Analise técnico-econômica de um gaseificador Downdraft e de filtros para limpeza de gás de síntese

The biomass gasification systems have been used for a long time and prove to be a good alternative to the generation of energy problems. This type of management requires a simple installation and maintenance which gives them a high availability. In Biomass project via Call CTEnerg 33/2006-1, funded by the Ministry of Science and Technology - MCT - Brazil, the Group Energy Systems Optimization – GOSE - at FEG - UNESP built and tested two prototypes of gasifiers. These is fed with 25 kg / h of dry wood (chips), and 50 Nm3 / h of air to produce gas at a flow rate of approximately 70 Nm3 / h of wood (syngas) at a temperature approximately 600 ° C. In this work of graduation, studies were conducted on the materials used in both the gasifier as well as cleaning the filter synthesis gases. The system of gas cleaning and conditioning is vital to ensure the life of the Internal Combustion Engine. In this case the studies of different filters for small gasification systems (properties, materials used, characteristics, types, etc.) are very relevant to its use in the prototype of the college campus. Were also performed a technical and economic analysis of a cogeneration system that consists in the combination of the downdraft gasifier studied in this work, an internal combustion engine, two heat exchangers and a SRA (absorption system refrigerator). Were calculated the costs of electricity generation, hot water and cold water. Finally, we analyzed the economic feasibility of the project

Dimensionamento de trocadores de calor aplicados à refrigeração da água do molde de um processo de lingotamento contínuo

This study aims to determine the most suitable type of heat exchanger to be applied to the water cooling the mold of a continuous casting process. Basically been studied four types of heat exchangers: shell and tube operating in counterflow, shell and tube operating in parallel flow, plate type and operating counterflow and plates operating in parallel flow. Initially is displayed design of heat exchangers for the conditions of the proposed application. With the heat exchangers dimensioned comparisons were made in order to set the heat exchanger more suitable for application. In the study, one comes to the conclusion that the plate type heat exchangers operating shows counterflow major advantage for this application

Calor e temperatura: uma revisão dos conceitos nas diferentes abordagens físicas

This work research and analyses the formulations and concepts of heat and temperature presented in Physics textbooks. These issues are deemed important because students often have difficulties differentiating and understanding such concepts, which compromises their education. The goal is to show that well-established relationships between Physical quantities such as energy, pressure, heat and temperature, even in different theories of Classical and Quantum Physics are not enough to define either temperature or heat. It also presents simple experiments that complement the teaching and learning of these concepts

Análise das propriedades da madeira de estrutura de telhado após a ocorrência de um incêndio

The present study evaluated the mechanical properties of pieces of wood coming from the roof structure of a residence subject fire in the rural area of Itapeva/SP. The structure was built 25 years ago using wooden beams of the species Guarucaia (Peltophorum vogelianum), where the specimens were removed. The research methodology included qualitative evaluation of the samples, estimating the layer pyrolysis and carbonization of the wood, measuring of density and mechanical tests of compression parallel to grain, tension parallel to grain and shear. The mechanical properties of wood were analytically correlated with the layers carbonization and pyrolysis that are influenced by the temperature and time of fire; these values were estimated at 1000 °C and two hours for the case in question. The results indicate that the strength properties of degraded wood are different from a healthy wood. The level of thermodegradation, in general, can be measured by density, result in weight loss due to decomposition of the wooden components.

Análise preliminar para a estimativa da perda de calor sensível de um fluido homogêneo térmico em um reservatório de geometria cilindrica

This work analyzed the loss of sensible heat from one fluid to be considered homogeneous heat distribution on a thermal reservoir with cylindrical geometries composite insulating layers. We studied two thermal reservoirs with a volume of 20 liters, and the first has a layer thickness of 75 mm of expanding polyurethane foam wrapped in the polycarbonate container and the second container has only layer thickness of 5 mm of polycarbonate, as insulation of fluid of the external environment. The experimental results are compared with theoretical results obtained through a calculation script, displayed and detailed during the work development, from the theory of energy balance. The maximum error introduced between the theoretical and experimental results were 3.5% and 1.4% respectively for the Boilers with or without a polyurethane coating

Comparação da eficiência térmica de trocadores de calor no laboratório de sistemas térmicos da Faculdade de Engenharia

This work aims to verify and compare the efficiency of heat exchangers used in the thermal systems laboratory at Faculdade de Engenharia do Campus de Guaratinguetá - UNESP. Basically, it has been studied two types of heat exchangers: plate type, operating in parallel flow and counter-flow, shell and tube type and also operating in parallel flow and counter flow. Initially it has been presented the didactic equipment and procedures for use of these heat exchangers in the proposed experiments. With the results obtained from the experiments, comparisons were made in order to define the behavior of the heat exchangers regarding some variables. In the study, one comes to the conclusion that the results from shell and tube type of heat exchanger, used in the thermal systems lab, are superior in all conditions analyzed

Estudo de um ciclo de vapor utilizado para tratamento de superificies metálicas: estudo preliminar de caso

The use of heat in parallel with relative low temperatures and applied to several areas of the industry is essential for the main manufacturing processes, like drying, dehydrating, concentration, annealing, production of chemical reactions, and microbiological sterilization. Without neither the heat nor the coming of a great quantity of thermal heat, with high quality, there would not be the “modern society”, with its high standards of living plus its high consumption levels; from services to goods in general. Within an almost absolute way, the heat flows are obtained from vapor systems. Thus, in this work we are going into the operation of a vapor system, composed of two firetube boilers dimensioned to supply vapor for three processes. However, with the transfer of one of the processes to another plant, the system got over-dimensioned. But, taking advantage of this scenario, the two boilers were used to supply vapor to further processes, causing their intermittent usage. Moreover, the operational alternative adopted by the maintenance engineering of the plant for a creating a solution has been presented; both the positive points and negative ones were disclosed, likewise the possibility of improvement points

Uma revisão sobre a resina uréia-formadeído (RUF) empregada na produção de painéis de madeira reconstituída

According to ABIPA (2009), Brazil is currently among the major producers of reconstituted wood panels, with one of the main factors for this condition, its climate and its large land area, which allows the cultivation of forests, which provide raw materials for these industries. To establish that market as power, Brazil has invested about R$ 1.3 billion in the last 10 years, yet designed an investment of 0.8 billion dollars over the next three years (BNDES, 2008). With the new investments in this segment, we expect a growth of about 66% in the resin consumption of urea-formaldehyde (GPC, 2009) which should also result in major investments by the companies producing this polymer. Currently employees are mainly three types of resins in the production industry panels, as follows: Urea-Formaldehyde Resin (R-UF), melamine-formaldehyde resin (R-MF) and Phenol-Formaldehyde Resin (R-FF). Especially the cost factor, the urea-formaldehyde resin is the most used by companies producing reconstituted wood panels. The UF-R is a polymer obtained by condensation of urea and formaldehyde reactors (usually batch type), characterized by being a thermosetting polymer which makes it very efficient for bonding wood composites. The urea-formaldehyde polymer, to present a quite complex, it becomes very difficult to predict the exact chain resulting in the process of condensation of urea with formaldehyde, so that a greater knowledge of its characteristics and methods for their characterization can result in greater control in industrial processes and subsequent decrease cost and improve the quality of reconstituted wood panels produced in Brazil

Análise exergética e ecológica de um sistema compacto de cogeração operando com gás de síntese

The aim of this work is to make a qualitatively and ecologically evaluation of a compact cogeneration system that operates with synthesis gas obtained from a gasifier. Using the Eucalyptus Biomass as fuel, that passes through a wood gasifier (Drowndraft type) and supply the internal combustion engine. The compact cogeneration system is composed of two heat exchangers, an energy generator connected to an internal combustion engine and an absorption refrigeration system. The complete system is installed in the laboratory from the Energy Department at the University of Guaratinguetá. By the analysis related to the First and Second Thermodynamic Laws applied in this system, was possible to identify the mass flows in each point, energetic efficiency, irreversibility and exergetic efficiency. The components that have the biggest irreversibilities are the gasifier, followed by the internal combustion engine, which should be focused in future improvements. The system efficiency in energetic basis is 51,84% and in exergetic basis is 22,78%. Using the ecologic efficiency methodology was possible to identify the emissions rates, the pollution indicator associated to the combustion of the synthesis gas in the internal combustion engine. The ecologic efficiency considering the energectic analysis is 91,73%, while considering the exergetic analysis, 83,65%. It is concluded that the use of the synthesis gas in a compact cogeneration system is viable from the technical and ecological point of view, making possible to generate energy for isolated communities and promoting the decentralized electricity generation

Obtenção de constantes elásticas da madeira de duas espécies de Pinus sp

There are many studies about longitudinal modulus of elasticity of wood, but you can´t say the same of transverse modulus, especially for conifers. The study aimed to characterize and compare the species Pinus elliottii var. elliottii and Pinus elliottii var. elliottii x Pinus cariabeae hondurensis (hybrid), and the longitudinal modulus of elasticity (E) and lateral (G) in bending, to analyze the modulus of elasticity in different spaces and to verify the species studied the ideal range is equal to 21 times the height of the specimen, as prescribed in the normative document NBR 7190/1997, as well as analyzing the relationship G = E/20 defined in the normative document NBR 7190/1997. The wood came from the farm located in Paranapanema, split at the mill São José and the rest of the work was conducted at the Experimental Itapeva Campus - UNESP. Were removed fourteen specimens of each species. The average values of the modulus of elasticity and cross were, respectively, 5828 MPa and 452 MPa for Pinus elliottii var. elliottii and 6407 MPa and 320 MPa for the species of Pinus elliottii var. elliottii x Pinus cariabeae hondurensis (hybrid). The trend lines for the plotted graphs showed an exponential behavior to near linear 21he will equal the constant after this value. We have found the relationship G = E/13, for Pinus elliottii var. elliottii and G = E/20 for hybrid. The results of the modulus and strength for Pinus elliottii var. elliottii and the hybrid were lower than those reported in the literature, showing that this batch inferior quality to apply to structures

Efeitos da variação do teor de umidade da madeira no processo de lixamento

The process of sanding wood is little known and industries use it in a practical way without having studied their best conditions before. There are few studies involving this type of machining. On this basis, this paper studied the effects of varying moisture content of the wood surface quality after the sanding process. It was used a sanding machine with flat horizontal cut parallel to the fibers, using: 02 different species (Pinus elliottii and Corymbia citriodora); 01 sanding abrasive (aluminum oxide) and 03 different particle size abrasives ( P80 , P100 and P120 ) . Initially, the pieces were acclimatized ( 2 ± 7% , 12% and 17% ± 2 ± 2 ) and subsequently passed by the sanding process, and therefore, the surface roughness was analyzed. For each condition, were performed 06 repetitions totaling 54 trials for each species. We analyzed the effects of wood moisture by capturing the power sanding, rougheness, acoustic emission and maximum temperature during the sanding process. The variation of moisture content produced changes in the surface quality of the finished parts, and these changes were more marked in Pinus than Corymbia. During the sanding process of the specimens with 7 % and 12 % humidity, there was a lower noise emission, power consumption and heating surface. When checking the roughness of these parts after this process, it was observed that the surface quality of them were superior in the parts sanded containing 17 % moisture

Ensaio de ligações de estruturas de madeira por chapas com dentes estampados em quatro espécies da família leguminosas

In the last years, the use of industrialized systems of lattice structures of wood as an alternative in the construction processes, is becoming more popular in Brazil, mainly for their commitment to the environment.The industrialized system of wooden lattice structures consists in a production of lattice structures, composed of pieces of wood where their mechanical connections are made with the sheet multi-toothed connectors (CDE).Among the many challenges to make this system competitive, the whole system of the connections between the pieces of wood not only must show functionality, but also speed, strength, versatility and economy. Referenced at Brazilian Standard for Wood Structures (NBR 7190/1997 - Project of timber structures) the sheet multi-toothed connectors, are analyzed using three test methods: tensile strength parallel to grain, tensile strength normal to the fibers and shear strength, all of them in two positions, αCH0=0o e αCH0=90o to four types of wood: Angelim (Vatairea heteroptera Ducke); Red-Angico (Parapiptadenia rigida (Benth) Brenae); Garapa (Apuleia leiocarpa (Vog.) Macbr) and Jatoba (Hymenaea stilbocarpa Hayne), belonging to the Leguminosae family and founded in several regions of Brazil.The purpose of this manuscript consists to analyze the mechanical connections with the sheet multi-toothed connectors through tests from NBR7190/1997

Iniciativa para integração da infraestrutura regional Sul-americana (IIRSA): a construção do complexo do Rio Madeira e seus impactos socioambientais

não disponível

Análise da troca de calor em sistemas de injeção de termoplásticos – um estudo de caso: polipropileno

The purpose of this work was to define the processes through which the cooling of thermoplastics parts occur inside the mold cavity in an injection process. The plastic materials have become more widespread in the automobile industry and, among its manufacturing processes, injection moulding develops quickly, allowing the manufacturing of quality parts in great volumes. Data was collected from the injection of Volkswagen Gol NF 23X (Gol Generation 5). Using approximated methods for calculation for the heat Exchange inside the mould, in the cooling system, the required water flow was determined to properly cool the parts. Comparing the obtained value with Project specifications, it was verified that the method, in spite of incurring in some mistakes, is efficient in determining the flow of cooling fluid and serves as a verification tool for the parameters defined on project, and can be applied to simple projects. The definition of the cooling system, in practice, is dependent on innumerable variables and each case must be approached in itself, since the parameters for one product may not be ideal for another

Estudo das propriedades mecânicas da madeira plástica

This work has in its outline the analysis of the mechanical properties of the composition of plastic residues, denominated “plastic wood”, aiming at establishing technical parameters for application of this material in substitution to the natural wood. Plastic-Wood is basically, a combination of several kind of plastic, previously selected, washed, dried and without metallic particles, which are agglomerated, extruded or introduced into a mold. The manufacturer can choose different formats and colors. During this monograph it can be observed the use of several kind of plastic, their mechanical properties and the plastic-wood production process. Also are presented features and applications of natural wood, in order to better compare their uses in several applications