Activation of polymer blend carbon nanofibres by alkaline hydroxides and their hydrogen storage performances

In the present work we study the hydroxide activation (NaOH and KOH) of phenol-formaldehyde resin derived CNFs prepared by a polymer blend technique to prepare highly porous activated carbon nanofibres (ACNFs). Morphology and textural characteristics of these ACNFs were studied and their hydrogen storage capacities at 77 K (at 0.1 MPa and at high pressures up to 4 MPa) were assessed, and compared, with reported capacities of other porous carbon materials. Phenol-formaldehyde resin derived carbon fibres were successfully activated with these two alkaline hydroxides rendering highly microporous ACNFs with reasonable good activation process yields up to 47 wt.% compared to 7 wt.% yields from steam activation for similar surface areas of 1500 m2/g or higher. These nano-sized activated carbons present interesting H2 storage capacities at 77 K which are comparable, or even higher, to other high quality microporous carbon materials. This observation is due, in part, to their nano-sized diameters allowing to enhance their packing densities to 0.71 g/cm3 and hence their resulting hydrogen storage capacities.

Valoración energética de subproductos de palmera datilera

Este trabajo se integra en el marco de un estudio de valoración energética de subproductos obtenidos de la palmera datilera, disponibles en grandes cantidades y que actualmente no se valorizan. El objetivo principal de este trabajo consiste en evaluar los subproductos de la palmera datilera, y en concreto, estudiar el poder calorífico superior de las principales especies presentes en los oasis, y en obtener, mediante pirolisis de estos subproductos, carbón activo, y de esta al forma valorar residuos, obtener un aprovechamiento económico secundario, al mismo tiempo que estamos valorando estos residuos. El estudio se realiza sobre siete especies arbóreas, entre ellas cinco variedades de palmera datiliera, y en concreto sobre un único subproducto. Los resultados de estas pruebas permitieron poner de manifiesto que el Poder Calorífico de las especies que habitan los oasis es más importante que el de las otras especies arbóreas. El residuo sólido se obtiene de la madera de la parte inferior del árbol que se llama (Kornaf), activada a una temperatura de 700 °C utilizando el vapor de agua como agente de activación. Se estudió la calidad del carbón activo obtenido, mediante el cálculo de su superficie específica, y resultó de buena calidad (1050m2/g).

NaOH and KOH for preparing activated carbons used in energy and environmental applications

Alkaline hydroxides, especially sodium and potassium hydroxides, are multi-million-ton per annum commodities and strong chemical bases that have large scale applications. Some of them are related with their consequent ability to degrade most materials, depending on the temperature used. As an example, these chemicals are involved in the manufacture of pulp and paper, textiles, biodiesels, soaps and detergents, acid gases removal (e.g., SO2) and others, as well as in many organic synthesis processes. Sodium and potassium hydroxides are strong and corrosive bases, but they are also very stable chemicals that can melt without decomposition, NaOH at 318ºC, and KOH at 360ºC. Hence, they can react with most materials, even with relatively inert ones such as carbon materials. Thus, at temperatures higher than 360ºC these melted hydroxides easily react with most types of carbon-containing raw materials (coals, lignocellulosic materials, pitches, etc.), as well as with most pure carbon materials (carbon fibers, carbon nanofibers and carbon nanotubes). This reaction occurs via a solid-liquid redox reaction in which both hydroxides (NaOH or KOH) are converted to the following main products: hydrogen, alkaline metals and alkaline carbonates, as a result of the carbon precursor oxidation. By controlling this reaction, and after a suitable washing process, good quality activated carbons (ACs), a classical type of porous materials, can be prepared. Such carbon activation by hydroxides, known since long time ago, continues to be under research due to the unique properties of the resulting activated carbons. They have promising high porosity developments and interesting pore size distributions. These two properties are important for new applications such as gas storage (e.g., natural gas or hydrogen), capture, storage and transport of carbon dioxide, electricity storage demands (EDLC-supercapacitors-) or pollution control. Because these applications require new and superior quality activated carbons, there is no doubt that among the different existing activating processes, the one based on the chemical reaction between the carbon precursor and the alkaline hydroxide (NaOH or KOH) gives the best activation results. The present article covers different aspects of the activation by hydroxides, including the characteristics of the resulting activated carbons and their performance in some environment-related applications. The following topics are discussed: i) variables of the preparation method, such as the nature of the hydroxide, the type of carbon precursor, the hydroxide/carbon precursor ratio, the mixing procedure of carbon precursor and hydroxide (impregnation of the precursor with a hydroxide solution or mixing both, hydroxide and carbon precursor, as solids), or the temperature and time of the reaction are discussed, analyzing their effect on the resulting porosity; ii) analysis of the main reactions occurring during the activation process, iii) comparative analysis of the porosity development obtained from different activation processes (e.g., CO2, steam, phosphoric acid and hydroxides activation); and iv) performance of the prepared activated carbon materials on a few applications, such as VOC removal, electricity and gas storages.

Activation of a spherical carbon for toluene adsorption at low concentration

This paper complements a previous one [1] about toluene adsorption on a commercial spherical activated carbon and on samples obtained from it by CO2 or steam activation. The present paper deals with the activation of a commercial spherical carbon (SC) having low porosity and high bed density (0.85 g/cm3) using the same procedure. Our results show that SC can be well activated with CO2 or steam. The increase in the burn-off percentage leads to an increase in the gravimetric adsorption capacity (more intensively for CO2) and a decrease in bed density (more intensively for CO2). However, for similar porosity developments similar bed densities are achieved for CO2 and steam. Especial attention is paid to differences between both activating agents, comparing samples having similar or different activation rates, showing that CO2 generates more narrow porosity and penetrates more inside the spherical particles than steam. Steam activates more from the outside to the interior of the spheres and hence produces larger spheres size reductions. With both activation agents and with a suitable combination of porosity development and bed density, quite high volumetric adsorption values of toluene (up to 236 g toluene/L) can be obtained even using a low toluene concentration (200 ppmv).

X-Ray Imaging of SAPO-34 Molecular Sieves at the Nanoscale: Influence of Steaming on the Methanol-to-Hydrocarbons Reaction

The effect of a severe steaming treatment on the physicochemical properties and catalytic performance of H-SAPO-34 molecular sieves during the methanol-to-hydrocarbons (MTH) reaction has been investigated with a combination of scanning transmission X-ray microscopy (STXM), catalytic testing, and bulk characterization techniques, including ammonia temperature programmed desorption and 27Al and 29Si magic angle spinning nuclear magnetic resonance. For this purpose, two samples, namely a calcined and a steamed H-SAPO-34 catalyst powder, have been compared. It has been found that calcined H-SAPO-34 displays a high selectivity towards light olefins, yet shows a poor stability as compared to a zeolite H-ZSM-5 catalyst. Moreover, in situ STXM at the carbon K-edge during the MTH reaction allows construction of nanoscale chemical maps of the hydrocarbon species formed within the H-SAPO-34 aggregates as a function of reaction time and steam post-treatment. It was found that there is an initial preferential formation of coke precursor species within the core of the H-SAPO-34 aggregates. For longer times on stream the formation of the coke precursor species is extended to the outer regions, progressively filling the entire H-SAPO-34 catalyst particle. In contrast, the hydrothermally treated H-SAPO-34 showed similar reaction selectivity, but decreased activity and catalyst stability with respect to its calcined counterpart. These variations in MTH performance are related to a faster and more homogeneous formation of coke precursor species filling up the entire steamed H-SAPO-34 catalyst particle. Finally, the chemical imaging capabilities of the STXM method at the Al and Si K-edge are illustrated by visualizing the silicon islands at the nanoscale before and after steaming H-SAPO-34.

Gasification and pyrolysis of Posidonia oceanica in the presence of dolomite

In the present work, a very detailed study of the reforming of syngas produced in the decomposition of Posidonia oceanica is done. The effect of the presence of different amounts of dolomite is analyzed. Also pyrolysis is studied, in nitrogen atmosphere, and gasification in the presence of air, oxygen and different amounts of steam. A detailed discussion on formation and destruction of tars is done. Furthermore, the effect of the heating rate in the decomposition and the residence time of the evolved gases are discussed. Syngas with ratio H2/CO from 0.3 to ca. 3 can be obtained from this interesting material. Marine species (microalgae) are usually studied with the aim of cultivating them for gas or oil production, but in this paper we draw attention to the possibility of using a natural resource with a very small impact in the ecosystem.

Gasification and Pyrolysis of Posidonia oceanica in the Presence of Dolomite

Resumen del póster presentado en Symposium on Renewable Energy and Products from Biomass and Waste, CIUDEN (Cubillos de Sil, León, Spain), 12-13 May 2015

Steamboats and pleasure travels: success and failure of the first Spanish initiatives in the mid-nineteenth century

Steam technology revolutionised maritime transport during the nineteenth century. Together with the establishment of the first regular lines, steamers soon led to the commencement of pleasure navigation. The aim of this article is to analyse the impact and scope of this process in Spain, by means of a study of the first experiences in the mid-nineteenth century. In addition to a brief introduction and final conclusions, the paper is structured around four sections. The first contains an appraisal of the situation of passenger transport. Some information is then provided regarding the first cruise in 1854. Next, the essay highlights some of the features of short excursions that were very well received by the public, especially in the island of Majorca. Finally, attention is given to a very special type of travel, the main attraction of which lay in the opportunity to witness an event of a military nature.

Hope: a poem delivered at an exhibition in Cambridge, July 10, 1800

This four-page handwritten poem was composed by Harvard student Joseph Mansfield for a College exhibition on July 8, 1800. The poem begins, "I am not blesd, but may hereafter be; / Who knows what fortune has in store for me?" and concludes with verses about the American Revolutionary War and George Washington.

Letter from Daniel W. Coit to William Tudor,

One letter regarding the ownership of a steam engine, a silver mine in Catajumbo, and prices of goods and foodstuffs.

Birds eye view of trolley routes in New England, 1904 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Trolley wayfinder, birds eye view of trolley routes in New England, published by the New England Street Railway Club, 1904. This is a perspective map not drawn to scale. Covers eastern portion of New England from Lewiston, Maine, to Newport, Rhode Island. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Massachusetts State Plane Coordinate System, Mainland Zone (in Feet) (Fipszone 2001). All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, or other information associated with the principal map. This map shows features such as steam railroads, electric railroads, parks, buildings, drainage, and more. Relief and some features are shown pictorially. Includes 7 insets. This layer is part of a selection of digitally scanned and georeferenced historic maps of Massachusetts from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of regions, originators, ground condition dates (1755-1922), scales, and purposes. The digitized selection includes maps of: the state, Massachusetts counties, town surveys, coastal features, real property, parks, cemeteries, railroads, roads, public works projects, etc.

Manhattan, New York, N.Y., ca. 1883 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Map of the city of New York : with street directory showing house-numbers, hotels, churches, banks, theatres, ferries, house-car, steam and elevated R.R'ds, &c. It was published by M. Dripps ca. 1883. Scale [ca. 1:12,670]. Covers Manhattan below 61st St. and portions of Brooklyn and Queens. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Universal Transverse Mercator (UTM) Zone 18N NAD83 projection. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as roads, railroads, drainage, selected public buildings, parks, wharves, ferry lines, city wards, and more. Depths shown by soundings. Includes directories of streets and places of interest, table of dimensions of the East River Bridge, and horse car routes. This layer is part of a selection of digitally scanned and georeferenced historic maps from The Harvard Map Collection as part of the Imaging the Urban Environment project. Maps selected for this project represent major urban areas and cities of the world, at various time periods. These maps typically portray both natural and manmade features at a large scale. The selection represents a range of regions, originators, ground condition dates, scales, and purposes.

Chicago and vicinity, Illinois, 1893 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Rand McNally and Co.'s standard map of Chicago, Rand, McNally & Co., engravers. It was published by Rand McNally & Co. in 1893. Scale [ca. 1:20,000]. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Illinois East State Plane Coordinate System NAD83 (in Feet) (Fipszone 1201). All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as roads, railroads (steam and elevated), depots, cable and horse car lines, drainage, boulevards and parks, ward boundaries, selected public buildings, and more. Includes index to streets, avenues, and parks and list of railroads and their depots. This layer is part of a selection of digitally scanned and georeferenced historic maps from The Harvard Map Collection as part of the Imaging the Urban Environment project. Maps selected for this project represent major urban areas and cities of the world, at various time periods. These maps typically portray both natural and manmade features at a large scale. The selection represents a range of regions, originators, ground condition dates, scales, and purposes.

Boston Harbor, Massachusetts, 1865 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Boston Harbor : showing the steamboat routes to places of amusement, engraved by G.W. Boynton. It was published by J.H. Daniels in 1865. Scale [ca. 1:63,360]. Covers Boston Harbor and adjacent lands. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Massachusetts State Plane Coordinate System, Mainland Zone (in Feet) (Fipszone 2001). All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, or other information associated with the principal map. This map shows coastal features such as rocks, shoals, light houses, beacons, channels, steam boat routes and landings, points, coves, islands, and more. Depths are shown by shading. It also shows land features such as roads, settlements, forts, drainage, and more. Relief is shown by hachures. This layer is part of a selection of digitally scanned and georeferenced historic maps of Massachusetts from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of regions, originators, ground condition dates (1755-1922), scales, and purposes. The digitized selection includes maps of: the state, Massachusetts counties, town surveys, coastal features, real property, parks, cemeteries, railroads, roads, public works projects, etc.

Boston and vicinity, Massachusetts, railroads, 1865 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Rail road map : showing the street rail road routes in and leading from Boston, with the terminus of each road in suburban cities or towns, prepared by J.G. Chase, civil engineer. It was published by J.H. Bufford in 1865. Scale [1:42,240]. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Massachusetts State Plane Coordinate System, Mainland Zone (in Feet) (Fipszone 2001). All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, or other information associated with the principal map. This map shows features such as street railroads, steam railroads, selected roads, drainage, town boundaries and more. This layer is part of a selection of digitally scanned and georeferenced historic maps of Massachusetts from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of regions, originators, ground condition dates (1755-1922), scales, and purposes. The digitized selection includes maps of: the state, Massachusetts counties, town surveys, coastal features, real property, parks, cemeteries, railroads, roads, public works projects, etc.