Numerical and experimental study of the thermal behaviour of coining and upsetting processes

A numerical simulation technique has been employed to study the thermal behavior of hot-forging type forming processes. Experiments on the coining and upsetting of an aluminum billet were conducted to validate the numerical predictions. Typical forming conditions for both the coining and upsetting processes were then studied in detail. an electrical analogy scheme was used to determine the thermal contact resistance. This scheme can conviniently provide the interface characteristics for typical processing conditions, which normally involve high pressures and temperatures. A single forging cycle was first considered, and then a batch of twenty-five forgings was studied. Each forging cycle includes the billet mounting, ascent, loading, dwelling, unloading, descent, and billet removal stages. The temperature distribution in the first forging to be formed is found to be significantly different from that at the end of the batch. In industry, forging is essentially a batch operation. The influence of forming speed and reduction on thermal characteristics was investigated also. The variations that can occur in the process design by considering differences in temperature characteristics are discussed also.

Prediction of load-deflection behaviour using fracture energy GF: A comparative study of two fracture models for concrete

Load-deflection curves for a notched beam under three-point load are determined using the Fictitious Crack Model (FCM) and Blunt Crack Model (BCM). Two values of fracture energy GF are used in this analysis: (i) GF obtained from the size effect law and (ii) GF obtained independently of the size effect. The predicted load-deflection diagrams are compared with the experimental ones obtained for the beams tested by Jenq and Shah. In addition, the values of maximum load (Pmax) obtained by the analyses are compared with the experimental ones for beams tested by Jenq and Shah and by Bažant and Pfeiffer. The results indicate that the descending portion of the load-deflection curve is very sensitive to the GF value used.

Reduction behaviour of Fe3+/Al2O3 obtained from the mixed oxalate precursor and the formation of the Fe0-Al2O3 metal-ceramic composite

Reduction behaviour of Fe3+/Al2O3 obtained by the decomposition of the oxalate precursor has been investigated by employing X-ray diffraction (XRD), Mössbauer spectroscopy and electron paramagnetic resonance (EPR) spectroscopy. Calcination of Fe3+/Al2O3 at or below 1070 K yields mainly a poorly ordered, fine particulate form of ?-Al2�xFexO3. Calcination at or above 1220 K yields ?-Al2�xFexO3. Reduction of Fe3+/Al2O3 samples calcined at or below 1070 K gives the FeAl2O4 spinel on reduction at 870 K; samples calcined at or above 1220 K give Al2-xFexO3 with a very small proportion of metallic iron. Fe3+/Al2O3 samples calcined at 1220 K or above yield metallic iron and a very small proportion of the spinel on reduction below 1270 K. In the samples reduced at or above 1270 K, the main product is metallic iron in both ferromagnetic and superparamagnetic forms. The oxalate precursor route yields more metallic iron than the sol�gel route.

An Analysis of the Concept of Citizenship: Legal, Political and Social Dimensions

The thesis aims at analyzing concept of citizenship in political philosophy. The concept of citizenship is a complex one: it does not have a definitive explication, but it nevertheless is a very important category in contemporary world. Citizenship is a powerful ideal, and often the way a person is treated depends on whether he or she has the status of a citizen. Citizenship includes protection of a person’s rights both at home and abroad. It entails legal, political and social dimension: the legal status as a full member of society, the recognition of that status by fellow citizens and acting as a member of society. The thesis discusses these three dimensions. Its objective is to show how all of them, despite being insufficient in some aspects, reach something important about the concept. The main sources of the thesis are Civic Republicanism by Iseult Honohan (Routledge 2002), Republicanism by Philip Pettit (Clarendon Press 1997), and Taking Rights Seriously by Ronald Dworkin (1997). In addition, the historical part of the thesis relies mainly on the works of Aristotle, Immanuel Kant, Adam Smith, Quentin Skinner, James Pocock and James Tully. The writings of Will Kymlicka, John Rawls, Chantal Mouffe, and Shane Phelan are referred to in the presentation and critique of the liberal tradition of thought. Hannah Arendt and Seyla Benhabib’s analysis of Arendt’s philosophy both address the problematic relations between human rights and nation-states as the main guarantors of rights. The chapter on group rights relies on Peter Jones’ account of corporate and collective rights, after which I continue to Seumas Miller’s essay on the (liberal) account of group rights and their relation to the concept of citizenship. Republicanism and Political Theory (2002) edited by Cécile Laborde and John Maynor is also references. David Miller and Maurizio Viroli represent the more “rooted” version of republicanism. The thesis argues that the full concept of citizenship should be seen as containing legal, political and social dimensions. The concept can be viewed from all of these three angles. The first means that citizenship is connected with certain rights, like the right to vote or stand for election, the right to property and so on. In most societies, the law guarantees these rights to every citizen. Then there is also the social dimension, which can be said to be as important as the legal one: the recognition of equality and identities of others. Finally, there is the political dimension, meaning the importance of citizens’ participation in the society, which is discussed in connection with the contemporary account of republicanism. All these issues are discussed from the point of view of groups demanding for group-specific rights and equal recognition. The challenge with these three aspects of citizenship is, however, that they are difficult to discuss under one heading. Different theories or discourses of citizenship each approach the subject from different starting points, which make reconciling them sometimes hard. The fundamental questions theories try to answer may differ radically depending on the theory. Nevertheless, in order to get the whole image of what the citizenship discourses are about all the aspects deserve to be taken into account.

Thermomechanical behaviour of pin joints subjected to sheet loads

An important problem regarding pin joints in a thermal environment is addressed. The motivation emerges from structural safety requirements in nuclear and aerospace engineering. A two-dimensional model of a smooth, rigid misfit pin in a large isotropic sheet is considered as an abstraction. The sheet is subjected to a biaxial stress system and far-field unidirectional heat flow. The thermoelastic analysis is complex due to non-linear load-dependent contact and separation conditions at the pin-hole interface and the absence of existence and uniqueness theorems for the class of frictionless thermoelastic contact problems. Identification of relevant parameters and appropriate synthesis of thermal and mechanical variables enables the thermomechanical generalization of pin-joint behaviour. This paper then proceeds to explore the possibility of multiple solutions in such problems, especially interface contact configuration.

A23187—Channel behaviour: Fluorescence study

Pyranine entrapped soylipid liposomes have been used as a model system to study the proton transport across membrane in the presence of A23187, a carboxylic ionophore specific for electroneutral exchange of divalent cations. An apparent rate constant (k(app)) for transport of protons has been determined from the rate of change of fluorescence intensity of pyranine by stopped flow rapid kinetics in the presence of proton gradient. The variation of k(app) has been studied as a function of ionophore concentration and the results have been compared with gramicidin-a well known channel former under the similar experimental conditions. The rates thus obtained showed that A23187 is not only a simple carrier but also shows channel behaviour at high concentration of ionophore.

Friction and wear behaviour of continuous fibre as cast Kevlar-phenolic resin composite

A compression moulded Kevlar-phenolic resin composite consisting of 30 wt% continuous fibres was slid against a steel disc such that the fibre axis was normal to the sliding plane. The sliding experiments were conducted in a normal pressure range of 0.47–4.27 MPa and at a sliding speed of 0.5 ms–1. The initial sliding interaction is abrasive. With further sliding, as patches of polymer transfer film develop on the polymer pin and counterface, the interaction becomes adhesive and steady-state friction is established. The wear resistance of the polymer was found to be related to the stability of this film.

Behaviour of the germ cell specific lamin through mammalian spermatogenesis as probed with monoclonal antibodies.

We had earlier identified a 60 kDa nuclear lamin protein (lamin(g)) unique to the germ cells of rat testis which was subsequently shown to be antigenically conserved in germ cells of grasshopper, rooster, frog and plants. We have now obtained eight monoclonal antibodies in mouse against this lamin(g) antigen. While all the eight Mabs reacted with lamin(g) antigen in an immunoblot analysis, only three Mabs (A(11)C(7), A(11)D(4), C1F7) showed strong reactivity in the immunofluorescence analysis of the germ cells. The Mabs A(11)C(7) and A(11)D(4) showed a slight cross-reactivity with rat liver lamin B. Indirect immunofluorescence analysis of pre-meiotic, meiotic and post-meiotic germ cells with Mabs have shown that while the lamin(g) is localized in the lamina structures of spermatogonia and round spermatids, it is localized to the phase dense regions of pachytene spermatocytes which is in conformity with our previous observations using rabbit polyclonal antibodies. The localization of the antigen in the germ cells was also confirmed by immunohistochemical staining of the thin sections of seminiferous tubules. By immunostaining the surface spread pachytene spermatocytes, the antigen was further localized to the telomeric ends of the paired homologous chromosomes. Using anti-somatic lamin B antibodies, we have also demonstrated the absence of somatic lamins in meiotic and post-meiotic germ cells. The lamina structure of pre-meiotic spermatogonial nucleus contains both somatic lamin B and lamin(g) as evidenced by immunofluorescence studies with two differently fluorochrome labelled anti-lamin B and anti-lamin(g) antibodies. The selective retention of lamin(g) in the pachytene spermatocytes is probably essential for anchoring the telomeric ends of the paired chromosomes to the inner nuclear membrane.

Copper( 11) Complexes of Novel Tripodal Ligands containing Phenolate and Benzimidazole/Pyridine Pendants: Synthesis, Structure, Spectra and Electrochemical Behaviour

Mononuclear copper(II) complexes of tri- and tetra-dentate tripodal ligands containing phenolic hydroxyl and benzimidazole or pyridine groups have been isolated. They are of the type (CuL(X)].nH2O, [CuL(H2O)]X.nH2O or [CuL].nH2O where X = Cl-, ClO4-, N3- or NCS- and n = 0-4. The electronic spectra of all the complexes exhibit a broad absorption band around 14000 cm-1 and the polycrystalline as well as the frozen-solution EPR spectra are axial, indicating square-based geometries. The crystal structure of [CuL(Cl)] [HL = (2-hydroxy-5-nitrobenzyl)bis(2-pyridyl-methyl)amine] revealed a square-pyramidal geometry around Cu(II). The mononuclear complex crystallises in the triclinic space group P1BAR with a = 6.938(1), b = 11.782(6), c = 12.678(3) angstrom and alpha = 114.56(3), beta = 92.70(2), gamma = 95.36(2)-degrees. The co-ordination plane is comprised of one tertiary amine and two pyridine nitrogens and a chloride ion. The phenolate ion unusually occupies the axial site, possibly due to the electron-withdrawing p-nitro group. The enhanced pi delocalisation involving the p-nitrophenolate donor elevates the E1/2 values. The spectral and electrochemical results suggest the order of donor strength as nitrophenolate < pyridine < benzimidazole in the tridentate and nitrophenolate < benzimidazole < pyridine in the tetradentate ligand complexes.

A study of microstructure and wear behaviour of TiB2/Al metal matrix composites

The present paper deals with the study of microstructure and wear characteristics of TiB2 reinforced aluminium metal matrix composites (MMCs). Matrix alloys with 5, 10 and 15% of TiB2 were made using stir casting technique. Effect of sliding velocity on the wear behaviour and tribo-chemistry of the worn surfaces of both matrix and composites sliding against a EN24 steel disc has been investigated under dry conditions. A pin-on-disc wear testing machine was used to find the wear rate, in which EN24 steel disc was used as the counter face, loads of 10-60N in steps of 10N and speeds of 100, 200, 300, 400 and 500 rpm were employed. The results showed that the wear rate was increased with an increase in load and sliding speed for both the materials. However, a lower wear rate was obtained for MMCs when compared to the matrix alloys. The wear transition from slight to severe was presented at the critical applied loads. The transition loads for the MMCs were much higher than that of the matrix alloy. The transition loads were increased with increase in TiB2 and the same was decreased with the increase of sliding speeds. The SEM and EDS analyses were undertaken to demonstrate the effect of TiB2 particles on the wear mechanism for each conditions.

Effect of microstructure on the creep behaviour of Ti-24Al-11Nb

In this investigation, the influence of microstructure on the high temperature creep behaviour of Ti-24Al-11Nb alloy has been studied. Different microstructures are produced by devising suitable heat treatments from the beta phase field. Creep tests are conducted in the temperature range of 923-1113 K, over a wide stress range at each temperature, employing the impression creep technique. The creep behaviour is found tb be sensitive to the crystallographic texture as well as to the details of microstructure. Best creep resistance is shown when the microstructure contains smaller alpha(2) plates and a lower beta volume fraction. This can be understood in terms of the dislocation barriers offered by alpha(2) beta boundaries and the case of plastic flow in the beta phase at high temperatures.

Characterization of hot deformation behaviour of Zr---2.5Nb---0.5Cu using processing maps

The characteristics of hot deformation of beta-quenched Zr-2.5Nb-0.5Cu in the temperature range 650-1050 degrees C and in the strain rate range 0.001-100 s(-1) have been studied using hot compression testing. For this study, the approach of processing maps has been adopted and their interpretation done using the Dynamic Materials Model. The efficiency of power dissipation given by [2m/(m + 1)], where m is strain rate sensitivity, is plotted as a function of temperature and strain rate to obtain a processing map. The processing map for Zr-2.5Nb-0.5Cu within (alpha + beta) phase field showed a domain of dynamic recrystallization, occurring by shearing of alpha-platelets followed by spheroidization, with a peak efficiency of 48% at 750 degrees C and 0.001 s(-1). The stress-strain curves in this domain had features of continuous flow softening and all these are similar to that in Zr-2.5Nb alloy. In the beta-phase field, a second domain with a peak efficiency of 47% occurred at 1050 degrees C and 0.001 s(-1) and this domain is correlated with the superplasticity of beta-phase. The beta-deformation characteristics of this alloy are similar to that observed in pure beta-zirconium with large grain size. Analysis of flow instabilities using a continuum criterion revealed that the Zr-2.5Nb-0.5Cu exhibits flow localization at temperatures higher than 800 degrees C and strain rates higher than about 30 s(-1) and that the addition of copper to Zr-2.5Nb reduces its susceptibility to flow instability, particularly in the (alpha + beta) phase field.