Effect of alkali and alkaline earth fluoride introduction on thermal stability and structure of fluorophosphate glasses

The thermal stability and structure of RF-RF2-AIF(3)-Al(PO3)(3) fluorophosphate glasses were investigated. Analyses of infrared absorbance spectra and Raman spectra reveal that with increasing number of alkali and alkaline earth fluoride components, the sum of P-O-P bond and O-P-O bond increases and glass network is strengthened. Consequently, the inhibition to nucleation and crystallization processes is improved, which is proved by the increment of thermal stability factors AT and S determined by differential scanning calorimetry. In addition, it was found that LiF has poor ability to form glass in univalent alkali fluorides and MgF2 has comparative strong ability to form glass in bivalent alkaline earth fluorides. (c) 2006 Published by Elsevier B.V.

Effect of CdF2 addition on thermal stability and upconversion luminescence properties in Tm3+-Yb3+ codoped oxyfluoride silicate glasses

Tm3+-Yb3+ codoped oxyfluoride silicate glasses suitable for upconversion laser has been fabricated. In this paper, effect of CdF2 addition on thermal stability and upconversion luminescence properties in Tm3+-Yb3+ codoped oxyfluoride silicate glasses have been systematically investigated. The experimental results indicate that, with the substitution CdF2 for PbF2, the glass thermal stability increases and the UV cutoff edge moves to short-wave band slightly. With increasing CdF2 content, the blue and red upconversion luminescence intensity increases slightly at first, and then increases rapidly. While the near infrared (NIR) upconversion emission intensity increases notably at first and then increases slightly. However, the blue and NIR luminescence intensity are much stronger than that of red, indicating these oxyfluoride silicate glasses are more preferable for blue and NIR emissions than red emission. The possible upconversion mechanisms for the blue, red and NIR fluorescence are also estimated and evaluated. (c) 2006 Elsevier B.V. All rights reserved.

熔制条件对铋酸盐玻璃性质的影响

采用传统的玻璃熔融法制备了组成为60Bi2O3-20B2O3-15SiO2-5La2O3(mol%)的铋酸盐玻璃， 系统研究了不同工艺过程对玻璃性能的影响. 分析了样品ICP的成分，扫描电镜，X-射线衍射谱， 差热分析和紫外-可见-近红外透过光谱测试. 结果表明：使用刚玉坩埚能提高玻璃的抗析晶稳定性 和透过率，陶瓷坩埚和白金坩埚均受到严重腐蚀，玻璃组分也随之发生很大变化. 当熔制温度从1 100 ℃变化到1 300 ℃时，玻璃的颜色从浅黄色变到深红棕色. 尤其是白金粒子被腐蚀进入玻璃液 后，玻璃中很容易形成纳米颗粒或者团聚形成胶体粒子，在玻璃中形成色散源，加深玻璃的颜色， 降低透过率. 1 300 ℃下，白金粒子起到晶核剂的作用，生成Bi2Pt2O7和BiB3O6晶相，导致玻璃失透.

Effects of annealing on the color, absorption spectra, and light yield of Ce : YAlO3 single crystal grown by the temperature gradient technique

YAlO3 single crystal doped with Ce3+ at concentration 1% was grown by the temperature gradient technique. The as-grown crystal was pink. After H-2 annealing or air annealing at 1400degreesC for 20 h, the crystal was turned into colorless. We concluded there were two kinds of color centers in the as-grown crystal. One is F+ center attributed to absorption band peaking at about 530 nm, the other is O- center attributed to absorption band peaking at about 390 nm. This color centers model can be applied in explaining the experiment phenomena including the color changes, the absorption spectra changes, and the light yield changes of Ce:YAP crystals before and after annealing. (C) 2004 American Institute of Physics.

Thermal stability and crystallochemical analysis for CoII based coordination polymers with TPP and TPPS porphyrins

Artículo CrystEngComm 2013

Study on the hydrolytic property and thermal stability of LiAlO2 substrate

The hydrolytic property and thermal stability of LiAlO2 (LAO), important factors for its application, were examined by AFM and X-ray rocking curve. We found that H2O may be deleterious for LAO surface polishing when the root mean square (RMS) value is less than 1 nm. However, when the RMS value is more than 1 nm it may be useful for LAO polishing. (100)-plane LAO substrates are annealed in the range of 850-900 degrees C in flux N-2, Slick AlN layer probably is produced on the substrate surface. M-plane GaN layer has grown on the substrate by metal-organic chemical vapor deposition (MOCVD) method. Theses results show that LiAlO2 crystal is a promising substrate of fabricating high-efficiency LEDs by MOCVD. (c) 2006 Elsevier B.V. All rights reserved.

Hyers-Ulam-Rassias Stability of Functional Differential Systems with Point and Distributed Delays

This paper investigates stability and asymptotic properties of the error with respect to its nominal version of a nonlinear time-varying perturbed functional differential system subject to point, finite-distributed, and Volterra-type distributed delays associated with linear dynamics together with a class of nonlinear delayed dynamics. The boundedness of the error and its asymptotic convergence to zero are investigated with the results being obtained based on the Hyers-Ulam-Rassias analysis.

Phi 140 mm sapphire crystal growth by temperature gradient techniques and its color centers

Sapphire crystals, 140 mm in diameter and 90 turn in height, have been grown by temperature gradient techniques (TGT). The growth direction of the boule was fixed by means of Lane X-ray diffraction. A prominent 204 nm absorption band in TGT-Al2O3. which does not appear in single crystals grown by Czochralski method has been studied. Analysis further substantiates the F-center model of this band. Two relatively weaker bands absorbing at 232 nm and 254 nm were ascribed to F+ centers. F-type centers concentration was determined using Smakula's equation. (c) 2005 Elsevier B.V. All rights reserved.

Color centers and charge state change in Ce : YAG crystals grown by temperature gradient techniques

Color centers and impurity defects of Ce:YAG crystals grown in reduction atmosphere by temperature gradient techniques have been investigated by means of gamma irradiation and thermal treatments. Four absorption bands associated with color centers or impurity defects at 235, 255, 294 and 370 nm were observed in as-grown crystals. Changes in optical intensity of the 235 and 370 nm bands after gamma irradiation indicate that they are associated with F+-type color center. Charge state change processes of Fe3+ impurity and Ce3+ ions take place in the irradiation process. The variations of Ce3+ ions concentration clearly indicate that Ce4+ ions exist in Ce:YAG crystals and gamma irradiations could increase the concentration of Ce3+ ions. Annealing treatments and the changes in optical density suggest that a heterovalent impurity ion associated with the 294 nm band seems to be present in the crystals. (c) 2005 Elsevier B.V. All rights reserved.

Color centers and charge state recharge in gamma-irradiated Yb : YAP

Gamma-ray irradiation induced color centers and charge state recharge of impurity and doped ion in 10 at.% Yb:YAP have been studied. The change in the additional absorption (AA) spectra is mainly related to the charge exchange of the impurity Fe2+, Fe3+ and Yb3+ ions. Two impurity color center bands at 255 and 313 nm were attributed to Fe3+ and Fe2+ ions, respectively. The broad AA band centered at 385 nm may be associated with the cation vacancies and F-type center. The transition Yb3+ -> Yb2+ takes place in the process of gamma-irradiation. Oxygen annealing and gamma-ray irradiation lead to an opposite effect on the absorption properties of the Yb:YAP crystal. In the air annealing process, the transition Fe2+ -> Fe3+ and Yb2+ -> Yb3+ take place and the color centers responsible for the 385 nm band was destroyed. (c) 2005 Elsevier B.V. All rights reserved.

Color centers in Yb : YAG crystals grown by temperature-gradient techniques

Yb: YAG (Yb: Y3Al5O12) crystals have been grown by temperature-gradient techniques (TGT) and their color centers and impurity defects were investigated by means of gamma irradiations and thermal treatment. Two color centers located at 255 and 290 nm were observed in the as-grown TGT-Yb: YAG. Analysis shows that the 255 nm band may be associated with Fe3+ ions. Absorption intensity changes of the 290 nm band after gamma irradiation and thermal treatment indicate that this band may be associated with oxygen-vacancy defects. (c) 2006 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Emprego dos processos de eletrofloculação e osmose inversa no tratamento de águas oleosas

A descarga desenfreada de águas residuais no meio ambiente, ao longo dos últimos anos, vem acelerando o processo de contaminação e degradação dos corpos hídricos no mundo. Tais rejeitos apresentam elevada carga de contaminantes e de concentração de matéria orgânica o que leva a mortandade das espécies pela concorrência ao oxigênio e, em casos extremos, a aceleração dos processos de eutrofização. Pensando nisso, o presente trabalho estudou um sistema híbrido, em batelada, de tratamento de águas oleosas simuladas em laboratório pela adição de um determinado óleo lubrificante em uma solução aquosa de agentes emulsificantes e eletrólito suporte. O sistema de tratamento foi composto de duas etapas, onde na primeira avaliou-se o uso da técnica da eletrofloculação, responsável por quebrar a estabilidade das emulsões óleo/água e de uma segunda que avaliou o uso de processos de separação com membranas visando à remoção do metal adicionado ao efluente na etapa anterior. O sistema de eletrofloculação foi avaliado em relação ao uso de eletrodos de alumínio e ferro com correntes elétricas de 1A, 2A e 3A, nos modos contínuo e alternado. Os resultados apontaram um maior consumo evidente de massa de eletrodos quando do uso da corrente contínua, 4,0337g 0,0132 para o alumínio e 3,8260g 0,0181 para o ferro ao passo que o consumo foi de 2,1400g 0,0099 para o alumínio e 2,4121g 0,0127 para o ferro quando do o uso da corrente alternada. Foram alcançadas remoções máximas de 98 % 0 da DQO, 99,77 % 0,27 de remoção da cor e 100 % 0 de remoção da turbidez para o uso de corrente alternada e eletrodos de alumínio enquanto se alcançaram remoções máximas 96 % 1 da DQO, 99,46 % 0,82 de remoção da cor e também 100 % 0 de remoção da turbidez no uso de eletrodos de ferro. Na segunda etapa do estudo, a osmose inversa, o sistema utilizado atingiu rejeições de 99,53 % 0,12; 99,56 % 0,13 e de 98,87 % 0,36, para pressões respectivas de 10, 20 e 30 bar. Além disso, foram obtidos fluxos crescentes de permeado 10,87 L/h.m2 0,25; 15,67 L/h.m2 0,53; 18,49 L/h.m2 0,74 com o também aumento da pressão. Ao final do estudo alcançou-se um efluente final com baixa carga orgânica e de metais, estando o mesmo apto ao lançamento nos corpos receptores. Entretanto, mecanismos de controle, sobretudo de pH devem ser incluídos no projeto desses sistemas uma vez que esse parâmetro sofre alterações ao longo do processo