Evaluation of cutting patterns produced in primary teeth by an air-abrasion system

Objective: the aim of this in vitro study was to assess the effect of tip diameter, nozzle distance, and application time of an air-abrasion system for cavity preparation on the enamel of primary teeth. Method and materials: Forty exfoliated primary teeth were air abraded with a microabrasion machine used with a handpiece with an 80-degree-angle nozzle, 50-mum abrasive particle size, and 80-psi air pressure. The effects of 0.38- or 0.48-mm inner tip diameter, 2- or 5-mm distance from tip to tooth surface, and 15 or 30 seconds of application time on cutting efficiency were evaluated. Cutting width and depth were analyzed and measured from scanning electron micrographs. Results: Statistical analysis revealed that the width of the cuts was significantly greater when the tip distance was increased. Significantly deeper cavities were produced by a tip with a 0.48-mm inner diameter. The application time did not influence the cuts. Conclusion: the cutting patterns found in this study suggest that precise removal of enamel in primary teeth is best accomplished when a tip with a 0.38-mm inner diameter is used at a 2-mm distance.

BIOSENSORS FOR GLUCOSE NEEDLE-SHAPED FOR IN-VIVO MONITORING

Different procedures for obtaining a needle biosensor for the determination of glucose to be inserted subcutaneously in vivo, have been compared. Platinum wires with a diameter of 75 mum, teflon-coated were inserted in hypodermic needles and fixed with a two-component epoxy resin. Using a dip-coating procedure, several layers were deposited on electrodes. The first coating was cellulose acetate, the second was immobilized glucose oxidase (GOD) mixed with bovine serum albumin (BSA) and glutaraldheyde, the third coating was a polyurethane coating obtained with commercially available products. A large number of electrodes have been tried and statistically evaluated but they seem to be affected by poor reproducibility evidenced by a large spreading in successive calibration curves. Then, the polyurethane coating has been replaced by a thin polycarbonate membrane salinized and fixed on the tip of the needle. Reproducible results were achieved and first results of in vivo measurements on rabbits are reported.

Determination of olive oil acidity by CE

In this work, a CE method for the determination of olive oil acidity was proposed. The method was based on an ethanolic extraction (at 60 degrees C) of the oil long-chain free fatty acids (LC-FFAs) components followed by CE determination in pH 6.86 phosphate buffer at 15 mmol/L concentration containing 4 mmol/L sodium dodecylbenzenesulfonate (SDBS), 10 mmol/L polyoxyethylene 23 lauryl ether (Brij 35((R))), 2% v/v 1-octanol and 45% v/v ACN under indirect UV detection at 224 nm. Although this electrolyte promoted baseline separation of myristic acid (C14:0) (internal standard (IS)) and olive oil major components (palmitic acid (C16:0), oleic acid (C18:1c) and linoleic acid (C18:2cc)) in less than 8 min, after a few injections, the electropherogram profiles were severely altered (peak broadening, migration time shifts, etc.) and the current increased substantially. An adsorption study was conducted revealing that the dissolution of the capillary external polyimide coating during the electrophoretic run caused the detrimental effect. After removal of the capillary tip coating, ten consecutive injections could be performed without any disturbances and this simple procedure was, therefore, implemented during quantitative purposes. The reliability of the proposed method was further investigated by the determination of acidity of an extra virgin olive oil sample in comparison to the established methodology (AOCS method Ca 5a40, alkaline volumetric titration (AVT)). No statistical differences were found within 95% confidence level. A % acidity of 0.39 +/- 0.02 was found for the olive oil sample under consideration.

A well-balanced flow equation for noise removal and edge detection

In this paper, an anisotropic nonlinear diffusion equation for image restoration is presented. The model has two terms: the diffusion and the forcing term. The balance between these terms is made in a selective way, in which boundary points and interior points of the objects that make up the image are treated differently. The optimal smoothing time concept, which allows for finding the ideal stop time for the evolution of the partial differential equation is also proposed. Numerical results show the proposed model's high performance.

Evaluation of dental pulp repair using low level laser therapy (688 nm and 785 nm) morphologic study in capuchin monkeys

The aim of this study was to evaluate the hypothesis that low-level laser therapy (LLLT) 688 nm and 785 nm accelerate dentin barrier formation and repair process after traumatic pulp exposure. The sample consisted of 45 premolars of capuchin monkeys (Cebus apella) with pulp exposure Class V cavities. All premolars were treated with calcium hydroxide (Ca(OH)(2)), divided in groups of 15 teeth each, and analyzed on 7(th), 25(th), and 60(th) day. Group GI - only Ca(OH)(2), GIF- laser 688 nm, and GIII - laser 785 nm. Laser beam was used in single and punctual dose with the parameters: continuous, 688 nm and 785 nm wavelength, tip's area of 0.00785 cm(2), power 50 mW, application time 20 s, dose 255 J/cm(2), energy 2 J. Teeth were capped with Ca(OH)(2), Ca(OH)(2) cement and restored with amalgam. All groups presented pulp repair. on 25(th) day the thickness of the formed dentin barrier was different between the groups GI and GII (p < 0.05) and between groups GI and GIII (p < 0.01). on 60(th) day there was difference between GI and GIII (p < 0.01). It may be concluded that, LLLT 688 nm and 785 nm accelerated dentin barrier formation and consequently pulp repair process, with best results using infrared laser 785 nm. (c) 2009 by Astro Ltd. Published exclusively by WLLEY-VCH Verlag GmbH & Co. KGaA

ARE CORPORAL ALLOMETRIC MEASUREMENTS GOOD PREDICTORS of PALATABILITY IN NEOTROPICAL BUTTERFLIES (LEPIDOPTERA)?

Since palatable butterflies are more dependent on evasive flight to escape from predators, they should be more restricted in their flight-related morphology than unpalatable ones. We compared: the ratios between the (1) length of head plus thorax and the length of abdomen (A/B), (2) length of the tip of the head to wing base and the length of the wing base to end of the abdomen (C/D), (3) the variances of A/B and C/D, (4) the proportion between the thoracic and the body weight, and (5) the flight speed between palatable and unpalatable butterflies. A/B and thoracic/body weight were higher for palatable species, indicating higher body symmetry and muscular mass. However, flight speed did not differ. Unexpectedly, the variance of A/B was higher for palatable species while that of C/D did not differ. Therefore, corporal allometric measurements of Neotropical butterflies are good predictors of palatability, though not of flight speed.

Nanomechanical properties of glass-ceramic films obtained by pressure impregnation of oxide powders on commercial float glass surfaces

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Tratamento endurecedor para cones de guta-percha.

The subject of this work was to study a hardening procedure for gutta-percha points, in order to make ease their introduction in very curved root canals. Gutta-percha points of different brands and dimensions were submitted to treatment with alcohol 96 degrees for 1 to 3 days. After this treatment the weight necessary to make a bending of 35 degrees on the tip of the gutta-percha was evaluated. The obtained results were submitted to statistic analysis and the following conclusions can be observed: a. The treatment with alcohol make hard the gutta-percha points in a significant level. b. There was not significant differences between the results obtained with more than one day of alcohol treatment. c. The treatment with alcohol do not make hard all the brands of gutta-percha points.

Dilatacao pneumatica no megaesofago avancado. Resultados do sequimento tardio

Six patients with advanced Chagas' megaesophagus with poor condition for surgical indication due to severe malnutrition and concomitant diseases were submitted to pneumatic dilatation with the aid of the endoscope. The method consists in leading the tip of the pneumatic dilatator into the cardia with the tip of the endoscope. Insufflation of the balloon must be slow and progressive with visualization of the mucosa of the cardia after insufflating of 2 pounds of air pressure. An excellent symptomatic relief was seen in the five-year follow-up but without improvement in the degree of the esophageal dilatation.

Systematic vegetative anatomy and ensiform leaf development in Xyris (Xyridaceae)

Ensiform leaf development in monocotyledons follows a broadly similar sequence in a wide range of relatively unrelated taxa, indicating a plastic developmental pattern, possibly associated with stressed environmental conditions, since Xyris species tend to grow in relatively damp but nutrient-poor environments. The bifacial leaf sheath surrounds the apex and the subadjacent primordium. A conical unifacial leaf tip 'Vorlauferspitze' is established at an early stage, followed by extension growth in the region behind it, generating a unifacial ensiform blade. Root and rhizome structure are also described in a systematic context, particularly in comparison with related taxa in Xyridaceae and other commelinoid monocotyledons, although information on these structure is relatively sparse.

New species of Hemiodus (ostariophysi, characiformes, hemiodontidae) from the Rio Tocantins, Brazil, with comments on color patterns and tooth shapes within the species and genus

A new hemiodontid species, Hemiodus tocantinensis, is described from the rio Tocantins, Amazon basin, Brazil. It is most closely related to H. ternezi and H. thayeria based on the presence of a dark longitudinal stripe extending from behind the eye or the opercle to the tip of lower caudal fin lobe but is distinguished by the possession of 51 to 58 perforated lateral line scales and an oblique dark blotch on the dorsal fin extending from its anterior distal portion through the middle basal portion of the fin. The evolution of color patterns and tooth shapes present in the Hemiodus species is commented.

Aspects of IFP for citrus production in Brazil

Brazilian citriculture represents about 25% of the total world citrus production with an area of 851,518 ha and a total production of more than 17 million tons in 1996. Besides its importance to the brazilian economy, represented by more than 1 billion US $ by year from FCOJ exportation, the citriculture has problems related to low productivity, due to several cultural practices and management. The productivity would be improved by an IFP system. The main problems are related to soil, as poor conservation, use of poor drained soils and bad preparation for planting; diseases-canker, CVC, leprosis, Phytophtora gummosis and other fungus diseases; pests - mites, scales, nematodes and others; the use of disease free and improved scion and rootstocks propagative material is usual; cultural practices - as nutrition, irrigation, wind breaks, weed control, pruning, replant and others, as density planting could be improved. Some possible solutions will be discussed for improving the brazilian citrus productivity and quality by IFP, based on research made.

Avaliação de seis variedades de uvas sem sementes no Submédio São Francisco

This work aimed to study aspects related to vegetative and productive development of plants and characteristics and chemical components of bunches of six seedless grape varieties at environmental conditions of São Francisco river's valley, Northeastern Brazil. The experiment was carried out during 1997 and 1998. The varieties tested were grafted on IAC 572 ('Jales') rootstock. The experimental model utilized was totally randomized, and with parcels subdivided into different production cycles. The results showed significative differences among varieties at different pruning times. The average weight of bunches varied from 164.8 g for 'Marroo Seedless' and 203.5 g for 'Beauty Seedless'. The average diameter of berries was superior to 15.7 mm for all of the varieties. The total soluble solids varied from 14.05°Brix in 'Canner' to 19.6°Brix in 'Venus'. The total titratable acidity (ATT) was lower than 0.91 g tartaric acid/100 mL of juice. The ratio SST/ATT varied from 19.05 in 'Beauty Seedless' to 28.57 in 'Vênus'. 'Vênus' and 'Marroo Seedless' were the most productive varieties, with the average annual production of 24 ton/ha and 20 ton/ha, respectively.

Características da pulverização produzida por pontas Yamaho da série 'D'

This study evaluated the characteristics of spray produced by Yamaho nozzle tip'D'series. The droplet size of nozzle tips D3, D4, D5, D6 and D8 were evaluated at 703, 1.050, 1.406, 1.758, 2.110, 2.461 e 2.813 kPa pressures (100, 200, 250; 350, e 400 psi) by means of laser equipment, as well as the flow rate of nozzle tip at the pressures of 702, 1.125, 1.406, 1.828, 2.110, 2.532 e 2.813 kPa (100, 160, 200, 260,300; 360 e 400 psi) which were compared with values indicated by manufacturer. The droplet produced at all pressures presented a very fine spray, which in agriculture may promote losses by evaporation and drift. For all nozzle tips, except D8 in pressures 1.828, 2.532 e 2.813 kPa, the difference between the observed flow rate indicated by the manufacturer was higher than 5%. The paper demonstrates that the nozzle tip tested, in spite of not having uniform flow rate, may promote the contamination of spray operator and environment due to the droplet spectrum produced.

Mutagenic potential evaluation of the water of a river that receives tannery effluent using the Allium cepa test system

Several studies are being conducted to assess the toxicity and cytotoxicity of water bodies receiving industrial and domestic effluents, using the Allium cepa test. To assess the toxicity and mutagenicity of water possibly contaminated with chromium, derived from tannery activities, seasonal water samplings were performed in 2001 and 2002 at five different sites along the Sapucaizinho river, Municipality of Patrocinio Paulista, State of São Paulo, Brazil. A. cepa seeds were used as the test material and were submitted to germination in waters from the different collection sites, in Milli-Q water (negative control) and in aqueous solution of chromium (positive control). For the determination of cell division rates and mitotic irregularities, slides were prepared with root tip cells according to the standard Feulgen methodology. The results showed that the collection sites most heavily compromised by chromium emission presented low mitotic indices and a higher frequency of mitotic changes such as irregular anaphases (disorganized, multipolar, laggard), cells with chromosomal adherences, cells with micronuclei, and binucleate and/or multinucleate cells. © 2004 The Japan Mendel Society.