Undercooling and Rapid Solidification of Nb-Si Eutectic Alloys Studied by Long Drop Tube

Niobium-silicide alloys have great potential for high temperature turbine applications. The two-phase Nb/Nb5Si3 in situ composites exhibit a good balance in mechanical properties. Using the 52 in drop tube, the effect of undercooling and rapid solidification on the solidification process and micro-structural characterization of Nb-Si eutectic alloy was studied. The microstructures of the Nb-Si composites were investigated by optics microscope (OM), X-ray diffraction (XRD) and scanning electron microscope (SEM) equipped with X-ray energy dispersive spectrometry (EDS). Up to 480 K, deep undercooling of the Nb-Si eutectic samples was successfully obtained, which corresponds to 25% of the liquidus temperature. Contrasting to the conventional microstructure usually found in the Nb-Si eutectic alloy, the microstructure of the undercooled sample is divided into the fine and coarse regions. The most commonly observed microstructure is Nb+Nb5Si3, and the Nb3Si phase is not be found. The change of coarseness of microstructure is due to different cooling rates during and after recalescence. The large undercooling is sufficient to completely bypass the high temperature phase field.

Lei de acesso à informação (LAI) : investigação da transparência nos três Poderes

A Lei 12.527/2011, Lei de Acesso à Informação (LAI), representa um avanço na disponibilização da informação pública pelos órgãos governamentais, de maneira a promover a transparência das ações e a consolidação da cidadania. Este artigo tem como foco a observância do atendimento dos preceitos de transparência ativa pelos sítios oficiais de órgãos públicos federais dos Poderes Executivo, Legislativo e Judiciário.

Investigation of Vaporized Kerosene Injection in a Supersonic Model Combustor

Characteristics of vaporized aviation kerosene injection in a supersonic model combustor were preliminarily investigated. The electrically storage type heater has a volume capacity of heating kerosene of 0.8 kg up to 670 K at a pressure of 5.5 Mpa. The temperature to cause pressurized kerosene jet being fully vaporized in Quiescent atmosphere was found to be 550 K at 4 Mpa however the pressurized hot kerosene remains in liquid state within the tube. The correspondent jet spray in Mach 2.5 vitiated air cross-flow were visualized by using stop schlieren photograph.It was found the penetration depth of the hot pressurized kerosene jet is approximately same with the temperature varied from 290 K to 550 k. at pressure of 4 Mpa. This results showed that the atomization process of hot kerosene jet spray in supersonic combustor could be bypassed and directly transferred to be gas state at temperature 550 K and pressure of 4 Mpa.

Long-Term Growth and Persistence with Endogenous Depreciation: Theory and Evidence

Previous research has shown a strong positive correlation between short-term persistence and long-term output growth as well as between depreciation rates and long-term output growth. This evidence, therefore, contradicts the standard predictions from traditional neoclassical or AK-type growth models with exogenous depreciation. In this paper, we first confirm these findings for a larger sample of 101 countries. We then study the dynamics of growth and persistence in a model where both the depreciation rate and growth are endogenous and procyclical. We find that the model s predictions become consistent with the empirical evidence on persistence, long-term growth and depreciation rates.

Performance of a Supersonic Model Combustor using Vaporized Kerosene Injection

Characteristics of supersonic combustion by injecting kerosene vapor into a Mach 2.5 crossflow at various preheat temperatures and pressures were investigated experimentally. A two-stage heating system has been designed and tested, which can prepare heated kerosene of 0.8 kg up to 820 K at pressure of 5.5 Mpa with minimum/negligible fuel coking. In order to simulate the thermophysical properties of kerosene over a wide range of thermodynamic conditions, a three-component surrogate that matches the compound class of the parent fuel was employed. The flow rate of kerosene vapor was calibrated using a sonic nozzle. Computed flow rates using the surrogate fuel are in agreement with the experimental data. Kerosene jets at various preheat temperatures injecting into both quiescent environment and Mach 2.5 crossflow were visualized. It was found that at injection pressure of 4 Mpa and preheat temperature of 550 K the kerosene jet was completely in vapor phase, while keeping almost the same penetration depth as compared to the liquid kerosene injection. Supersonic combustion tests were also carried out to compare the combustor performance for the cases of vaporized kerosene injection, liquid kerosene injection, and effervescent atomization with hydrogen barbotage, under the similar stagnation conditions. Experimental results demonstrated that the use of vaporized kerosene injection leads to better combustor performance. Further parametric study on vaporized kerosene injection in a supersonic model combustor is needed to assess the combustion efficiency as well as to identify the controlling mechanism for the overall combustion enhancement.

Investigation of Vaporized Kerosene Injection and Combustion in a Supersonic Model Combustor

Injection and combustion of vaporized kerosene was experimentally investigated in a Mach 2.5 model combustor at various fuel temperatures and injection pressures. A unique kerosene heating and delivery system, which can prepare heated kerosene up to 820 K at a pressure of 5.5 MPa with negligible fuel coking, was developed. A three-species surrogate was employed to simulate the thermophysical properties of kerosene. The calculated thermophysical properties of surrogate provided insight into the fuel flow control in experiments. Kerosene jet structures at various preheat temperatures injecting into both quiescent environment and a Mach 2.5 crossflow were characterized. It was shown that the use ofvaporized kerosene injection holds the potential of enhancing fuel-air mixing and promoting overall burning. Supersonic combustion tests further confirmed the preceding conjecture by comparing the combustor performances of supercritical kerosene with those of liquid kerosene and effervescent atomization with hydrogen barbotage. Under the similar flow conditions and overall kerosene equivalence ratios, experimental results illustrated that the combustion efficiency of supercritical kerosene increased approximately 10-15% over that of liquid kerosene, which was comparable to that of effervescent atomization.

Characteristics of Wake Flow in Long Bluff Bodies

Vortex shedding is the main characteristics of bluff bodies, which will cause the bluff bodies to vibrate and sometimes result in the structures failure. In this paper the wake flow characteristics of 21 bluff bodies with rectangular, rounded and angular profiles and the length-to-width ratio in the range of 4~12 were deeply studied by Micro ADV. Two parameters, namely the relative intensity of the load due to Karman vortices and the large scale vortex intensity, were introduced to measure the wake flow intensity. Generally, the values of these parameters for different bluff bodies are consistent with each other. The experiment results showed that the key factor affecting the wake flow characteristics is the bluff edge, especially the leading edge geometry. The wake flow in bluff bodies with rounded edge profiles has more regular vortices and becomes more periodic than that in bluff bodies with rectangular ones. A bluff body with angular edged profile was witnessed to have not only small wake loading but small hydraulic resistance also.

What Do We Know about Long Laminar Plasma Jets?

Silent and stable long laminar plasma jets can be generated in a rather wide range of working parameters. The laminar flow state can be maintained even if considerable parameter fluctuations exist in the laminar plasma jet or if there is an impact of laterally injected particulate matter and its carrier gas. The attractive special features of laminar plasma jets include extremely low noise level, less entrainment of ambient air, much longer and adjustable high-temperature region length, and smaller axial gradient of plasma parameters. Modeling results show that the laminar plasma jet length increases with increasing jet inlet velocity or temperature and the effect of natural convection on laminar plasma jet characteristics can be ignored, consistent with experimental observations. The large difference between laminar and turbulent plasma jet characteristics is revealed to be due to their different laws of surrounding gas entrainment. Besides the promising applications of the laminar plasma jet to remelting and cladding strengthening of the metallic surface and to thermal barrier coating preparation, it is expected that the laminar plasma jet can become a rather ideal object for the basic studies of thermal plasma science owing to the nonexistence of the complexity caused by turbulence.

Size composition of catches of Yellowfin tuna in the Japanese long-line fishery in the eastern tropical Pacific east of 130°W

ENGLISH (pgs. 267-283): In the spring of 1963, the senior author, who is a member of the staff of the Nankai Regional Fisheries Research. Laboratory, Fisheries Agency, Japanese Government, came to the Institute of Marine Resources of the University of California as a visiting investigator, bringing with him catch statistical data from the fishery in the eastern Pacific, which had been collected at the Nankai Regional Fisheries Research Laboratory (NRFRL) through September 1962, in order to conduct studies of these data in collaboration with the junior author, and with investigators of the InterAmerican Tropical Tuna Commission. A general review of the long-line fishery, based on the catch statistics of the commercial fishing fleet has been published by Suda and Schaefer (1965). In this paper we present an analysis of data respecting the size-composition of yellowfin tuna taken on long-line gear throughout the eastern Pacific between 1958 and 1962, and make some comparisons with data on size-composition of yellowfin tuna taken in the near-surface fishery, by bait boats and purse-seiners, in waters adjacent to the American coast. As has been shown by Suda and Schaefer (1965), the long-line fishery in the eastern Pacific is primarily directed toward the capture of bigeye tuna. However, considerable quantities of yellowfin tuna are also taken on this gear, and, in addition, there are substantial catches of albacore and of several species of spearfishes in some parts of the range of this fishery. Information respecting the catch rates of yellowfin tuna, and information respecting the size-composition of the stock of yellowfin tuna being exploited by the long-line fishery, is of particular interes~" because the yellowfin tuna population of the eastern Pacific is also subject to an intensive fishery by baitboats and purse-seiners which capture this species, together with skipjack, near the surface along the coast of the Americas, and around the outlying islands, in the region of California to northern Chile. SPANISH (pgs. 311-329): En la primavera de 1963, el autor principal, quien es miembro del personal del Nankai Regional Fisheries Research Laboratory, Fisheries Agency del gobierno japonés, vino al Institute of Marine Resources de la Universidad de California en calidad de investigador visitante y trajo consigo datos estadísticos de las capturas de la pesquería en el Pacífico oriental, que habían sido recolectados en el Nankai Regional Fisheries Research Laboratory (NRFRL) hasta septiembre de 1962, con el fin de hacer estudios de esos datos en colaboración con el coautor y con investigadores de la Comisión Interamericana del Atún Tropical. Una revisión general de la pesquería con palangre, basada sobre las estadísticas de captura de la flota pesquera comercial, ha sido publicada por Suda y Schaefer (1965). En este trabajo presentamos un análisis de los datos correspondientes a la composición de tamaños del atún aleta amarilla capturado con equipo palangrero en todo el Pacífico oriental, entre 1958 y 1962, y hacemos algunas comparaciones con los datos sobre la composición de tamaños del atún aleta amarilla cogido en la pesquería superficial cercana, por barcos de carnada y rederos en aguas adyacentes a la costa americana. Como ha sido demostrado por Suda y Schaefer (1965) la pesquería con palangre en el Pacífico oriental tiene como principal objeto la captura del atún ojo grande. Sin embargo, considerables cantidades de atún aleta amarilla son capturadas también por este equipo y, además, hay también considerables capturas de albacora y de diversas especies de peces-espada en algunas partes de la región que abarca esta pesquería. La información respecto a las tasas de captura del atún aleta amarilla, y la relativa a la composición de tamaños del stock de esta especie que explota la pesquería con palangre, es de particular interés, a causa de que la población de atún aleta amarilla del Pacífico oriental es también objeto de una pesca intensiva por barcos de carnada y rederos que capturan esta especie, junto con el barrilete, cerca de la superficie a 10 largo de la costa de las Américas y alrededor de las islas mar afuera, en la región desde California hasta el norte de Chile.

A Comparison of Two Methods for Enhancing the Recovery of Seagrasses into Propellor Scars: Mechanical Injection of a Nutrient and Growth Hormone Solution vs. Defecation by Roosting Seabirds: Final Report.

Based on the recovery rates for Thalassia testudinum measured in this study for scars of these excavation depths and assuming a linear recovery horizon, we estimate that it would take ~ 6.9 years (95% CI. = 5.4 to 9.6 years) for T. testudinum to return to the same density as recorded for the adjacent undisturbed population. The application of water soluble fertilizers and plant growth hormones by mechanical injection into the sediments adjacent to ten propellor scars at Lignumvitae State Botanical Site did not significantly increase the recovery rate of Thalassia testudinum or Halodule wrightii. An alternative method of fertilization and restoration of propellor scars was also tested by a using a method of “compressed succession” where Halodule wrightii is substituted for T. testudinum in the initial stages of restoration. Bird roosting stakes were placed among H.wrightii bare root plantings in prop scars to facilitate the defecation of nitrogen and phosphorus enriched feces. In contrast to the fertilizer injection method, the bird stakes produced extremely high recovery rates of transplanted H. wrightii. We conclude that use of a fertilizer/hormone injection machine in the manner described here is not a feasible means of enhancing T. testudinum recovery in propellor scars on soft bottom carbonate sediments. Existing techniques such as the bird stake approach provide a reliable, and inexpensive alternative method that should be considered for application to restoration of seagrasses in these environments. Document contains 40 pages)

Long-Term Monitoring of Ecological Conditions In Gray’s Reef National Marine Sanctuary: Comparison of soft-bottom benthic assemblages and contaminant levels in sediments and biota in Spring 2000 and 2005

As part of an ongoing program of benthic sampling and related assessments of sediment quality at Gray’s Reef National Marine Sanctuary (GRNMS) off the coast of Georgia, a survey of soft-bottom benthic habitats was conducted in spring 2005 to characterize condition of macroinfaunal assemblages and levels of chemical contaminants in sediments and biota relative to a baseline survey carried out in spring 2000. Distribution and abundance of macrobenthos were related foremost to sediment type (median particle size, % gravel), which in turn varied according to bottom-habitat mesoscale features (e.g., association with live bottom versus flat or rippled sand areas). Overall abundance and diversity of soft-bottom benthic communities were similar between the two years, though dominance patterns and relative abundances of component species were less repeatable. Seasonal summer pulses of a few taxa (e.g., the bivalve Ervilia sp. A) observed in 2000 were not observed in 2005. Concentrations of chemical contaminants in sediments and biota, though detectable in both years, were consistently at low, background levels and no exceedances of sediment probable bioeffect levels or FDA action levels for edible fish or shellfish were observed. Near-bottom dissolved oxygen levels and organic-matter content of sediments also have remained within normal ranges. Highly diverse benthic assemblages were found in both years, supporting the premise that GRNMS serves as an important reservoir of marine biodiversity. A total of 353 taxa (219 identified to species) were collected during the spring 2005 survey. Cumulatively, 588 taxa (371 identified to species) have been recorded in the sanctuary from surveys in 2000, 2001, 2002, and 2005. Species Accumulation Curves indicate that the theoretical maximum should be in excess of 600 species. Results of this study will be of value in advancing strategic science and management goals for GRNMS, including characterization and long-term monitoring of sanctuary resources and processes, as well as supporting evolving interests in ecosystem-based management of the surrounding South Atlantic Bight (SAB) ecosystem. (PDF contains 46 pages)