Physical soil characteristics of waterlogged and saline lands of five districts of Haryana, India

Physical characteristics of waterlogged and saline soils of five districts, namely Rohtak, Faridabad, Gurgaon, Sonipat and Jhajjar, of Haryana were studied to evaluate the aquaculture potential. The soil samples from 76 sites were procured and analysed for pH, electrical conductivity, soil particles and water retention capacity, since the knowledge of these parameters is essential for the preliminary evaluation of a site for aqua-farming. Six soil types were identified and clay-loam was observed to be the maximum at 45 (59.21%) sites, followed by silty-clay loam at 14 (18.42%), sandy-clay loam at six (7.89%), silty-loam at four (5.26%), sandy-loam at four (5.26%) and loam at three (3.94%) sites. The pH of soil indicated moderate to high alkaline conditions ranging between 8.01and 9.00 at 53 (69.73%) sites, 9.01 and 10.00 at 17 (22.36%) sites, and low between 7.01 and 8.00 at six (7.89%) sites. The electrical conductivity was found to range between <1 and 10 mmho cmˉ¹ with the value of <1.0 mmho cmˉ¹ at 36 (47.36%) sites. The water retention capacity was observed mostly to be moderate. The paper describes the interrelationship between these parameters with reference to the suitability for aqua-farming.

Experimental and theoretical comparison between static and dynamic torsional soil tests

The dynamic properties of dry Leighton Buzzard sand have been investigated using a resonant column test apparatus. These data are compared with very low frequency cyclic tests on identical specimens of sand. The comparison indicates that the properties of dry sand are independent of frequency. A simple one-dimensional model of kinematic hardening plasticity is used to predict the dynamic behaviour of the sand. The input parameters for this model are based on the results of static tests. These may be conducted on standard laboratory equipment with only minor modifications. The predictions are in good agreement with the measured data.

The modelling of soil plasticity

The modeling of the soil plasticity was discussed and it was shown that the grain breakage is an important factor of the plastic soil behaviour. A reduction of internal coefficient of friction was observed when stress-level was increased. The yield paths of all stress path tests determined by curve fitting were presented.

Soil conditioning under London

The CTRL Contract 220 covered 7.5km twin-bore tunnels excavated between late 2002 and early 2004 from Stratford Box to St Pancras station in Central London. To ensure efficient machine operation as well as the transport and disposal of soil, soil conditioning treatments were applied. Specifically, the foam injection ratio (FIR) and the polymer injection ratio (PIR) (injected volume of foam and polymer solution expressed as a percentage of the excavated soil volume) were employed. It was found that carefully selected soil conditioning allowed chamber pressures of 200kPa or more to be accurately controlled in the stiff London Clay and to an extent, in the very stiff clays of the Lambeth Group. Average FIRs of 50% and PIRs of 7 and 9% were used in the Thanet Sand and in the Lambeth Group Clays. In contrast, much lower quantities of foam were used in the London Clay.

Dem analysis of soil-pipeline interaction in sand under lateral and upward movements at deep embedment

The soil-pipeline interactions under lateral and upward pipe movements in sand are investigated using DEM analysis. The simulations are performed for both medium and dense sand conditions at different embedment ratios of up to 60. The comparison of peak dimensionless forces from the DEM and earlier FEM analyses shows that, for medium sand, both methods show similar peak dimensionless forces. For dense sand, the DEM analysis gives more gradual transition of shallow to deep failure mechanisms than the FEM analysis and the peak dimensionless forces at very deep depth are higher in the DEM analysis than in the FEM analysis. Comparison of the deformation mechanism suggests that this is due to the differences in soil movements around the pipe associated with its particulate nature. The DEM analysis provides supplementary data of the soil-pipeline interaction in sand at deep embedment condition.

Vibration-assisted bone-graft compaction in impaction bone grafting of the femur

The complications of impaction bone grafting in revision hip replacement includes fracture of he femur and subsidence of the prosthesis. In this in vitro study we aimed to investigate whether the use of vibration, combined with a perforated tamp during the compaction of morsellised allograft would reduce peak loads and hoop strains in the femur as a surrogate marker of the risk of fracture and whether it would also improve graft compaction and prosthetic stability. We found that the peak loads and hoop strains transmitted to the femoral cortex during graft compaction and subsidence of the stem in subsequent mechanical testing were reduced. This innovative technique has the potential to reduce the risk of intra-operative fracture and to improve graft compaction and therefore prosthetic stability. © 2007 British Editorial Society of Bone and Joint Surgery.

Modelling effects of axial load on behaviour of pile groups in laterally-spreading soil

Previous research into the behaviour of piled foundations in laterally-spreading soil deposits has concentrated on pile groups that carry small or negligible axial loads. This paper presents dynamic centrifuge test results for 2 x 2 pile groups with bending and geometric properties similar to real 0.5 m diameter tubular steel and solid circular reinforced-concrete field piles. Axial loads applied represented upper-bounds on typical working loads. The simultaneous scaling of the relevant properties controlling both lateral and axial behaviour allows comparisons to be drawn regarding the particular mechanisms of failure that would dominate for each type of pile. Flexible reinforced-concrete piles which tend to carry lower loads were found to be dominated by lateral effects, while steel piles, which are much stiffer and usually carry greater loads are dominated by settlement considerations. © 2006 Taylor & Francis Group.

Sustainable binders for soil stabilisation

Portland cement is the most commonly and widely used binder in ground improvement soil stabilisation applications. However, many changes are now affecting the selection and application of stabilisation additives. These include the significant environmental impacts of Portland cement, increased use of industrial by-products and their variability, increased range of application of binders and the development of alternative cements and novel additives with enhanced environmental and technical performance. This paper presents results from a number of research projects on the application of a number of Portland cement-blended binders, which offer sustainability advantages over Portland cement alone, in soil stabilisation. The blend materials included ground granulated blastfurnace slag, pulverised fuel ash, cement kiln dust, zeolite and reactive magnesia and stabilised soils, ranging from sand and gravel to clay, and were assessed based on their mechanical performance and durability. The results are presented in terms of strength and durability enhancements offered by those blended binders.

Chryseobacterium flavum sp nov., isolated from polluted soil

A Gram-negative, non-motile, rod-shaped bacterial strain, designated CW-E 2(T), was isolated from a polluted soil sample collected from Jiangsu Province, China. A taxonomic study of the isolate, including phylogenetic analysis based on 16S rRNA gene seque

Pontibacter akesuensis sp nov., isolated from a desert soil in China

A Gram-negative, non-motile, rod-shaped bacterium, designated strain AKS 1 T, was isolated from a desert soil sample collected from Alkesu, Xin.lang Province, China. A taxonomic study, including phylogenetic analysis based on 16S rRNA gene sequences and p