Estudio experimental sobre la efectividad y la viabilidad de distintas soluciones constructivas para reducir la concentración de gas radón en edificaciones

El trabajo de investigación desarrollado que ha dado lugar a la realización de esta Tesis, aborda la protección de los edificios frente a la entrada de gas radón y su acumulación en los espacios habitados. Dicho gas (isótopo del radón Rn-222) es un elemento radiactivo que se genera, principalmente, en terrenos con altos contenidos de radio (terrenos graníticos por ejemplo). Su alto grado de movilidad permite que penetre en los edificios a través de los materiales de cerramiento del mismo (porosidad de los materiales, fisuras, grietas y juntas) y se acumule en su interior, donde puede ser inhalado en altas concentraciones. La Organización Mundial de la Salud, califica al radón como agente cancerígeno de grado 1. Según este Organismo, el radón es la segunda causa de contracción de cáncer pulmonar detrás del tabaco. Como respuesta a esta alarma, distintos estados ya han elaborado normativas en las que se proponen soluciones para que los niveles de concentración de radón no superen los valores recomendados por los organismos internacionales responsables de la protección radiológica. En España aún no existe normativa de protección frente a este agente cancerígeno causante de numerosas muertes, y es por tal motivo evidente la necesidad de aportar documentación técnica que ayude a las administraciones nacionales y locales a desarrollar dicha normativa para ajustarse a las recomendaciones europeas e internacionales sobre los niveles que no se deben superar y que, por otro lado, ya han contemplado una gran cantidad de países. Como principal aportación de este trabajo se muestran los resultados de reducción de concentración de gas radón de distintas soluciones constructivas enfocadas a frenar la entrada de gas radón al interior de los edificios haciendo uso de técnicas y materiales habituales en el ámbito de la construcción en España. Para ello, se han estudiado las efectividades de dichas soluciones, en lo referente a su capacidad para frenar la inmisión de radón, en un prototipo de vivienda construido al efecto en un terreno con altas concentraciones de radón. Las soluciones propuestas y ensayadas han sido el resultado de una labor de optimización de los sistemas estudiados en la bibliografía con el fin de adaptar las técnicas a los sistemas constructivos habituales en España y en concreto a la situación real del prototipo de vivienda construido en un lugar con contenidos de radón en terreno muy elevados. El trabajo incluye un capítulo inicial con los conceptos básicos necesarios para entender la problemática que supone habitar en espacios con altos contenidos de radón. ABSTRACT The research developed, which has led to the completion of this thesis, deal with the protection of buildings against entry of radon gas and its accumulation in the ocupated spaces. This gas (radon isotope Rn-222) is a radioactive element generated, mainly, in areas with high levels of radio (granitic terrain for example). Its high mobility allows entering in buildings through the enclosure materials of it (porosity of materials, cracks, crevices and joints) and accumulates inside, where it can be inhaled in high concentrations. The World Health Organization describes radon gas as a carcinogen agent in level 1. According to this Agency, radon is the second leading cause of lung cancer behind tobacco. In response to this alarm, some states have developed regulations that propose solutions to reduce radon concentration levels for not exceeding the values recommended by international agencies responsible in radiation protection. In Spain there is still no legislation to protect against this carcinogen element that cause numerous deaths, and for that reason it is evident the need to provide technical documentation to help the national and local governments to develop legislation for reaching the European and international levels recommendations. As the main contribution of this work are the results of reducing radon concentration using different constructive solutions aimed to stop radon entry in buildings, with techniques and materials common in Spain. To do this, effectiveness of such solutions, have been studied in terms of its ability to stop radon entry in a housing prototype built for this purpose in an area with high radon levels. The solutions proposed and tested have been the result of a process of optimization of systems studied in the literature in order to adapt the techniques to Spanish building material and, specifically, to the actual situation of housing prototype built in a place with high contents of radon in soil. The work includes an initial chapter with the basic concepts needed to understand the problem of living in areas with high levels of radon.

Development of FEM/BEM and SEA models from experimental results for structural elements with attached equipment

This work focuses on the analysis of a structural element of MetOP-A satellite. Given the special interest in the influence of equipment installed on structural elements, the paper studies one of the lateral faces on which the Advanced SCATterometer (ASCAT) is installed. The work is oriented towards the modal characterization of the specimen, describing the experimental set-up and the application of results to the development of a Finite Element Method (FEM) model to study the vibro-acoustic response. For the high frequency range, characterized by a high modal density, a Statistical Energy Analysis (SEA) model is considered, and the FEM model is used when modal density is low. The methodology for developing the SEA model and a compound FEM and Boundary Element Method (BEM) model to provide continuity in the medium frequency range is presented, as well as the necessary updating, characterization and coupling between models required to achieve numerical models that match experimental results.

Crack width control in RC elements with recycled steel fibres and applications to integral structures : theoretical and experimental study

El presente trabajo trata de elementos reforzados con barras de armadura y Fibras Metálicas Recicladas (FMR). El objetivo principal es mejorar el comportamiento a fisuración de elementos sometidos a flexión pura y a flexión compuesta, aumentando en consecuencia las prestaciones en servicio de aquellas estructuras con requerimientos estrictos con respecto al control de fisuración. Entre éstas últimas se encuentran las estructuras integrales, es decir aquellas estructuras sin juntas (puentes o edificios), sometidas a cargas gravitatorias y deformaciones impuestas en los elementos horizontales debidas a retracción, fluencia y temperatura. Las FMR son obtenidas a partir de los neumáticos fuera de uso, y puesto que el procedimiento de reciclado se centra en el caucho en vez que en el acero, su forma es aleatoria y con longitud variable. A pesar de que la eficacia del fibrorefuerzo mediante FMR ha sido demostrada en investigaciones anteriores, la innovación que representa este trabajo consiste en proponer la acción combinada de barras convencionales y FMR en la mejora del comportamiento a fisuración. El objetivo es por tanto mejorar la sostenibilidad del proyecto de la estructura en HA al utilizar materiales reciclados por un lado, y aumentando por el otro la durabilidad. En primer lugar, se presenta el estado del arte con respecto a la fisuración en elementos de HA, que sucesivamente se amplía a elementos reforzados con barras y fibras. Asimismo, se resume el método simplificado para el análisis de columnas de estructuras sin juntas ya propuesto por Pérez et al., con particular énfasis en aquellos aspectos que son incompatibles con la acción de las fibras a nivel seccional. A continuación, se presenta un modelo para describir la deformabilidad seccional y la fisuración en elementos en HA, que luego se amplía a aquellos elementos reforzados con barras y fibras, teniendo en cuenta también los efectos debidos a la retracción (tension stiffening negativo). El modelo es luego empleado para ampliar el método simplificado para el análisis de columnas. La aportación consiste por tanto en contar con una metodología amplia de análisis para este tipo de elementos. Seguidamente, se presenta la campaña experimental preliminar que ha involucrado vigas a escala reducida sometidas a flexión simple, con el objetivo de validar la eficiencia y la usabilidad en el hormigón de las FMR de dos diferentes tipos, y su comportamiento con respecto a fibras de acero comerciales. Se describe a continuación la campaña principal, consistente en ensayos sobre ocho vigas en flexión simple a escala 1:1 (variando contenido en FRM, Ø/s,eff y recubrimiento) y doce columnas a flexión compuesta (variando contenido en FMR, Ø/s,eff y nivel de fuerza axil). Los resultados obtenidos en la campaña principal son presentados y comentados, resaltando las mejoras obtenidas en el comportamiento a fisuración de las vigas y columnas, y la rigidez estructural de las columnas. Estos resultados se comparan con las predicciones del modelo propuesto. Los principales parámetros estudiados para describir la fisuración y el comportamiento seccional de las vigas son: la separación entre fisuras, el alargamiento medio de las armaduras y la abertura de fisura, mientras que en los ensayos de las columnas se ha contrastado las leyes momento/curvatura, la tensión en las barras de armadura y la abertura de fisura en el empotramiento en la base. La comparación muestra un buen acuerdo entre las predicciones y los resultados experimentales. Asimismo, se nota la mejora en el comportamiento a fisuración debido a la incorporación de FMR en aquellos elementos con cuantías de armadura bajas en flexión simple, en elementos con axiles bajos y para el control de la fisuración en elementos con grandes recubrimientos, siendo por tanto resultados de inmediato impacto en la práctica ingenieril (diseño de losas, tanques, estructuras integrales, etc.). VIIIComo punto final, se presentan aplicaciones de las FMR en estructuras reales. Se discuten dos casos de elementos sometidos a flexión pura, en particular una viga simplemente apoyada y un tanque para el tratamiento de agua. En ambos casos la adicción de FMR al hormigón lleva a mejoras en el comportamiento a fisuración. Luego, utilizando el método simplificado para el análisis en servicio de columnas de estructuras sin juntas, se calcula la máxima longitud admisible en casos típicos de puentes y edificación. En particular, se demuestra que las limitaciones de la práctica ingenieril actual (sobre todo en edificación) pueden ser aumentadas considerando el comportamiento real de las columnas en HA. Finalmente, los mismos casos son modificados para considerar el uso de MFR, y se presentan las mejoras tanto en la máxima longitud admisible como en la abertura de fisura para una longitud y deformación impuesta. This work deals with elements reinforced with both rebars and Recycled Steel Fibres (RSFs). Its main objective is to improve cracking behaviour of elements subjected to pure bending and bending and axial force, resulting in better serviceability conditions for these structures demanding keen crack width control. Among these structures a particularly interesting type are the so-called integral structures, i.e. long jointless structures (bridges and buildings) subjected to gravitational loads and imposed deformations due to shrinkage, creep and temperature. RSFs are obtained from End of Life Tyres, and due to the recycling process that is focused on the rubber rather than on the steel they come out crooked and with variable length. Although the effectiveness of RSFs had already been proven by previous research, the innovation of this work consists in the proposing the combined action of conventional rebars and RSFs to improve cracking behaviour. Therefore, the objective is to improve the sustainability of RC structures by, on the one hand, using recycled materials, and on the other improving their durability. A state of the art on cracking in RC elements is firstly drawn. It is then expanded to elements reinforced with both rebars and fibres (R/FRC elements). Finally, the simplified method for analysis of columns of long jointless structures already proposed by Pérez et al. is resumed, with a special focus on the points that conflict when taking into account the action of fibres. Afterwards, a model to describe sectional deformability and cracking of R/FRC elements is presented, taking also into account the effect of shrinkage (negative tension stiffening). The model is then used to implement the simplified method for columns. The novelty represented by this is that a comprehensive methodology to analyse this type of elements is presented. A preliminary experimental campaign consisting in small beams subjected to pure bending is described, with the objective of validating the effectiveness and usability in concrete of RSFs of two different types, and their behaviour when compared with commercial steel fibres. With the results and lessons learnt from this campaign in mind, the main experimental campaign is then described, consisting in cracking tests of eight unscaled beams in pure bending (varying RSF content, Ø/s,eff and concrete cover) and twelve columns subjected to imposed displacement and axial force (varying RSF content, Ø/s,eff and squashing load ratio). The results obtained from the main campaign are presented and discussed, with particular focus on the improvement in cracking behaviour for the beams and columns, and structural stiffness for the columns. They are then compared with the proposed model. The main parameters studied to describe cracking and sectional behaviours of the beam tests are crack spacing, mean steel strain and crack width, while for the column tests these were moment/curvature, stress in rebars and crack with at column embedment. The comparison showed satisfactory agreement between experimental results and model predictions. Moreover, it is pointed out the improvement in cracking behaviour due to the addition of RSF for elements with low reinforcement ratios, elements with low squashing load ratios and for crack width control of elements with large concrete covers, thus representing results with a immediate impact in engineering practice (slab design, tanks, integral structures, etc.). Applications of RSF to actual structures are finally presented. Two cases of elements in pure bending are presented, namely a simple supported beam and a water treatment tank. In both cases the addition of RSF to concrete leads to improvements in cracking behaviour. Then, using the simplified model for the serviceability analysis of columns of jointless structures, the maximum achievable jointless length of typical cases of a bridge and building is obtained. In XIIparticular, it is shown how the limitations of current engineering practice (this is especially the case of buildings) can be increased by considering the actual behaviour of RC supports. Then, the same cases are modified considering the use of RSF, and the improvements both in maximum achievable length and in crack width for a given length and imposed strain at the deck/first floor are shown.

Experimental investigation of dynamic pressure loads during dam break

The objectives of this work are to revisit the experimental measurements on dam break flow over a dry horizontal bed and to provide a detailed insight into the dynamics of the dam break wave impacting a vertical wall downstream the dam, with emphasis on the pressure loads. The measured data are statistically analyzed and critically discussed. As a result, an extensive set of data for validation of computational tools is provided.

Experimental verification of intermediate band formation on titanium-implanted silicon

Intermediate band formation on silicon layers for solar cell applications was achieved by titanium implantation and laser annealing. A two-layer heterogeneous system, formed by the implanted layer and by the un-implanted substrate, was formed. In this work, we present for the first time electrical characterization results which show that recombination is suppressed when the Ti concentration is high enough to overcome the Mott limit, in agreement with the intermediate band theory. Clear differences have been observed between samples implanted with doses under or over the Mott limit. Samples implanted under the Mott limit have capacitance values much lower than the un-implanted ones as corresponds to a highly doped semiconductor Schottky junction. However, when the Mott limit is surpassed, the samples have much higher capacitance, revealing that the intermediate band is formed. The capacitance increasing is due to the big amount of charge trapped at the intermediate band, even at low temperatures. Ti deep levels have been measured by admittance spectroscopy. These deep levels are located at energies which vary from 0.20 to 0.28?eV below the conduction band for implantation doses in the range 1013-1014 at./cm2. For doses over the Mott limit, the implanted atoms become nonrecombinant. Capacitance voltage transient technique measurements prove that the fabricated devices consist of two-layers, in which the implanted layer and the substrate behave as an n+/n junction.

Experimental confirmation of FK concentrator insensitivity to chromatic aberrations

The FK concentrator has demonstrated during the last years that compares very well with other Fresnel-based concentrator optics for CPV. There are several features that provide the FK high performance: (1) high optical efficiency; (2) large tolerance to tracking misalignment and manufacturing errors, thanks to a high CAP (Concentration-Acceptance Product); (3) good irradiance uniformity and low chromatic dispersion on the cell surface. Non-uniformities in terms of absolute irradiance and spectral content produced by conventional CPV systems can originate electrical losses in multi-junction (MJ) solar cells. The aim of this work is to analyze the influence of these non-uniformities in the FK concentrator performance and how FK concentrator provides high electrical efficiencies thanks to its insensitivity to chromatic aberrations, especially when components move away from the module nominal position due to manufacturing misalignments. This analysis has been done here by means of both, experimental on-sun measurements and simulations based on 3D fully distributed circuit model for MJ cells.

An experimental and numerical study of the pattern of cracking of concrete due to steel reinforcement corrosion

In this work, cracking of concrete due to steel reinforcement corrosion is experimentally and numerically studied. The tests combined accelerated corrosion—to generate the cracks—with impregnation under vacuum with resin containing fluorescein—to enhance their visibility under ultraviolet light. In parallel, a model—called expansive joint element—was developed to simulate the expansion of the oxide and finite elements with an embedded adaptable cohesive crack were used to describe concrete cracking. The results show that a good agreement exists between the experimental and numerical crack patterns, which constitutes promising progress towards a comprehensive understanding of corrosion-induced cracking in reinforced concrete.

Modelization of an experimental solar test box equipped with a water-flow based window

A study on a water- ow window installed in a test box is presented. This window is composed of two glass panes separated by a chamber through water ows. The ow of water comes from an isolated tank which contains heat water. In order to fully evaluate the water- ow window performance for different room and window sizes, locations and weather conditions, a mathematical model of the whole box is needed. The proposed model, in which conduction heat transfer mechanism is the only considered, is one dimensional and unsteady based upon test box energy balance. The effect of the heat water tank, which feeds the water- ow window, is included in the model by means of a time delay in the source term. Although some previous work about moving uid chamber has been developed, air was used as heat transfer uid and no uid storage was considered. Finally a comparison between the numerical solution and the obtained experimental data is done.

On-the-fly dynamic reprogramming mechanism for increasing the energy efficiency and supporting multi-experimental capabilities in WSNs

Remote reprogramming capabilities are one of the major concerns in WSN platforms due to the limitations and constraints that low power wireless nodes poses, especially when energy efficiency during the reprogramming process is a critical factor for extending the battery life of the devices. Moreover, WSNs are based on low-rate protocols in which as greater the amount of data is sent, the more the possibility to lose packets during the transmitting process is. In order to overcome these limitations, in this work a novel on-the-fly reprogramming technique for modifying and updating the application running on the wireless sensor nodes is designed and implemented, based on a partial reprogramming mechanism that significantly reduces the size of the files to be downloaded to the nodes, therefore diminishing their power/time consumption. This powerful mechanism also addresses multi-experimental capabilities because it provides the possibility to download, manage, test and debug multiple applications into the wireless nodes, based on a memory map segmentation of the core. Being an on-the-fly reprogramming process, no additional resources to store and download the configuration file are needed.

Testing the performance of a green wall system on an experimental building in the summer

It is known that a green wall brings some advantages to a building. It constitutes a barrier against solar radiation, thus decreasing and delaying the incoming heat flux. The aim of this study is to quantify such advantages through analytical comparison between two facades, a vegetal facade and a conventional facade. Both were highly insulated (U-value = 0.3 W/m2K) and installed facing south on the same building in the central territory of Spain. In order to compare their thermal trend, a series of sensors were used to register superficial and indoor air temperature. The work was carried out between 17th August 2012 and 1st October 2012, with a temperature range of 12°C-36°C and a maximum horizontal radiation of 1020 W/m2. Results show that the indoor temperature of the green wall module was lower than the other. Besides, comparing superficial outdoor and indoor temperatures of the two walls to outdoor air temperatures, it was noticed that, due to the shading plants, the green wall superficial temperature was 5 °C lower on the facade, while the bare wall temperature was 15 °C higher. The living wall module temperature was 1.6 °C lower than the outdoor, while the values of the conventional one were similar to the outdoor air temperature.

Heat losses in a CVD reactor for polysilicon: comprehensive model and experimental validation

This work addresses heat losses in a CVD reactor for polysilicon production. Contributions to the energy consumption of the so-called Siemens process are evaluated, and a comprehensive model for heat loss is presented. A previously-developed model for radiative heat loss is combined with conductive heat loss theory and a new model for convective heat loss. Theoretical calculations are developed and theoretical energy consumption of the polysilicon deposition process is obtained. The model is validated by comparison with experimental results obtained using a laboratory-scale CVD reactor. Finally, the model is used to calculate heat consumption in a 36-rod industrial reactor; the energy consumption due to convective heat loss per kilogram of polysilicon produced is calculated to be 22-30 kWh/kg along a deposition process.

A Semantic-Based Approach to Attain Reproducibility of Computational Environments in Scientic Work ows: A Case Study

Reproducible research in scientic work ows is often addressed by tracking the provenance of the produced results. While this approach allows inspecting intermediate and nal results, improves understanding, and permits replaying a work ow execution, it does not ensure that the computational environment is available for subsequent executions to reproduce the experiment. In this work, we propose describing the resources involved in the execution of an experiment using a set of semantic vocabularies, so as to conserve the computational environment. We dene a process for documenting the work ow application, management system, and their dependencies based on 4 domain ontologies. We then conduct an experimental evaluation sing a real work ow application on an academic and a public Cloud platform. Results show that our approach can reproduce an equivalent execution environment of a predened virtual machine image on both computing platforms.

Casa Huarte: José Antonio Corrales y Ramón Vázquez Molezún. El concepto de lo experimental en el ámbito doméstico

Se plantea aquí el estudio de la Casa Huarte (1966) como un experimento doméstico -así lo concibió el matrimonio Huarte desde la libertad de acción y la entrega al talento de los arquitectos- que sintetizó los principios de los proyectos de la primera etapa de la obra de José Antonio Corrales (1921-2010) y Ramón Vázquez Molezún (1922-1993): paisaje construido, topografía modificada, basamento pesado y arraigado, cubierta ligera flotante y abstracción compositiva. La considerada vivienda experimental del siglo XX estaba asociada a estructuras familiares reducidas, como mucho formadas por un matrimonio con dos hijos. La Casa Huarte, sin embargo, pertenece a un grupo no reconocido de viviendas experimentales de gran formato, que aportaban -en entornos de vida socio-familiar no convencionales- una complejidad funcional, espacial y de relaciones interpersonales que la vivienda mínima no tenía. La Casa Huarte supuso un punto de inflexión en la carrera de Corrales y Molezún, culminando una primera etapa donde se concentraron sus obras más destacadas: Instituto en Herrera de Pisuerga (1956), Residencia de Miraflores (1958) y Pabellón de Bruselas, en sus versiones belga (1958) y española (1959). El proyecto de la Casa Huarte adelantó estrategias que aplicarían en proyectos posteriores -dinamismo del plano horizontal, visuales diagonales, entrada tangencial- y culminó la evolución de un tipo de vivienda que Corrales y Molezún comenzaron a investigar diez años antes. Entre 1956 y 1961 proyectaron cuatro viviendas (Casa Remírez Escudero, Casa Álvarez Mon, Casa Gómez Acebo y Casa Cela) que anticiparon soluciones y situaciones presentes y perfeccionadas en la Casa Huarte. Corrales aseguraba que si la vida es contradictoria la arquitectura también debería serlo. La Casa Huarte es compleja y contradictoria funcional y espacialmente, homogeneizada por una imagen exterior rotunda y atractiva de juegos de volúmenes maclados. El proyecto se muestra así de contundente detrás de habilidosas maniobras tectónicas que ocultan las muchas complejidades y contradicciones aparentemente inapreciables. Estas maniobras confunden la imagen que de la casa se tiene. Debajo de su manto cerámico de reminiscencias vernáculas - híbrido de casa castellana y arquitectura nórdica- se esconde una obra de arquitectura avanzada tecnológicamente. La tesis se desarrolla en cuatro apartados denominados procesos, por lo que tienen de secuencia en el desarrollo de la investigación. Estos procesos son: proceso descriptivo, proceso analítico, proceso interpretativo y proceso poético. Después del necesario e introductorio proceso descriptivo, el cuerpo central de la tesis -que contiene los procesos analítico, interpretativo y poético- sigue un guión marcado por la defensa de la categoría experimental de la Casa Huarte. Se han tratado los conceptos más característicos de la vivienda, desde los más generales a los más específicos divididos en cuatro grupos: Composición, volumen y espacio; El patio como lugar; El jardín: horizonte construido; Domesticidad del mundo interior; y Euritmia: materia y espíritu Molezún aseguraba que para entender una obra de arquitectura había que dibujarla. La Casa Huarte ha sido redibujada en sus tres etapas fundamentales: el proyecto de ejecución (marzo 1965), la casa acabada (noviembre 1966) y el estado actual (2012). El estudio y análisis se centra en la casa construida, por ser la realidad tridimensional en que el proyecto se nos manifiesta. La documentación gráfica del estado actual de la vivienda es inédita y ha sido posible gracias a múltiples inspecciones de la Casa Huarte en visitas facilitadas por las hijas de Jesús Huarte, actuales propietarias de la vivienda. Esta documentación nos permite constatar las alteraciones sobre la obra construida y conocer que modificaciones serían necesarias para recuperar el estado original de la casa. La Casa Huarte es una obra singular, una de las cinco viviendas unifamiliares pertenecientes a la Arquitectura del Movimiento Moderno en España y Portugal de mayor interés registrada por el Docomomo Internacional. Su futuro es incierto, se encuentra deshabitada y en venta. La familia Huarte ha cumplido con creces la misión de conservar su patrimonio. Es pertinente reivindicar su vigencia como obra de referencia de la arquitectura española del siglo XX, y, de esa manera, evitar que caiga en el olvido y el abandono. ABSTRACT The Huarte House (1966) will be analysed as a domestic experiment – that is how the Huarte’s conceived it, putting their faith in the architects – that synthesized the principles from the projects of the first phase of the work of Jose Antonio Corrales (1921-2010) and Ramón Vázquez Molezún (1922-1993): built landscape, modified topography, heavy and rooted base, light, floating roof and abstraction in composition. The experimental house of the 20th century was associated with small nuclear families of at the most a couple and two children. The Huarte House belongs to a group of non-recognised experimental houses of a larger size -and more unconventional familial settings- that lent themselves to greater functional, spatial and interpersonal complexity than their smaller counterparts. The Huarte House represented a turning point in the careers of Corrales and Molezún, capping a first phase that includes their most prominent work: the Institute at Herrera de Pisuerga (1965), the Residence at Miraflores (1958) and the Brussels Pavilion, in its Belgian (1958) and Spanish (1959) version. The project for the Huarte house anticipated strategies which they would apply to later projects: dynamism of the horizontal plane, diagonal visuals, and tangential entrances. It was also the culmination of the evolution of a type of house that Corrales and Molezún had started to investigate ten years earlier. Between 1956 and 1961 they designed four houses (Ramírez Escudero House, Álvarez Mon House, Gómez Acebo House and Cela House) that anticipated the solutions applied and perfected in the Huarte House. Corrales believed that if life was contradictory architecture should be so too. The Huarte House is complex and contradictory. Corrales and Molezún homogenised the project under a bold and attractive image of intersecting volumes. The project appears emphatic thanks to skilful tectonic manoeuvres that conceal the many complexities and contradictions so that they become imperceptible. These manoeuvres confound the image of the house. Under its ceramic blanket of vernacular reminiscences (a mixture of Castilian house and Nordic architecture) lies a technologically advanced piece of architecture. The thesis is organised in four chapters named ‘processes’ in reference to their sequence in the development of the research. These processes are: descriptive process, analytic process, interpretative process and poetic process. After the necessary and introductory descriptive process, the main body of the thesis, which encompasses the analytical, interpretative and poetic processes, develops the argument for incorporating the Huarte House into the experimental category. The thesis addresses the characteristic concepts of a house, from the general to the more specific, divided in four groups: composition, volume and space; the patio: architecture and landscape; the garden: building the horizon and eurythmy: spirit and matter. Molezún was convinced that to get to know a work of architecture it was necessary to draw it. The Huarte House is redrawn in its three main phases: the executive project (march 1965), the finished house (november 1966) and its actual state (2012). The study and analysis centers on the built house, as the actual tri-dimensional manifestation of the project. The graphic documentation of the present state of the house has never been published before and has been made possible by numerous visits to the House facilitated by Jesus Huarte’s daughters who are the current owners. This documentation allows us to determine any alterations of the constructed work and derive the necessary modifications to bring the house back to its original state. The Huarte House is a unique work, one of five single family homes registered by the International Docomomo. Its future is uncertain. It is currently uninhabited and up for sale. The Huarte family has more than delivered on the mission to safeguard its patrimony. It is important to defend its place as a key work of Spanish architecture of the 20th century and so avoid it being forgotten and abandoned.

Investigación experimental del flujo aerodinámico sobre helipuertos embarcados

La investigación del flujo aerodinámico sobre helipuertos embarcados se encuentra estrechamente relacionada con la operación segura de las aeronaves, pues las condiciones del flujo que tiene lugar en ese entorno pueden exceder los límites para los que están certificadas dichas aeronaves. El ambiente aerodinámico en las inmediaciones de un barco es altamente complejo y se encuentra influenciado por gran número de factores (chimeneas, antenas, mástiles, etc.) relacionados con la configuración específica del propio barco. El flujo objeto de investigación corresponde a la estela que se desarrolla sobre la cubierta de vuelo de una fragata, el cual está fuertemente influenciado por la superestructura de la misma, y que cualitativamente es similar al flujo que tiene lugar entre edificios altos o helipuertos situados en áreas urbanas, pues comprende estructuras tipo caja, con bordes afilados, que generan flujos tridimensionales altamente turbulentos. En esta Tesis se aborda el estudio del problema desde el punto de vista experimental, mediante simulación en túnel aerodinámico y medida de las variables del campo fluido sobre maquetas de fragatas a escala reducida. Las herramientas empleadas para tal cometido, han sido técnicas experimentales, tales como la visualización del flujo, la velocimetría láser por imágenes de partículas, la anemometría láser Doppler y los scanners electrónicos de presión, que han permitido investigar el flujo problema con objeto de obtener información, y adquirir así, un conocimiento más profundo de dicho flujo. La explotación de este conocimiento, ha dado lugar al diseño de una nueva solución, basada en la modificación de geometría básica de la fragata, por medio del cambio de la curvatura del techo del hangar, permitiendo suavizar el escalón descendente que se produce aguas abajo del mismo. Las geometrías modificadas han sido ensayada en túnel mediante la misma metodología empleada para la fragata original, de modo que, ha podido establecerse un análisis comparativo, para valorar la efectividad de la solución propuesta, el cual ha mostrado resultados satisfactorios, retirando el flujo adverso de la zona de operación de helicópteros y desplazándolo hacia el hangar, donde resulta menos peligroso, de modo que se reduce la carga del piloto y los riesgos de accidente durante las operaciones a bordo de embarcaciones. ABSTRACT The investigation of aerodynamic flow above the ship’s heliports is directly related to the aircraft safe operation, because the environment flow conditions may exceed the aircraft certification limits. Aerodynamic ship’s environment is highly complex and it is influenced by a large number of factors (stacks, antennae, masts, …) related to each specific ship configuration. The flow under investigation occurs into the wake produced above the flight deck of a frigate, that is strongly influenced by the superstructure. This flow is similar to one produced around tall buildings or heliports located in urban areas, thus in both of them, the air is flowing around sharp-edges box-like structures, producing three-dimensional and highly turbulent flows. This Thesis studies the problem from an experimental point of view, by means of wind tunnel simulations and measurements of the flow field around reduced scale frigates models. Tools used in this work are the experimental techniques, as flow visualization, particle image velocimetry, laser Doppler anemometry and pressure electronic scanners. These techniques provide information about the flow in order to obtain a more complete insight of this kind of flows. The exploitation of this insight is used for the design of a new flow control concept, based on the modification of the basic frigate geometry. This new design consists in the hangar roof curvature modification that produces a smoothing of the descendent step located downstream the hangar. Modified geometries are tested in wind tunnel by means of the same methodology as the original frigate, thus a comparative analysis is established in order to perform an assessment of effectiveness. This analysis has shown good results in displacing the adverse flow from the helicopter operation path to the nearest hangar region, reducing the pilot load and the accident risks during on board operations.

Validation of the burn-up code EVOLCODE 2.0 with PWR experimental data and with a Sensitivity/Uncertainty analysis

A validation of the burn-up simulation system EVOLCODE 2.0 is presented here, involving the experimental measurement of U and Pu isotopes and some fission fragments production ratios after a burn-up of around 30 GWd/tU in a Pressurized Light Water Reactor (PWR). This work provides an in-depth analysis of the validation results, including the possible sources of the uncertainties. An uncertainty analysis based on the sensitivity methodology has been also performed, providing the uncertainties in the isotopic content propagated from the cross sections uncertainties. An improvement of the classical Sensitivity/ Uncertainty (S/U) model has been developed to take into account the implicit dependence of the neutron flux normalization, that is, the effect of the constant power of the reactor. The improved S/U methodology, neglected in this kind of studies, has proven to be an important contribution to the explanation of some simulation-experiment discrepancies for which, in general, the cross section uncertainties are, for the most relevant actinides, an important contributor to the simulation uncertainties, of the same order of magnitude and sometimes even larger than the experimental uncertainties and the experiment- simulation differences. Additionally, some hints for the improvement of the JEFF3.1.1 fission yield library and for the correction of some errata in the experimental data are presented.