Measures of turbidity in coastal waters, Coconut Island, Oahu, Hawaii, August 31 - September 2, 2005: workshop proceedings

A three day workshop on turbidity measurements was held at the Hawaii Institute of Marine Biology from August 3 1 to September 2, 2005. The workshop was attended by 30 participants from industry, coastal management agencies, and academic institutions. All groups recognized common issues regarding the definition of turbidity, limitations of consistent calibration, and the large variety of instrumentation that nominally measure "turbidity." The major recommendations, in order of importance for the coastal monitoring community are listed below: 1. The community of users in coastal ecosystems should tighten instrument design configurations to minimize inter-instrument variability, choosing a set of specifications that are best suited for coastal waters. The IS0 7027 design standard is not tight enough. Advice on these design criteria should be solicited through the ASTM as well as Federal and State regulatory agencies representing the majority of turbidity sensor end users. Parties interested in making turbidity measurements in coastal waters should develop design specifications for these water types rather than relying on design standards made for the analysis of drinking water. 2. The coastal observing groups should assemble a community database relating output of specific sensors to different environmental parameters, so that the entire community of users can benefit from shared information. This would include an unbiased, parallel study of different turbidity sensors, employing a variety of designs and configuration in the broadest range of coastal environments. 3. Turbidity should be used as a measure of relative change in water quality rather than an absolute measure of water quality. Thus, this is a recommendation for managers to develop their own local calibrations. See next recommendation. 4. If the end user specifically wants to use a turbidity sensor to measure a specific water quality parameter such as suspended particle concentration, then direct measurement of that water quality parameter is necessary to correlate with 'turbidity1 for a particular environment. These correlations, however, will be specific to the environment in which they are measured. This works because there are many environments in which water composition is relatively stable but varies in magnitude or concentration. (pdf contains 22 pages)

Ground water-surface water interactions sensor technology, Savannah, Georgia, March 7-9, 2005: workshop proceedings

The Alliance for Coastal Technologies (ACT) held a Workshop on Sensor Technology for Assessing Groundwater-Surface Water Interactions in the Coastal Zone on March 7 to 9,2005 in Savannah, GA. The main goal of the workshop was to summarize the general parameters, which have been found to be useful in assessing groundwater-surface water (GW-SW) interactions in the coastal zone. The workshop participants (Appendix I) were specifically charged with identifying the types of sensor systems, if any, that have been used to obtain time-series data and to make known which parameters may be the most amenable to the development/application of sensor technology. The group consisted of researchers, industry representatives, and environmental managers. Four general recommendations were made: 1. Educate coastal managers and agencies on the importance of GW-SW interactions, keeping in mind that regulatory agencies are driven by a different set of rules than researchers: the focus is on understanding the significance of the problem and providing solutions. ACT could facilitate this process in two ways. First, given that the research literature on this subject is fairly diffuse, ACT could provide links from its web site to fact sheets or other literature. Second, ACT could organize a focused meeting for managers and/or agency groups. Encourage development of primary tools for quantifying flow. The most promising technology in this respect is flow meters designed for flux chambers, mainly because they should be simple to use and can be made relatively inexpensively. However, it should be kept in mind that they provide only point measurements and several would need to be deployed as a network in order to obtain reliable flow estimates. For evaluating system wide GW-SW interactions, tools that integrate the signal over large areas would be required. Suggestions include a user-friendly hydrogeologic models, keeping in mind that freshwater flow is not the entire story, or continuous radon monitors. Though the latter would be slightly more difficult to use in terms of background knowledge, such an instrument would be low power and easy to operate and maintain. ACT could facilitate this recommendation by identifying funding opportunities on its web site and/or performing evaluations of existing technologies that could be summarized on the web site. (pdf contains 18 pages)

Applications of in situ Fluorometers in Nearshore waters, Cape Elizabeth, Maine, February 2-4,2005: workshop proceedings

The Alliance for Coastal Technologies (ACT) Workshop "Applications of in situ Fluorometers in Nearshore Waters" was held in Cape Elizabeth, Maine, February 2-4,2005, with sponsorship by the Gulf of Maine Ocean Observing System (GoMOOS), one of the ACT partner organization. The purpose of the workshop was to explore recent trends in fluorometry as it relates to resource management applications in nearshore environments. Participants included representatives from state and federal environmental management agencies as well as research institutions, many of whom are currently using this technology in their research and management applications. Manufacturers and developers of fluorometric measuring systems also attended the meeting. The Workshop attendees discussed the historical and present uses of fluorometry technology and identified the great potential for its use by coastal managers to fulfill their regulatory and management objectives. Participants also identified some of the challenges associated with the correct use of Fluorometers to estimate biomass and the rate of primary productivity. The Workshop concluded that in order to expand the existing use of fluorometers in both academic and resource management disciplines, several issues concerning data collection, instrument calibration, and data interpretation needed to be addressed. Participants identified twelve recommendations, the top five of which are listed below: Recommendations 1) Develop a "Guide" that describes the most important aspects of fluorescence measurements. This guide should be written by an expert party, with both research and industry input, and should be distributed by all manufacturers with their instrumentation. The guide should also be made available on the ACT website as well as those of other relevant organizations. The guide should include discussions on the following topics: The benefits of using fluorometers in research and resource management applications; What fluorometers can and cannot provide in terms of measurements; The necessary assumptions required before applying fluorometry; Characterization and calibration of fluorometers; (pdf contains 32 pages)

Texture measurement on gutted cod during storage in ice using a hand-held instrument

Fish muscle as food is to be seen as highly perishable. In unfrozen fish, freshness is considered the most important quality attribute. It is well known that there are several biochemical changes that can affect dramatically the texture of fish muscle. Immediately after death the fish texture is soft and elastic. In connection with rigor mortis the fish texture changes markedly. It becomes harder during rigor and after its resolution it becomes softer. This softness increases due to proteolysis during further storage at refrigerated conditions. Texture is a very important indicator for evaluating the quality of fish. Barroso et al. (1997) have recently reviewed mechanical methods in use for texture measurements on fresh fish. Further reviews on texture measurement performed on fish muscle were recently published underlining the importance of texture as quality attribute (Hyldig et al 2001, Coppes et al. 2002). The position along the fish can influence the results and was investigated by several authors (Sigurgis-ladottir et. al. 1999). Different methods have been compared for their ability to differentiate between recently killed salmon and salmon stored on ice for up to 24 days (Veland et al. 1999).

Developing a viable fish farming industry in Nigeria -- an alternative strategy to the strategy in the Green Revolution Programme

A study was embarked upon with the twin objectives of reviewing the Green Revolution Strategy for accelerating fish production in the country and proposing an alternative strategy, a private sector approach. Some of the programmes listed in the Green Revolution are very necessary for developing a viable - fish farming industry and that money spent under such programmes is money well spent. Programmes that are also desirable but need to be considerably expanded were identified. Other programmes have been criticised on the grounds that the method chosen to achieve the desired objectives is fraught with dangers if sufficiently long run view of fisheries development is taken

A review of manpower training for Nigeria's fishing industry

An examination is made of the organization and administration of fisheries training institutes in Nigeria, highlighting their inadequacies in achieving required goals. A systems approach to fisheries manpower training is described which is based on 4 principles: 1) wholeness; 2) systematization; 3) compatibility; and 4) optimization

Relevance of the programmes of the federal fisheries schools to Nigeria's fishing industry

Nigeria's three federal fisheries schools are administered by three autonomous research institutes located in Lagos, New Bussa, and Maiduguri. The schools were established at different periods to train the required manpower for Nigeria's fishing industry which has remained predominantly artisanal since its inception in 1942 as a Second World War exigency. Despite the establishment of the schools, the industry's manpower is still being dominated by non-nationals especially in the capture fisheries sub-sector. The common features of the schools include the apparent insensitivity of their programmes to the industry's dynamic manpower needs; the absence of coordination of their programmes by a national body which would have ensured that the schools are able to communicate with one another and are willing to act and share a purpose. The need and the methodology for a change of emphasis from the on-going training of extension agents and officers to that of fishing operatives and technicians to enable Nigeria effectively harness her local fish resources towards self-sufficiency is highlighted.

Trace metals -- a potential threat to our fishing industry

Trace metals constitute a major form of water pollutant that can adversely affect fish production. The potentially toxic metals have been identified as lead, zinc, copper, arsenic, antimony, mercury beryllium, barium, cadmium, chromium, nickel, selenium among others. Preliminary laboratory studies have been directed to the determination of traces of lead in the aquatic biota and its toxicity. There are indications that the levels reported in effluents from some of the industries may be above the tolerant limits of local fish species and organisms that make up their food. Metal pollution could become a serious problem to freshwater fisheries in the future as a result of increasing urbanization and industrialization, unless efforts are made to prevent it

Artisanal canoe fishing industry of the Rivers State: its economic viability and investment potentials

Consequent upon the present national call in Nigeria for all to go back to agriculture including fishing, most retrenched workers and unemployed youths from the riverine areas are taking up fishing as a legitimate and gainful livelihood. To sustain this tempo and attract more investment, the economic viability of such projects must be known. This study is an attempt to document the profitability and investment potential of artisanal canoe fishing. Socio-economic information including catches, operational cost and returns were obtained through a personal interview questionnaire survey of 240 randomly selected artisanal canoe fishermen from Bonny, Brass and Degema Local Government Areas (LGA) of the State and analyzed. With an investment cost of about 8,135, 8,490 and 6,571 and operation cost of 750, 776 and 627, the analysis showed an average monthly gross income of 1,869, 3,221 and 1,775 for the three local government areas respectively. A benefit-cost-ratio of 1:8, net present value of 400, 603 and internal rate of return greater than 50% were obtained. Since capital invested in fisheries is not tied up for long before benefits start flowing, coupled with the high IRR, it is concluded that artisanal canoe fishing would be an economically viable venture if well managed

An economic overview of the fish and shrimp production of the Nigeria fish trawling industry under the structural adjustment programme

Over the years, Nigeria have witnessed different government with different policy measures. Against the negative consequences of the past policies, the structural adjustment was initiated in 1986. Its aims is to effectively altar and restructure the consumption patterns of the economy as well as to eliminate price distortions and heavy dependence on the oil and the imports of consumer goods and services. Within the period of implementation, there has been a decreasing trend in yearly fish catch landings and sizes but the reverse in shrimping. There is also a gradual shift from fishing to shrimping, from the vessels purchased with 83.3% increase of shrimpers from 1985 to 1989. Decreasing fish catch sizes and quantity aggravated by the present high cost of fishing coupled with the favourable export market for Nigeria shrimp tend to influence the sift. This economic situation is the result of the supply measures of SAP through the devaluation of the Naira. There is also overconcentration of vessels on the inshore waters as majority of the vessels are old and low powers hence incapable of fishing on the deep sea. Rotterdam price being paid for automotive gas oil (AGO) by fishing industries is observed to be discriminating and unhealthy to the growth of the industry as it is exceedingly high and unstable thus affecting planning for fishing operation. Fuel alone takes 43% of the total cost of operation. The overall consequences is that fishing days are loss and therefore higher overhead cost. It was concluded that for a healthy growth and sustainable resources of our marine fishery under the structural adjustment programme licensing of new fishing vessels should be stopped immediately and the demand side of SAP should be employed by subsidizing high powered fishing vessels which can operate effectively on the deep sea

Aspects of the fishing industry and an overview of artificial reefs and fish aggregating devices for increasing fisheries output and viability in Nigeria

Aspects of the Nigerian fishing industry are outlined to explain the concept of fishing systems viability which is often influenced by a combination of factors including biological productivity, as well as technical, economic and social factors. The productivity of the aquatic environments can be increased by the construction and installation of artificial reefs and fish aggregating devices. These man-made structures provide shelters, food and breeding grounds for fin fish and shell fish. The habitat enhancement techniques are appropriate, efficient, cheap and simple strategic options for increase in fish production. Recommendations for effective utilization and long term management are outlined.

A new method and instrument for accurately measuring interval between ultrashort pulses

Using second-order autocorrelation conception, a novel method and instrument for accurately measuring interval between two linearly polarized ultrashort pulses with real time were presented. The experiment demonstrated that the measuring method and instrument were simple and accurate (the measurement error <5 fs). During measuring, there was no moving element resulting in dynamic measurement error.