Evaluation and comparison of ozone, hydrogen peroxide and physical treatment on fungal infection prevention and hatching rate of Iranian sturgeon (Acipenser persicus)

Ozone due to having low half-life and devoid of environmental harmful effects is recognized as one of the most effective disinfectant and fungicide in aquaculture. The objective of this study is to consider the effects of periodicay ozonation, hydrogen peroxide treatment, and physical treatment capability in hatching rate enhancement. Three concentrations of 0.05, 0.1 and 0.15 ppm ozone (10 min) and peroxide hydrogen with dose of 500 and 1000 ppm in two procedures accompanied with physical treatment and without physical treatment were examined on hatching rate. In the first year, Egg ozonation (0.1 ppm) with physical treatment have been resulted the greatest hatching rate (81.4%). In the second year, egg treatment with 1000 ppm hydrogen peroxide with physical treatment have been showed the greatest hatching rate (78%). Average hatching rate for the blank control treatment (without disinfectin and physical treatment) was 32.7%. From the economic viewpoint, 0.05 ppm ozone with physical treatment, due to considerable minimizing at consumption energy and ozonation system retention costs, indicated as the best treatment than other ozone treatments for fungal control. Very low correlation (r=-0.14) have been observed between hatchery water temperature and fungal infection percentage in control treatment.

Isolating and recognizing crudeoiklegrading [sic] bacteria of Queshm Island shores for biodegradation of crude oil pollutions

This research was carried out for recognizing Natural Flora Bacteria of oil pollution in the coasts of Queshm island. In The First steps, The coasts of this Island were scrutinized as a Field of research and For knowing whether oil stains exist or not. It gets obvious That southern coasts of Queshm have got oil pollution which is created by oil tankers which carry oil of Iran continental shelf. Them oil stains were sampled from to certain stations. In The First step, primary isolation of exisiting bacteria in every oil sample was done and then purification of each bacterium was carried out. Then each purified bacterium that has got strong, recognized, typic growth was enriched oil sample of T5 station. And Bacterium C4 (gram—negative coccobacillus) was chosen as the second priority From oil sample of TA station and Bacterium B1 (gram—positive coccus) was chosen as The third priority From oil sample of TI station. All The above mentioned bacteria were biochemically, physiologically and morphologically experimented For specking The species. According To The tests done and comparing with The tests done and comparing with the reference Berge y' s, bacterium A5 Pelongs to the species pseudomonas sp and becterium C4 belongs to the species Aeromonas sp and bacterium BI belongs to The species micrococcus sp. In The Last stage, bacterium with The First priority (TA5 pseudomonas sp) was used in the planned microcosm. The sake of optimum and adapting to Laboratory conditions Each enriched and purified bacterium was given a code for station and a code For itself . Then This bacterium was studied and it was proved that it has potentiality For using oil as a source of carbon. From oil samples of 10 stations, 30 various Colonies of bacterium were Isolated, of which 20 bacteria had the highest potentiality of growth. And the other bacteria that has no typic growth were omitted From being studied. Since all of These 20 bacterium are able to use oil, a bacterium with maximum rate of growth in the presence of crude oil and Lack of other hydrocarbonic sources and with The code A5 ( gram — negative Bacillus ) was chosen as First priority From The mentioned microcosm contains sea water , suspension oil degrading bacterium , crude oil, azote and various concentrations of carbon and Incubated in 30°` and shook 150 PRA1 According to the results , index oil degrading bacterium (pseudomonas sp) belongs oil sample of T5 stations (east of sheeb draz Gulf) which growth best and have the potentiality of degrading oil in 25 glli malas and 50 glli cheese water and with 5 gill urea .

The effects of a second tunnel on the propagation of ground-borne vibration from an underground railway

Accurate predictions of ground-borne vibration levels in the vicinity of an underground railway are greatly sought in modern urban centers. Yet the complexity involved in simulating the underground environment means that it is necessary to make simplifying assumptions about this environment. One such commonly-made assumption is to model the railway as a single tunnel, despite many underground railway lines consisting of twin-bored tunnels. A unique model for two tunnels embedded in a homogeneous, elastic full space is developed. The vibration response of this two-tunnel system is calculated using the superposition of two displacement fields: one resulting from the forces acting on the invert of a single tunnel, and the other resulting from the interaction between the tunnels. By partitioning of the stresses into symmetric and anti-symmetric mode number components using Fourier decomposition, these two displacement fields can by calculated with minimal computational requirements. The significance of the interactions between twin-tunnels is quantified by calculating the insertion gains that result from the existence of a second tunnel. The insertion-gain results are shown to be localized and highly dependent on frequency, tunnel orientation and tunnel thickness. At some locations, the magnitude of these insertion gains is greater than 20dB. This demonstrates that a high degree of inaccuracy exists in any surface vibration-prediction model that includes only one of the two tunnels. © 2012 Springer.

Ecodesign innovation: Is 'early' always 'best'?

This paper explores ecodesign within the product development process (PDP), particularly focusing on the design stages. Previous research has highlighted the early stages as the 'best' place to integrate environmental issues. Here the early stage hypothesis is explored from the perspective of the industrial design department - the early stage designers. Being located at the earliest possible design stages of product development would mean that, were the hypothesis to hold true, industrial design would be the 'best' place to locate ecodesign. Empirical research was conducted with the Industrial Design Centre (IDC) of a global Electrical and Electronic goods manufacture. It used a qualitative, inductive research methodology, based on two 'live' design concept projects, participant observation within the department, and on several semi-structured interviews. Throughout this paper, the empirical work is compared and contrasted to ecodesign literature, specifically to models of ecodesign innovation and the product development process. Beginning by exploring of the early stage hypothesis, the paper concludes with a conceptual model of early stage ecodesign for the context in question.

Gigacount/second photon detection with InGaAs avalanche photodiodes

We demonstrate high count rate single photon detection at telecom wavelengths using a thermoelectrically-cooled semiconductor diode. Our device consists of a single InGaAs avalanche photodiode driven by a 2 GHz gating frequency signal and coupled to a tuneable self-differencing circuit for enhanced detection sensitivity. We find the count rate is linear with the photon flux in the single photon detection regime over approximately four orders of magnitude, and saturates at 1 gigacount/s at high photon fluxes. This result highlights promising potential for APDs in high bit rate quantum information applications.

Measurements and calculations of transport AC loss in second generation high temperature superconducting pancake coils

Theoretical and experimental AC loss data on a superconducting pancake coil wound using second generation (2 G) conductors are presented. An anisotropic critical state model is used to calculate critical current and the AC losses of a superconducting pancake coil. In the coil there are two regions, the critical state region and the subcritical region. The model assumes that in the subcritical region the flux lines are parallel to the tape wide face. AC losses of the superconducting pancake coil are calculated using this model. Both calorimetric and electrical techniques were used to measure AC losses in the coil. The calorimetric method is based on measuring the boil-off rate of liquid nitrogen. The electric method used a compensation circuit to eliminate the inductive component to measure the loss voltage of the coil. The experimental results are consistent with the theoretical calculations thus validating the anisotropic critical state model for loss estimations in the superconducting pancake coil. © 2011 American Institute of Physics.

The application of STEM and in situ controlled dehydration to bacterial systems using ESEM.

Transmission imaging with an environmental scanning electron microscope (ESEM) (Wet STEM) is a recent development in the field of electron microscopy, combining the simple preparation inherent to ESEM work with an alternate form of contrast available through a STEM detector. Because the technique is relatively new, there is little information available on how best to apply this technique and which samples it is best suited for. This work is a description of the sample preparation and microscopy employed by the authors for imaging bacteria with Wet STEM (scanning transmission electron microscopy). Three different bacterial samples will be presented in this study: first, used as a model system, is Escherichia coli for which the contrast mechanisms of STEM are demonstrated along with the visual effects of a dehydration-induced collapse. This collapse, although clearly in some sense artifactual, is thought to lead to structurally meaningful morphological information. Second, Wet STEM is applied to two distinct bacterial systems to demonstrate the novel types of information accessible by this approach: the plastic-producing Cupriavidus necator along with wild-type and ΔmreC knockout mutants of Salmonella enterica serovar Typhimurium. Cupriavidus necator is shown to exhibit clear internal differences between bacteria with and without plastic granules, while the ΔmreC mutant of S. Typhimurium has an internal morphology distinct from that of the wild type.

Study of second generation, high-temperature superconducting coils: Determination of critical current

This paper presents the modeling of second generation (2 G) high-temperature superconducting (HTS) pancake coils using finite element method. The axial symmetric model can be used to calculate current and magnetic field distribution inside the coil. The anisotropic characteristics of 2 G tapes are included in the model by direct interpolation. The model is validated by comparing to experimental results. We use the model to study critical currents of 2 G coils and find that 100μV/m is too high a criterion to determine long-term operating current of the coils, because the innermost turns of a coil will, due to the effect of local magnetic field, reach their critical current much earlier than outer turns. Our modeling shows that an average voltage criterion of 20μV/m over the coil corresponds to the point at which the innermost turns' electric field exceeds 100μV/m. So 20μV/m is suggested to be the critical current criterion of the HTS coil. The influence of background field on the coil critical current is also studied in the paper. © 2012 American Institute of Physics.

The application of STEM and in situ controlled dehydration to bacterial systems using ESEM

Transmission imaging with an environmental scanning electron microscope (ESEM) (Wet STEM) is a recent development in the field of electron microscopy, combining the simple preparation inherent to ESEM work with an alternate form of contrast available through a STEM detector. Because the technique is relatively new, there is little information available on how best to apply this technique and which samples it is best suited for. This work is a description of the sample preparation and microscopy employed by the authors for imaging bacteria with Wet STEM (scanning transmission electron microscopy). Three different bacterial samples will be presented in this study: first, used as a model system, is Escherichia coli for which the contrast mechanisms of STEM are demonstrated along with the visual effects of a dehydration-induced collapse. This collapse, although clearly in some sense artifactual, is thought to lead to structurally meaningful morphological information. Second, Wet STEM is applied to two distinct bacterial systems to demonstrate the novel types of information accessible by this approach: the plastic-producing Cupriavidus necator along with wild-type and δmreC knockout mutants of Salmonella enterica serovar Typhimurium. Cupriavidus necator is shown to exhibit clear internal differences between bacteria with and without plastic granules, while the δmreC mutant of S. Typhimurium has an internal morphology distinct from that of the wild type. © 2012 Wiley Periodicals, Inc.

Alternating current loss of second-generation high-temperature superconducting coils with magnetic and non-magnetic substrate

It is widely believed that the second-generation high-temperature superconducting (2G HTS) tapes with magnetic substrates suffer higher transport loss compared to those with non-magnetic substrates. To test this, we prepared two identical coils with magnetic and non-magnetic substrates, respectively. The experimental result was rather surprising that they generated roughly the same amount of transport loss. We used finite element method to understand this result. It is found that, unlike in the single tape where the magnetic field-dependent critical current characteristic can be neglected and the effect of magnetic substrate dominates, the magnetic field-dependent critical current characteristic of 2G tape plays as an equally important role as magnetic substrate in terms of HTS coils. © 2012 American Institute of Physics.