Effects of Strand Geometry on Selected Properties of Long-Stand Structural Composite Lumber Made from Northeastern Hardwoods

Structural composite lumber (SCL) products often possess significantly higher design values than the top grades of solid lumber, making it a popular choice for both residential and commercial applications. The enhanced mechanical properties of SCL are mainly due to defect randomization and densification of the wood fiber, both largely functions of the size, shape and composition (species) of the wood element. Traditionally, SCL manufacturers have used thin, rectangular elements produced from either moderate density softwoods or low density hardwoods. Higher density hardwood species have been avoided, as they require higher pressures to adequately densify and consolidate the wood furnish. These higher pressures can lead to increased manufacturing costs, damage to the wood fiber and/or a product that is too dense, making it heavy and unreceptive to common mechanical fastening techniques. In the northeastern United States high density, diffuse-porous hardwoods (such as maple, beech and birch) are abundant. Use of these species as primary furnish for a SCL product may allow for a competitive advantage in terms of resource cost against products that rely on veneer grade logs. Proximity to this abundant and relatively inexpensive resource may facilitate entry of SCL production facilities in the northeastern United States, where currently none exist. However, modifications to current strand sizes, geometries or production techniques will likely be required to allow for use of these species. A new SCL product concept has been invented allowing for use of these high density hardwoods. The product, referred to as long-strand structural composite lumber (LSSCL), uses strands of significantly larger cross sectional areas and volumes than existing SCL products. In spite of the large strand size, satisfactory consolidation is achieved without excessive densification of the wood fiber through use of a symmetrical strand geometric cross-section. LSSCL density is similar to that of existing SCL products, but is due mainly to the inherent density of the species, rather than through densification. An experiment was designed and conducted producing LSSCL from both large (7/16”) and small (1/4”) strands, of both square and triangular geometric cross sections. Testing results indicate that the large, triangular strands produce LSSCL beams with projected design values of: Modulus of elasticity (MOEapp) – 1,750,000 psi; Allowable bending stress (Fb) – 2750 psi; Allowable shear stress (Fv) – 260 psi. Several modifications are recommended which may lead to improvement of these values, likely allowing for competition against existing SCL products.

Alterations in the Cellular Composition of the Mouse Bladder Following Ovariectomy, Partial Bladder Outlet Obstruction, and Aging

Detrusor underactivity (DU) increases susceptibility to urinary retention and accordingly further complicates the management of urinary incontinence. Bladder muscle stretch, a lack of estrogen, and aging are 3 notable DU risk factors. The aim of this research is to better characterize the changes in cellular composition of the bladder that result from these 3 risk factors to gain a better understanding of DU pathogenesis and pathobiology. This research focuses on the effects of a lack of estrogen while also providing an outline for determining the effects of bladder muscle stretch and aging on the cellular composition of the bladder.

Partial pressure of carbon dioxide along the Transatlantic section from 7 November till 19 December 2000

Along a transatlantic section from 57°N to 60°S that was carried out from November 7 till December 19, 2000 on board R/V Horizont II concentrations of CO2 were measured in the near-water layer of the air and differences between partial pressures in water and air in various climatic zones were calculated. It was shown that variations of CO2 concentrations in the near-water layer of air and those of values of water-air partial pressure difference were from 324x10**-6 to 426x10**-6 and from 150x10**-6 to 100x10**-6 atm, respectively. Maximum value of CO2 partial pressure in air in the near-water layer (426x10**-6 atm) was noted at 45°-47°N; minimum of 324x10**-6 atm was found in Antarctica at 59°S. During measurenents maximum value of CO2 partial pressure difference in water and air (150 x10**-6) was observed at 45°-48°N; maximum flux in this case was directed from the atmosphere to water. Maximum value of CO2 partial pressure difference in water and air for flux directed from the ocean to air (100 x10**-6) was observed at 59°-60°S. Comparison of calculated values of partial pressure difference in water and air with previous data points to more intense exchange of CO2 between the ocean and atmosphere during the survey period was considered. According to values of CO2 partial pressure difference in air and water as compared to 1975, exchange intensity in the Northern Hemisphere (absorption from the atmosphere) increased. A well-pronounced latitudinal effect of distribution of CO2 partial pressure in air was observed. Along the route variations in CO2 concentrations in zones of water divergence and convergence were registered.

Partial melting experiments on oceanic cumulated gabbros

We performed hydrous partial melting experiments at shallow pressures (0.2 GPa) under slightly oxidizing conditions (NNO oxygen buffer) on oceanic cumulate gabbros drilled by ODP (Ocean Drilling Program) cruises to evaluate whether the partial melting of oceanic gabbro can generate SiO2-rich melts with compositions typical of oceanic plagiogranites. The experimental melts of the low-temperature runs broadly overlap those of natural plagiogranites. At 940 °C, the normalized SiO2 contents of the experimental melts of all systems range between 60 and 61 wt%, and at 900 °C between 63 and 68 wt%. These liquids are characterized by low TiO2 and FeOtot contents, similar to those of natural plagiogranites from the plutonic section of the oceanic crust, but in contrast to Fe and Ti-rich low-temperature experimental melts obtained in MORB systems at ~950 °C. The ~1,500-m-long drilled gabbroic section of ODP Hole 735B (Legs 118 and 176) at the Southwest Indian Ridge contains numerous small plagiogranitic veins often associated with zones which are characterized by high-temperature shearing. The compositions of the experimental melts obtained at low temperatures match those of the natural plagiogranitic veins, while the compositions of the crystals of low-temperature runs correspond to those of minerals from high-temperature microscopic veins occurring in the gabbroic section of the Hole 735B. This suggests that the observed plagiogranitic veins are products of a partial melting process triggered by a water-rich fluid phase. If the temperature estimations for hightemperature shear zones are correct (up to 1,000 °C), and a water-rich fluid phase is present, the formation of plagiogranites by partial melting of gabbros is probably a widespread phenomenon in the genesis of the ocean crust.