Cholesterol-Lowering Properties of Whole Cowpea Seed and Its Protein Isolate in Hamsters

Hypercholesterolemic hamsters were fed for 4 wk on diets rich in saturated fatty acids and cholesterol, differing only in protein source (20%): casein (control group, HC), whole cowpea seed (HWS), and cowpea protein isolate (HPI). Hamsters fed on HWS and HPI presented significant reductions in plasma total cholesterol and non-HDL cholesterol. HPI and HC presented similar protein digestibility, which were significantly higher than that of HWS. Animals fed on HWS presented significantly higher levels of bile acids and cholesterol in feces than did the animals fed on casein or HPI diets. Histological analyses of the liver showed that HC diet resulted in steatosis widely distributed throughout the hepatic lobule, while HWS and HPI diets promoted reductions in liver steatosis. The effectiveness of HWS for modulating lipid metabolism was greater than that of HPI, as measured by plasma cholesterol reduction and liver steatosis.

Comparison of Neck Skin Excision and Whole Carcass Rinse Sampling Methods for Microbiological Evaluation of Broiler Carcasses before and after Immersion Chilling

Sampling protocols for detecting Salmonella on poultry differ among various countries. In the United States, the U.S. Department of Agriculture Food Safety and Inspection Service dictates that whole broiler carcasses should be rinsed with 400 ml of 1% buffered peptone water, whereas in the European Union 25-g samples composed of neck skin from three carcasses are evaluated. The purpose of this study was to evaluate a whole carcass rinse (WCR) and a neck skin excision (NS) procedure for Salmonella and Escherichia coli isolation from the same broiler carcass. Carcasses were obtained from three broiler processing plants. The skin around the neck area was aseptically removed and bagged separately from the carcass, and microbiological analysis was performed. The corresponding carcass was bagged and a WCR sample was evaluated. No significant difference (alpha <= 0.05) in Salmonella prevalence was found between the samples processed by the two methods, but both procedures produced many false-negative Salmonella results. Prechill, 37% (66 carcasses), 28% (50 carcasses), and 51% (91 carcasses) of the 180 carcasses examined were positive for Salmonella by WCR, NS, and both procedures combined, respectively. Postchill, 3% (5 carcasses), 7% (12 carcasses), and 10% (17 carcasses) of the 177 carcasses examined were positive for Salmonella by the WCR, NS, and combination of both procedures, respectively. Prechill, E. coli plus coliform counts were 3.0 and 2.6 log CFU/ml by the WCR and NS methods, respectively. Postchill. E. coli plus coliform counts were 1.7 and 1.4 log CFU/ml by the WCR and NS methods, respectively.

Investigation of whole blood of SJL/J mice using neutron activation analysis

The Br (0.0022 +/- A 0.0006 gL(-1)), Ca (0.113 +/- A 0.012 gL(-1)), Cl (3.07 +/- A 0.36 gL(-1)), K (2.63 +/- A 0.14 gL(-1)), Mg (0.045 +/- A 0.002 gL(-1)) and Na (2.09 +/- A 0.10 gL(-1)) concentrations were determined in whole blood of SJL/J mice using the Neutron Activation Analysis (NAA) technique. Eleven whole blood samples were analyzed in the IEA-R1 nuclear reactor at IPEN (So Paulo, Brazil). These data contribute for applications in veterinary medicine related to biochemistry analyses using whole blood. Moreover, the correlation with human blood estimation allows to checking the similarities for studying muscular dystrophy using this model animal.

Chemoselective screening for the reduction of a chiral functionalised (+/-)-2-(phenylthio)cyclohexanone by whole cells of Brazilian micro-organisms

The use of whole cells of micro-organisms to bring about the biotransformation of an organic compound offers a number of advantages, but problems caused by enzymatic Promiscuity may be encountered upon With Substrates hearing more than one functional group. A one-pot screening method, in which whole fungal cells were incubated with a Mixture of 4-rnethylcyclohexanone I and phenyl methyl Sulfide 2, has been employed to determine the chemoselectivity of various biocatalysts. The hyphomycetes, Aspergillus terreus CCT 3320 and A. terreus URM 3571, catalysed the oxidation of 2 accompanied by the reduction of I to 4-methylcyclohexanol 1a and, for strain A. terreus CCT 3320, the Baeyer-Villiger oxidation of 1. The Basidomycetes, Trametes versicolor CCB 202, Pycnoporus sanguineus CCB 501 and Trichaptum byssogenum CCB 203, catalysed the oxidation of 2 and the reduction 1, but no Baeyer-Villiger reaction products were detected. In contrast. Trametes rigida CCB 285 catalysed the biotransformation of 1 to 1a, exclusively, in the absence of any detectable Sulfide oxidation reactions. The chemoselective reduction Of (+/-)-2-(phenylthio)cyclohexanone 3 by T. rigida CCB 285 afforded exclusively the (+)-cis-(1R,2S) and (+)-trans-(1S,2S) diastereoisomers of 2-(phenylthio)cyclohexan-1-ol 3a in moderate yields (13% and 27%, respectively) and high enantiomeric excesses (>98%). Chemoselective screening for the reduction of a ketone and/or the oxidation Of a Sulfide group in one pot by whole cells of micro-organisms represents an attractive technique with applications in the development of synthesis of complex molecule hearing different functional groups. (C) 2008 Published by Elsevier Ltd.

Bioreduction of alpha-chloroacetophenone by whole cells of marine fungi

The asymmetric reduction of 2-chloro-1-phenylethanone (1) by seven strains of marine fungi was evaluated and afforded (S)-(-)-2-chloro-1-phenylethanol with, in the best case, an enantiomeric excess of 50% and an isolated yield of 60%. The ability of marine fungi to catalyse the reduction was directly dependent on growth in artificial sea water-based medium containing a high concentration of Cl(-) (1.2 M). When fungi were grown in the absence of artificial sea water, no reduction of 1 by whole cells was observed. The biocatalytic reduction of 1 was more efficient at neutral rather than acidic pH values and in the absence of glucose as co-substrate.

Dynamic whole system testing of combined renewable heating systems : the current state of the art

Objective: For the evaluation of the energetic performance of combined renewable heating systems that supply space heat and domestic hot water for single family houses, dynamic behaviour, component interactions, and control of the system play a crucial role and should be included in test methods. Methods: New dynamic whole system test methods were developed based on “hardware in the loop” concepts. Three similar approaches are described and their differences are discussed. The methods were applied for testing solar thermal systems in combination with fossil fuel boilers (heating oil and natural gas), biomass boilers, and/or heat pumps. Results: All three methods were able to show the performance of combined heating systems under transient operating conditions. The methods often detected unexpected behaviour of the tested system that cannot be detected based on steady state performance tests that are usually applied to single components. Conclusion: Further work will be needed to harmonize the different test methods in order to reach comparable results between the different laboratories. Practice implications: A harmonized approach for whole system tests may lead to new test standards and improve the accuracy of performance prediction as well as reduce the need for field tests.

Testing of combined heating systems for small houses: Improved procedures for whole system test methods : Deliverable 2.3

Dynamic system test methods for heating systems were developed and applied by the institutes SERC and SP from Sweden, INES from France and SPF from Switzerland already before the MacSheep project started. These test methods followed the same principle: a complete heating system – including heat generators, storage, control etc., is installed on the test rig; the test rig software and hardware simulates and emulates the heat load for space heating and domestic hot water of a single family house, while the unit under test has to act autonomously to cover the heat demand during a representative test cycle. Within the work package 2 of the MacSheep project these similar – but different – test methods were harmonized and improved. The work undertaken includes:  • Harmonization of the physical boundaries of the unit under test. • Harmonization of the boundary conditions of climate and load. • Definition of an approach to reach identical space heat load in combination with an autonomous control of the space heat distribution by the unit under test. • Derivation and validation of new six day and a twelve day test profiles for direct extrapolation of test results.   The new harmonized test method combines the advantages of the different methods that existed before the MacSheep project. The new method is a benchmark test, which means that the load for space heating and domestic hot water preparation will be identical for all tested systems, and that the result is representative for the performance of the system over a whole year. Thus, no modelling and simulation of the tested system is needed in order to obtain the benchmark results for a yearly cycle. The method is thus also applicable to products for which simulation models are not available yet. Some of the advantages of the new whole system test method and performance rating compared to the testing and energy rating of single components are:  • Interaction between the different components of a heating system, e.g. storage, solar collector circuit, heat pump, control, etc. are included and evaluated in this test. • Dynamic effects are included and influence the result just as they influence the annual performance in the field. • Heat losses are influencing the results in a more realistic way, since they are evaluated under "real installed" and representative part-load conditions rather than under single component steady state conditions.   The described method is also suited for the development process of new systems, where it replaces time-consuming and costly field testing with the advantage of a higher accuracy of the measured data (compared to the typically used measurement equipment in field tests) and identical, thus comparable boundary conditions. Thus, the method can be used for system optimization in the test bench under realistic operative conditions, i.e. under relevant operating environment in the lab.   This report describes the physical boundaries of the tested systems, as well as the test procedures and the requirements for both the unit under test and the test facility. The new six day and twelve day test profiles are also described as are the validation results.

Knowledge translation in Uganda : a qualitative study of Ugandan midwives' and managers' perceived relevance of the sub-elements of the context cornerstone in the PARIHS framework

BACKGROUND: A large proportion of the annual 3.3 million neonatal deaths could be averted if there was a high uptake of basic evidence-based practices. In order to overcome this 'know-do' gap, there is an urgent need for in-depth understanding of knowledge translation (KT). A major factor to consider in the successful translation of knowledge into practice is the influence of organizational context. A theoretical framework highlighting this process is Promoting Action on Research Implementation in Health Services (PARIHS). However, research linked to this framework has almost exclusively been conducted in high-income countries. Therefore, the objective of this study was to examine the perceived relevance of the subelements of the organizational context cornerstone of the PARIHS framework, and also whether other factors in the organizational context were perceived to influence KT in a specific low-income setting. METHODS: This qualitative study was conducted in a district of Uganda, where focus group discussions and semi-structured interviews were conducted with midwives (n = 18) and managers (n = 5) within the catchment area of the general hospital. The interview guide was developed based on the context sub-elements in the PARIHS framework (receptive context, culture, leadership, and evaluation). Interviews were transcribed verbatim, followed by directed content analysis of the data. RESULTS: The sub-elements of organizational context in the PARIHS framework--i.e., receptive context, culture, leadership, and evaluation--also appear to be relevant in a low-income setting like Uganda, but there are additional factors to consider. Access to resources, commitment and informal payment, and community involvement were all perceived to play important roles for successful KT. CONCLUSIONS: In further development of the context assessment tool, assessing factors for successful implementation of evidence in low-income settings--resources, community involvement, and commitment and informal payment--should be considered for inclusion. For low-income settings, resources are of significant importance, and might be considered as a separate subelement of the PARIHS framework as a whole.

Multivariate modelling of landuse on in-stream salinity over multiple spatial scales

An impediment to sustainable dryland salinity management is the lack of information on contributing factors. GIS and satellite imagery now offer a cost-effective means of generating relevant land and water resource information for integrated regional management of salinity. In this paper the relationships between patterns in land uselcover distribution and base flow salt concentration in streams (indicated by EC) are investigated and modelled. The Glenelg-Hopkins area is a large regional watershed in southwest Victoria, Australia, covering approximately 2.6 million ha. It is currently estimated that 27,400 ha of land is affected by dryland salinity and this is predicted to rapidly increase in the next decade' if current conditions prevail. Salt concentration data from five gauging stations were analysed with multi-temporal land use maps obtained from satellite imagery. Multiple regression analyses demonstrated that the variables Native Vegetation and Dry/and Grain Cropping were the most significant influences on in~stream salinity in the whole catchment (1=88.9%) and 500 m V=88.3%) and 100 m riparian buffers (1=86.9%) during times of base flow. The implications for future land use planning, effectiveness of riparian zones and revegetation programmes is discussed. This work also demonstrates the utility of applying nmltivariate statistical analyses, spatial statistics, and remote sensing with data integrated in a GIS framework for the purpose of predicting and managing the regional salinity threat.

Spatial analysis of urban stormwater quality

Urban stormwater non-point source pollutants are recognized as a major cause of receiving waters quality deterioration. To date most research has focused on specifying temporal variations of stormwater quality parameters which includes high uncertainties and also increases the risk of pollution control structures failure. Traditionally, the temporal variations of quality parameters in forms of either pollutograph or Event Mean Concentration (EMC) is obtained by sampling stormwater at the outlet of urban catchments for quality analysis in addition to measurement of flow rate over years. Spatial variations of the runoff quality are the key factor in non-point source pollution studies. This research investigates spatial variability of urban runoff quality parameters such as Total Phosphorous (TP), Total Nitrogen (TN), Suspended Solids (SS) and Biochemical Oxygen Demands (BOD) in relation to land use of urban catchments. In spatial analysis, stormwater will be sampled over the whole catchment area for a number of rainfall events during a year without any requirement to measure flow rate. This research showed comparable results for average pollutant concentrations with those of other urban catchments in Australia where traditional sampling method was used. The research outcomes will reliably estimate pollutants concentration for improved and efficient design of pollution control structures for each land use.

In vitro carbohydrate digestibility of whole-chickpea and chickpea bread products

Pulses such as the chickpea are generally considered to be valuable dietary sources of slowly digestible starch, a form of starch that is considered beneficial to health since it results in relatively low post-meal blood glucose levels compared with more rapidly digested starch. The development of novel chickpea-based foods is necessary to help expand the worldwide consumption of the chickpea. However, the effect of different processing methods on the starch digestibility of chickpea-based foods has not been widely investigated. This study used an in vitro method simulating human carbohydrate digestion to determine levels of slowly digestible starch, rapidly digestible starch (RDS), resistant starch, total starch and rapidly available glucose (RAG) of: (i) whole-chickpea products (domestically boiled, commercially canned and commercially precooked/vacuum-packaged); and (ii) standard white bread, chickpea flour bread (25% replacement of wheat flour by chickpea flour) and extruded chickpea flour bread (25% replacement of wheat flour by extruded chickpea flour). The RAG levels were then used to predict the relative in vivo glycaemic indices of the products. The commercially precooked/vacuum-packaged whole chickpeas demonstrated higher levels of RDS than the commercially canned and domestically boiled products (P<0.05). In addition, the domestically boiled product had lower levels of RAG (g/100 g available carbohydrate) compared with the canned and precooked/vacuum-packaged products (P<0.05). There were no significant differences between any of the carbohydrate digestibility measures of the white bread, chickpea flour bread and extruded chickpea flour bread (P>0.05) and all bread products demonstrated far higher RAG (g/100 g available carbohydrate) values than the whole-chickpea products. The findings suggest that the commercially precooked/vacuum-packaged whole chickpeas and the canned product may have higher and less beneficial glycaemic indices than the domestically boiled chickpeas. It appears unlikely that the use of chickpea flour or extruded chickpea flour, at the incorporation rate investigated in this study, would modify the glycaemic index of bread. It is probable, however, that the chickpea bread products investigated would demonstrate higher and potentially less beneficial glycaemic indices than the whole-chickpea products.

Evaluation of SWAT for modelling the water balance of the Woady Yaloak River catchment, Victoria

Future land use change will have a profound effect on the water balance of agricultural and rural catchments in Australia. It is therefore imperative that any such consequences likely to arise from impending land use changes are predicted accurately so that strategies can be implemented to minimise or prevent undesirable impacts to the water balance of catchments. SWAT is a comprehensive hydrologic model developed to predict the impacts of land use change on water balance. SWAT has been applied in Australia but it has not yet been widely adopted. The application of SWAT to the Woady Yaloak River catchment in southwest Victoria is described in this paper. SWAT is being evaluated to determine whether it is suitable for modelling the water balance of catchments in the southwest region of Victoria and to determine if it could be adopted as a planning tool to manage land use change. The results achieved in this initial application of SWAT were very pleasing. However it is shown that the groundwater and tree growth components of the model are not entirely adequate. These shortcomings with SWAT affect its ability to accurately model the water balance of catchments in Australia. It is recommended that both these components be modified to improve model performance.