A robust numerical framework to the analysis of material failure of fibre reinforced soft tissue

In this work, robustness and stability of continuum damage models applied to material failure in soft tissues are addressed. In the implicit damage models equipped with softening, the presence of negative eigenvalues in the tangent elemental matrix degrades the condition number of the global matrix, leading to a reduction of the computational performance of the numerical model. Two strategies have been adapted from literature to improve the aforementioned computational performance degradation: the IMPL-EX integration scheme [Oliver,2006], which renders the elemental matrix contribution definite positive, and arclength-type continuation methods [Carrera,1994], which allow to capture the unstable softening branch in brittle ruptures. The IMPL-EX integration scheme has as a major drawback the need to use small time steps to keep numerical error below an acceptable value. A convergence study, limiting the maximum allowed increment of internal variables in the damage model, is presented. Finally, numerical simulation of failure problems with fibre reinforced materials illustrates the performance of the adopted methodology.

A robust procedure for damage detection from strain measurements based on principal component analysis

FBGs are excellent strain sensors, because of its low size and multiplexing capability. Tens to hundred of sensors may be embedded into a structure, as it has already been demonstrated. Nevertheless, they only afford strain measurements at local points, so unless the damage affects the strain readings in a distinguishable manner, damage will go undetected. This paper show the experimental results obtained on the wing of a UAV, instrumented with 32 FBGs, before and after small damages were introduced. The PCA algorithm was able to distinguish the damage cases, even for small cracks. Principal Component Analysis (PCA) is a technique of multivariable analysis to reduce a complex data set to a lower dimension and reveal some hidden patterns that underlie.

Robust rolling stock under uncertain demand in rapid transit networks

This paper focuses on the railway rolling stock circulation problem in rapid transit networks where the known demand and train schedule must be met by a given fleet. In rapid transit networks the frequencies are high and distances are relatively short. Although the distances are not very large, service times are high due to the large number of intermediate stops required to allow proper passenger flow. The previous circumstances and the reduced capacity of the depot stations and that the rolling stock is shared between the different lines, force the introduction of empty trains and a careful control on shunting operation. In practice the future demand is generally unknown and the decisions must be based on uncertain forecast. We have developed a stochastic rolling stock formulation of the problem. The computational experiments were developed using a commercial line of the Madrid suburban rail network operated by RENFE (The main Spanish operator of suburban trains of passengers). Comparing the results obtained by deterministic scenarios and stochastic approach some useful conclusions may be obtained.

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

Robust control of underactuated wheeled mobile manipulators using GPI disturbance observers

This article describes the design of a linear observer–linear controller-based robust output feedback scheme for output reference trajectory tracking tasks in the case of nonlinear, multivariable, nonholonomic underactuated mobile manipulators. The proposed linear feedback scheme is based on the use of a classical linear feedback controller and suitably extended, high-gain, linear Generalized Proportional Integral (GPI) observers, thus aiding the linear feedback controllers to provide an accurate simultaneous estimation of each flat output associated phase variables and of the exogenous and perturbation inputs. This information is used in the proposed feedback controller in (a) approximate, yet close, cancelations, as lumped unstructured time-varying terms, of the influence of the highly coupled nonlinearities, and (b) the devising of proper linear output feedback control laws based on the approximate estimates of the string of phase variables associated with the flat outputs simultaneously provided by the disturbance observers. Simulations reveal the effectiveness of the proposed approach.

Hardening digital systems with distributed functionality: robust networks

Collaborative hardening and hardware redundancy are nowadays the most interesting solutions in terms of fault tolerance achieved and low extra cost imposed to the project budget. Thanks to the powerful and cheap digital devices that are available in the market, extra processing capabilities can be used for redundant tasks, not only in early data processing (sensed data) but also in routing and interfacing1

Traffic sign detection and tracking using robust 3D analysis

In this paper we present an innovative technique to tackle the problem of automatic road sign detection and tracking using an on-board stereo camera. It involves a continuous 3D analysis of the road sign during the whole tracking process. Firstly, a color and appearance based model is applied to generate road sign candidates in both stereo images. A sparse disparity map between the left and right images is then created for each candidate by using contour-based and SURF-based matching in the far and short range, respectively. Once the map has been computed, the correspondences are back-projected to generate a cloud of 3D points, and the best-fit plane is computed through RANSAC, ensuring robustness to outliers. Temporal consistency is enforced by means of a Kalman filter, which exploits the intrinsic smoothness of the 3D camera motion in traffic environments. Additionally, the estimation of the plane allows to correct deformations due to perspective, thus easing further sign classification.

Robust thermal face recognition using region classifiers

This paper presents a robust approach for recognition of thermal face images based on decision level fusion of 34 different region classifiers. The region classifiers concentrate on local variations. They use singular value decomposition (SVD) for feature extraction. Fusion of decisions of the region classifier is done by using majority voting technique. The algorithm is tolerant against false exclusion of thermal information produced by the presence of inconsistent distribution of temperature statistics which generally make the identification process difficult. The algorithm is extensively evaluated on UGC-JU thermal face database, and Terravic facial infrared database and the recognition performance are found to be 95.83% and 100%, respectively. A comparative study has also been made with the existing works in the literature.

Robust fabrication of electrospun-like polymer mats to direct cell bahaviour

Currently, cell culture systems that include nanoscale topography are widely used in order to provide cells additional cues closer to the in vivo environment, seeking to mimic the natural extracellular matrix. Electrospinning is one of the most common techniques to produce nano fiber mats. However, since many sensitive parameters play an important role in the process, a lack of reproducibility is a major drawback. Here we present a simple and robust methodology to prepare reproducible electrospun-like samples. It consists of a polydimethylsiloxane mold reproducing the fiber pattern to solvent-cast a polymer solution and obtain the final sample. To validate this methodology, poly(L-lactic) acid (PLLA) samples were obtained and, after characterisation, bioactivity and ability to direct cell response were assessed. C2C12 myoblasts developed focal adhesions on the electrospun-like fibers and, when cultured under myogenic differentiation conditions, similar differentiation levels to electrospun PLLA fibers were obtained.

Robust Image Registration with Global Intensity Transformation

This paper presents a registration method for images with global illumination variations. The method is based on a joint iterative optimization (geometric and photometric) of the L1 norm of the intensity error. Two strategies are compared to directly find the appropriate intensity transformation within each iteration: histogram specification and the solution obtained by analyzing the necessary optimality conditions. Such strategies reduce the search space of the joint optimization to that of the geometric transformation between the images.

Online Learning-based Robust Visual Tracking for Autonomous Landing of Unmanned Aerial Vehicles

Autonomous landing is a challenging and important technology for both military and civilian applications of Unmanned Aerial Vehicles (UAVs). In this paper, we present a novel online adaptive visual tracking algorithm for UAVs to land on an arbitrary field (that can be used as the helipad) autonomously at real-time frame rates of more than twenty frames per second. The integration of low-dimensional subspace representation method, online incremental learning approach and hierarchical tracking strategy allows the autolanding task to overcome the problems generated by the challenging situations such as significant appearance change, variant surrounding illumination, partial helipad occlusion, rapid pose variation, onboard mechanical vibration (no video stabilization), low computational capacity and delayed information communication between UAV and Ground Control Station (GCS). The tracking performance of this presented algorithm is evaluated with aerial images from real autolanding flights using manually- labelled ground truth database. The evaluation results show that this new algorithm is highly robust to track the helipad and accurate enough for closing the vision-based control loop.

Robust Real-time Vision-based Aircraft Tracking From Unmanned Aerial Vehicles.

Aircraft tracking plays a key and important role in the Sense-and-Avoid system of Unmanned Aerial Vehicles (UAVs). This paper presents a novel robust visual tracking algorithm for UAVs in the midair to track an arbitrary aircraft at real-time frame rates, together with a unique evaluation system. This visual algorithm mainly consists of adaptive discriminative visual tracking method, Multiple-Instance (MI) learning approach, Multiple-Classifier (MC) voting mechanism and Multiple-Resolution (MR) representation strategy, that is called Adaptive M3 tracker, i.e. AM3. In this tracker, the importance of test sample has been integrated to improve the tracking stability, accuracy and real-time performances. The experimental results show that this algorithm is more robust, efficient and accurate against the existing state-of-art trackers, overcoming the problems generated by the challenging situations such as obvious appearance change, variant surrounding illumination, partial aircraft occlusion, blur motion, rapid pose variation and onboard mechanical vibration, low computation capacity and delayed information communication between UAVs and Ground Station (GS). To our best knowledge, this is the first work to present this tracker for solving online learning and tracking freewill aircraft/intruder in the UAVs.

Online Learning-based Robust Visual Tracking for Autonomous Landing of Unmanned Aerial Vehicles

Autonomous landing is a challenging and important technology for both military and civilian applications of Unmanned Aerial Vehicles (UAVs). In this paper, we present a novel online adaptive visual tracking algorithm for UAVs to land on an arbitrary field (that can be used as the helipad) autonomously at real-time frame rates of more than twenty frames per second. The integration of low-dimensional subspace representation method, online incremental learning approach and hierarchical tracking strategy allows the autolanding task to overcome the problems generated by the challenging situations such as significant appearance change, variant surrounding illumination, partial helipad occlusion, rapid pose variation, onboard mechanical vibration (no video stabilization), low computational capacity and delayed information communication between UAV and Ground Control Station (GCS). The tracking performance of this presented algorithm is evaluated with aerial images from real autolanding flights using manually- labelled ground truth database. The evaluation results show that this new algorithm is highly robust to track the helipad and accurate enough for closing the vision-based control loop.

A methodology to analyze, design and implement very fast and robust controls of Buck-type converters

La electrónica digital moderna presenta un desafío a los diseñadores de sistemas de potencia. El creciente alto rendimiento de microprocesadores, FPGAs y ASICs necesitan sistemas de alimentación que cumplan con requirimientos dinámicos y estáticos muy estrictos. Específicamente, estas alimentaciones son convertidores DC-DC de baja tensión y alta corriente que necesitan ser diseñados para tener un pequeño rizado de tensión y una pequeña desviación de tensión de salida bajo transitorios de carga de una alta pendiente. Además, dependiendo de la aplicación, se necesita cumplir con otros requerimientos tal y como proveer a la carga con ”Escalado dinámico de tensión”, donde el convertidor necesitar cambiar su tensión de salida tan rápidamente posible sin sobreoscilaciones, o ”Posicionado Adaptativo de la Tensión” donde la tensión de salida se reduce ligeramente cuanto más grande sea la potencia de salida. Por supuesto, desde el punto de vista de la industria, las figuras de mérito de estos convertidores son el coste, la eficiencia y el tamaño/peso. Idealmente, la industria necesita un convertidor que es más barato, más eficiente, más pequeño y que aún así cumpla con los requerimienos dinámicos de la aplicación. En este contexto, varios enfoques para mejorar la figuras de mérito de estos convertidores se han seguido por la industria y la academia tales como mejorar la topología del convertidor, mejorar la tecnología de semiconducores y mejorar el control. En efecto, el control es una parte fundamental en estas aplicaciones ya que un control muy rápido hace que sea más fácil que una determinada topología cumpla con los estrictos requerimientos dinámicos y, consecuentemente, le da al diseñador un margen de libertar más amplio para mejorar el coste, la eficiencia y/o el tamaño del sistema de potencia. En esta tesis, se investiga cómo diseñar e implementar controles muy rápidos para el convertidor tipo Buck. En esta tesis se demuestra que medir la tensión de salida es todo lo que se necesita para lograr una respuesta casi óptima y se propone una guía de diseño unificada para controles que sólo miden la tensión de salida Luego, para asegurar robustez en controles muy rápidos, se proponen un modelado y un análisis de estabilidad muy precisos de convertidores DC-DC que tienen en cuenta circuitería para sensado y elementos parásitos críticos. También, usando este modelado, se propone una algoritmo de optimización que tiene en cuenta las tolerancias de los componentes y sensados distorsionados. Us ando este algoritmo, se comparan controles muy rápidos del estado del arte y su capacidad para lograr una rápida respuesta dinámica se posiciona según el condensador de salida utilizado. Además, se propone una técnica para mejorar la respuesta dinámica de los controladores. Todas las propuestas se han corroborado por extensas simulaciones y prototipos experimentales. Con todo, esta tesis sirve como una metodología para ingenieros para diseñar e implementar controles rápidos y robustos de convertidores tipo Buck. ABSTRACT Modern digital electronics present a challenge to designers of power systems. The increasingly high-performance of microprocessors, FPGAs (Field Programmable Gate Array) and ASICs (Application-Specific Integrated Circuit) require power supplies to comply with very demanding static and dynamic requirements. Specifically, these power supplies are low-voltage/high-current DC-DC converters that need to be designed to exhibit low voltage ripple and low voltage deviation under high slew-rate load transients. Additionally, depending on the application, other requirements need to be met such as to provide to the load ”Dynamic Voltage Scaling” (DVS), where the converter needs to change the output voltage as fast as possible without underdamping, or ”Adaptive Voltage Positioning” (AVP) where the output voltage is slightly reduced the greater the output power. Of course, from the point of view of the industry, the figures of merit of these converters are the cost, efficiency and size/weight. Ideally, the industry needs a converter that is cheaper, more efficient, smaller and that can still meet the dynamic requirements of the application. In this context, several approaches to improve the figures of merit of these power supplies are followed in the industry and academia such as improving the topology of the converter, improving the semiconductor technology and improving the control. Indeed, the control is a fundamental part in these applications as a very fast control makes it easier for the topology to comply with the strict dynamic requirements and, consequently, gives the designer a larger margin of freedom to improve the cost, efficiency and/or size of the power supply. In this thesis, how to design and implement very fast controls for the Buck converter is investigated. This thesis proves that sensing the output voltage is all that is needed to achieve an almost time-optimal response and a unified design guideline for controls that only sense the output voltage is proposed. Then, in order to assure robustness in very fast controls, a very accurate modeling and stability analysis of DC-DC converters is proposed that takes into account sensing networks and critical parasitic elements. Also, using this modeling approach, an optimization algorithm that takes into account tolerances of components and distorted measurements is proposed. With the use of the algorithm, very fast analog controls of the state-of-the-art are compared and their capabilities to achieve a fast dynamic response are positioned de pending on the output capacitor. Additionally, a technique to improve the dynamic response of controllers is also proposed. All the proposals are corroborated by extensive simulations and experimental prototypes. Overall, this thesis serves as a methodology for engineers to design and implement fast and robust controls for Buck-type converters.

Anatomía comparada de la madera de Cupressaceae y su correspondencia con los estudios de filogenia

La familia Cupressaceae incluye un total de 133 especies agrupadas en 30 géneros, 17 de los cuales son monospecíficos. Esta familia se encuentra representada en todos los continentes salvo en la Antártida. Sus especies se distribuyen en distintas regiones climáticas, y en altitudes que varían desde el nivel del mar hasta los 5.000 m. La falta de descripción anatómica de muchos de los géneros y especies de Cupressaceae es notable, así como la contradicción que aparece entre distintas investigaciones sobre las características anatómicas de la madera descritas para cada especie. Este estudio describe la anatomía de la madera de Cupressaceae y analiza las características que podrían representar sinapomorfías de los clados delimitados en los estudios filogenéticos. Siguiendo los métodos tradicionales de preparación y descripción de la madera a nivel microscópico, se ha estudiado la madera de 113 especies de los 30 géneros de Cupressaceae. Para ello se han empleado muestras de madera de origen trazable, procedentes de colecciones de madera de distintas instituciones internacionales. Se ha empleado una robusta filogenia molecular para la reconstrucción de los caracteres ancestrales. La anatomía de la madera de los 30 géneros de Cupressaceae, pone de manifiesto la gran homogeneidad de la familia, caracterizada por la presencia de traqueidas axiales sin engrosamientos helicoidales, parénquima radial con paredes horizontales lisas, punteaduras del campo de cruce de tipo cupresoide y la carencia de canales resiníferos fisiológicos. Además, todos presentan parénquima axial (salvo Neocallitropsis, Thuja y Xanthocyparis), punteaduras radiales areoladas con toro definido (salvo Thuja y Thujopsis), siendo habitual la presencia de punteaduras areoladas en las paredes tangenciales de la madera tardía, y verrugosidades en la cara interna de las traqueidas (salvo Ca. macleayana, Libocedrus, Papuacedrus y Neocallitropsis). Los radios leñosos son homogéneos y están compuestos de parénquima radial (con la presencia de traqueidas radiales en algunas especies de Cupressus, Sequoia, Thujopsis y X. nootkatensis) con paredes finales lisas o lisas y noduladas (exclusivamente noduladas en Cal. macrolepis, C. bakeri y en la mayoría de especies de Juniperus), y el rango de altura de los radios leñosos se encuentra entre 5 y 15 células. Se consideran posibles sinapomorfismos de Cupressaceae la presencia de verrugosidades en la cara interna de las traqueidas, la presencia de traqueidas axiales sin engrosamientos helicoidales, la presencia de parénquima axial, la presencia de radios leñosos homogéneos (compuestos únicamente de parénquima radial), la tipología de las paredes horizontales del parénquima radial, las punteaduras del campo de cruce de tipo cupresoide y la ausencia de canales resiníferos fisiológicos, pero lo que realmente diferencia a este grupo de coníferas es la simultaneidad de todos estos caracteres en sus maderas. Como sinapomorfías específicas por clados se proponen: la ausencia de toro definido y muescas en el borde de las punteaduras en Thuja-Thujopsis, la existencia de extensiones de toro en Diselma-Fitzroya-Widdringtonia; la presencia de engrosamientos callitroides en Callitris-Actinostrobus; la presencia de espacios intercelulares y las muescas en el borde de las punteaduras en el clado formado por el género Juniperus y las especies de Cupressus en la región oriental; la presencia de paredes finales del parénquima radial tanto lisas como noduladas en los clados formados por el género Xanthocyparis y las especies de Cupressus en la región occidental y en Fitzroya-Diselma; y por último, la presencia de punteaduras del campo de cruce de tipo taxodioide en los clados taxodioid y sequoioid. ABSTRACT The Cupressaceae family comprises 133 species grouped into 30 genera, 17 of which are monotypic. The family is represented in all continents except Antarctica. Its species are distributed in various climate zones and at altitudes from sea level to 5,000 m. There is a considerable lack of anatomical descriptions for many genera and species of Cupressaceae and much contradiction between studies about the wood anatomical features described for each species. This study describes the wood anatomy of Cupressaceae and analyses the features that could represent synapomorphies of the clades recovered in phylogenetic studies. Following the traditional methods of preparation and description of wood at microscopic level, a study was made of the wood of 113 species of the 30 Cupressaceae genera. The study samples had traceable origins and came from wood collections held at various international institutions. A robust molecular phylogeny was used for ancestral state reconstruction. The wood anatomy of the 30 genera of the Cupressaceae shows the high homogeneity of the family, which is characterised by the presence of axial tracheids without helical thickenings, smooth horizontal walls of ray parenchyma cells, cupressoid cross-field pits, and the absence of physiological resin canals. In addition, they all have axial parenchyma (except Neocallitropsis, Thuja and Xanthocyparis), a warty layer on the inner wall of the tracheids (except Ca. macleayana, Libocedrus, Papuacedrus and Neocallitropsis) and tracheid pitting in radial walls with a well defined torus (except Thuja and Thujopsis); tracheid pitting in the tangential walls of the latewood is common. Rays are homogeneous and are composed of ray parenchyma (with the presence of ray tracheids in some species of Cupressus, Sequoia, Thujopsis and X. nootkatensis), with smooth end walls or both smooth and nodular end walls (exclusively nodular in Cal. macrolepis, C. bakeri and most Juniperus species), and ray height range is 5 to 15 cells. Possible synapomorphies of Cupressaceae are the presence of a warty layer on the inner layer of the tracheids, axial tracheids without helical thickenings, the presence of axial parenchyma, homogeneous rays (composed exclusively of ray parenchyma), the typology of the horizontal walls of ray parenchyma cells, cupressoid cross-field pits and the absence of physiological resin canals, but what truly differentiates this group of softwoods is the co-occurrence of all these features in their wood. The following are proposed as clade-specific synapomorphies: absence of a well-defined torus and presence of pits with notched borders in Thuja-Thujopsis, torus extensions in Diselma-Fitzroya-Widdringtonia; callitroid thickenings in Callitris-Actinostrobus; intercellular spaces and pits with notched borders in the clade formed by the genus Juniperus and the species of Cupressus in the eastern region; smooth and nodular ray parenchyma end walls in the clades formed by the genus Xanthocyparis and the species of Cupressus in the western region and in Fitzroya-Diselma, and taxodioid cross-field pits in the taxodioid and sequoioid clades.