Characterization of Tollip in the Interleulkin-1 Receptor/Toll Like Receptors signaling pathways

SUMMARY IL-1R and TLRs are key players in innate immunity and inflammation. Tollip was identified as a component of IL-1RI, TLR2 and TLR4 signaling complexes that activate NF-κB and MAP kinase pathways. Tollip was previously shown as a negative regulator of NF-κB and MAP Kinase activation. We have characterized the role of Tollip in IL-R/TLRs induced signaling by the analysis of the Tollip deficient mice. We showed that NF-κB and MAPK (p38, JNK, or ERK1/2) signaling appeared normal in Tollip deficient cells following stimulation with IL-1β, lipopolysaccharide (LPS), and other TLR ligands. Also IL-1β and TLRs ligands induced activation of immune cells was indistinguishable from wild-type cells. Strikingly, in Tollip deficient mice the production of the inflammatory cytokines, IL-6 or TNF-α was significantly reduced relative to control mice after treatment with physiological doses of IL-1β or LPS, whereas no difference was observed at high doses of stimulation with LPS or in LPS induced septic shock. Therefore, Tollip could be critical for regulation of optimal responses to IL-1β and LPS, in addition to its role as negative regulator of the signaling. We also studied the role of Tollip as an endocytic adaptor for IL-1R endocytosis. We could show that Il-1R is ubiquitinated after IL-1β stimulation, and that Tollip's CUE domain binds IL-1RI in an ubiquitin-dependent manner. We followed IL-1R internalization and Tollip localization by confocal microscopy. Consistent with a role for Tollip in sorting of ubiquitinated IL-1RI, a significant amount of Tollip was also localized at the late endosomal compartment. We could show that Tollip is required for efficient lysosomal targeting of ubiquitinated IL-1R1, In the absence of Tollip or in Tollip deficient cells reconstituted with a Tollip mutant (defective in ubiquitin binding) IL-1RI accumulates in enlarged late endosomes. In addition, Tollip was shown to interact with, another endocytic adapter, Toml, and both interact with IL-1RI. In conclusion, we showed that Tollip is required for IL-1β and LPS signaling for cytokine production. In addition we showed and that Tollip has a role as an endocytic adapter, necessary for efficient trafficking and lysosomal degradation of IL-1RI. Resumé Le récepteur à l'interleukine-1 (IL-1R) et les récepteurs "Toll-like" (TLRs) sont des acteurs cruciaux de la réponse immunitaire innée et de l'inflammation. La proteine Tollip a été identifiée comme étant un élément des complexes de signalisation, induits par les récepteurs IL-1RI, TLR-2 et TLR-4, qui mènent à l'activation de la voie des MAP kinases et de NF-κB. Dans de précédentes études, il a été montré que Tollip pouvait inhiber ces deux voies de signalisation. Nous avons voulu caractériser plus précisément le rôle de Tollip dans l'activation des voies de signalisation mitées par IL-1R/TLRs en utilisant une lignée murine déficiente pour la protéine Tollip. Ainsi, en absence de Tollip, les cascades d'activation de NF-κB et MAPK (p38, JNK, or ERK1/2) ne semblent pas affectées après stimulation avec IL-1β, lipopolysaccharide (LPS) ou d' autres ligands des TLR. La réponse des cellules du système immunitaire induite par la stimulation avec IL-1β et les ligands des TLR est également comparable entre les souris sauvages et les souris deficientes pour Tollip. Par contre, dans cette lignée murine, la production de cytokines proinflammatoires IL-6 et TNFα induite par la stimulation à dose physiologique de IL-1β or LPS, est réduite. Cependant, lors de stimulation à plus hautes doses de LPS ou pendant un choc septique induit par de LPS, cette réduction n'est pas observée. Ces résultats montrent que Tollip pourrait avoir un rôle déterminant dans l'activation optimale en réponse à l' IL-1β et au LPS qui s'ajoute à sa fonction inhibitrice des mêmes voies de signalisation. Nous avons aussi étudié le rôle de Tollip comme molécule adaptatatrice du mécanisme endocytique d'internalisation de l' IL-1RI. Ainsi, l' IL-1R est ubiquitiné après stimulation par l' IL-1β , permettant à Tollip de se lier au récepteur. Cette interaction est réalisée entre le domaine CUE de Tollip et l'IL-1R via l'ubiquitine. L'internalisation et la localisation intracellulaire de l'IL-1RI et de Tollip ont été observés par microscopie confocale. En accord avec le rôle de Tollip dans le triage et la recirculation des IL-1R ubiquitiné, une quantité importante de Tollip été détectée dans l' endosome tardif. Nous avons pu démontrer que Tollip était nécessaire pour diriger efficacement ubiquitiné vers les lysosomes. Dans des cellules déficientes pour Tollip, ou reconstituées avec un mutant de Tollip (MF/AA) incapable de lier l'ubiquitine, IL-1RI s'accumule dans des vesicules anormales de l'endosome tardif. Dans ce travail, nous avons pu confirmer et préciser la fonction de la protéine Tollip dans l' activation de la production de cytokines induites par l' IL-1p and le LPS lors de l'inflammation et découvrir son rôle d'adaptateur dans l' internalisation et l'endocytose de l' IL-1RI.

Glutathione deficit in schizophrenia: strategies to increase glutathione levels in " in vitro " and clinical studies

Summary: Decrease in glutathione (GSH) levels was observed in cerebrospinal fluid, prefrontal cortex and post-mortem striatum of schizophrenia patients. Evidences suggest a defect in GSH synthesis at the levels of the rate-limiting synthesizing enzyme, glutamate cysteine ligase (GCL). Indeed, polymorphisms in the gene of the modifier subunit of GCL (GCLM) was shown to be associated with the disease in three different populations, GCLM gene expression is decreaséd in fibroblasts from patients and the increase in GCL activity induced by an oxidative stress is lower in patients' fibroblasts compared to controls. GSH being a major antioxydant and redox regulator, its presence is of high importance for protecting cells against oxidative stress. The aim of the present work was to use various substances to increase GSH levels by diverse strategies. Since the synthesizing enzyme GCL is defective, bypassing this enzyme was the first strategy we used. GSH ethyl ester (GSHEE), a membrane permeable analog of GSH, succeeded in replenishing GSH levels in cultured neurons and astrocytes previously depleted in GSH by L-buthionine-(S,R)-sulfoximine (BSO), an inhibitor of GCL. GSHEE also abolished dopamine-induced decrease of NMDA-mediated calcium response observed in BSO-treated neurons. y-Glutamylcysteine ethyl ester (GCSE), a membrane permeable analog of the product of GCL, increased GSH levels only in astrocytes. The second strategy was to boost the defective enzyme GCL. While quercetin (flavonoid) could increase GSH levels only in astrocytes, curcumin (polyphenol) and tertbutylhydroquinone (quinone) were successful in both neurons and astrocytes, via an increase in the gene expression of the two subunits of GCL and, consequently, an increase in the activity of the enzyme. However, FK506, an immunosupressant, was unefficient. Treating astrocytes from GCLM KO mice showed that the modulatory subunit is necessary for the action of the substances. Finally, since cysteine is the limiting precursor in the synthesis of GSH, we hypothesized that we could increase GSH levels by providing more of this precursor. N-acetyl-cysteine (NAC), a cysteine donor, was administered to schizophrenia patients, using adouble-blind and cross-over protocol. NAC significantly improved the mismatch negativity (MMN), a component of the auditory evoked potentials, thought to reflect selective current flowing through open, unblocked NMDA channels. Considering that NMDA function is reduced when GSH levels are low, increasing these levels with NAC could improve NMDA function as reflected by the improvement in the generation of the MMN. Résumé: Les taux de glutathion (GSH) dans le liquide céphalo-rachidien, le cortex préfrontal ainsi que le striatum post-mortem de patients schizophrènes, sont diminués. L'enzyme limitante dans la synthèse du GSH, la glutamyl-cysteine ligase (GCL), est défectueuse. En effet, des polymorphismes dans le gène de la sous-unité modulatrice de GCL (GCLM) sont associés à la maladie, l'expression du gène GCLM est diminuée dans les fibroblastes de patients et, lors d'un stress oxidative, l'augmentation de l'activité de GCL est plus faible chez les patients que chez les contrôles. Le GSH étant un important antioxydant et régulateur du status redox, sa présence est primordiale afin de protéger les cellules contre les stress oxydatifs. Au cours du présent travail, une variété de substances ont été utilisées dans le but d'augmenter les taux de GSH. Passer outre l'enzyme de synthèse GCL qui est défectueuse fut la première stratégie utilisée. L'éthylester de GSH (GSHEE), un analogue du GSH qui pénètre la membrane cellulaire, a augmenté les taux de GSH dans des neurones et des astrocytes déficitaires en GSH dû au L-buthionine-(S,R)-sulfoximine (BSO), un inhibiteur du GCL. Dans ces neurones, le GSHEE a aussi aboli la diminution de la réponse NMDA, induite parla dopamine. L'éthyl-ester de y-glutamylcysteine (GCEE), un analogue du produit de la GCL qui pénètre la membrane cellulaire, a augmenté les taux de GSH seulement dans les astrocytes. La seconde stratégie était d'augmenter l'activité de l'enzyme GCL. Tandis que la quercétine (flavonoïde) n'a pu augmenter les taux de GSH que dans les astrocytes, la curcumin (polyphénol) et le tert-butylhydroquinone (quinone) furent efficaces dans les deux types de cellules, via une augmentation de l'expression des gènes des deux sous-unités de GCL et de l'activité de l'enzyme. Le FK506 (immunosupresseur) n' a démontré aucune efficacité. Traiter des astrocytes provenant de souris GCLM KO a permis d'observer que la sous-unité modulatoire est nécessaire à l'action des substances. Enfin, puisque la cysteine est le substrat limitant dans la synthèse du GSH, fournir plus de ce présurseur pourrait augmenter les taux de GSH. Nacétyl-cystéine (NAC), un donneur de cystéine, a été administrée à des schizophrènes, lors d'une étude en double-aveugle et cross-over. NAC a amélioré le mismatch negativity (MMN), un composant des potentials évoqués auditifs, qui reflète le courant circulant via les canaux NMDA. Puisque la fonctionnalité des R-NMDA est diminuée lorsque les taux de GSH sont bas, augmenter ces taux avec NAC pourrait améliorer la fonction des R-NMDA, réflété par une augmentation de l'amplitude du MMN.

FPGA-Based Control Design for Power Electronic Applications

Tehoelektoniikkalaitteella tarkoitetaan ohjaus- ja säätöjärjestelmää, jolla sähköä muokataan saatavilla olevasta muodosta haluttuun uuteen muotoon ja samalla hallitaan sähköisen tehon virtausta lähteestä käyttökohteeseen. Tämä siis eroaa signaalielektroniikasta, jossa sähköllä tyypillisesti siirretään tietoa hyödyntäen eri tiloja. Tehoelektroniikkalaitteita vertailtaessa katsotaan yleensä niiden luotettavuutta, kokoa, tehokkuutta, säätötarkkuutta ja tietysti hintaa. Tyypillisiä tehoelektroniikkalaitteita ovat taajuudenmuuttajat, UPS (Uninterruptible Power Supply) -laitteet, hitsauskoneet, induktiokuumentimet sekä erilaiset teholähteet. Perinteisesti näiden laitteiden ohjaus toteutetaan käyttäen mikroprosessoreja, ASIC- (Application Specific Integrated Circuit) tai IC (Intergrated Circuit) -piirejä sekä analogisia säätimiä. Tässä tutkimuksessa on analysoitu FPGA (Field Programmable Gate Array) -piirien soveltuvuutta tehoelektroniikan ohjaukseen. FPGA-piirien rakenne muodostuu erilaisista loogisista elementeistä ja niiden välisistä yhdysjohdoista.Loogiset elementit ovat porttipiirejä ja kiikkuja. Yhdysjohdot ja loogiset elementit ovat piirissä kiinteitä eikä koostumusta tai lukumäärää voi jälkikäteen muuttaa. Ohjelmoitavuus syntyy elementtien välisistä liitännöistä. Piirissä on lukuisia, jopa miljoonia kytkimiä, joiden asento voidaan asettaa. Siten piirin peruselementeistä voidaan muodostaa lukematon määrä erilaisia toiminnallisia kokonaisuuksia. FPGA-piirejä on pitkään käytetty kommunikointialan tuotteissa ja siksi niiden kehitys on viime vuosina ollut nopeaa. Samalla hinnat ovat pudonneet. Tästä johtuen FPGA-piiristä on tullut kiinnostava vaihtoehto myös tehoelektroniikkalaitteiden ohjaukseen. Väitöstyössä FPGA-piirien käytön soveltuvuutta on tutkittu käyttäen kahta vaativaa ja erilaista käytännön tehoelektroniikkalaitetta: taajuudenmuuttajaa ja hitsauskonetta. Molempiin testikohteisiin rakennettiin alan suomalaisten teollisuusyritysten kanssa soveltuvat prototyypit,joiden ohjauselektroniikka muutettiin FPGA-pohjaiseksi. Lisäksi kehitettiin tätä uutta tekniikkaa hyödyntävät uudentyyppiset ohjausmenetelmät. Prototyyppien toimivuutta verrattiin vastaaviin perinteisillä menetelmillä ohjattuihin kaupallisiin tuotteisiin ja havaittiin FPGA-piirien mahdollistaman rinnakkaisen laskennantuomat edut molempien tehoelektroniikkalaitteiden toimivuudessa. Työssä on myösesitetty uusia menetelmiä ja työkaluja FPGA-pohjaisen säätöjärjestelmän kehitykseen ja testaukseen. Esitetyillä menetelmillä tuotteiden kehitys saadaan mahdollisimman nopeaksi ja tehokkaaksi. Lisäksi työssä on kehitetty FPGA:n sisäinen ohjaus- ja kommunikointiväylärakenne, joka palvelee tehoelektroniikkalaitteiden ohjaussovelluksia. Uusi kommunikointirakenne edistää lisäksi jo tehtyjen osajärjestelmien uudelleen käytettävyyttä tulevissa sovelluksissa ja tuotesukupolvissa.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

The transcriptional network activated by Cln3 cyclin at the G1-to-S transition of the yeast cell cycle

Background: The G1-to-S transition of the cell cycle in the yeast Saccharomyces cerevisiae involves an extensive transcriptional program driven by transcription factors SBF (Swi4-Swi6) and MBF (Mbp1-Swi6). Activation of these factors ultimately depends on the G1 cyclin Cln3. Results: To determine the transcriptional targets of Cln3 and their dependence on SBF or MBF, we first have used DNA microarrays to interrogate gene expression upon Cln3 overexpression in synchronized cultures of strains lacking components of SBF and/or MBF. Secondly, we have integrated this expression dataset together with other heterogeneous data sources into a single probabilistic model based on Bayesian statistics. Our analysis has produced more than 200 transcription factor-target assignments, validated by ChIP assays and by functional enrichment. Our predictions show higher internal coherence and predictive power than previous classifications. Our results support a model whereby SBF and MBF may be differentially activated by Cln3. Conclusions: Integration of heterogeneous genome-wide datasets is key to building accurate transcriptional networks. By such integration, we provide here a reliable transcriptional network at the G1-to-S transition in the budding yeast cell cycle. Our results suggest that to improve the reliability of predictions we need to feed our models with more informative experimental data.

Genome-wide transcriptional responses to shade: Linking shade avoidance and auxin

Plants have the ability to use the composition of incident light as a cue to adapt development and growth to their environment. Arabidopsis thaliana as well as many crops are best adapted to sunny habitats. When subjected to shade, these plants exhibit a variety of physiological responses collectively called shade avoidance syndrome (SAS). It includes increased growth of hypocotyl and petioles, decreased growth rate of cotyledons and reduced branching and crop yield. These responses are mainly mediated by phytochrome photoreceptors, which exist either in an active, far-red light (FR) absorbing or an inactive, red light (R) absorbing isoform. In direct sunlight, the R to FR light (R/FR) ratio is high and converts the phytochromes into their physiologically active state. The phytochromes interact with downstream transcription factors such as PHYTOCHROME INTERACTING FACTOR (PIF), which are subsequently degraded. Light filtered through a canopy is strongly depleted in R, which result in a low R/FR ratio and renders the phytochromes inactive. Protein levels of downstream transcription factors are stabilized, which initiates the expression of shade-induced genes such as HFR1, PIL1 or ATHB-2. In my thesis, I investigated transcriptional responses mediated by the SAS in whole Arabidopsis seedlings. Using microarray and chromatin immunoprecipitation data, we identified genome-wide PIF4 and PIF5 dependent shade regulated gene as well as putative direct target genes of PIF5. This revealed evidence for a direct regulatory link between phytochrome signaling and the growth promoting phytohormone auxin (IAA) at the level of biosynthesis, transport and signaling. Subsequently, it was shown, that free-IAA levels are upregulated in response to shade. It is assumed that shade-induced auxin production takes predominantly place in cotyledons of seedlings. This implies, that IAA is subsequently transported basipetally to the hypocotyl and enhances elongation growth. The importance of auxin transport for growth responses has been established by chemical and genetic approaches. To gain a better understanding of spatio-temporal transcriptional regulation of shade-induce auxin, I generated in a second project, an organ specific high throughput data focusing on cotyledon and hypocotyl of young Arabidopsis seedlings. Interestingly, both organs show an opposite growth regulation by shade. I first investigated the spatio-transcriptional regulation of auxin re- sponsive gene, in order to determine how broad gene expression pattern can be explained by the hypothesized movement of auxin from cotyledons to hypocotyls in shade. The analysis suggests, that several genes are indeed regulated according to our prediction and others are regulated in a more complex manner. In addition, analysis of gene families of auxin biosynthetic and transport components, lead to the identification of essential family members for shade-induced growth re- sponses, which were subsequently experimentally confirmed. Finally, the analysis of expression pattern identified several candidate genes, which possibly explain aspects of the opposite growth response of the different organs.

The Smc5/6 complex is required for dissolution of DNA-mediated sister chromatid linkages

Mitotic chromosome segregation requires the removal of physical connections between sister chromatids. In addition to cohesin and topological entrapments, sister chromatid separation can be prevented by the presence of chromosome junctions or ongoing DNA replication. We will collectively refer to them as DNA-mediated linkages. Although this type of structures has been documented in different DNA replication and repair mutants, there is no known essential mechanism ensuring their timely removal before mitosis. Here, we show that the dissolution of these connections is an active process that requires the Smc5/6 complex, together with Mms21, its associated SUMO-ligase. Failure to remove DNA-mediated linkages causes gross chromosome missegregation in anaphase. Moreover, we show that Smc5/6 is capable to dissolve them in metaphase-arrested cells, thus restoring chromosome resolution and segregation. We propose that Smc5/6 has an essential role in the removal of DNA-mediated linkages to prevent chromosome missegregation and aneuploidy.

Design and implementation of FPGA-based LQ control of active magnetic bearings

The need for high performance, high precision, and energy saving in rotating machinery demands an alternative solution to traditional bearings. Because of the contactless operation principle, the rotating machines employing active magnetic bearings (AMBs) provide many advantages over the traditional ones. The advantages such as contamination-free operation, low maintenance costs, high rotational speeds, low parasitic losses, programmable stiffness and damping, and vibration insulation come at expense of high cost, and complex technical solution. All these properties make the use of AMBs appropriate primarily for specific and highly demanding applications. High performance and high precision control requires model-based control methods and accurate models of the flexible rotor. In turn, complex models lead to high-order controllers and feature considerable computational burden. Fortunately, in the last few years the advancements in signal processing devices provide new perspective on the real-time control of AMBs. The design and the real-time digital implementation of the high-order LQ controllers, which focus on fast execution times, are the subjects of this work. In particular, the control design and implementation in the field programmable gate array (FPGA) circuits are investigated. The optimal design is guided by the physical constraints of the system for selecting the optimal weighting matrices. The plant model is complemented by augmenting appropriate disturbance models. The compensation of the force-field nonlinearities is proposed for decreasing the uncertainty of the actuator. A disturbance-observer-based unbalance compensation for canceling the magnetic force vibrations or vibrations in the measured positions is presented. The theoretical studies are verified by the practical experiments utilizing a custom-built laboratory test rig. The test rig uses a prototyping control platform developed in the scope of this work. To sum up, the work makes a step in the direction of an embedded single-chip FPGA-based controller of AMBs.

Diffraction grating couplers milled in Si3N4 rib waveguides with a focused ion beam

Focused ion beam milling is a processing technology which allows flexible direct writing of nanometer scale features efficiently substituting electron beam lithography. No mask need results in ability for patterns writing even on fragile micromechanical devices. In this work we studied the abilities of the tool for fabrication of diffraction grating couplers in silicon nitride waveguides. The gratings were fabricated on a chip with extra fragile cantilevers of sub micron thickness. Optical characterization of the couplers was done using excitation of the waveguides in visible range by focused Gaussian beams of different waist sizes. Influence of Ga+ implantation on the device performance was studied.

Genome-wide chromatin occupancy reveals a role for ASH2 in transcriptional pausing

While it is widely acknowledged that the ubiquitin-proteasome system plays an important role in transcription, little is known concerning the mechanistic basis, in particular the spatial organization of proteasome-dependent proteolysis at the transcription site. Here, we show that proteasomal activity and tetraubiquitinated proteins concentrate to nucleoplasmic microenvironments in the euchromatin. Such proteolytic domains are immobile and distinctly positioned in relation to transcriptional processes. Analysis of gene arrays and early genes in Caenorhabditis elegans embryos reveals that proteasomes and proteasomal activity are distantly located relative to transcriptionally active genes. In contrast, transcriptional inhibition generally induces local overlap of proteolytic microdomains with components of the transcription machinery and degradation of RNA polymerase II. The results establish that spatial organization of proteasomal activity differs with respect to distinct phases of the transcription cycle in at least some genes, and thus might contribute to the plasticity of gene expression in response to environmental stimuli.

Kaukolämmöntuotannon ja verkon käytön optimointi uudessa ajotilanteessa

Diplomityössä kehitetään Savonlinnan kaupungin kaukolämmöntuotantoa ja kaukolämpöverkon käyttöä muuttuneessa ajotilanteessa. Muuttunut tilanne syntyy, kun Savonlinnaan rakennetaan uusi lämmitysvoimalaitos. Kaukolämpöverkkoa yhdistetään samanaikaisesti viidestä erillisestä verkosta yhdeksi kokonaiseksi verkoksi. Kaukolämmöntuotannon ja verkon käytön optimointi suoritettiin Process Vision Oy: n kehittämällä kaukolämpöverkon laskentaohjelmalla. Optimoinnissa pyrittiin saamaan mahdollisimman aikaisin taloudellisin laitos eli uusi hakelaitos täyteen tehoon ja tarvittava lisäteho otettiin öljylämpökeskuksista. Hakelaitoksen käytettävyyttä lisättiin rakentamalla kaukolämpöverkkoon välipumppaamo ja kaukolämpöveden apujäähdytin. Hakelaitosta voidaan käyttää 0°C ulkolämpötilaan asti, mutta kun käytetään apuna välipumppausta voidaan pumppauksellisesti pelkästään hakelaitokselta syöttää tehoa aina 14 °C lämpötilaan asti. Välipumppauksen avulla vuosittain vähennetään öljyn ja lisätään hakkeen polttoa n. 10,4 GWh. Nykyisillä öljyn ja hakkeen hinnoilla säästö vuodessa on n. 887000 mk. Välipumppauksella vähennetään lisäksi kaukolämpöverkon pumppauskustannuksia.

Keraamisten teräpalojen käyttö niukkaseosteisten terästen lastuamiseen normaaleissa toimitustiloissa

Tämän tutkimuksen tavoitteena oli tutkia keraamisten kääntöterien soveltuvuus niukkaseosteräksille ja M-käsittelyn vaikutus teränkestoaikoihin. Lisäksi tavoitteena oli tutkia keraamiseosten erityisominaisuudet ja muodostaa käsitys keraamisilla kääntöterillä sorvaamisen erityisvaatimuksista. Kirjallisuusosassa selvitettiin tutkimushetkellä saatavissa olleet keraamiset teräaineseokset ja niiden ominaisuudet sekä selvitettiin keraamisten kääntöterien viimeaikaiset kehitystrendit. Lastuamistutkimus toteutettiin standardin ISO 3685:1993 mukaisesti, minkä lisäksi mitattiin lastuamisvoimat ja tehtiin kokeessa käytetyille terille lastunmurtokoe. Koemateriaalit olivat Imatra Steelin GreenCut, Hydax 25, M-käsittelemätön 42CrMo4 ja M-käsitelty MoC410M. Kokeissa käytetyt kääntöterät olivat eri valmistajien alumiinioksiditeriä, titaanikarbidiseostettuja alumiinioksiditeriä, kuituvahvisteisia ja yksi puhdas titaanikarbidiseosteinen terä. Koetulosten perusteella hyvän teränkestoajan saavuttamiseksi on tärkeää valita oikea keraamiseos ja sille soveltuvat parametrit. Oikein valituilla parametreilla M-terästä sorvattaessa tulokset ylittävät kovametalleilla saavutettavissa olevat arvot. Tulosten perusteella niukkaseostettujen terästen sorvaus onnistuu hyvin keraamisilla kääntöterillä, mutta kovametallisorvaukseen verrattuna syöttöä on laskettava ja lastuamisnopeutta lisättävä. Tämän työn tuloksia voidaan soveltaa sopivissa olosuhteissa toteutettavassa kappaletavaratuotannossa. Sovelluksen onnistuminen vaatii tukevat työstöolosuhteet ja riittävien lastuamisnopeuksien saavuttamisen.

Multilayer switch hardware support for Linux

VDSL on teknologia, joka mahdollistaa nopeat Internet-yhteydet tavallista puhelinlinjaa käyttäen. Tätä varten käyttäjä tarvitsee VDSL-modeemin ja Internet-operaattori reitittimen, johon VDSL-linjat kytketään. Reitittimen on oltava suorituskykyinen, jotta kaikki VDSL-liikenne voidaan reittittää eteenpäin. Tehokkuutta haetaan tekemällä suuri osa reitityksestä erityisillä reititinpiireillä. Tässä diplomityössä käsitellään reititinpiirien teoriaa ja niiden hallintaa. Lisäksi vertailtiin kolmen suuren valmistajan tuotteita. Tuotteiden tarjoamat ominaisuudet vaikuttivat hyvin yhteneväisiltä. Ominaisuuksien hallinta ja toteutus olivat erilaisia. Työn tavoitteena oli löytää ohjelmistoarkkitehtuuri piirien ohjaamiseen niin, että Linux-käyttöjärjestelmän ytimen palveluja voitaisiin käyttää mahdollisimman hyödyllisesti. Työssä havaittiin, että ohjelmistoarkkitehtuurin voi määritellä monella eri tavalla riippuen siitä, miten piiri on kytketty prosessoriin, mitä piirin ominaisuuksia halutaan käyttää ja miten arkkitehtuuria halutaan jatkossa laajentaa.

Parkinson"s disease DJ-1 L166P alters rRNA biogenesis by exclusion of TTRAP from the nucleolus and sequestration into cytoplasmic aggregates via TRAF6

Mutations in PARK7/DJ-1 gene are associated to autosomal recessive early onset forms of Parkinson"s disease (PD). Although large gene deletions have been linked to a loss-of-function phenotype, the pathogenic mechanism of missense mutations is less clear. The L166P mutation causes misfolding of DJ-1 protein and its degradation. L166P protein may also accumulate into insoluble cytoplasmic aggregates with a mechanism facilitated by the E3 ligase TNF receptor associated factor 6 (TRAF6). Upon proteasome impairment L166P activates the JNK/p38 MAPK apoptotic pathway by its interaction with TRAF and TNF Receptor Associated Protein (TTRAP). When proteasome activity is blocked in the presence of wild-type DJ-1, TTRAP forms aggregates that are localized to the cytoplasm or associated to nucleolar cavities, where it is required for a correct rRNA biogenesis. In this study we show that in post-mortem brains of sporadic PD patients TTRAP is associated to the nucleolus and to Lewy Bodies, cytoplasmic aggregates considered the hallmark of the disease. In SH-SY5Y neuroblastoma cells, misfolded mutant DJ-1 L166P alters rRNA biogenesis inhibiting TTRAP localization to the nucleolus and enhancing its recruitment into cytoplasmic aggregates with a mechanism that depends in part on TRAF6 activity. This work suggests that TTRAP plays a role in the molecular mechanisms of both sporadic and familial PD. Furthermore, it unveils the existence of an interplay between cytoplasmic and nucleolar aggregates that impacts rRNA biogenesis and involves TRAF6

IRTOPALATERÄN KEHITTÄMINEN SÄRMÄ- JA PROFILOINTIHAKETUKSEEN

Diplomityön tarkoituksena on kehittää irtopalaterä sahahakkeen valmistukseen. Tutkimuksessa perehdytään lastun irtoamisen perusteisiin ja lastun kulkeutumiseen ulos terältä. Tutkimuksessa keskeisenä osana ovat laboratoriokokeet joissa suurnopeuskameralla kuvaamalla selvitetään lastun kulkeutuminen. Saatujen tulosten perusteella muodostetaan terän toimivuuden kannalta keskeiset suunnitteluperusteet. Tutkimuksen kirjallisessa osuudessa selvitetään lastun muodostuminen ja siihen vaikuttavat tekijät.