Evolution of Ryegrass Seed Banks Depending on Soil Tillage and Crops

The seed bank is characterized by the amount of seeds and other viable reproductive structures in the soil and it is changed by the input and output of seeds, being classified by its permanence in the soil as transient or permanent. The tillage and crops used decisively influence this dynamic and more disturbed areas tend to have richer seed banks. The purpose of this study was to test different soil tillage and crop systems, aiming to reduce or eliminate the ryegrass in the area. The experiment was conducted from 2010 to 2012. In the first year, the effect of chemical tillage was assessed, compared to the area without tillage. From the second year on, in the area that received chemical tillage, the second experiment was installed, where it was assessed the effect of soil tillage and crop rotation in the ryegrass seed yield. The soil tillage treatment was chisel plow and non-chisel plow. The crop rotation was: fallow/soybean; wheat/soybean; black oat/maize. The samples of soil were taken three times a year and split in 0-5, 5-10, 10-15 and 15-20 cm. After sampling, the seeds were separated from the soil and sterilized. Afterwards, germination and tetrazolium test were conducted. In the same plots used for soil sampling, the emergence flow of ryegrass was assessed in the winter 2011 and 2012. In the first year it was observed that chemical tillage had considerably reduced the amount of ryegrass in the soil. The crop rotations used were more effective than soil tillage in reducing the seed banks in the soil. The rotation oat/maize and wheat/soybean, in only two years, practically zeroed the ryegrass seed banks in the area.

Carryover of Imazethapyr + Imazapic on Ryegrass and Non-tolerant Rice as Affected by Thickness of Soil Profile

Herbicides used in Clearfield(r) rice system may persist in the environment, damaging non-tolerant crops sown in succession and/or rotation. These damages vary according to soil characteristics, climate and soil management. The thickness of the soil profile may affect carryover effect; deeper soils may allow these molecules to leach, reaching areas below the roots absorption zone. The aim of this study was to evaluate the effect of the thickness of soil profile in the carryover of imazethapyr + imazapic on ryegrass and non-tolerant rice, sown in succession and rotation to rice, respectively. Lysimeters of different thicknesses (15, 20, 30, 40, 50 and 65 cm) were constructed, where 1 L ha-1 of the imazethapyr + imazapic formulated mixture was applied in tolerant rice. Firstly, imidazolinone-tolerant rice was planted, followed by ryegrass and non-tolerant rice in succession and rotation, respectively. Herbicide injury, height reduction and dry weight of non-tolerant species were assessed. There was no visual symptoms of herbicide injury on ryegrass sown 128 days after the herbicide application; however it causes dry weight mass reduction of plants. The herbicides persist in the soil and cause injury in non-tolerant rice, sown 280 days after application, and the deeper the soil profile, the lower the herbicides injury on irrigated rice.

SELECTION OF HERBICIDES TARGETING THE USE IN CROP SYSTEMS CULTIVATED WITH SHOWY CROTALARIA

ABSTRACT The increase in the area planted with Crotalaria spectabilishas occurred by several factors, highlighting the potential to reduce the nematodes, nitrogen fixation and the high production of biomass. By becoming a species sown as a crop, it is necessary to control the weeds that coexist with showy crotalaria. This change in the use of this crop creates the possibility of this specie becoming a weed. The aim of this study was to assess the potential use of herbicides applied in preemergence and postemergence of C.spectabilisfor different purposes (control of volunteer and selectivity plants). Three experiments were installed in a greenhouse (two with herbicides applied in preemergence - in soils with distinct textural categories; and one experiment with herbicides applied in postemergence). The results of the experiments with herbicides applied in preemergence showed that: amicarbazone, atrazine, diuron, metribuzin, prometryn, fomesafen and sulfentrazone showed effectiveness for control of C.spectabilis in clayey soil. Besides these, flumioxazin and isoxaflutole also showed potential to be used in the control of showy crotalaria in soils with loam texture. In relation to the postemergence herbicides, atrazine, diuron, prometryn, flumioxazin, fomesafen, lactofen, saflufenacil, amonio-glufosinate and glyphosate can be used aiming the chemical control of C.spectabilis. Herbicides chlorimuron-ethyl, diclosulan, imazethapyr, pyrithiobac-sodium, trifloxysulfuron-sodium, clomazone, pendimethalin, S-metolachlor and trifluralin applied in preemergence, and imazethapyr, pyrithiobac-sodium, flumiclorac, bentazon and clethodim applied in postemergence caused low levels of injury to C.spectabilis plants, making necessary the development of new searches to ensure the selectivity of these products.

Weed Community in a Raw Sugarcane Renovation Area Submitted to Different Soil Managements

The objective of this study was to evaluate the weed community in a raw sugarcane renovation area with three soil managements and peanut sowing in succession. The experiment was conducted during the 2007/08 season on a raw sugarcane area harvested without prior burning in the last five cuts. A randomized block design with treatments arranged in a split plot and arranged in four replications was used. The main treatments consisted of three cropping systems: conventional tillage, minimum tillage and direct planting, and subplots consisted in the absence (resting) or presence of crop rotation with peanuts. After 135 days from planting peanuts and 180 days of sugarcane harvest, the number of weeds m-2 was counted and the shoot dry biomass of the weeds collected was determined. The data were interpreted by analysis of variance and the means were compared by Tukey's test at 5% probability so that phytosociological indices a, b, c e d were calculated. The use of soil conservation tillage and peanut in rotation with sugarcane in the renovation areas is effective in controlling weeds and suppression of weed species difficult to control like Cyperus rotundus, Commelina bengalensis, Urochloa plantaginea, and Digitaria nuda.

Influence of reactant absorption and dissolution in heterogeneous precipitation processes

In this research work, the aim was to investigate the volumetric mass transfer coefficient [kLa] of oxygen in stirred tank in the presence of solid particle experimentally. The kLa correlations as a function of propeller rotation speed and flow rate of gas feed were studied. The O2 and CO2 absorption in water and in solid-liquid suspensions and heterogeneous precipitation of MgCO3 were thoroughly examined. The absorption experiments of oxygen were conducted in various systems like pure water and in aqueous suspensions of quartz and calcium carbonate particles. Secondly, the precipitation kinetics of magnesium carbonate was also investigated. The experiments were performed to study the reactive crystallization with magnesium hydroxide slurry and carbon dioxide gas by varying the feed rates of carbon dioxide and rotation speeds of mixer. The results of absorption and precipitation are evaluated by titration, total carbon (TC analysis), and ionic chromatrography (IC). For calcium carbonate, the particle concentration was varied from 17.4 g to 2382 g with two size fractions: 5 µm and 45-63 µm sieves. The kLa and P/V values of 17.4 g CaCO3 with particle size of 5µm and 45-63 µm were 0.016 s-1 and 2400 W/m3. At 69.9 g concentration of CaCO3, the achieved kLa is 0.014 s-1 with particle size of 5 µm and 0.017 s-1 with particle size of 45 to 63 µm. Further increase in concentration of calcium carbonate, i.e. 870g and 2382g , does not affect volumetric mass transfer coeffienct of oxygen. It could be concluded from absorption results that maximum value of kLa is 0.016 s-1. Also particle size and concentration does affect the transfer rate to some extend. For precipitation experiments, the constant concentration of Mg(OH)2 was 100 g and the rotation speed varied from 560 to 750 rpm, whereas the used feed rates of CO2 were 1 and 9 L/min. At 560 rpm and feed rate of CO2 is 1 L/min, the maximum value of Mg ion and TC were 0.25 mol/litre and 0.12 mol/litre with the residence time of 40 min. When flow rate of CO2 increased to 9 L/min with same 560 rpm, the achieved value of Mg and TC were 0.3 mol/litre and 0.12 mol/L with shorter residence time of 30 min. It is concluded that feed rate of CO2 is dominant in precipitation experiments and it has a key role in dissociation and reaction of magnesium hydroxide in precipitation of magnesium carbonate.

Comparative lifecycle assessment on organic and conventional carrots – case: Carrots from South-Savo and imported carrots from Italy

Organic farming is perceived to be an environmental friendly method of food production, thus assumed to be an alternative means of minimizing food-based environmental footprints. However, lower yield and unproductive years in organic crop rotation raise questions of whether it is really an environmentally friendly farming practice. Thus, the aim of this thesis was to examine the carbon footprint and energy demands of organic carrots cultivated and sold in South-Savo, Finland and compare them with those of local and imported conventional carrots using lifecycle assessment (LCA) as a method. From the investigation, it was found that organic carrots produced in South-Savo have the lowest GHG emissions and energy demand. The GHG emissions of local organic, local conventional and imported conventional carrots were found to be 4g CO2 eq. kgcarrots-1, 142g CO2 eq. kgcarrots-1 and 280 g CO2 eq. kgcarrots-1, respectively. On the other hand, energy demand for those carrots was found to be 1,33 MJ, 1,88 MJ and 3,68 MJ kgcarrots-1. Furthermore, it was also found that local organic carrots would have approximately similar GHG emissions as conventional counterpart if soil carbon stock change was excluded from the study.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

Slurry flows in progressive cavity and in hose pumps

The aim of this thesis was to research how slurry’s viscosity and rheology affect to pumping in peristaltic hose pump and in eccentric progressive cavity pump. In addition, it was researched the formed pressure pulsation in hose pump. Pressure pulsation was studied by pumping different slurries and by using different pipe materials. Pressure and power curves were determined for both used pumps. It was also determined NPSHR curve for the progressive cavity pump. Literature part of the thesis considered to distribute fluids to different rheology types, as well as theories and models to identify different rheology types. Special attention was paid to non-Newtonian fluids, which were also used in experimental part of this thesis. In addition, the literature part discusses about pumps, parameters for pump sizing, and pressure pulsation in hose pump. Starch, bentonite, and carboxymethyl cellulose slurries were used in the experimental part of this thesis. The slurries were pumped with Flowrox peristaltic hose pump (LPP-T32) and eccentric progressive cavity pump (C10/10). From the each slurry was taken a sample, and the samples were analyzed for concentration, viscosity and rheology type. The used pipe materials in pressure pulsation experiments were steel and elastic, and it was also used a prototype of pulsation dampener. The pulsation experiments indicated that the elastic pipe and the prototype of pulsation dampener attenuated pressure pulsation better than the steel pipe at low pressure levels. The differences between different materials disappeared when pressure level and pump rotation speed increased. In slurry experiments, pulsation was different depending on rheology and viscosity of the slurry. According to experiments, the rheology did not significantly affect to pump power consumption or efficiency.

Energiapuun kastelu jätetäytön suotovedellä tuhkasta ja kompostista valmistetussa kasvualustassa

Tässä työssä tutkitaan suotoveden käsittelyä käyttämällä sitä kierrätysmateriaaleista valmistetussa tuhkamullassa loppusijoitusalueen päällä kasvatettavan energiapuukasvuston kasteluun. Kyseisen toimintamallin tarkoituksena on haihduttaa suotovettä energiapuiden avulla sekä sitouttaa ravinteita ja haitta-aineita sekä kasvustoon että kasvualustaan. Tavoitteena on selvittää toimintamallin hyödyntämiskelpoisuus ja tehokkuus suotovesien käsittelymenetelmänä sekä kastelun vaikutukset energiapuun kasvuun. Työssä suoritettiin kesän ja syksyn 2014 aikana energiapuun kastelukoe Mustankorkea Oy:n jätteenkäsittelykeskuksen alueella Jyväskylässä. Kokeessa loppusijoitusalueen päälle istutettuja eri kasvuvaiheissa olevia energiapajukasvustoja sekä hybridihaapakasvustoa kasteltiin jätetäytön suotovedellä. Kokeessa käytettiin kasvualustoina tuhkamultaa, joka oli valmistettu tuhkasta, kompostista ja ylijäämämaa- aineksesta, sekä kompostia. Kasteluveden, valumavesien, kasvualustojen ja pajukasvuston ominaisuuksia seurattiin kokeen aikana analyysien avulla. Lisäksi alueen vesitaseen selvittämiseksi suoritettiin lysimetrikokeet, joissa lysimetreihin istutettuja pajuja kasteltiin suotovedellä sekä hanavedellä. Tulosten perusteella suotovesikastelu lisäsi sekä pajun että haavan kasvua. Kastelu lisäsi pajun ravinnepitoisuuksia. Se myös heikensi hieman pajun poltto-ominaisuuksia. Kasvualustan ominaisuuksiin kastelulla ei havaittu olevan vaikutuksia. Kastelumäärä, jota voidaan käyttää ilman valumia, on kokeen perusteella n. 100–600 mm/kasvukausi käytetyllä kastelujärjestelmällä. Kastelujärjestelmää kehittämällä on kuitenkin luultavasti mahdollista lisätä haihduntaa ja siten kastelumäärää merkittävästi.

Simulation of wind powered hydraulic heating system

The objective of this master’s thesis was to design and simulate a wind powered hydraulic heating system that can operate independently in remote places where the use of electricity is not possible. Components for the system were to be selected in such a way that the conditions for manufacture, use and economic viability are the as good as possible. Savonius rotor was chosen for wind turbine, due to its low cut in speed and robust design. Savonius rotor produces kinetic energy in wide wind speed range and it can withstand high wind gusts. Radial piston pump was chosen for the flow source of the hydraulic heater. Pump type was selected due to its characteristics in low rotation speeds and high efficiency. Volume flow from the pump is passed through the throttle orifice. Pressure drop over the orifice causes the hydraulic oil to heat up and, thus, creating thermal energy. Thermal energy in the oil is led to radiator where it conducts heat to the environment. The hydraulic heating system was simulated. For this purpose a mathematical models of chosen components were created. In simulation wind data gathered by Finnish meteorological institute for 167 hours was used as input. The highest produced power was achieved by changing the orifice diameter so that the rotor tip speed ratio follows the power curve. This is not possible to achieve without using electricity. Thus, for the orifice diameter only one, the optimal value was defined. Results from the simulation were compared with investment calculations. Different parameters effecting the investment profitability were altered in sensitivity analyses in order to define the points of investment profitability. Investment was found to be profitable only with high average wind speeds.

Daily birth numbers in Passo Fundo, South Brazil, 1997-1999: trends and periodicities

Between October 6, 1997 and April 30, 1999, 5011 births (mean: 8.76 per day) were registered in the city of Passo Fundo, South Brazil. The sequence of 572 daily birth numbers was not random (iteration test). Neyman distribution (m = ¥) showed the best fit. Clusters of days with higher birth numbers alternated with days with low numbers of births. Periodogram analysis revealed a significant periodicity of 6.98 days. The cosinor regression, testing 10 a priori supposed period lengths, found significant seasonality peaking in August-September and significantly highest birth numbers on Thursdays. Among the lunar and solar rotation cycles, the tropic lunar cycle and its 4th harmonic were most pronounced, in agreement with results concerning natality in Germany obtained by Svante Arrhenius in the 19th century. These findings confirm Derer-Halberg's concept of multiseptans. In addition to cycling, a significantly increasing linear trend with a daily increase of 0.0045 births was encountered. This documents a growth of the population in agreement with national statistical data.

Factor structure of Bech's version of the Brief Psychiatric Rating Scale in Brazilian patients

The objective of the present study was to evaluate the factor structure of Bech's version of the Brief Psychiatric Rating Scale (BPRS), translated into Portuguese. The BPRS was administered to a heterogeneous group of psychiatric inpatients (N = 98) and outpatients (N = 62) in a University Hospital. Each patient was evaluated from one to eight times. The interval between consecutive interviews was one week for the inpatients and one month for the outpatients. The results were submitted to factorial analysis. The internal consistency of the total scale and of each factor was also estimated. Factorial analysis followed by normalized orthogonal rotation (Varimax) yielded four factors: Withdrawal-Retardation, Thinking Disorder, Anxious-Depression and Activation. Internal consistency measured by Cronbach's alpha coefficient ranged from 0.766 to 0.879. The data show that the factor structure of the present instrument is similar to that of the American version of the BPRS which contains 18 items, except for the absence of the fifth factor of the latter scale, Hostile-Suspiciousness.

Effects of the conditioned medium of mesenchymal stem cells on mouse oocyte activation and development

Mesenchymal stem cells (MSCs) have been reported to secrete a variety of cytokines and growth factors acting as trophic suppliers, but little is known regarding the effects of conditioned medium (CM) of MSCs isolated from femurs and tibias of mouse on the artificial activation of mouse oocytes and on the developmental competence of the parthenotes. In the current study, we investigated the effect of CM on the events of mouse oocyte activation, namely oscillations of cytosolic calcium concentration ([Ca²+]i), meiosis resumption, pronucleus formation, and parthenogenetic development. The surface markers of MSCs were identified with a fluorescence-activated cell sorter. The dynamic changes of the spindle and formation of pronuclei were examined by laser-scanning confocal microscopy. Exposure of cumulus-oocyte complexes to CM for 40 min was optimal for inducing oocyte parthenogenetic activation and evoking [Ca²+]i oscillations similar to those evoked by sperm (95 vs 100%; P > 0.05). Parthenogenetically activated oocytes immediately treated with 7.5 µg/mL cytochalasin B (CB), which inhibited spindle rotation and second polar body extrusion, were mostly diploid (93 vs 6%, P < 0.01) while CB-untreated oocytes were mostly haploid (5 vs 83%, P < 0.01). Consequently, the blastocyst rate was higher in the CB-treated than in the CB-untreated oocytes. There was no significant difference in developmental rate between oocytes activated with CM and 7% ethanol (62 vs 62%, P > 0.05), but the developmental competence of the fertilized oocytes was superior to that of the parthenotes (88 vs 62%, P < 0.05). The present results demonstrate that CM can effectively activate mouse oocytes, as judged by the generation of [Ca²+]i oscillations, completion of meiosis and parthenogenetic development.

Three-dimensional kinematic analysis of upper and lower limb motion during gait of post-stroke patients

The aim of this study was to analyze the alterations of arm and leg movements of patients during stroke gait. Joint angles of upper and lower limbs and spatiotemporal variables were evaluated in two groups: hemiparetic group (HG, 14 hemiparetic men, 53 ± 10 years) and control group (CG, 7 able-bodied men, 50 ± 4 years). The statistical analysis was based on the following comparisons (P ≤ 0.05): 1) right versus left sides of CG; 2) affected (AF) versus unaffected (UF) sides of HG; 3) CG versus both the affected and unaffected sides of HG, and 4) an intracycle comparison of the kinematic continuous angular variables between HG and CG. This study showed that the affected upper limb motion in stroke gait was characterized by a decreased range of motion of the glenohumeral (HG: 6.3 ± 4.5, CG: 20.1 ± 8.2) and elbow joints (AF: 8.4 ± 4.4, UF: 15.6 ± 7.6) on the sagittal plane and elbow joint flexion throughout the cycle (AF: 68.2 ± 0.4, CG: 46.8 ± 2.7). The glenohumeral joint presented a higher abduction angle (AF: 14.2 ± 1.6, CG: 11.5 ± 4.0) and a lower external rotation throughout the cycle (AF: 4.6 ± 1.2, CG: 22.0 ± 3.0). The lower limbs showed typical alterations of the stroke gait patterns. Thus, the changes in upper and lower limb motion of stroke gait were identified. The description of upper limb motion in stroke gait is new and complements gait analysis.

Performance assessment of the single photon emission microscope: high spatial resolution SPECT imaging of small animal organs

The single photon emission microscope (SPEM) is an instrument developed to obtain high spatial resolution single photon emission computed tomography (SPECT) images of small structures inside the mouse brain. SPEM consists of two independent imaging devices, which combine a multipinhole collimator, a high-resolution, thallium-doped cesium iodide [CsI(Tl)] columnar scintillator, a demagnifying/intensifier tube, and an electron-multiplying charge-coupling device (CCD). Collimators have 300- and 450-µm diameter pinholes on tungsten slabs, in hexagonal arrays of 19 and 7 holes. Projection data are acquired in a photon-counting strategy, where CCD frames are stored at 50 frames per second, with a radius of rotation of 35 mm and magnification factor of one. The image reconstruction software tool is based on the maximum likelihood algorithm. Our aim was to evaluate the spatial resolution and sensitivity attainable with the seven-pinhole imaging device, together with the linearity for quantification on the tomographic images, and to test the instrument in obtaining tomographic images of different mouse organs. A spatial resolution better than 500 µm and a sensitivity of 21.6 counts·s-1·MBq-1 were reached, as well as a correlation coefficient between activity and intensity better than 0.99, when imaging 99mTc sources. Images of the thyroid, heart, lungs, and bones of mice were registered using 99mTc-labeled radiopharmaceuticals in times appropriate for routine preclinical experimentation of <1 h per projection data set. Detailed experimental protocols and images of the aforementioned organs are shown. We plan to extend the instrument's field of view to fix larger animals and to combine data from both detectors to reduce the acquisition time or applied activity.