirradeira (Nerium oleander L.)

A espirradeira (Nerium oleander L.) é uma importante espécie arbórea ornamental, muito utilizada no meio urbano. É propagada por estacas, porém a porcentagem de enraizamento é baixa e não há estudos sobre fatores que influenciam nesse processo. Este trabalho teve, portanto, o objetivo de estudar o efeito da época de coleta e do ácido indolbutírico (AIB) no enraizamento de estacas de duas variedades de espirradeira (Nerium oleander L.), determinadas pela coloração das flores (rosa e branca). O experimento foi instalado na UNESP, Campus de Jaboticabal/SP, no verão e no inverno. O delineamento experimental foi em blocos casualizados em esquema fatorial 2 x 2 x 4 (duas variedades combinadas com duas estações do ano e quatro concentrações de AIB - 0, 1.000, 2.000 e 4.000 mg kg-1). As avaliações foram realizadas 60 dias após a estaquia, sendo estas as variáveis: porcentagem de enraizamento, número médio, comprimento e massa de matéria seca de raízes. Concluiu-se que o enraizamento de ambas as variedades de espirradeira (rosa e branca) foi superior no verão. A variedade de flores rosas apresentou maior número e comprimento médio de raízes no verão, porém as maiores porcentagens de enraizamento e massa de matéria seca de raízes foram encontradas no inverno. O ácido indolbutírico foi efetivo para aumentar a porcentagem de enraizamento nas concentrações testadas de 1.000 e 2.000 mg kg-1; maior número, comprimento e massa de matéria seca de raízes foram obtidos na concentração de 2.000 mg kg-1.

Superfícies geomórficas e atributos de Latossolos em uma seqüência Arenítico-Basáltica da região de Jaboticabal (SP)

Em um segmento de vertente com substrato de arenito em contato com basalto, regionalmente muito freqüente, pretendeu-se não só relacionar as superfícies geomórficas com os atributos físicos, químicos e mineralógicos dos Latossolos nelas encontrados, mas também testar métodos geoestatísticos para localização de limites dessas superfícies. Usando critérios geomorfológicos, três superfícies foram identificadas e topograficamente caracterizadas. Os solos foram amostrados, a intervalos regulares de 25 m, na profundidade de 0,6 a 0,8 m (topo do horizonte B), em uma transeção de 1.700 m perfazendo 109 pontos. Nas amostras, foram analisados: densidade de partículas, granulometria, CTC do solo, CTC da argila, Fe total da argila (ataque por H2SO4) e óxidos de Fe livres (por dissolução seletiva). A fração argila desferrificada foi analisada por difração de raios X. Com base na estratigrafia e variações do relevo local, foram identificadas e diferenciadas, no campo, três superfícies geomórficas. Analisaram-se também o perfil altimétrico e o modelo de elevação digital do terreno. Observou-se que as três diferentes superfícies estão bem relacionadas com os atributos físicos, químicos e mineralógicos dos seus respectivos solos. Na parte inferior desta vertente, superfície mais recente e sobre basalto, em Latossolo Vermelho eutroférrico típico, foram encontradas as maiores variabilidades da declividade, da argila e de Fe. As variações da inclinação do terreno, quando analisadas sistematicamente pelo split moving windows dissimilarity analysis (análise estatística de dissimilaridade, em segmentos móveis), mostraram que este método estatístico pode ser usado para ajudar a localizar os limites entre superfícies geomórficas. As variações dos solos da transeção, e arredores, mostraram-se relacionadas com idade, inclinação do terreno e litologia. O trabalho geomórfico detalhado forneceu importantes informações para subsidiar os trabalhos de levantamento de solos e de pedogênese.

Análise de Argamassas Com Substituição Parcial do Cimento Portland Por Cinza Residual de Lenha de Algaroba

With the increase in cement consumption, it has quickly become one of the inputs most consumed by mankind over the last century. This has caused an increase in CO2 emissions, as cement production releases large quantities of this gas into the atmosphere. Adding this fact to the growing consciousness of environmental preservation, it has led to a search for alternatives to cement to complement its derivatives, in the form of waste materials like the ashes. This research aimed to analyze the properties of mortars in fresh and hardened state with partial replacement of Portland cement by residual algaroba wood ash (CRLA) potteries produced by the state of Rio Grande do Norte. The CRLA was collected and sieved, where part of it was ground and characterized in comparison with that just sifted, being characterized according to its chemical composition, grain size, fineness, density, bulk density and index of pozzolanic activity. It was found that the wood ash does not act as pozzolan, and grinding it has not changed its characteristics compared to those just sifted, not justifying its use. Two traces were adopted for this research: 1:3 (cement: fine sand) and 1:2:8 (cement: hydrated lime: medium sand); both in volume, using as materials the CRLA just sifted, CP II F-32 Portland cement, CH-I hydrated lime, river sand and water from the local utility. For each trace were adopted six percentages of partial replacement of cement for wood ash: 0% (control) 5%, 7%, 10%, 12% and 15%. In the fresh state, the mortars were tested towards their consistency index and mass density. In the hardened state, they were tested towards their tensile strength in bending, compressive strength and tensile adhesion strength, and its mass density in the hardened state. The mortar was also analyzed by scanning electron microscopy and X-ray diffraction. Furthermore, it was classified according to NBR 13281 (2005). The results showed that up to a content of 5% substitution and for both traces, the residual algaroba wood ash can replace Portland cement without compromising the mortars microstructure and its fresh and hardened state

Aspectos quantitativos de carcaças de bovinos de diferentes raças, alimentados com diferentes níveis de energia

Objetivou-se avaliar as características quantitativas da carcaça de bovinos machos não castrados, terminados em confinamento e abatidos aos 13-14 meses de idade. Foram utilizados 16 bezerros com nove meses de idade e peso médio inicial de 220 kg (oito Aberdeen Angus - AA e oito Hereford - HE), submetidos a dois níveis de energia (3,07 e 3,18 Mcal/kg de MS). O desenho experimental foi inteiramente casualizado, em arranjo fatorial 2 x 2 (duas raças e dois níveis de energia). O volumoso utilizado foi a silagem de milho, com 36% de grãos na matéria seca (MS). O concentrado nos tratamentos de menor nível de energia participou com 12% e naqueles de maior nível, com 32% da MS da dieta. Os animais foram abatidos quando, por estimativa, as carcaças apresentaram, na média, um mínimo de 190 kg. Os animais AA apresentaram maior rendimento de carcaça quente (54,95 contra 53,75%), maior comprimento de perna (64,12 contra 62,12 cm) e maior área do músculo Longissimus/100 kg de carcaça (29,31 contra 27,41 cm²). Os animais que receberam o maior nível de energia na dieta apresentaram maior comprimento de perna (71,75 contra 64,50 cm) e melhor conformação da carcaça (11,25 contra 10,12 pontos). Observou-se interação significativa entre raça e nível de energia para a espessura de gordura subcutânea, sendo a maior espessura verificada nas carcaças dos animais HE, que receberam o menor nível de energia.

Taxa de passagem e parâmetros ruminais em bovinos suplementados com enzimas fibrolíticas

Avaliou-se o efeito da adição de enzimas fibrolíticas (celulase e xilanase) sobre as taxas de passagem de partículas e de diluição e os parâmetros ruminais (pH e nitrogênio amoniacal) em animais consumindo dietas contendo silagem de milho e feno de tifton 85 (Cynodon spp.) como volumoso. Oito bovinos com fístulas no rúmen e no duodeno foram distribuídos em dois quadrados latinos 4 x 4, com os tratamentos distribuídos em esquema fatorial 2 x 2 (duas fontes de volumoso e adição ou não de enzimas). O complexo enzimático foi proveniente de fonte comercial e extraído dos fungos Aspergillus niger e Trichoderma longibrachiatum, sendo fornecido na proporção de 12 g/animal/dia, misturado à ração total. Para as taxas de passagem, foram utilizados como marcadores das fases sólida e líquida o cromo-mordente e o cobalto-EDTA, respectivamente. Não houve efeito das enzimas sobre o pH e as concentrações de N-NH3, que apresentaram médias de 6,5 e 22,10 mg/100 mL, respectivamente. A taxa de passagem de partículas no rúmen não foi influenciada pela suplementação enzimática, com médias de 3,4 e 3,0%/h para as dietas contendo silagem de milho e feno de tifton, respectivamente. A taxa de diluição aumentou de 10,07 para 11,84%/h com a adição de enzimas. A suplementação com enzimas fibrolíticas em dietas formuladas com silagem de milho e feno de tifton como volumoso praticamente não alterou os parâmetros avaliados.

Eficiência de síntese microbiana e atividade enzimática em bovinos submetidos à suplementação com enzimas fibrolíticas

Avaliou-se o efeito da suplementação com enzimas fibrolíticas (celulase e xilanase) sobre a eficiência de síntese microbiana e a atividade enzimática da beta-1,4-endoglucanase (celulase) em animais consumindo dietas contendo silagem de milho e feno de tifton 85 (Cynodon spp.) como volumoso. Oito bovinos com fístulas no rúmen e no duodeno foram distribuídos em dois quadrados latinos 4 x 4, em esquema fatorial 2 x 2 (duas fontes de volumoso e adição ou não de enzimas). O complexo enzimático, proveniente de fonte comercial e extraído dos fungos Aspergillus niger e Trichoderma longibrachiatum, foi fornecido misturado à ração total na proporção de 12 g/animal/dia. A adição de enzimas às dietas contendo silagem de milho e feno de tifton 85 aumentou a atividade da beta-1,4-endoglucanase no fluido ruminal. Não houve efeito das enzimas sobre a eficiência de síntese de proteína microbiana, o fluxo de nitrogênio microbiano (N-mic) e nitrogênio não-amoniacal (NNA), com valores médios de 31,8 e 33,9 g de N/kg de MODR; 0,40 e 0,41 g de N/Mcal de EDR; 78,2 e 52,5 g/dia; 89,6 e 76,3 g/dia, respectivamente, para as dietas contendo silagem de milho e feno de tifton. A adição de enzimas fibrolíticas não influenciou os parâmetros ruminais de bovinos alimentados com feno e silagem de milho.

Análise de antenas utilizando substrato cerâmico, zpt, produzido por síntese auto propagante para aplicações em sistemas de micro-ondas

Ceramic substrates have been investigated by researchers around the world and has achieved a high interest in the scientific community, because they had high dielectric constants and excellent performance in the structures employed. Such ceramics result in miniaturized structures with dimensions well reduced and high radiation efficiency. In this work, we have used a new ceramic material called lead zinc titanate in the form of Zn0,8Pb0,2TiO3, capable of being used as a dielectric substrate in the construction of various structures of antennas. The method used in constructing the ceramic combustion synthesis was Self- Sustained High Temperature (SHS - "Self-Propagating High-Temperature Synthesis") which is defined as a process that uses highly exothermic reactions to produce various materials. Once initiated the reaction area in the reaction mixture, the heat generated is sufficient to become self-sustaining combustion in the form of a wave that propagates converting the reaction mixture into the product of interest. Were analyzed aspects of the formation of the composite Zn0,8Pb0,2TiO3 by SHS powders and characterized. The analysis consisted of determining the parameters of the reaction for the formation of the composite, as the ignition temperature and reaction mechanisms. The production of composite Zn0,8Pb0,2TiO3 by SHS performed in the laboratory, was the result of a total control of combustion temperature and after obtaining the powder began the development of ceramics. The product was obtained in the form of regular, alternating layers of porous ceramics and was obtained by uniaxial pressing. 10 The product was characterized by analysis of dilatometry, X-ray diffraction analysis and scanning electron microscopy. One of the contributions typically defined in this work is the development of a new dielectric material, nevertheless presented previously in the literature. Therefore, the structures of the antennas presented in this work consisted of new dielectric ceramics based Zn0,8Pb0,2TiO3 usually used as dielectric substrate. The materials produced were characterized in the microwave range. These are dielectrics with high relative permittivity and low loss tangent. The Ansoft HFSS, commercial program employee, using the finite element method, and was used for analysis of antennas studied in this work

Análise do efeito do tempo da moagem de alta energia no tamanho de cristalito e microdeformação da rede cristalina do WC-Co

Hard metals are the composite developed in 1923 by Karl Schröter, with wide application because high hardness, wear resistance and toughness. It is compound by a brittle phase WC and a ductile phase Co. Mechanical properties of hardmetals are strongly dependent on the microstructure of the WC Co, and additionally affected by the microstructure of WC powders before sintering. An important feature is that the toughness and the hardness increase simultaneously with the refining of WC. Therefore, development of nanostructured WC Co hardmetal has been extensively studied. There are many methods to manufacture WC-Co hard metals, including spraying conversion process, co-precipitation, displacement reaction process, mechanochemical synthesis and high energy ball milling. High energy ball milling is a simple and efficient way of manufacturing the fine powder with nanostructure. In this process, the continuous impacts on the powders promote pronounced changes and the brittle phase is refined until nanometric scale, bring into ductile matrix, and this ductile phase is deformed, re-welded and hardened. The goal of this work was investigate the effects of highenergy milling time in the micro structural changes in the WC-Co particulate composite, particularly in the refinement of the crystallite size and lattice strain. The starting powders were WC (average particle size D50 0.87 μm) supplied by Wolfram, Berglau-u. Hutten - GMBH and Co (average particle size D50 0.93 μm) supplied by H.C.Starck. Mixing 90% WC and 10% Co in planetary ball milling at 2, 10, 20, 50, 70, 100 and 150 hours, BPR 15:1, 400 rpm. The starting powders and the milled particulate composite samples were characterized by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) to identify phases and morphology. The crystallite size and lattice strain were measured by Rietveld s method. This procedure allowed obtaining more precise information about the influence of each one in the microstructure. The results show that high energy milling is efficient manufacturing process of WC-Co composite, and the milling time have great influence in the microstructure of the final particles, crushing and dispersing the finely WC nanometric order in the Co particles

Anodização para obtenção de membranas cerâmicas

This a study on the achievement of alumina membranes by the method of anodizing. From this method got up a layer of aluminum oxide on the anodic metal, who presented the basic properties necessary for the application as a support for the production and acquisition of nanomaterials, such as porosity nano and resistance to high temperature, and other properties, as resistance to corrosion, and chemical, high ranking of the structure and pore size of the pores. The latter, ranging from 10 to 100nm depended on the electrolyte used, which in this study was the H2SO4. To remove all remaining aluminum, it is a bath of dissolution with HCl and CuCl where the residual aluminum has been withdrawn, and the deep pores were opened after chemical treatment with NaOH. After the dissolution, the membranes were calcined at temperatures of 300, 600 and 900° C, and sintered at temperatures of 1200 and 1300º C to win mechanical strength, porosity and observe the desired crystallization. Then went through analyses of composition through X-ray diffraction and morphology of the microstructure through a scanning electron microscope. The method was effective for obtaining alumine membranes applied in the processes of production of materials in nano

Fibras de licuri: um reforço vegetal alternativo de compósitos poliméricos

This research is based, at first, on the seeking of alternatives naturals reinforced in place of polymeric composites, also named reinforced plastics. Therein, this work starts with a whole licuri fiber micro structural characterization, as alternative proposal to polymeric composites. Licuri fiber is abundant on the Bahia state flora, native from a palm tree called Syagrus Coronata (Martius) Beccari. After, it was done only licuri fiber laminar composite developing studies, in order to know its behavior when impregnated with thermofix resin. The composite was developed in laminar structure shape (plate with a single layer of reinforcement) and produced industrially. The layer of reinforcement is a fabric-fiber unidirectional of licuri up in a manual loom. Their structure was made of polyester resin ortofitálica (unsaturated) only reinforced with licuri fibers. Fiber characterization studies were based on physical chemistry properties and their constitution. It was made by tension, scanning electron microscopy (SEM), x-ray diffraction (RDX) and thermal analyses (TG and DTA) tests, besides fiber chemistry analyses. Relating their mechanical properties of strength and hardness testing, they were determined through unit axial tension test and flexion in three points. A study in order to know fiber/matrix interface effects, in the final composites results, was required. To better understand the mechanical behavior of the composite, macroscopic and microscopic optical analysis of the fracture was performed

Estudo do efeito da substituição de caulim por resíduo de caulim na fabricação de cerâmica de revestimento

Companies involved in kaolin mining and treatment represent an important area of industrial development in Brazil, significantly contribution to the worldwide production of such mineral. As a result, large volumes of kaolin residue are constantly generated and abandoned in the environment, negatively contributing to its preservation. In this scenario, the objective of the present study was to characterize the residue generated from kaolin mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Three compositions were prepared using kaolin residue contents of 10%, 20% and 30%. Samples were uniaxially pressed, fired at 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results showed that the residue basically consisted of kaolinite and successfully replaced raw kaolin in the preparation of ceramic title formulations without significantly affecting the properties of the fired material

Utilização de resíduos de rochas ornamentais na produção de cerâmica branca

The marble and granite waste come from the process of mining of those ornamental rocks for use in the building industry. Brazil is one of the largest producers of blocks or finished products of ornamental rocks, extracting about 5.2 tons / year. The largest national producers are the states of Espírito Santo, Minas Gerais and Bahia which account for 80% of the Brazilian production. However, the waste total amount during processing of these blocks reaches 40% of the total. The use of the waste produced by this industry in white ceramics could be a form of disposition, because these materials, are thrownasa mud directly at decantation ponds, wastelands or in rivers, without any treatment. The present work has as main purpose to study the influence that reject of the ornamental rocks on the physical and mechanical properties of white ceramics. X-Ray characterizations of raw materials by were performed X-Ray fluorescence, X-Ray diffraction, granulometric, thermogravimetric and thermodiferencial analysis, five formulations were made (0, 10, 20, 30, 40% in granite weight) wich were burned at three temperatures: 1100°C, 1150°C and 1200ºC with 60 minutes of sorling time. After sintering, the samples were submitted to different analyser absorption of water, linear retraction, apparent porosity, apparent specific mass, flexival stronght, and scanning were obtained microscopy. Compatible technological properties within the limits demanded for the production of porcelainized stoneware

Estudo da oxidação superficial de ligas odontológicas de Ni-Cr em plasma pulsado para uso em restaurações metalocerâmicas

Metal ceramic restorations matches aesthetic and strength, and in your making occurs an interface oxide layer, wetting resulting and atomic and ionic interactions resulting between metal, oxide and porcelain. However, frequent clinical fails occurs in this restoration type, because lost homogeneous deposition oxide layer and lost interface bond. Thus, in this study, thought depositate homogeneous oxide films above Ni-Cr samples surfaces polite previously, at plasma oxide environment. Six samples was oxided at 300 and 400ºC at one hour, and two samples was oxided in a comum chamber at 900ºC, and then were characterized: optical microscopic, electronic microscopic, micro hardness, and X ray difratometry. Colors stripes were observed at six samples plasma oxided and a grey surface those comum oxided, thus like: hardness increase, and several oxides from basic metals (Ni-Cr)

Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards