Effect of heat input on the mechanical properties of welded joints in high strength steels

Experiments were carried out to determine the properties of the welded joints in 8mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm21 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.

Paineventtiilien hitsauksen laadunhallinnan kehittäminen

Diplomityössä tarkastellaan keinoja Temet Oy:n valmistamien paineventtiilien hitsauksen laadunhallinnan kehittämiseen. Työn avulla hitsauksen laadunhallinta on tarkoitus saada vastaamaan paremmin yrityksen asiakkaiden vaatimuksia sekä samalla parantaa yrityksen kilpailukykyä. Työn alkupuolella perehdytään laatuun ja laadunhallintaan, erityisesti hitsauksen näkökulmasta. Lisäksi tutustutaan laadunhallinnan työkaluihin, ISO 9001- ja ISO 3834 -standardeihin sekä tarkemmin jälkimmäisen vaatimuksiin. Lisäksi työhön sisältyy kahden erityyppisen paineventtiilin hitseille tehtävä makrohietutkimus. Työssä haetaan myös paineventtiilien valmistukselle vaatimuksia antavia viranomaismääräyksiä tai standardeja. Oleellinen osa hitsauksen laadunhallinnan kehitystyötä on yrityksen hitsaustoiminnan nykytilanteen kartoittaminen ja tarvittavien kehitystoimien suunnittelu tehtyihin selvityksiin perustuen. Työn valmistuttua yrityksellä on ehdotus siitä, miten toteuttaa ISO 3834-2 kattavien laatuvaatimusten mukaisen hitsauksen laadunhallintajärjestelmä paineventtiilien hitsaukseen. Yrityksellä on myös laadunhallintajärjestelmän kannalta oleelliset asiakirjat ja ehdotus siitä, miten hitsauksen laadunhallinnan kehitystyötä kannattaisi tulevaisuudessa jatkaa.

Weldability of powder bed fusion fabricated stainless steel 316L sheets to cold rolled sheet metal

Weldability of powder bed fusion (PBF) fabricated components has come to discussion in past two years due to resent developments in the PBF technology and limited size of the machines used in the fabrication process. This study concentrated on effects of energy input of welding on mechanical properties and microstructural features of welds between PBF fabricated stainless steel 316L sheets and cold rolled sheet metal of same composition by the means of destructive testing and microscopic analysis. Optical fiber diameter, laser power and welding speed were varied during the experiments that were executed following one variable at a time (OVAT) method. One of the problems of welded PBF fabricated components has been lower elongations at break comparing to conventionally manufactured components. Decreasing energy input of the laser keyhole welding decreased elongations at break of the welded specimens. Ultimate tensile strengths were not affected significantly by the energy input of the welding, but fracturing of the specimens welded using high energy input occurred from the weld metal. Fracturing of the lower energy input welds occurred from the PBF fabricated base metal. Energy input was found to be critical factor for mechanical properties of the welds. Multioriented grain growth and formation of neck at fusion zone boundary on the cold rolled side of the weld was detected and suspected to be result from weld pool flows caused by differences in molten weld pool behaviour between the PBF fabricated and cold rolled sides of the welds.

Kuparin hitsaus kattavilla laatuvaatimuksilla

Kuparin ja kupariseosten hitsaus eroaa merkittävästi esimerkiksi terästen hitsauksesta. Suuri lämmönjohtavuus, lämpölaajeneminen, pehmeneminen ja kuparin taipumus liuottaa kaasuja sulaan asettavat hitsaukselle haasteita. Kuparia on perinteisesti hitsattu kaasuhitsaamalla ja kaasukaarihitsausprosesseilla, mutta uudemmat menetelmät kuten laserhitsaus, elektronisuihkuhitsaus ja FSW-hitsaus tarjoavat uudenlaisia käyttökohteita korkealla laadulla. ISO 3834-2 asettaa noudatettavat vaatimukset hitsaustoiminnalle laatuvaatimusten ollessa kattavia. Ydinvoimalaitoksella hitsauksessa tulee lisäksi noudattaa Säteilyturvakeskuksen YVL-ohjeita, joissa on määritetty lisävaatimuksia liitosten materiaalivalinnoille, pätevöittämiselle ja tarkastamiselle. Tässä työssä tutkittiin kuparimetallien hitsauksen mahdollisuutta Loviisan ydinvoimalaitoksella juottamisen sijasta siten, että kattavat laatuvaatimukset täyttyisivät. Hitsauskokeissa ja laboratoriotutkimuksissa testattiin hitsausta erilaisilla hitsausaineilla ja hitsausprosesseilla. Koetulosten pohjalta toteutettiin hitsausmenetelmä deoksidoidun kupariputken ja tinapronssilaipan TIG-hitsaukselle.

Evaluation of the quality of a molded sweet biscuit enriched with okara flour

The objective of this research was to test the addition of soymilk residue, also known as okara, to a molded sweet biscuit (MSB). The okara was provided by two soymilk producing companies whose production systems are based on hot disintegration of decorticated (company B) or non-decorticated (company A) soybeans and separation of the soymilk. Okaras A and B were dehydrated in a flash dryer and then ground to a flour (< 200 mesh). The okara flours showed high protein (35 g.100 g-1 dwb), lipid (17 g.100 g-1 dwb), and fiber (17 to 21 g.100 g-1 dwb) contents. The water holding capacity, protein solubility, emulsifying capacity, emulsion stability and isoflavone contents found in flour A were significantly higher (p < 0.05) than in flour B. The formulation of MSB, replacing 30% (w/w) of the wheat flour with okara flour was tested. The results of the physical measurements, brittleness and water activity of the MSB with flours A and B did not differ significantly (p < 0.05) from those of the standard. The color, flavor and overall quality of the MSB with 30% of okara flour B did not differ significantly from those of the standard biscuit, demonstrating its potential for application in confectionery products.

Physical, chemical, technological and sensory characteristics of Frankfurter type sausage containing okara flour

The addition of okara flour to an emulsified meat product (Frankfurter type sausage) was evaluated based on the physical, chemical, technological, and sensory characteristics of the final product. Okara, residue from soymilk production, was provided by two soymilk producing companies whose production systems were based on the hot disintegration of the decorticated (company B) or undecorticated (company A) soybeans. The okara was dehydrated using a flash dryer and then ground into flour (>420 µm). However, The okara flours A and B showed approximately the same amount of protein (35 and 40 g.100 g-1 dwb). However, the okara flour A presented higher values (p < 0.05) for all technological functional properties studied (emulsification capacity, emulsion stability, protein solubility, and water hold capacity) than those of okara flour B. The A and B okara flours were used in a frankfurter sausage formulation as substitution of 1.5% and 4% of meat. The results showed that the sausages containing okara flours A and B, as well as the control sausage, were accepted by the sensory panel. Moreover, there were no significant differences (p < 0.05) in the physical (color, objective texture, and emulsion stability) and chemical (pH and proximate composition) measurements of the sausages with and without the okara flour.

Effects of micronized sodium chloride on the sensory profile and consumer acceptance of turkey ham with reduced sodium content

The impact of sodium chloride reduction and its substitution for micronized salt on consumer acceptance of turkey ham was investigated. Five formulations - F1 (control - 2.0% NaCl), F2 (1.7% NaCl), F3 (1.4% NaCl), F4 (1.7% micronized NaCl), and F5 (1.4% micronized NaCl) - were evaluated with respect to sodium chloride content and by consumers using a nine-point hedonic scale for overall acceptability and CATA (check-all-that-apply) using 24 sensory descriptors. Trained panelists characterized the products using the flash profiling technique. Reductions in the salt content by up to 30% did not affect the overall acceptability of the samples by the consumers. However, the consumers characterized the formulations with lower salt content as "less salty and less seasoned" in comparison to the contents in the control. Products containing 1.7% NaCl were considered very similar to the control. The results obtained indicate that it is possible to reduce NaCl content by 30% without affecting consumer acceptance of the product. The use of micronized salt did not affect the sensory characteristics when compared with those of formulations containing the same level of sodium chloride indicating that micronized salt does not influence perception of salt.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Robottihitsauksen toimintojen kehittäminen hitsaustuotannossa

Tämän diplomityön tarkoituksena oli kehittää robottihitsauksen toimintoja KKR Steel Oy:ssä. Tärkeimmät tutkimuskohteet olivat robottisolujen toiminnan tehostaminen ja uusien robottihitsaukseen sopivien tuotteiden kartoittaminen. Työ on jaettu teoreettiseen ja käytännön osuuteen. Teoriaosassa perehdytään kirjallisuuskatsauksen kautta robottihitsauksen perusteisiin, hitsauksen robotisointiin sekä tuottavuuteen ja laatuun. Robottihitsauksen osuudessa käsitellään hitsausrobotin rakennetta, siihen liittyviä oheislaitteita ja robottien ohjelmointia. Hitsauksen robotisoinnissa selvitetään syitä robottihitsauksen käyttöönotolle, robotisoitavilta tuotteilta vaadittavia ominaisuuksia sekä erilaisia toimenpiteitä robottiaseman toiminnan tehostamiseksi. Tuottavuuteen liittyvässä osuudessa selvitetään erilaisten laskentakaavojen ja tunnuslukujen käyttöä ja merkitystä hitsauksessa. Käytännön osuudessa kartoitettiin yrityksen robottihitsauksen lähtötilanne ja selvitettiin ongelmakohtien perusteella kehittämistoimenpiteitä. Tutkimuksissa seurattiin ja havainnoitiin hitsaustuotannon eri vaiheita, minkä perusteella laadittiin erilaisia parannuskeinoja. Toimenpiteistä saatavan hyödyn arviointiin käytettiin yrityksen tuotantoon sopivia mittareita kuten läpimenoaikaa ja kaariaikasuhdetta. Havaittujen ongelmakohtien perusteella ryhdyttiin kehittämään hitsauskiinnittimien suunnittelua ja käsittelylaitteiden käyttöä hitsaustuotannossa sekä hyödyntämään etäohjelmointia tuotteiden viennissä robottiasemille. Lisäksi robottiasemien käyttöastetta pyrittiin nostamaan tutkimalla käsinhitsattavia tuotteita ja siirtämällä niistä robotille soveltuvimmat robottiasemille hitsattavaksi.

Stromal interaction molecule 1 and its role in the regulation, proliferation and protein expression in follicular ML-1 thyroid cancer cells

Calcium (Ca2+) is involved in the regulation of variety of cellular functions including hallmarks of cancer development such as cellular migration and cellular proliferation. Store-operated calcium entry (SOCE) is a central mechanism in cellular calcium signaling and in maintaining the cellular calcium balance. Stromal interaction molecule 1(STIM1) has been identified as an important constituent of SOCE. In this thesis , the STIM1 proteins are studied for their importance in cellular processes and their effects on the expression of S1P1, S1P2, S1P3, VEGFR-2, and TRPC-1 in follicular ML-1 thyroid cancer cells. The results show the importance of STIM1 proteins in SOCE in these cells. The SOCE is significantly reduced in the STIM1 knockdown cells. The results also show the importance of STIM1 proteins in the expression of S1P2 and VEGFR-2 in these cells, as knockdown of STIM1 was shown to upregulate the expression of S1P2 and VEGFR-2. The migration and proliferation is also considerably reduced in the cells in which STIM1 has been knocked down showing the significance of STIM1 in the migration and proliferation in these cells.

Modifioidun MAG-kaarihitsausprosessin hyödyntäminen railotilavuuden pienentämisessä mekanisoidussa orbitaalihitsauksessa.

Länsimaisen työn hinta luo jatkuvan paineen hitsauksen tuottavuuden parantamiseen. MIG/MAG-hitsauksen tuottavuutta voidaan parantaa tehostamalla hitsausprosessia, vähentämällä hitsien lukumäärää ja pienentämällä hitsiaineen tarvetta. Eri virtalähdevalmistajat tuovat markkinoille hitsausprosesseja hitsauksen tehostamiseen, joilla pystytään korvata vähemmän tuottavia hitsaustyövaiheita. Hitsien lukumäärän vähentäminen on rakenteen suunnitteluun liittyvä tekijä ja hitsiaineen tarpeen pienentäminen voidaan toteuttaa railogeometrian muutoksilla tai tuotteen sopivalla suunnittelulla. Diplomityössä on tutkittu 30 mm paksujen S355 rakenneteräsputkien hitsauksen tuottavuuden kasvattamista käyttäen nykyaikaisia modifioituja kaarihitsausprosesseja ja railotilavuutta pienentämällä. Työssä vertailtiin 30o ja 60o railokulmalla tehtyjä liitoksia. Railogeometrian muutoksen lisäksi diplomityössä vertailtiin eri menetelmien tehokkuutta putken pohjapalon hitsauksessa.

Weldability of high strength aluminium alloys

The need for reduced intrinsic weight of structures and vehicles in the transportation industry has made aluminium research of interest. Aluminium has properties that are favourable for structural engineering, including good strength-to-weight ratio, corrosion resistance and machinability. It can be easily recycled saving energy used in smelting as compared to steel. Its alloys can have ultimate tensile strength of up to 750 MPa, which is comparable to steel. Aluminium alloys are generally weldable, however welding of high strength alloys like the 7xxx series pose considerable challenges. This paper presents research on the weldability of high strength aluminium alloys, principally the 7xxx series. The weldability with various weld processes including MIG, TIG, and FSW, is discussed in addition to consideration of joint types, weld defects and recommendations for minimizing or preventing weld defects. Experimental research was carried out on 7025-T6 and AW-7020 alloys. Samples were welded, and weld cross sections utilized in weld metallurgy studies. Mechanical tests were carried out including hardness tests and tensile tests. In addition, testing was done for the presence of Al2O3 on exposed aluminium alloy. It was observed that at constant weld heat input using a pulsed MIG system, the welding speed had little or no effect on the weld hardness. However, the grain size increased as the filler wire feed rate, welding current and welding speed increased. High heat input resulted in lower hardness of the weld profile. Weld preheating was detrimental to AW- 7020 welds; however, artificial aging was beneficial. Acceptable welds were attained with pulsed MIG without the removal of the Al2O3 layer prior to welding. The Al2O3 oxide layer was found to have different compositions in different aluminium alloys. These findings contribute useful additional information to the knowledge base of aluminium welding. The application of the findings of this study in welding will help reduce weld cost and improve high strength aluminium structure productivity by removing the need for pre-weld cleaning. Better understanding of aluminium weld metallurgy equips weld engineers with information for better aluminium weld design.

Effects of Fabrication Processes on the Behavior of S960 Ultra High Strength Steel (UHSS)

Strenx® 960 MC is a direct quenched type of Ultra High Strength Steel (UHSS) with low carbon content. Although this material combines high strength and good ductility, it is highly sensitive towards fabrication processes. The presence of stress concentration due to structural discontinuity or notch will highlight the role of these fabrication effects on the deformation capacity of the material. Due to this, a series of tensile tests are done on both pure base material (BM) and when it has been subjected to Heat Input (HI) and Cold Forming (CF). The surface of the material was dressed by laser beam with a certain speed to study the effect of HI while the CF is done by bending the specimen to a certain angle prior to tensile test. The generated results illustrate the impact of these processes on the deformation capacity of the material, specially, when the material has HI experience due to welding or similar processes. In order to compare the results with those of numerical simulation, LS-DYNA explicit commercial package has been utilized. The generated results show an acceptable agreement between experimental and numerical simulation outcomes.