Identification and dissolution behavior of the secondary uranium minerals in the corrosion products of Depleted Uranium (DU) ammunition formed in soils

In der vorliegenden Studie wurden verschiedene Techniken eingesetzt um drei Proben (4, 7, and 8) die aus denrnKorrosionsprodukten von aus dem Kosovo Krieg stammenden Munitionskugeln, bestehend aus abgereichertem Uranrn(Depleted Uranium - DU), zu untersuchen. Als erstes Verfahren wurde die Raman-Spektroskopie eingesetzt. Hierbeirnzeigte sichin den Proben, charakterisiert durch einen Doppelpeak, die Anwesenheit von Schoepitrn(UO2)8O2(OH)12(H2O)12. Der erste und zweite Peakzeigte sich im Spektralbereich von 840,3-842,5 cm-1rnbeziehungsweise 853,6-855,8 cm-1. Diese Werte stimmen mit den Literaturwerten für Raman-Peaks für Schoepitrnüberein. Des Weiteren wurde bei dieser Untersuchungsmethode Becquerelite Ca(UO2)6O4(OH)6(H2O)8 mit einemrnPeak im Bereich zwischen 829 to 836 cm-1 gefunden. Aufgrund des Fehlens des Becquerelitespektrums in derrnSpektralbibliothek wurde eine in der Natur vorkommende Variante analysiert und deren Peak bei 829 cm-1 bestimmt,rnwas mit den Ergebnissen in den Proben korrespondiert. Mittels Röntgenbeugung (X-Ray Diffraction, XRD) zeigtenrnsich in allen Proben ähnliche Spektren. Das lässt darauf schließen, dass das pulverisierte Material in allen Probenrndas gleiche ist. Hierbei zeigte sich eine sehr gute Übereinstimmung mit Schoepit und/oder meta-rnSchoepit(UO2)8O2(OH)12(H2O)10, sowie Becquerelite. Weiterhin war weder Autunit, Sabugalit noch Uranylphosphatrnanwesend, was die Ergebnisse einer anderen Studie, durchgeführt an denselben Proben, wiederlegt. DiernAnwesenheit von P, C oder Ca im Probenmaterial konnte ausgeschlossen werden. Im Falle von Calciumkann diesrnmit der Anwesenheit von Uran erklärt werden, welches aufgrund seines Atomradius bevorzugt in Becquerelite (1:6)rneingebaut wird. Die beiden Hauptpeaks für Uran lagen im Falle von U 4f 7/2 bei 382.0 eV und im Falle von U 4f 5/2rnbei 392 eV. Diese Werte mit den Literaturwerten für Schoepit und meta-Schoepitüberein. Die Ergebnissernelektronenmikroskopischen Untersuchung zeigen U, O, Ca, Ti als dominante Komponenten in allen Messungen.rnElemente wie Si, Al, Fe, S, Na, und C wurden ebenfalls detektiert; allerdings kann nicht ausgeschlossen werden,rndass diese Elemente aus dem Boden in der unmittelbaren Umgebung der Munitionsgeschosse stammen. Gold wurdernebenfalls gemessen, was aber auf die Goldarmierung in den Probenaufbereitungsbehältern zurückgeführt werdenrnkann. Die Elektronenmikroskopie zeigte außerdem einige Stellen in denen elementares Uran und Bodenmineralernsowie sekundäre Uranminerale auftraten. Die Elementübersicht zeigt einen direkten Zusammenhang zwischen U andrnCa und gleichzeitig keine Korrelation zwischen U und Si, oder Mg. Auf der anderen Seite zeigte sich aber einrnZusammenhang zwischen Si und Al da beide Konstituenten von Bodenmineralen darstellen. Eine mit Hilfe derrnElektronenstrahlmikroanalyse durchgeführte quantitative Analyse zeigte den Massenanteil von Uran bei ca. 78 - 80%,rnwas mit den 78,2% and 79,47% für Becquerelite beziehungsweise Schoepit aufgrund ihrer Summenformelrnkorrespondiert. Zusätzlich zeigt sich für Calcium ein Massenanteil von 2% was mit dem Wert in Becquerelite (2.19%)rnrecht gut übereinstimmt. Der Massenanteil von Ti lag in einigen Fällen bei 0,77%, was auf eine noch nicht korrodierternDU-Legierung zurückzuführen ist. Ein Lösungsexperiment wurde weiterhin durchgeführt, wobei eine 0,01 M NaClO4-rnLösung zum Einsatz kam in der die verbliebene Probensubstanz der Korrosionsprodukte gelöst wurde;rnNatriumperchlorate wurde hierbei genutzt um die Ionenstärke bei 0,01 zu halten. Um Verunreinigungen durchrnatmosphärisches CO2 zu vermeiden wurden die im Versuch für die drei Hauptproben genutzten 15 Probenbehälterrnmit Stickstoffgas gespült. Eine Modelkalkulation für den beschriebenen Versuchsaufbau wurde mit Visual MINTEQrnv.3.0 für die mittels vorgenannten Analysemethoden beschriebenen Mineralphasen im pH-Bereich von 6 – 10 imrnFalle von Becquerelite, und Schoepit berechnet. Die modellierten Lösungskurven wurden unter An- und Abwesenheitrnvon atmosphärischem CO2 kalkuliert. Nach dem Ende des Lösungsexperiments (Dauer ca. 6 Monate) zeigten diernKonzentrationen des gelösten Urans, gemessen mittels ICP-OES, gute Übereinstimmung mit den modelliertenrnSchoepit und Becquerelite Kurven. Auf Grund des ähnlichen Löslichkeitverhaltens war es nicht möglich zwichen denrnbeiden Mineralen zu unterscheiden. Schoepit kontrolliert im sauren Bereich die Löslichkeit des Urans, währendrnbecquerelit im basichen am wenigsten gelöst wird. Des Weiteren bleibt festzuhalten, dass ein Anteil an CO2 in diernverschlossenen Probenbehälter eingedrungen ist, was sich mit der Vorhersage der Modeldaten deckt. Die Löslichkeitrnvon Uran in der Lösung als Funktion des pH-Wertes zeigte die niedrigsten Konzentrationen im Falle einer Zunahmerndes pH-Wertes von 5 auf 7 (ungefähr 5,1 x 10-6 mol/l) und einer Zunahme des pH-Wertes auf 8 (ungefähr 1,5 x 10-6rnmol/l bei). Oberhalb dieses Bereichs resultiert jeder weitere Anstieg des pH-Wertes in einer Zunahme gelösten Uransrnin der Lösung. Der ph-Wert der Lösung wie auch deren pCO2-Wert kontrollieren hier die Menge des gelösten Urans.rnAuf der anderen Seite zeigten im Falle von Becquerelite die Ca-Konzentrationen höhere Werte als erwartet, wobeirnwahrscheinlich auf eine Vermischung der Proben mit Bodensubstanz zurückgeführt werden kann. Abschließendrnwurde, unter Berücksichtigung der oben genannten Ergebnisse, eine Fallstudie aus Basrah (Irak) diskutiert, wo inrnzwei militärischen Konflikten Uranmunition in zwei Regionen unter verschiedenen Umweltbedingungen eingesetztrnwurden.

An interferon regulatory factor element controls the major immune modulator of murine cytomegalovirus

Immune modulation by herpesviruses, such as cytomegalovirus, is critical for the establishment of acute and persistent infection confronting a vigorous antiviral immune response of the host. Therefore, the action of immune-modulatory proteins has long been the subject of research, with the final goal to identify new strategies for antiviral therapy.rnIn the case of murine cytomegalovirus (mCMV), the viral m152 protein has been identified to play a major role in targeting components of both the innate and the adaptive immune system in terms of infected host-cell recognition in the effector phase of the antiviral immune response. On the one hand, it inhibits cell surface expression of RAE-1 and thereby prevents ligation of the activating natural killer (NK)-cell receptor NKG2D. On the other hand, it decreases cell surface expression of peptide-loaded MHC class I molecules thereby preventing antigen presentation to CD8 T cells. Ultimately, the outcome of CMV infection is determined by the interplay between viral and cellular factors.rnIn this context, the work presented here has revealed a novel and intriguing connection between viral m152 and cellular interferon (IFN), a key cytokine of the immune system: rnthe m152 promoter region contains an interferon regulatory factor element (IRFE) perfectly matching the consensus sequence of cellular IRFEs.rnThe biological relevance of this regulatory element was first suggested by sequence comparisons revealing its evolutionary conservation among various established laboratory strains of mCMV and more recent low-passage wild-derived virus isolates. Moreover, search of the mCMV genome revealed only three IRFE sites in the complete sequence. Importantly, the functionality of the IRFE in the m152 promoter was confirmed with the use of a mutant virus, representing a functional deletion of the IRFE, and its corresponding revertant virus. In particular, m152 gene expression was found to be inhibited in an IRFE-dependent manner in infected cells. Essentially, this inhibition proved to have a severe impact on the immune-modulatory function of m152, first demonstrated by a restored direct antigen presentation on infected cells for CD8 T-cell activation. Even more importantly, this effect of IRFE-mediated IFN signaling was validated in vivo by showing that the protective antiviral capacity of adoptively-transferred, antigen-specific CD8 T cells is also significantly restored by the IRFE-dependent inhibition of m152. Somewhat curious and surprising, the decrease in m152 protein simultaneously prevented an enhanced activation of NK cells in acute-infected mice, apparently independent of the RAE-1/NKG2D ligand/receptor interaction but rather due to reduced ‘missing-self’ recognition.rnTaken together, this work presents a so far unknown mechanism of IFN signaling to control mCMV immune modulation in acute infection.rnrn

Geological and hydrogeological features affecting migration, multi-phase partitioning and degradation of chlorinated hydrocarbons through unconsolidated porous media.

Chlorinated solvents are the most ubiquitous organic contaminants found in groundwater since the last five decades. They generally reach groundwater as Dense Non-Aqueous Phase Liquid (DNAPL). This phase can migrate through aquifers, and also through aquitards, in ways that aqueous contaminants cannot. The complex phase partitioning to which chlorinated solvent DNAPLs can undergo (i.e. to the dissolved, vapor or sorbed phase), as well as their transformations (e.g. degradation), depend on the physico-chemical properties of the contaminants themselves and on features of the hydrogeological system. The main goal of the thesis is to provide new knowledge for the future investigations of sites contaminated by DNAPLs in alluvial settings, proposing innovative investigative approaches and emphasizing some of the key issues and main criticalities of this kind of contaminants in such a setting. To achieve this goal, the hydrogeologic setting below the city of Ferrara (Po plain, northern Italy), which is affected by scattered contamination by chlorinated solvents, has been investigated at different scales (regional and site specific), both from an intrinsic (i.e. groundwater flow systems) and specific (i.e. chlorinated solvent DNAPL behavior) point of view. Detailed investigations were carried out in particular in one selected test-site, known as “Caretti site”, where high-resolution vertical profiling of different kind of data were collected by means of multilevel monitoring systems and other innovative sampling and analytical techniques. This allowed to achieve a deep geological and hydrogeological knowledge of the system and to reconstruct in detail the architecture of contaminants in relationship to the features of the hosting porous medium. The results achieved in this thesis are useful not only at local scale, e.g. employable to interpret the origin of contamination in other sites of the Ferrara area, but also at global scale, in order to address future remediation and protection actions of similar hydrogeologic settings.

Investigation of the reactivity of metal oxide catalysts for the gas-phase phenol methylation

The gas-phase phenol methylation with methanol was investigated both from catalitic and spectroscopic point of view. In particular, the work focus on the behavior of metal oxide catalysts, like iron(III) vanadate and aluminum vanadate. Spectroscopic studies include: X-ray diffraction and Raman analysis for catalyst charactrerization; Diffuse reflectance infrared fourier transform spectroscopy and in-situ Infrared spectroscopy in vacuum for investigation of interactions between reactants and surface of catalysts.

Bone-implant interface. Evaluation of osteoblastic cells behavior on nanopatterned titanium surfaces: an in vitro analysis

Protein-adsorption occurs immediately following implantation of biomaterials. It is unknown at which extent protein-adsorption impacts the cellular events at bone-implant interface. To investigate this question, we compared the in-vitro outcome of osteoblastic cells grown onto titanium substrates and glass as control, by modulating the exposure to serum-derived proteins. Substrates consisted of 1) polished titanium disks; 2) polished disks nanotextured with H2SO4/H2O2; 3) glass. In the pre-adsorption phase, substrates were treated for 1h with αMEM alone (M-noFBS) or supplemented with 10%-foetal-bovine-serum (M-FBS). MC3T3-osteoblastic-cells were cultured on the pre-treated substrates for 3h and 24h, in M-noFBS and M-FBS. Subsequently, the culture medium was replaced with M-FBS and cultures maintained for 3 and 7days. Cell-number was evaluated by: Alamar-Blue and MTT assay. Mitotic- and osteogenic-activities were evaluated through fluorescence-optical-microscope by immunolabeling for Ki-67 nuclear-protein and Osteopontin. Cellular morphology was evaluated by SEM-imaging. Data were statistically analyzed using ANOVA-test, (p<0.05). At day3 and day7, the presence or absence of serum-derived proteins during the pre-adsorption phase had not significant effect on cell-number. Only the absence of FBS during 24h of culture significantly affected cell-number (p<0.0001). Titanium surfaces performed better than glass, (p<0.01). The growth rate of cells between day3 and 7 was not affected by the initial absence of FBS. Immunolabeling for Ki-67 and Osteopontin showed that the mitotic- and osteogenic- activity were ongoing at 72h. SEM-analysis revealed that the absence of FBS had no major influence on cell-shape. • Physico-chemical interactions without mediation by proteins are sufficient to sustain the initial phase of culture and guide osteogenic-cells toward differentiation. • The challenge is avoiding adsorption of ‘undesirables’ molecules that negatively impact on the cueing cells receive from surface. This may not be a problem in healthy patients, but may have an important role in medically-compromised-individuals in whom the composition of tissue-fluids is altered.

57 Fe and 119 Sn Mössbauer studies on new Heusler compounds for spintronic applications

Seit der Entwicklung einer großen Vielfalt von Anwendungsmöglichkeiten der Spintronik auf Basis von Heusler Verbindungen innerhalb der letzten Dekade kann der Forschungsfortschritt an dieser Material Klasse in einer Vielzahl von Publikationen verfolgt werden. Eine typische Heusler Verbindung X2YZ besteht aus zwei Übergangsmetallen (X, Y) und einem Hauptgruppenelement (Z). Diese Arbeit berichtet von Heusler Verbindungen mit besonderem Augenmerk auf deren potentielle halbmetallische Eigenschaften und davon insbesondere solche, die eine richtungsabhängige magnetische Anisotropie (perpendicular magnetic anisotropy- PMA) zeigen könnten. PMA ist insbesondere für Spin transfer Torque (STT) Bauelemente von großem Interesse und tritt in tetragonalrnverzerrten Heusler Verbindungen auf. Bei STT-Elementen werden mittels spinpolarisierter Ströme die magnetische Orientierung von magnetischen Schichten beeinflusst.rnDie signifikantesten Ergebnisse dieser Arbeit sind: die Synthese neuer kubischen Heusler Phasen Fe2YZ, die theoretisch als tetragonal vorausgesagt wurden (Kapitel 1), die Synthese von Mn2FeGa, das in der tetragonal verzerrten Struktur kristallisiert und Potential für STT Anwendungen zeigt (Kapitel 2); die Synthese von Fe2MnGa, das einen magnetischen Phasenübergang mit exchange-bias (EB) Effekt zeigt, der auf einer Koexistenz von ferromagnetischen (FM) und antiferromagnetischen (AFM) Phasen beruht (Kapitel 3); Schlussendlich wird in Kapitel 4 die Synthese von Mn3−xRhxSn diskutiert, in welcher insbesondere tetragonales Mn2RhSn als potentielles Material für Anwendungen in derrnSpintronik vorgestellt wird.rnIn dieser Arbeit wurden hauptsächlich Heusler Verbindungen mit mößbaueraktiven Elementen 57Fe und 119Sn, synthetisiert und untersucht. Im Falle der hier untersuchten Heusler Verbindungen spielt die Charakterisierung durch Mößbauer Spektroskopie eine entscheidende Rolle, da Heusler Verbindungen meistens ein gewisses Maß an Fehlordnung aufweisen, welche deren magnetischen und strukturellen Eigenschaften beeinflussen kann. Die Art der Fehlordnung jedoch kann nur schwer durch standard Pulver-Röntgendiffraktion bestimmt werden, weshalb wir die Vorteile der Mößbauer Spektroskopie als lokale Methode nutzen, um den Typ und den Grad der Fehlordnung aufzuklären. rnDiese Arbeit ist wie folgt gegliedert:rnIn Kapitel 1 wurden die neuen, kubisch-weichferromagnetischen Heuslerphasen Fe2NiGe, Fe2CuGa und Fe2CuAl synthetisiert und charakterisiert. In vorangegangenen theoretischen Studien wurde für deren Existenz in tetragonaler Heuslerstruktur vorhergesagt.rnUngeachtet dessen belegten unsere experimentellen Untersuchungen, dass diese Verbindungen hauptsächlich in der kubischen invers Heusler(X-) struktur mit unterschiedlichen Anteilen an atomarer Fehlordnung kristallisieren. Alle Verbindungen sind weiche Ferromagneten mit hoher Curietemperatur bis zu 900K, weswegen alle als potentielle Materialien für magnetische Anwendungen geeignet sind. In Kapitel 2 wurde Mn2FeGa synthetisiert. Es zeigte sich, dass Mn2FeGa nach Temperatur Nachbehandlung bei 400°C die invers tetragonale Struktur (I4m2) annimmt. Theoretisch wurde die Existenz in der inversen kubischen Heuslerstruktur vorausgesagt. Abhängig von den Synthesebedingungen ändern sich die magnetischen und strukturellen Eigenschaften von Mn2FeGa eklatant. Deshalb ändert sich die Kristallstruktur von M2FeGa bei Temperung bei 800 °C zu einer pseudokubischen Cu3Au-artigen Struktur, in welcher Fe- und Mn-Atome statistisch verteilt vorliegen. Dieser Übergang der Kristallstrukturen wurde durch Mößbauer Spektroskopie anhand des Vorliegens oder Fehlens der Quadrupolaufspaltung im Falle der invers tetragonalen bzw. pseudokubischen Modifikation nachgewiesen. In Kapitel 3 wurde Fe2MnGa ebenfalls erfolgreich synthetisiert und durch verschiedene Methoden charakterisiert. Der Zusammenhang von Kristallstruktur und magnetischen Eigenschaften wurde durch verschiedene Temperungskonditionen und mechanischer Behandlung untersucht. Der Schwerpunkt lag auf einer geschmolzenen Probe ohne weitere Temperung, die einen FM-AFM Phasenübergang zeigte. Diese magnetische Phasenumwandlung führt zu einem starken EB-Verhalten, welches seinen Ursprung hauptsächlich in der Koexistenz von FM- und AFM-Phasen unterhalb der FMAFM- Übergangstemperatur hat. Kapitel 4 ist den neuen Mn-basierten Heusler-Verbindungen Mn3−xRhxSn gewidmet, bei denen wir versuchten, durch den Austausch von Mn durch das größere Rh eine Umwandlung zu einer tetragonalen Struktur von den hexagonalen Mn3Sn-Struktur zu erreichen. Als interessant stellten sich Mn2RhSn und Mn2.1Rh0.9Sn heraus, da sie aus nur einer Phase vorzuliegen scheinen, wohingegen die anderen Verbindungen aus gemischten Phasen mit gleichzeitiger starken Fehlordnung bestehen. Im abschließenden Anhang wurden die Fehlordnung und gelegentliche Mischphasen einer großen Auswahl von Mn3−xFexGa Materialien mit 1≤x≤3, dokumentiert.rn

Structural verification of the ESEO spacecraft: from launch loads analysis to composite panels verification

The present thesis work was performed in the frame of ESEO (European Student Earth Orbiter) project. The activities that are described in this document were carried out in the Microsatellites and Space Micro systems Lab led by Professor Paolo Tortora and in ALMASpace company facilities. The thesis deals with ESEO structural analysis, at system and unit level, and verification: after determining the design limit loads to be applied to the spacecraft as an envelope of different launchers load profiles, a finite element structural analysis was performed on the model of the satellite in order to ensure the capability to withstand the loads encountered during the launch; all the analyses were performed according to ESA standards and using the software MSC NASTRAN SIMXPERT. Amplification factors were derived and used to determine loads to be considered at unit level. In particular structural analyses were carried out on the GPS unit, the payload developed for ESEO by students of University of Bologna and results were used in the preparation of GPS payload design definition file. As for the verification phase a study on the panels and inserts to be used in the spacecraft was performed: different designs were created exploiting methods to optimize weight and mechanical behavior. The configurations have been analyzed and results compared to select the final design.

Crystallization and morphology of the PLLA phase within random poly (L-lactide-ran-ɛ-caprolactone)

This work has mainly focused on the poly (L-lactide) (PLLA) which is a material for multiple applications with performances comparable to those of petrochemical polymers (PP, PS, PET, etc. ...), readily recyclable and also compostable. However, PLLA has certain shortcomings that limit its applications. It is a brittle, hard polymer with a very low elongation at break, hydrophobic, exhibits low crystallization kinetics and takes a long time to degrade. The properties of PLLA may be modified by copolymerization (random, block, and graft) of L-lactide monomers with other co-monomers. In this thesis it has been studied the crystallization and morphology of random copolymers poly (L-lactide-ran-ε-caprolactone) with different compositions of the two monomers since the physical, mechanical, optical and chemical properties of a material depend on this behavior. Thermal analyses were performed by differential scanning calorimetry (DSC) and thermogravimetry (TGA) to observe behaviors due to the different compositions of the copolymers. The crystallization kinetics and morphology of poly (L-lactide-ran-ε-caprolactone) was investigated by polarized light optical microscopy (PLOM) and differential scanning calorimetry (DSC). Their thermal behavior was observed with crystallization from melt. It was observed that with increasing amounts of PCL in the copolymer, there is a decrease of the thermal degradation. Studies on the crystallization kinetics have shown that small quantities of PCL in the copolymer increase the overall crystallization kinetics and the crystal growth rate which decreases with higher quantities of PCL.

Thermoelectric properties in phase-separated half-Heusler materials

The conversion of dissipated heat into electricity is the basic principle of thermoelectricity. In this context, half-Heusler (HH) compounds are promising thermoelectric (TE) materials for waste heat recovery. They meet all the requirements for commercial TE applications, ranging from good efficiencies via environmentally friendliness to being low cost materials. This work focused on the TE properties of Ti0.3Zr0.35Hf0.35NiSn-based HH materials. This compound undergoes an intrinsic phase separation into a Ti-poor and Ti-rich HH phase during a rapid solidification process. The resulting dendritic microstructure causes a drastic reduction of the thermal conductivity, leading to higher TE efficiencies in these materials. The TE properties and temperature dependence of the phase-separated Ti0.3Zr0.35Hf0.35NiSn compound were investigated. The TE properties can be adjusted depending on the annealing treatment. The extension of annealing time for 21 days at 1000 °C revealed a reduction of the thermal conductivity and thus an enhancement of the TE performance in this sample. An increase of annealing temperature caused a change of the phase fraction ratio in favor of the Ti-rich phase, leading to an improvement of the electronic properties. rnInspired by the TE properties of the Ti0.3Zr0.35Hf0.35NiSn HH compound, the performance of different n- and p-type materials, realized via site substitution with donor and acceptor elements was examined. The fabrication of a TE n- and p-type material pair based on one starting compound can guarantee similar TE and mechanical properties and is enormous beneficial for device engineering. As donor dopants V, Nb and Sb were tested. Depending on the lattice position small doping levels were sufficient to attain distinct improvement in their TE efficiency. Acceptor-induced doping with Sc, Y and Co caused a change in the transport behavior from n- to p- type conduction, revealing the highest Seebeck coefficients obtained in the MNiSn system. rnThen, the long-term stability of an exemplary n- and p-type HH compound was proven. Surprisingly, the dendritic microstructure can be maintained even after 500 cycles (1700 h) from 373 to 873 K. The TE performance of both n- and p-type materials showed no significant change under the long-term treatment, indicating the extraordinary temperature stability of these compounds. Furthermore both HH materials revealed similar temperature-dependence of their mechanical properties. This work demonstrates the excellent suitability of phase-separated HH materials for future TE applications in the moderate temperature range.rn

Planetary Gear Modal Vibration Experiments and Correlation against Lumped-Parameter and Finite Element Models

Experimental modal analysis techniques are applied to characterize the planar dynamic behavior of two spur planetary gears. Rotational and translational vibrations of the sun gear, carrier, and planet gears are measured. Experimentally obtained natural frequencies, mode shapes, and dynamic response are compared to the results from lumped-parameter and finite element models. Two qualitatively different classes of mode shapes in distinct frequency ranges are observed in the experiments and confirmed by the lumped-parameter model, which considers the accessory shafts and fixtures in the system to capture all of the natural frequencies and modes. The finite element model estimates the high-frequency modes that have significant tooth mesh deflection without considering the shafts and fixtures. The lumped-parameter and finite element models accurately predict the natural frequencies and modal properties established by experimentation. Rotational, translational, and planet mode types presented in published mathematical studies are confirmed experimentally. The number and types of modes in the low-frequency and high-frequency bands depend on the degrees of freedom in the central members and planet gears, respectively. The accuracy of natural frequency prediction is improved when the planet bearings have differing stiffnesses in the tangential and radial directions, consistent with the bearing load direction. (C) 2012 Elsevier Ltd. All rights reserved.

Adsorption behavior of redox-active suppressor additives: Combined electrochemical and STM studies

The redox chemistry and the related surface phase behavior of Safranine (SAF) and Janus Green B (JGB) have been studied by means of cyclic voltammetry in combination with in situ Scanning Tunneling Microscopy using HOPG (Highly Oriented Pyrolytic Graphite) and single crystalline Cu(1 0 0) as model substrates, both revealing different widths of the accessible potential windows. JGB and SAF serve as prototypical heterocyclic suppressor/leveler additives that are used for the metallization of 3D-TSVs (3D Through Silicon Vias) following a classical "leveling" concept. SAF can be considered as the reductive decomposition product of JGB that is formed at the copper/electrolyte interface upon electroplating. Both additives reveal a pronounced pH-dependent redox-chemistry with redox-transitions lying close to or even beyond the anodic limit of the copper potential window. Affected by these redox-processes are in particular the aromatic cores of those heterocycles that can be (quasi)reversibly reduced by a two electron transfer process within the potential window of copper. Therefore we identify the reduced form of those dyes as the active components for the suppressing/leveling effect in copper plating. STM data clearly shows a dye surface phase behavior that is crucially determined by its potential-dependent redox-chemistry. This will be exemplarily discussed for the SAF dye. On chloride-modified Cu(1 0 0) mono-reduced SAF forms a structurally well-defined monolayer of cationic stacking polymers. However, this coupled anion/cation layer reveals only minor suppressing capabilities with respect to the copper dissolution and deposition processes. Complete reduction of the aromatic heterocycle finally leads to the 3D precipitation of hydrophobic reaction products. 3D clusters of this SAF precipitate are discussed as the active structural motif for the suppressing effect of these dyes. (C) 2011 Elsevier Ltd. All rights reserved.

Analyzing the effects of vertical acceleration and deceleration in multi-phase, debris-flow sediment-column experiments / by Christine Marie Williams.

Water-saturated debris flows are among some of the most destructive mass movements. Their complex nature presents a challenge for quantitative description and modeling. In order to improve understanding of the dynamics of these flows, it is important to seek a simplified dynamic system underlying their behavior. Models currently in use to describe the motion of debris flows employ depth-averaged equations of motion, typically assuming negligible effects from vertical acceleration. However, in many cases debris flows experience significant vertical acceleration as they move across irregular surfaces, and it has been proposed that friction associated with vertical forces and liquefaction merit inclusion in any comprehensive mechanical model. The intent of this work is to determine the effect of vertical acceleration through a series of laboratory experiments designed to simulate debris flows, testing a recent model for debris flows experimentally. In the experiments, a mass of water-saturated sediment is released suddenly from a holding container, and parameters including rate of collapse, pore-fluid pressure, and bed load are monitored. Experiments are simplified to axial geometry so that variables act solely in the vertical dimension. Steady state equations to infer motion of the moving sediment mass are not sufficient to model accurately the independent solid and fluid constituents in these experiments. The model developed in this work more accurately predicts the bed-normal stress of a saturated sediment mass in motion and illustrates the importance of acceleration and deceleration.

Three dimensional finite element simulation of polymer melting and flow in a single-screw extruder : optimization of screw channel geometry

Single-screw extrusion is one of the widely used processing methods in plastics industry, which was the third largest manufacturing industry in the United States in 2007 [5]. In order to optimize the single-screw extrusion process, tremendous efforts have been devoted for development of accurate models in the last fifty years, especially for polymer melting in screw extruders. This has led to a good qualitative understanding of the melting process; however, quantitative predictions of melting from various models often have a large error in comparison to the experimental data. Thus, even nowadays, process parameters and the geometry of the extruder channel for the single-screw extrusion are determined by trial and error. Since new polymers are developed frequently, finding the optimum parameters to extrude these polymers by trial and error is costly and time consuming. In order to reduce the time and experimental work required for optimizing the process parameters and the geometry of the extruder channel for a given polymer, the main goal of this research was to perform a coordinated experimental and numerical investigation of melting in screw extrusion. In this work, a full three-dimensional finite element simulation of the two-phase flow in the melting and metering zones of a single-screw extruder was performed by solving the conservation equations for mass, momentum, and energy. The only attempt for such a three-dimensional simulation of melting in screw extruder was more than twenty years back. However, that work had only a limited success because of the capability of computers and mathematical algorithms available at that time. The dramatic improvement of computational power and mathematical knowledge now make it possible to run full 3-D simulations of two-phase flow in single-screw extruders on a desktop PC. In order to verify the numerical predictions from the full 3-D simulations of two-phase flow in single-screw extruders, a detailed experimental study was performed. This experimental study included Maddock screw-freezing experiments, Screw Simulator experiments and material characterization experiments. Maddock screw-freezing experiments were performed in order to visualize the melting profile along the single-screw extruder channel with different screw geometry configurations. These melting profiles were compared with the simulation results. Screw Simulator experiments were performed to collect the shear stress and melting flux data for various polymers. Cone and plate viscometer experiments were performed to obtain the shear viscosity data which is needed in the simulations. An optimization code was developed to optimize two screw geometry parameters, namely, screw lead (pitch) and depth in the metering section of a single-screw extruder, such that the output rate of the extruder was maximized without exceeding the maximum temperature value specified at the exit of the extruder. This optimization code used a mesh partitioning technique in order to obtain the flow domain. The simulations in this flow domain was performed using the code developed to simulate the two-phase flow in single-screw extruders.

Discrete element methods for asphalt concrete : development and application of user-defined microstructural models and a viscoelastic micromechanical model

As an important Civil Engineering material, asphalt concrete (AC) is commonly used to build road surfaces, airports, and parking lots. With traditional laboratory tests and theoretical equations, it is a challenge to fully understand such a random composite material. Based on the discrete element method (DEM), this research seeks to develop and implement computer models as research approaches for improving understandings of AC microstructure-based mechanics. In this research, three categories of approaches were developed or employed to simulate microstructures of AC materials, namely the randomly-generated models, the idealized models, and image-based models. The image-based models were recommended for accurately predicting AC performance, while the other models were recommended as research tools to obtain deep insight into the AC microstructure-based mechanics. A viscoelastic micromechanical model was developed to capture viscoelastic interactions within the AC microstructure. Four types of constitutive models were built to address the four categories of interactions within an AC specimen. Each of the constitutive models consists of three parts which represent three different interaction behaviors: a stiffness model (force-displace relation), a bonding model (shear and tensile strengths), and a slip model (frictional property). Three techniques were developed to reduce the computational time for AC viscoelastic simulations. It was found that the computational time was significantly reduced to days or hours from years or months for typical three-dimensional models. Dynamic modulus and creep stiffness tests were simulated and methodologies were developed to determine the viscoelastic parameters. It was found that the DE models could successfully predict dynamic modulus, phase angles, and creep stiffness in a wide range of frequencies, temperatures, and time spans. Mineral aggregate morphology characteristics (sphericity, orientation, and angularity) were studied to investigate their impacts on AC creep stiffness. It was found that aggregate characteristics significantly impact creep stiffness. Pavement responses and pavement-vehicle interactions were investigated by simulating pavement sections under a rolling wheel. It was found that wheel acceleration, steadily moving, and deceleration significantly impact contact forces. Additionally, summary and recommendations were provided in the last chapter and part of computer programming codes wree provided in the appendixes.

Modeling mechanical response of heterogeneous materials

Heterogeneous materials are ubiquitous in nature and as synthetic materials. These materials provide unique combination of desirable mechanical properties emerging from its heterogeneities at different length scales. Future structural and technological applications will require the development of advanced light weight materials with superior strength and toughness. Cost effective design of the advanced high performance synthetic materials by tailoring their microstructure is the challenge facing the materials design community. Prior knowledge of structure-property relationships for these materials is imperative for optimal design. Thus, understanding such relationships for heterogeneous materials is of primary interest. Furthermore, computational burden is becoming critical concern in several areas of heterogeneous materials design. Therefore, computationally efficient and accurate predictive tools are highly essential. In the present study, we mainly focus on mechanical behavior of soft cellular materials and tough biological material such as mussel byssus thread. Cellular materials exhibit microstructural heterogeneity by interconnected network of same material phase. However, mussel byssus thread comprises of two distinct material phases. A robust numerical framework is developed to investigate the micromechanisms behind the macroscopic response of both of these materials. Using this framework, effect of microstuctural parameters has been addressed on the stress state of cellular specimens during split Hopkinson pressure bar test. A voronoi tessellation based algorithm has been developed to simulate the cellular microstructure. Micromechanisms (microinertia, microbuckling and microbending) governing macroscopic behavior of cellular solids are investigated thoroughly with respect to various microstructural and loading parameters. To understand the origin of high toughness of mussel byssus thread, a Genetic Algorithm (GA) based optimization framework has been developed. It is found that two different material phases (collagens) of mussel byssus thread are optimally distributed along the thread. These applications demonstrate that the presence of heterogeneity in the system demands high computational resources for simulation and modeling. Thus, Higher Dimensional Model Representation (HDMR) based surrogate modeling concept has been proposed to reduce computational complexity. The applicability of such methodology has been demonstrated in failure envelope construction and in multiscale finite element techniques. It is observed that surrogate based model can capture the behavior of complex material systems with sufficient accuracy. The computational algorithms presented in this thesis will further pave the way for accurate prediction of macroscopic deformation behavior of various class of advanced materials from their measurable microstructural features at a reasonable computational cost.