Broadband infrared luminescence from transparent glass-ceramics containing Ni2+-doped beta-Ga2O3 nanocrystals

Transparent Ni2+-doped beta-Ga2O3 glass-ceramics were synthesized. The nanocrystal phase in the glass-ceramics was identified to be beta-Ga2O3 and its size was about 3.6 nm. It was confirmed from the absorption spectra that the ligand environment of Ni2+ ions changed from the trigonal bi-pyramid fivefold sites in the as-cast glass to the octahedral sites in the glass-ceramics. The broadband infrared emission centering at 1270 nm with full width at half maximum (FWHM) of more than 250 nm was observed. The fluorescence lifetime was about 1.1 mu s at room temperature. The observed infrared emission could be attributed to the T-3 (2g) (F-3) -> (3)A (2g) (F-3) transition of octahedral Ni2+ ions. It is suggested that the Ni2+-doped transparent beta-Ga2O3 glass-ceramics with broad bandwidth and long lifetime have a potential as a broadband amplification medium.

Precipitation of nanocrystals in glasses by electron irradiation: An alternative path to form glass ceramics?

This letter demonstrates an alternative method to form gallium silicate glass ceramics using high-energy electron irradiation. Compared with glass ceramics obtained from the conventional thermal treatment method, the distribution and crystal sizes of the precipitated Ga2O3 nanoparticles are the same. An advantage of this method is that the spatial distribution of the precipitated nanoparticles can be easily controlled. However, optically active dopants Ni2+ ions do not participate in the precipitation during electron irradiation. (c) 2007 American Institute of Physics.

Iridium and rhodium analogues of the Shilov cycle catalyst; and the investigation and applications of the Reduction-Coupled Oxo Activation (ROA) mechanistic motif towards alkane upgrading

This dissertation will cover several disparate topics, with the overarching theme centering on the investigation of organometallic C-H activation and hydrocarbon transformation and upgrading. Chapters 2 and 3 discuss iridium and rhodium analogues of the Shilov cycle catalyst for methane to methanol oxidation, and Chapter 4 on the recently discovered ROA mechanistic motif in catalysts for various alkane partial oxidation reactions. In addition, Chapter 5 discusses the mechanism of nickel pyridine bisoxazoline Negishi catalysts for asymmetric and stereoconvergent C-C coupling, and the appendices discuss smaller projects on rhodium H/D exchange catalysts and DFT method benchmarking.

Chelation-enforced metal-arene interactions : insights into substrate binding and catalysis by late transition metal complexes

Understanding and catalyzing chemical reactions requiring multiple electron transfers is an endeavor relevant to many outstanding challenges in the field of chemistry. To study multi-electron reactions, a terphenyl diphosphine framework was designed to support one or more metals in multiple redox states via stabilizing interactions with the central arene of the terphenyl backbone. A variety of unusual compounds and reactions and their relevance toward prominent research efforts in chemistry are the subject of this dissertation.

Chapter 2 introduces the para-terphenyl diphosphine framework and its coordination chemistry with group 10 transition metal centers. Both mononuclear and dinuclear compounds are characterized. In many cases, the metal center(s) are stabilized by the terphenyl central arene. These metal–arene interactions are characterized both statically, in the solid state, and fluxionally, in solution. As a proof-of-principle, a dinickel framework is shown to span multiple redox states, showing that multielectron chemistry can be supported by the coordinatively flexible terphenyl diphosphine.

Chapter 3 presents reactivity of the terphenyl diphosphine when bound to a metal center. Because of the dearomatizing effect of the metal center, the central arene of the ligand is susceptible to reactions that do not normally affect arenes. In particular, Ni-to-arene H-transfer and arene dihydrogenation reactions are presented. Additionally, evidence for reversibility of the Ni-to-arene H-transfer is discussed.

Chapter 4 expands beyond the chelated metal-arene interactions of the previous chapters. A dipalladium(I) terphenyl diphosphine framework is used to bind a variety of exogenous organic ligands including arenes, dienes, heteroarenes, thioethers, and anionic ligands. The compounds are structurally characterized, and many ligands exhibit unprecedented bindng modes across two metal centers. The relative binding affinities are evaluated spectroscopically, and equilibrium binding constants for the examined ligands are determined to span over 13 orders of magnitude. As an application of this framework, mild hydrogenation conditions of bound thiophene are presented.

Chapter 5 studies nickel-mediated C–O bond cleavage of aryl alkyl ethers, a transformation with emerging applications in fields such as lignin biofuels and organic methodology. Other group members have shown the mechanism of C–O bond cleavage of an aryl methyl ether incorporated into a meta-terphenyl diphosphine framework to proceed through β-H elimination of an alkoxide. First, the electronic selectivity of the model system is examined computationally and compared with catalytic systems. The lessons learned from the model system are then applied to isotopic labeling studies for catalytic aryl alkyl ether cleavage under dihydrogen. Results from selective deuteration experiments and mass spectrometry draw a clear analogy between the mechanisms of the model and catalytic systems that does not require dihydrogen for C–O bond cleavage, although dihydrogen is proposed to play a role in catalyst activation and catalytic turnover.

Appendix A presents initial efforts toward heterodinuclear complexes as models for CO dehydrogenase and Fischer Tropsch chemistry. A catechol-incorporating terphenyl diphosphine is reported, and metal complexes thereof are discussed.

Appendix B highlights some structurally characterized terphenyl diphosphine complexes that either do not thematically belong in the research chapters or proved to be difficult to reproduce. These compounds show unusual coordination modes of the terphenyl diphosphine from which other researchers may glean insights.

Conduction-electron localized-moment interaction in palladium-silicon base amorphous alloys containing transition metals

The electrical and magnetic properties of amorphous alloys obtained by rapid quenching from the liquid state have been studied. The composition of these alloys corresponds to the general formula M_xPd_80-xSi₂₀, in which M stands for a metal of the first transition series between chromium and nickel and x is its atomic concentration. The concentration ranges within which an amorphous structure could be obtained were: from 0 to 7 for Cr, Mn and Fe, from 0 to 11 for Co and from 0 to 15 for Ni. A well-defined minimum in the resistivity vs temperature curve was observed for all alloys except those containing nickel. The alloys for which a resistivity minimum was observed had a negative magnetoresistivity approximately proportional to the square of the magnetization and their susceptibility obeyed the Curie-Weiss law in a wide temperature range. For concentrated Fe and Co alloys the resistivity minimum was found to coexist with ferromagnetism. These observations lead to the conclusion that the present results are due to a s-d exchange interaction. The unusually high resistivity minimum temperature observed in the Cr alloys is interpreted as a result of a high Kondo temperature and a large s-d exchange integral. A low Fermi energy of the amorphous alloys (3.5 eV) is also responsible for the anomalies due to the s-d exchange interaction.

Silicide formation and the interaction of metals with polycrystalline Si

The main factors affecting solid-phase Si-metal interactions are reported in this work. The influence of the orientation of the Si substrates and the presence of impurities in metal films and at the Si-metal interface on the formation of nickel and chromium silicides have been demonstrated. We have observed that the formation and kinetic rate of growth of nickel silicides is strongly dependent on the orientation and crystallinity of the Si substrates; a fact which, up to date, has never been seriously investigated in silicide formation. Impurity contaminations in the Cr film and at the Si-Cr interface are the most dominant influencing factors in the formation and kinetic rate of growth of CrSi₂. The potentiality and use of silicides as a diffusion barrier in metallization on silicon devices were also investigated.

Two phases, Ni₂Si and NiSi, form simultaneously in two distinct sublayers in the reaction of Ni with amorphous Si, while only the former phase was observed on other substrates. On (111) oriented Si substrates the growth rate is about 2 to 3 times less than that on <100> or polycrystalline Si. Transmission electron micrographs establish-·that silicide layers grown on different substrates have different microcrystalline structures. The concept of grain-boundary diffusion is speculated to be an important factor in silicide formation.

The composition and kinetic rate of CrSi₂ formation are not influenced by the underlying Si substrate. While the orientation of the Si substrate does not affect the formation of CrSi₂ , the purity of the Cr film and the state of Si-Cr interface become the predominant factors in the reaction process. With an interposed layer of Pd₂Si between the Cr film and the Si substrate, CrSi₂ starts to form at a much lower temperature (400°C) relative to the Si-Cr system. However, the growth rate of CrSi₂ is observed to be independent of the thickness of the Pd2Si layer. For both Si-Cr and Si-Pd₂Si-Cr samples, the growth rate is linear with time with an activation energy of 1.7 ± 0.1 ev.

A tracer technique using radioactive ³¹Si (T_1/2 = 2.26 h) was used to study the formation of CrSi₂ on Pd₂Si. It is established from this experiment that the growth of CrSi₂ takes place partly by transport of Si directly from the Si substrate and partly by breaking Pd₂Si bonds, making free Si atoms available for the growth process.

The role of CrSi₂ in Pd-Al metallization on Si was studied. It is established that a thin CrSi₂ layer can be used as a diffusion barrier to prevent Al from interacting with Pd₂Si in the Pd-Al metallization on Si.

As a generalization of what has been observed for polycrystalline-Si-Al interaction, the reactions between polycrystalline Si (poly Si) and other metals were studied. The metals investigated include Ni, Cr, Pd, Ag and Au. For Ni, Cr and Pd, annealing results in silicide formation, at temperatures similar to those observed on single crystal Si substrates. For Al, Ag and Au, which form simple eutectics with Si annealing results in erosion of the poly Si layer and growth of Si crystallites in the metal films.

Backscattering spectrometry with 2.0 and 2.3 MeV ⁴He ions was the main analytical tool used in all our investigations. Other experimental techniques include the Read camera glancing angle x-ray diffraction, scanning electron, optical and transmission electron microscopy. Details of these analytical techniques are given in Chapter II.

Heavy metal pollution in sediments at shipbreaking area of Bangladesh

The research was carried out to assess the trace metal concentration in sediments of ship breaking area in Bangladesh. The study areas were separated into Ship breaking Zone and Reference Site for comparative analysis. Metals like Iron ( Fe) was found at 11932 to 41361.71µg.g-1 in the affected site and 3393.37 µg.g-1 in the control site. Manganese (Mn) varied from 2.32 to 8.25 µg.g-1 in the affected site where as it was recorded as 1.8 µg.g-1 in the control area. Chromium(Cr), Nickel (Ni), Zinc(Zn) and Lead (Pb) were also varied from 22.89 to 86.72 µg.g-1; 23.12 to 48.6;83.78 to 142.85 and 36.78 to 147.83 µg.g-1 respectively in the affected site whereas these were recorded as 19; 3.98; 22.22 and 8.82 µg.g-1 in the control site. Copper (Cu); Cadmium (Cd) and Mercury (Hg) concentration were varied from 21.05 to 39.85; 0.57 to 0.94 and 0.05 to 0.11 µg.g-1 in the affected site and 33.0; 0.115 and 0.01 µg.g-1 in the control site. It may conclude that heavy metal pollution in sediments at ship breaking area of Bangladesh is at alarming stage.

I. Reactively sputtered Ti-Si-N thin films for diffusion barrier applications. II. Oxidation, diffusion and crystallization of an amorphous Zr_(60)Al_(15)Ni_(25) alloy.

Films of Ti-Si-N obtained by reactively sputtering a TiSi_2, a Ti_5Si_3, or a Ti_3Si target are either amorphous or nanocrystalline in structure. The atomic density of some films exceeds 10^23 at./cm^3. The room-temperature resistivity of the films increases with the Si and the N content. A thermal treatment in vacuum at 700 °C for 1 hour decreases the resistivity of the Ti-rich films deposited from the Ti_5Si_3 or the Ti_3Si target, but increases that of the Si-rich films deposited from the TiSi_2 target when the nitrogen content exceeds about 30 at. %.

Ti_(34)Si_(23)N_(43) deposited from the Ti_5Si_3 target is an excellent diffusion barrier between Si and Cu. This film is a mixture of nanocrystalline TiN and amorphous SiN_x. Resistivity measurement from 80 K to 1073 K reveals that this film is electrically semiconductor-like as-deposited, and that it becomes metal-like after an hour annealing at 1000 °C in vacuum. A film of about 100 nm thick, with a resistivity of 660 µΩcm, maintains the stability of Si n+p shallow junction diodes with a 400 nm Cu overlayer up to 850 °C upon 30 min vacuum annealing. When used between Si and Al, the maximum temperature of stability is 550 °C for 30 min. This film can be etched in a CF_4/O_2 plasma.

The amorphous ternary metallic alloy Zr_(60)Al_(15)Ni_(25) was oxidized in dry oxygen in the temperature range 310 °C to 410 °C. Rutherford backscattering and cross-sectional transmission electron microscopy studies suggest that during this treatment an amorphous layer of zirconium-aluminum-oxide is formed at the surface. Nickel is depleted from the oxide and enriched in the amorphous alloy below the oxide/alloy interface. The oxide layer thickness grows parabolically with the annealing duration, with a transport constant of 2.8x10^(-5) m^2/s x exp(-1.7 eV/kT). The oxidation rate is most likely controlled by the Ni diffusion in the amorphous alloy.

At later stages of the oxidation process, precipitates of nanocrystalline ZrO_2 appear in the oxide near the interface. Finally, two intermetallic phases nucleate and grow simultaneously in the alloy, one at the interface and one within the alloy.

A Cerenkov-ΔΕ-Cerenkov detector for high energy cosmic ray isotopes and an accelerator study of ^(40)Ar & ^(56)Fe fragmentation

This thesis has two major parts. The first part of the thesis will describe a high energy cosmic ray detector -- the High Energy Isotope Spectrometer Telescope (HEIST). HEIST is a large area (0.25 m²sr) balloon-borne isotope spectrometer designed to make high-resolution measurements of isotopes in the element range from neon to nickel (10 ≤ Z ≤ 28) at energies of about 2 GeV/nucleon. The instrument consists of a stack of 12 NaI(Tl) scintilla tors, two Cerenkov counters, and two plastic scintillators. Each of the 2-cm thick NaI disks is viewed by six 1.5-inch photomultipliers whose combined outputs measure the energy deposition in that layer. In addition, the six outputs from each disk are compared to determine the position at which incident nuclei traverse each layer to an accuracy of ~2 mm. The Cerenkov counters, which measure particle velocity, are each viewed by twelve 5-inch photomultipliers using light integration boxes.

HEIST-2 determines the mass of individual nuclei by measuring both the change in the Lorentz factor (Δγ) that results from traversing the NaI stack, and the energy loss (ΔΕ) in the stack. Since the total energy of an isotope is given by Ε = γM, the mass M can be determined by M = ΔΕ/Δγ. The instrument is designed to achieve a typical mass resolution of 0.2 amu.

The second part of this thesis presents an experimental measurement of the isotopic composition of the fragments from the breakup of high energy ⁴⁰Ar and ⁵⁶Fe nuclei. Cosmic ray composition studies rely heavily on semi-empirical estimates of the cross-sections for the nuclear fragmentation reactions which alter the composition during propagation through the interstellar medium. Experimentally measured yields of isotopes from the fragmentation of ⁴⁰Ar and ⁵⁶Fe are compared with calculated yields based on semi-empirical cross-section formulae. There are two sets of measurements. The first set of measurements, made at the Lawrence Berkeley Laboratory Bevalac using a beam of 287 MeV/nucleon ⁴⁰Ar incident on a CH₂ target, achieves excellent mass resolution (σ_m ≤ 0.2 amu) for isotopes of Mg through K using a Si(Li) detector telescope. The second set of measurements, also made at the Lawrence Berkeley Laboratory Bevalac, using a beam of 583 MeV/nucleon ⁵⁶FeFe incident on a CH₂ target, resolved Cr, Mn, and Fe fragments with a typical mass resolution of ~ 0.25 amu, through the use of the Heavy Isotope Spectrometer Telescope (HIST) which was later carried into space on ISEE-3 in 1978. The general agreement between calculation and experiment is good, but some significant differences are reported here.

Homo- and Heteronuclear Transition Metal Complexes Supported by Multinucleating Ligands

This dissertation is mainly divided into two sub-parts: organometallic and bioinorganic/materials projects. The approach for the projects involves the use of two different multinucleating ligands to synthesize mono- and multinuclear complexes. Chapter 2 describes the synthesis of a multinucleating tris(phosphinoaryl)benzene ligand used to support mono-nickel and palladium complexes. The isolated mononuclear complexes were observed to undergo intramolecular arene C¬–H to C–P functionalization. The transformation was studied by nuclear magnetic resonance spectroscopy and X-ray crystallography, and represents a rare type of C–H functionalization mechanism, facilitated by the interactions of the group 10 metal with the arene π–system.

Chapter 3 describes the construction of multinickel complexes supported by the same triphosphine ligand from Chapter 2. This chapter shows how the central arene in the ligand’s triarylbenzene framework can interact with dinickel and trinickel moieties in various binding modes. X-ray diffraction studies indicated that all compounds display strong metal–arene interactions. A cofacial triangulo nickel(0) complex supported by this ligand scaffold was also isolated and characterized. This chapter demonstrates the use of an arene as versatile ligand design element for small molecular clusters.

Chapter 4 presents the syntheses of a series of discrete mixed transition metal Mn oxido clusters and their characterization. The synthesis of these oxide clusters displaying two types of transition metals were targeted for systematic metal composition-property studies relevant to mixed transition metal oxides employed in electrocatalysis. A series of heterometallic trimanganese tetraoxido cubanes capped with a redox-active metal [MMn₃O₄] (M = Fe, Co, Ni, Cu) was synthesized starting from a [CaMn₃O₄] precursor and structurally characterized by X-ray crystallography and anomalous diffraction to conclusively determine that M is incorporated at a single position in the cluster. The electrochemical properties of these complexes were studied via cyclic voltammetry. The redox chemistry of the series of complexes was investigated by the addition of a reductant and oxidant. X-ray absorption and electron paramagnetic resonance spectroscopies were also employed to evaluate the product of the oxidation/reduction reaction to determine the site of electron transfer given the presence of two types of redox-active metals. Additional studies on oxygen atom transfer reactivities of [MMn₃O₄] and [MMn₃O₂] series were performed to investigate the effect of the heterometal M in the reaction rates.

Chapter 5 focuses on the use of [CoMn₃O₄] and [NiMn₃O₄] cubane complexes discussed in Chapter 4 as precursors to heterogeneous oxygen evolution reaction (OER) electrocatalysts. These well-defined complexes were dropcasted on electrodes with/without heat treatment, and the OER activities of the resulting films were evaluated. Multiple spectroscopic techniques were performed on the surface of the electrocatalysts to gain insight into the structure-function relationships based on the heterometallic composition. Depending on film preparation, the Co-Mn-oxide was found to change metal composition during catalysis, while the Ni-Mn oxide maintained the NiMn3 ratio. These studies represent the use of discrete heterometallic-oxide clusters as precursors for heterogeneous water oxidation catalysts.

Appendix A describes the ongoing effort to synthesize a series of heteromultimetallic [MMn₃X] clusters (X = O, S, F). Complexes such as [ZnMn₃O], [CoMn₃O], [Mn₃S], and [Mn₄F] have been synthesized and structurally characterized. An amino-bis-oxime ligand (PRABO) has been installed on the [ZnMn₃O] cluster. Upon the addition of O₂, the desymmetrized [ZnMn₃O] cluster only underwent an outer-sphere, one-electron oxidation. Efforts to build and manipulate other heterometallic [MMn₃X] clusters are still ongoing, targeting O₂ binding and reduction. Appendix B summarizes the multiple synthetic approaches to build a [Co₄O₄]-cubane complex relevant to heterogeneous OER electrocatalysis. Starting with the tricobalt cluster [LCo₃(O₂CR)₃] and treatment various strong oxidants that can serve as oxygen atom source in the presence Co²⁺ salt only yielded tricobalt mono–oxo complexes. Appendix C presents the efforts to model the H-cluster framework of [FeFe]-hydrogenase by incorporating a synthetic diiron complex onto a protein-supported or a synthetic ligand-supported [Fe₄S₄]-cluster. The mutant ferredoxin with a [Fe₄S₄]-cluster and triscarbene ligand have been characterized by multiple spectroscopic techniques. The reconstruction of an H-cluster mimic has not yet been achieved, due to the difficulty of obtaining crystallographic evidence and the ambiguity of the EPR results.

Remoção de metais pesados de efluentes sintéticos aquosos por nanofiltração

O objetivo deste trabalho foi estudar a remoção de metais pesados de efluentes sintéticos aquosos através de nanofiltração, com utilização de membrana de poliamida. A membrana utilizada constituída de poliamida apresentou uma boa permeabilidade hidráulica, constatada pela linearidade de fluxo com a variação de pressão de trabalho. Os metais estudados foram cobre, cádmio, zinco, chumbo e níquel com especiação de nitrato e sulfato. O desempenho do sistema foi verificado pela variação dos parâmetros operacionais (pressão e fluxo), associados também com a variação da salinidade e da concentração do metal. Em uma etapa inicial estudou-se a remoção de metais (nitrato e sulfato) isoladamente em uma mesma concentração molar, na pressão de 10 bar, comparando-se as rejeições com e sem agente complexante (EDTA). Em uma segunda etapa, estudou-se o desempenho da membrana, com misturas dos metais (nitrato) e mistura de metais (sulfato), também com e sem agente complexante, os resultados mostraram que a presença de agente complexante melhorou a rejeição dos metais. Nestas misturas estudaram-se os efeitos das concentrações (0,001; 0,0005 e 0,0001mol/L) e das pressões (5; 7; 10 e 12,5 bar) no sistema de remoção, constatou-se que o aumento da concentração e diminuição da pressão afeta a remoção. Em uma terceira etapa, estudou-se a influência da salinidade pela mistura de dois metais de mesma especiação (sulfato), comparando a remoção na pressão de 10 bar. Os resultados atestaram uma rejeição maior que 94 % para todos metais, na pressão de 10 bar, indicando um excelente desempenho e fluxo adequado, daí viabilidade de processo para todas as concentrações testadas. A pertinência do teste se justifica pela adequação do permeado ao atendimento aos padrões ambientais de concentração de metais e confirmam a eficácia do sistema de nanofiltração na remoção de metais pesados

Determinação do potencial tóxico de cobre e níquel e seus complexos com EDTA frente à Daphnia similis

Quando se trata de efluentes muito complexos e de amostras de água ou de sedimento de locais poluídos, é inviável ou até mesmo impossível detectar a presença de todas as substâncias presentes. Os principais contaminantes associados à poluição das águas naturais, tem-se os metais pesados, uma classe de compostos de toxicidade elevada e que são bioacumulados nos seres vivos. Desses metais, o cobre e o níquel se destacam, tanto por seu amplo uso em processos industriais, o que acarreta sua presença em diversos tipos de despejos, quanto por sua toxicidade elevada. O objetivo deste trabalho foi determinar o potencial tóxico do sulfato de cobre e sulfato de níquel, de sua mistura e seus complexos com EDTA frente a Daphnia similis para utilização na avaliação do desempenho do processo de separação com membranas no tratamento de efluentes. Em um estudo de toxicidade, as interações do metal com o organismo-teste são influenciadas pela espécie testada, pela combinação dos metais ou pela composição do meio aquoso. O íon Cu2+ apresentou toxicidade superior ao Ni2+, sendo que na mistura desses dois íons, prevaleceu o resultado obtido para o Cu2+, decorrente de sua maior toxicidade. A complexação dos metais reduz significativamente o potencial tóxico dos metais

Caracterização ambiental da bacia hidrogáfica do Rio São Domingos a partir da análise geoquímica e isotópica Pb/Pb

A bacia hidrográfica do rio São Domingos constitui uma das sub-bacias do rio Muriaé pertencente ao sistema Paraíba do Sul e, tem seus limites coincidentes com os limites do município de São José de Ubá, sendo este o segundo maior produtor de tomate do estado do Rio de Janeiro, com sua principal fonte econômica baseada na agropecuária. Este tipo de atividade resulta em utilização de produtos químicos nas lavouras e juntamente a ocupação inadequada resulta em modificação das paisagens e da mata nativa, resultando em diversos tipos de impactos no ambiente. Neste estudo foram abordados os impactos relacionados a concentração de metais e sua proveniência através das assinaturas isotópicas Pb/Pb, utilizando para tal o procedimento analítico de lixiviação dos sedimentos de corrente e abertura total de rochas para a obtenção de razões isotópicas e concentrações de metais por ICP-MS. Os resultados mostraram que as contribuições nos sedimentos de corrente se dão a partir de cinco fontes compreendidos no intervalo de assinatura isotópica 206Pb/207Pb 1,1229 e 1,1949, representadas em intervalos bem definidos. Por correlação com as respectivas concentrações se observa que, preferencialmente, existe maior influência das rochas do embasamento, seguido de atividade antrópicas como a urbanização e disposição de lixo doméstico. As maiores concentrações estão associadas ao cobre, chumbo, estrôncio, níquel e zinco. Contudo todas as concentrações de metais obtidas se encontram abaixo da legislação vigente. Desta forma a contaminação antrópica é limitada a regiões de maior densidade populacional e as influências naturais predominam na área da bacia.

Avaliação da remoção de níquel em solução aquosa pelo processo de osmose inversa

O objetivo deste trabalho foi investigar o desempenho de uma membrana comercial na remoção de um metal pesado (níquel) de efluentes sintéticos, por osmose inversa. Na primeira etapa foi realizada uma comparação com os resultados obtidos com soluções de alimentação contendo sais, como NaCl, NaNO3 e Ni(NO3)2.6 H2O, nas concentrações de 50, 100 e 200 ppm, e nas pressões de 10, 20 e 26 bar. Os resultados mostraram que a influência da concentração e da pressão aplicada ao sistema não afetaram as rejeições de forma significativa. Na segunda etapa, como os parâmetros não influíram significativamente na rejeição dos sais, optou-se, pela aplicação de uma pressão de operação de 10 bar, para avaliar a eficiência de remoção de níquel. A membrana utilizada, constituída de poliamida, modelo HR98PP e fornecida pela DOW/Filmtec, apresentou uma boa permeabilidade hidráulica. Os resultados mostraram que para todas as concentrações testadas, as rejeições de níquel ultrapassaram 96%, comprovando a boa seletividade deste tipo de membrana na rejeição do referido metal, com fluxos de permeado variando entre 4,78 e 5,55 L/h.m2 , sob pressão de operação de 10 bar. Para estudar o efeito do tamanho iônico na rejeição da membrana, o níquel foi complexado pela adição de um agente quelante na solução de alimentação. O agente escolhido foi o Na2EDTA, devido à formação de um complexo estável com o níquel e por ser um agente não prejudicial à saúde humana. Os resultados com adição de EDTA indicaram um aumento na rejeição de níquel, atingindo o índice máximo de 98,22 %, partindo-se de uma solução com 40,39 ppm de Ni2+, e confirmam que o processo de osmose inversa com a membrana HR98PP é altamente adequado para o tratamento de efluentes contendo níquel

Remoção de compostos sulfurados e nitrogenados de diesel hidrotratado por adsorção em argila, alumina e sílica-alumina, impregnadas com metais de transição

Na matriz energética brasileira, o óleo diesel tem lugar de destaque, porém ainda é comercializado com teores de compostos sulfurados e nitrogenados considerados altos para as legislações ambientais que entrarão em vigor nos próximos anos. Tradicionalmente, a remoção desses compostos de enxofre de correntes de petróleo é realizada por processos de hidrotratamento (HDT). No entanto, devido as características do diesel brasileiro, se faz necessária maior severidade para atingir as novas especificações dos combustíveis. Isto implica em investimentos e custos operacionais crescentes para atender a demanda que se instala. Neste contexto, a adsorção está sendo estudada para a purificação da corrente de óleo diesel oriunda da etapa de hidrotratamento como polimento final para alcançar as especificações mais exigentes. Sabe-se que os adsorventes comerciais apresentam limitações na remoção destes contaminantes e uma alternativa que tem se mostrado promissora é a incorporação de metais de transição na estrutura do sólido. No presente trabalho foram modificados adsorventes comerciais, tais como aluminas, sílica-aluminas e argilas pela introdução dos elementos níquel, colbalto e molibdênio e testado o desempenho dessas modificações frente à adsorção de compostos sulfurados e nitrogenados presentes em um diesel hidrotratado. Foram feitas caracterizações químicas, físicas, texturais e morfológicas dos sólidos com e sem incorporação de metais de transição na estrutura original. Os experimentos de adsorção foram realizados a 40C. Avaliando todos os sólidos, o adsorvente que mostrou o melhor desempenho na remoção de compostos sulfurados e nitrogenados por massa de adsorvente foi a sílica-alumina sem modificações, que foi capaz de remover em torno de 90% de compostos nitrogenados e 55 % de sulfurados para 2 g de sólido / 10 mL de diesel. Para os materiais modificados, observou-se que a incorporação dos metais de transição ocasionou redução da sua área superficial e do volume total de poros. Desta maneira, os efeitos esperados pelas interações entre o sítios metálicos e os compostos de nitrogênio e enxofre foram reduzidos