Analytical study and evaluation results of power optimizers for distributed power conditioning in PV arrays

The use of modular or ‘micro’ maximum power point tracking (MPPT) converters at module level in series association, commercially known as “power optimizers”, allows the individual adaptation of each panel to the load, solving part of the problems related to partial shadows and different tilt and/or orientation angles of the photovoltaic (PV) modules. This is particularly relevant in building integrated PV systems. This paper presents useful behavioural analytical studies of cascade MPPT converters and evaluation test results of a prototype developed under a Spanish national research project. On the one hand, this work focuses on the development of new useful expressions which can be used to identify the behaviour of individual MPPT converters applied to each module and connected in series, in a typical grid-connected PV system. On the other hand, a novel characterization method of MPPT converters is developed, and experimental results of the prototype are obtained: when individual partial shading is applied, and they are connected in a typical grid connected PV array

Comparison on the durability of different portland cements after five years exposure to sulfate and to sea water attack

Experimental research has been performed to relate specific cement characteristics to deterioration due to sulfate and sea water attack after five year exposure, and to study different test method suitability for sulfate and marine resistance. Sulfate resistance testing have been performed on mortar specimens made with fifteen cement types of statistically diverse chemical composition according to European standard EN 197-1, most of them with sulfate resistant properties according to Spanish regulations. Chemical and mechanical characteristics were studied to determine the variation in properties of selected cements. SO3 content, type and amount of additions, C3A, and C4AF content were used to examine relationships between these characteristics and the results of sulfate resistance. Mortar specimens testing using Na2SO4 as the aggressive medium according to ASTM 1012 (with w/c ratio adapted to prENV 196-X:1995) was performed using each type of cement; identical specimens were also stored in sea water, and in lime saturated water (blank condition), up to five year age. Additionally these cements were tested conforming ASTM 452 and Koch and Steinegger test. Recommended acceptance limits for sulfate resistance of cements concerning to each used test method were evaluated in order to explore their suitability. Relationships between cement characteristics, degradation, expansive products obtained by X-ray diffraction techniques and maximum expansion after applied storage treatments, were correlated at final age, to redefine cement characteristics for sulfate resistant and marine resistant Portland cement

Optimization of the irrigation time and irrigation frequency by using Hydrus-2D and a capacitance FDR sensor

The evolution of water content on a sandy soil during the sprinkler irrigation campaign, in the summer of 2010, of a field of sugar beet crop located at Valladolid (Spain) is assessed by a capacitive FDR (Frequency Domain Reflectometry) EnviroScan. This field is one of the experimental sites of the Spanish research center for the sugar beet development (AIMCRA). The objective of the work focus on monitoring the soil water content evolution of consecutive irrigations during the second two weeks of July (from the 12th to the 28th). These measurements will be used to simulate water movement by means of Hydrus-2D. The water probe logged water content readings (m3/m3) at 10, 20, 40 and 60 cm depth every 30 minutes. The probe was placed between two rows in one of the typical 12 x 15 m sprinkler irrigation framework. Furthermore, a texture analysis at the soil profile was also conducted. The irrigation frequency in this farm was set by the own personal farmer 0 s criteria that aiming to minimizing electricity pumping costs, used to irrigate at night and during the weekend i.e. longer irrigation frequency than expected. However, the high evapotranspiration rates and the weekly sugar beet water consumption—up to 50mm/week—clearly determined the need for lower this frequency. Moreover, farmer used to irrigate for six or five hours whilst results from the EnviroScan probe showed the soil profile reaching saturation point after the first three hours. It must be noted that AIMCRA provides to his members with a SMS service regarding weekly sugar beet water requirement; from the use of different meteorological stations and evapotranspiration pans, farmers have an idea of the weekly irrigation needs. Nevertheless, it is the farmer 0 s decision to decide how to irrigate. Thus, in order to minimize water stress and pumping costs, a suitable irrigation time and irrigation frequency was modeled with Hydrus-2D. Results for the period above mentioned showed values of water content ranging from 35 and 30 (m3/m3) for the first 10 and 20cm profile depth (two hours after irrigation) to the minimum 14 and 13 (m3/m3) ( two hours before irrigation). For the 40 and 60 cm profile depth, water content moves steadily across the dates: The greater the root activity the greater the water content variation. According to the results in the EnviroScan probe and the modeling in Hydrus-2D, shorter frequencies and irrigation times are suggested.

Health and safety in the construction : subject pending to be included in the curriculum of architecture in Spain

The art of construction is a risky activity that directly affects the life and physical integrity of persons. Since the approval of Law 31/1995, of November 8, Prevention of Occupational Risks was the first legislation that established the current basis in all sectors and then transposed into Spanish law Directive 92/57/CEE called Royal Decree 1627/1997 of October 24, on minimum safety and health dispositions in construction works, measures have been proposed to develop a mixed body of scientific literature composed of researchers and professionals in the field of occupational safety and health, but even today there is still no clear and firm proposal, showing a lack of awareness in the occupational risk prevention and, therefore, a consolidation of the culture of prevention in society. Therefore, the technicians, who make up the building process, can incur in very high responsibilities, such as: Author of the project, Coordinator of Safety and Health during the preparation of the project and during the execution of works, Site Management: Site Manager. This involves the immediate creation of a general training in prevention for all architects starting when still studying, as well as specific training, appropriate and complementary to all the architects that will be devoted to the specialty of occupational safety and health in construction works. That is, first, we must make the responsible bodies aware of the urgent need to integrate risk prevention in the curricula of architecture and later in the continuing education of the profession. It is necessary that our teaching must conform to the laws on safety and health, due to the fact that the law recognizes our academic degrees and professional qualifications to perform functions in that area

A proposal for improving safety in construction projects by strengthening coordinators’ competencies in health and safety issues

The figure of the coordinator in health and safety issues in the construction sector first appeared in our legislation through the incorporation of the European Directives (in our case Royal Decree 1627/97 on the minimum health and safety regulations in construction works), and is viewed differently in different countries of the European Union regarding the way they are hired and their role in the construction industry. Coordinating health and safety issues is also a management process that requires certain competencies that are not only based on technical or professional training, but which, taking account of the work environment, require the use of strategies and tools that are related to experience and personal skills. Through a piece of research that took account of expert opinions in the matter, we have found which competencies need to be possessed by the health and safety coordinator in order to improve the safety in the works they are coordinating. The conclusions of the analyses performed using the appropriate statistical methods (comparing means and multivariate analysis techniques), will enable training programmes to be designed and ensure that the health and safety coordinators selected have the competencies required to carry out their duties.

A proposal for improving safety in construction projects by strengthening coordinators’ competencies in health and safety issues

The figure of the coordinator in health and safety issues in the construction sector first appeared in our legislation through the incorporation of the European Directives (in our case Royal Decree 1627/97 on the minimum health and safety regulations in construction works), and is viewed differently in different countries of the European Union regarding the way they are hired and their role in the construction industry. Coordinating health and safety issues is also a management process that requires certain competencies that are not only based on technical or professional training, but which, taking account of the work environment, require the use of strategies and tools that are related to experience and personal skills. Through a piece of research that took account of expert opinions in the matter, we have found which competencies need to be possessed by the health and safety coordinator in order to improve the safety in the works they are coordinating. The conclusions of the analyses performed using the appropriate statistical methods (comparing means and multivariate analysis techniques), will enable training programmes to be designed and ensure that the health and safety coordinators selected have the competencies required to carry out their duties.

Influence of some oenological practices on the aromatic and sensorial characteristics of white Verdejo wines

Changes in the aromatic composition as well as sensory characteristics in Verdejo white wines were analysed based on two factors: the winemaking methodology and the storing time of wine in bottles. The volatile components were determined by GLC-MS, and the sensory profile was designed and assessed according to the ISO 11035 standard. The results showed that when wines were made in oak barrels, either completely or partially, which means the wines were in contact with the lees, the levels of 1-octanol, ethyl heptanoate and ethyl decanoate were significantly affected (P menor que 0.05); the softness sensation was also influenced (P menor que 0.05). However, the amount of time the wines were stored in bottles significantly affected (P menor que 0.05) the levels of 1-hexanol, ethyl heptanoate, ethyl octanoate, ethyl decanoate, hexyl acetate, isoamyl acetate and isoamyl lactate and also an odour note (tropical fruit). The compounds with higher OAV values belong to the groups of esters and fatty acids. For these reasons, the composition and the quality of the aroma of Verdejo white wines appear to be significantly affected both by use of oak barrels in winemaking and the time the wines are stored in bottles.

Extreme pointer years in tree-ring records of central Spain as evidence of climatic events and the eruption of the Huaynaputina Volcano (Peru, 1600 AD)

The study of pointer years of numerous tree-ring chronologies of the central Iberian Peninsula (Sierra de Guadarrama) could provide complementary information about climate variability over the last 405 yr. In total, 64 pointer years have been identified: 30 negative (representing minimum growths) and 34 positive (representing maximum growths), the most significant of these being 1601, 1963 and 1996 for the negative ones, and 1734 and 1737 for the positive ones. Given that summer precipitation was found to be the most limiting factor for the growth of Pinus in the Sierra de Guadarrama in the second half of the 20th century, it is also an explanatory factor in almost 50% of the extreme growths. Furthermore, these pointer years and intervals are not evenly distributed throughout time. Both in the first half of the 17th and in the second half of 20th, they were more frequent and more extreme and these periods are the most notable for the frequency of negative pointer years in Central Spain. The interval 1600–1602 is of special significance, being one of the most unfavourable for tree growth in the centre of Spain, with 1601 representing the minimum index in the regional chronology. We infer that this special minimum annual increase was the effect of the eruption of Huaynaputina, which occurred in Peru at the beginning of 1600 AD. This is the first time that the effects of this eruption in the tree-ring records of Southern Europe have been demonstrated.

Effects of different soil management practices on soil mechanic resistance and seed depth placement in a maize crop in Alentejo, Portugal Mediterranean region.

No tillage, minimum tillage and conventional tillage practices are commonly used in maize crops in Alentejo, affecting soil physic conditions and determining seeders performance. Seeders distribution can be evaluated in the longitudinal and vertical planes. Vertical plane is specified by seeding depth (Karayel et al., 2008). If, in one hand seeding depth uniformity is a goal for all crop establishment , in the other hand, seeders furrow openers depth control is never constant depending on soil conditions. Seed depth uniformity affects crop emergence, Liu et al. (2004) showed an higher correlation between crop productivity and emergence uniformity than with longitudinal plants distribution. Neto et al. (2007) evaluating seed depth placement by measuring maize mesocotyl length under no tillage conditions in 38 farms concluded that 20% of coefficient of variation suggests the need of improvement seeders depth control mechanisms. The objective of this study was to evaluate casual relationships and create spatial variability maps between soil mechanic resistance and vertical distribution under three different soil practices to improve seed depth uniformity.

Assessment of CTF boiling transition and critical heat flux modeling capabilities using the OECD/NRC BFBT and PSBT benchmark databases

Over the last few years, the Pennsylvania State University (PSU) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has prepared, organized, conducted, and summarized two international benchmarks based on the NUPEC data—the OECD/NRC Full-Size Fine-Mesh Bundle Test (BFBT) Benchmark and the OECD/NRC PWR Sub-Channel and Bundle Test (PSBT) Benchmark. The benchmarks’ activities have been conducted in cooperation with the Nuclear Energy Agency/Organization for Economic Co-operation and Development (NEA/OECD) and the Japan Nuclear Energy Safety (JNES) Organization. This paper presents an application of the joint Penn State University/Technical University of Madrid (UPM) version of the well-known sub-channel code COBRA-TF (Coolant Boiling in Rod Array-Two Fluid), namely, CTF, to the steady state critical power and departure from nucleate boiling (DNB) exercises of the OECD/NRC BFBT and PSBT benchmarks. The goal is two-fold: firstly, to assess these models and to examine their strengths and weaknesses; and secondly, to identify the areas for improvement.

Optimisation of a Low-Speed Wind Tunnel. Analysis and Redesign of Corner Vanes.

This paper includes the experimental study, analysis, redesign and subsequent test of the parts of a closed circuit, low speed wind tunnel which are relevant in terms of total pressure loss. The objective is to lower the energy consumption of this system for given conditions in test chamber, so as to reduce the operational costs. In order to achieve this objective, several tasks were performed as the text shows in its different parts. For these tasks, the ETSIAE wind tunnel was used, although the results of this work can be extrapolated to any wind tunnel with the same characteristics. Part II presents a theoretical previous study of the general running of a closed circuit, low speed wind tunnel, as well as the followed procedure to conduct experimental tests for obtaining the total pressure loss in its parts. Results from these tests and their analysis are included in this part. In part III, the analysis of the influence of corner 1 on the pressure loss takes place. As it is said in this part, corner 1 has great importance in the total pressure loss of the wind tunnel. Therefore, it is the first part that should be modified in order to improve the performances of the wind tunnel. During part IV, an optimised guide vane is designed in order to reduce the pressure loss in corner 1 of the wind tunnel. Software MISES is used to achieve this goal by means of selecting the optimum guide vane. In order to introduce the new guide vane in wind tunnels with affordable costs, the easily constructable criterion is kept during design. For this reason, the guide vane will consist of simple aerodynamic contours. Part V includes some possible improvements for the proposed guide vane, in order to evaluate if there is room for improvement in its design. Finally, part VI includes the tests that were conducted in the wind tunnel with the new guide vane cascade and the analysis of their results, in order to asses whether the proposed design fulfills the requirement of lowering the total pressure loss in the wind tunnel. Part VII gathers the main ideas resulting from the whole work.

Metodología de análisis estadístico de roturas en redes de distribución de agua

La presente Tesis plantea una metodología de análisis estadístico de roturas de tubería en redes de distribución de agua, que analiza la relación entre las roturas y la presión de agua y que propone la implantación de una gestión de presiones que reduzca el número de roturas que se producen en dichas redes. Las redes de distribución de agua se deterioran y una de sus graves consecuencias es la aparición de roturas frecuentes en sus tuberías. Las roturas llevan asociados elevados costes sociales, económicos y medioambientales y es por ello por lo que las compañías gestoras del agua tratan de reducirlas en la medida de lo posible. Las redes de distribución de agua se pueden dividir en zonas o sectores que facilitan su control y que pueden ser independientes o aislarse mediante válvulas, como ocurre en las redes de países más desarrollados, o pueden estar intercomunicados hidráulicamente. La implantación de una gestión de presiones suele llevarse a cabo a través de las válvulas reductoras de presión (VPR), que se instalan en las cabeceras de estos sectores y que controlan la presión aguas abajo de la misma, aunque varíe su caudal de entrada. Los métodos más conocidos de la gestión de presiones son la reducción de presiones, que es el control más habitual, el mantenimiento de la presión, la prevención y/o alivio de los aumentos repentinos de presión y el establecimiento de un control por alturas. A partir del año 2005 se empezó a reconocer el efecto de la gestión de presiones sobre la disminución de las roturas. En esta Tesis, se sugiere una gestión de presiones que controle los rangos de los indicadores de la presión de cabecera que más influyan en la probabilidad de roturas de tubería. Así, la presión del agua se caracteriza a través de indicadores obtenidos de la presión registrada en la cabecera de los sectores, debido a que se asume que esta presión es representativa de la presión de operación de todas las tuberías porque las pérdidas de carga son relativamente bajas y las diferencias topográficas se tienen en cuenta en el diseño de los sectores. Y los indicadores de presión, que se pueden definir como el estadístico calculado a partir de las series de la presión de cabecera sobre una ventana de tiempo, pueden proveer la información necesaria para ayudar a la toma de decisiones a los gestores del agua con el fin de reducir las roturas de tubería en las redes de distribución de agua. La primera parte de la metodología que se propone en esta Tesis trata de encontrar los indicadores de presión que influyen más en la probabilidad de roturas de tuberías. Para conocer si un indicador es influyente en la probabilidad de las roturas se comparan las estimaciones de las funciones de distribución acumulada (FDAs) de los indicadores de presiones, considerando dos situaciones: cuando se condicionan a la ocurrencia de una rotura (suceso raro) y cuando se calculan en la situación normal de operación (normal operación). Por lo general, las compañías gestoras cuentan con registros de roturas de los años más recientes y al encontrarse las tuberías enterradas se complica el acceso a la información. Por ello, se propone el uso de funciones de probabilidad que permiten reducir la incertidumbre asociada a los datos registrados. De esta forma, se determinan las funciones de distribución acumuladas (FDAs) de los valores del indicador de la serie de presión (situación normal de operación) y las FDAs de los valores del indicador en el momento de ocurrencia de las roturas (condicionado a las roturas). Si las funciones de distribución provienen de la misma población, no se puede deducir que el indicador claramente influya en la probabilidad de roturas. Sin embargo, si se prueba estadísticamente que las funciones proceden de la misma población, se puede concluir que existe una relación entre el indicador analizado y la ocurrencia de las roturas. Debido a que el número de valores del indicador de la FDA condicionada a las roturas es mucho menor que el número de valores del indicador de la FDA incondicional a las roturas, se generan series aleatorias a partir de los valores de los indicadores con el mismo número de valores que roturas registradas hay. De esta forma, se comparan las FDAs de series aleatorias del indicador con la FDA condicionada a las roturas del mismo indicador y se deduce si el indicador es influyente en la probabilidad de las roturas. Los indicadores de presión pueden depender de unos parámetros. A través de un análisis de sensibilidad y aplicando un test estadístico robusto se determina la situación en la que estos parámetros dan lugar a que el indicador sea más influyente en la probabilidad de las roturas. Al mismo tiempo, los indicadores se pueden calcular en función de dos parámetros de cálculo que se denominan el tiempo de anticipación y el ancho de ventana. El tiempo de anticipación es el tiempo (en horas) entre el final del periodo de computación del indicador de presión y la rotura, y el ancho de ventana es el número de valores de presión que se requieren para calcular el indicador de presión y que es múltiplo de 24 horas debido al comportamiento cíclico diario de la presión. Un análisis de sensibilidad de los parámetros de cálculo explica cuándo los indicadores de presión influyen más en la probabilidad de roturas. En la segunda parte de la metodología se presenta un modelo de diagnóstico bayesiano. Este tipo de modelo forma parte de los modelos estadísticos de prevención de roturas, parten de los datos registrados para establecer patrones de fallo y utilizan el teorema de Bayes para determinar la probabilidad de fallo cuando se condiciona la red a unas determinadas características. Así, a través del teorema de Bayes se comparan la FDA genérica del indicador con la FDA condicionada a las roturas y se determina cuándo la probabilidad de roturas aumenta para ciertos rangos del indicador que se ha inferido como influyente en las roturas. Se determina un ratio de probabilidad (RP) que cuando es superior a la unidad permite distinguir cuándo la probabilidad de roturas incrementa para determinados intervalos del indicador. La primera parte de la metodología se aplica a la red de distribución de la Comunidad de Madrid (España) y a la red de distribución de Ciudad de Panamá (Panamá). Tras el filtrado de datos se deduce que se puede aplicar la metodología en 15 sectores en la Comunidad de Madrid y en dos sectores, llamados corregimientos, en Ciudad de Panamá. Los resultados demuestran que en las dos redes los indicadores más influyentes en la probabilidad de las roturas son el rango de la presión, que supone la diferencia entre la presión máxima y la presión mínima, y la variabilidad de la presión, que considera la propiedad estadística de la desviación típica. Se trata, por tanto, de indicadores que hacen referencia a la dispersión de los datos, a la persistencia de la variación de la presión y que se puede asimilar en resistencia de materiales a la fatiga. La segunda parte de la metodología se ha aplicado a los indicadores influyentes en la probabilidad de las roturas de la Comunidad de Madrid y se ha deducido que la probabilidad de roturas aumenta para valores extremos del indicador del rango de la presión y del indicador de la variabilidad de la presión. Finalmente, se recomienda una gestión de presiones que limite los intervalos de los indicadores influyentes en la probabilidad de roturas que incrementen dicha probabilidad. La metodología propuesta puede aplicarse a otras redes de distribución y puede ayudar a las compañías gestoras a reducir el número de fallos en el sistema a través de la gestión de presiones. This Thesis presents a methodology for the statistical analysis of pipe breaks in water distribution networks. The methodology studies the relationship between pipe breaks and water pressure, and proposes a pressure management procedure to reduce the number of breaks that occur in such networks. One of the manifestations of the deterioration of water supply systems is frequent pipe breaks. System failures are one of the major challenges faced by water utilities, due to their associated social, economic and environmental costs. For all these reasons, water utilities aim at reducing the problem of break occurrence to as great an extent as possible. Water distribution networks can be divided into areas or sectors, which facilitates the control of the network. These areas may be independent or isolated by valves, as it usually happens in developing countries. Alternatively, they can be hydraulically interconnected. The implementation of pressure management strategies is usually carried out through pressure-reducing valves (PRV). These valves are installed at the head of the sectors and, although the inflow may vary significantly, they control the downstream pressure. The most popular methods of pressure management consist of pressure reduction, which is the common form of control, pressure sustaining, prevention and/or alleviation of pressure surges or large variations in pressure, and level/altitude control. From 2005 onwards, the effects of pressure management on burst frequencies have become more widely recognized in the technical literature. This thesis suggests a pressure management that controls the pressure indicator ranges most influential on the probability of pipe breaks. Operating pressure in a sector is characterized by means of a pressure indicator at the head of the DMA, as head losses are relatively small and topographical differences were accounted for at the design stage. The pressure indicator, which may be defined as the calculated statistic from the time series of pressure head over a specific time window, may provide necessary information to help water utilities to make decisions to reduce pipe breaks in water distribution networks. The first part of the methodology presented in this Thesis provides the pressure indicators which have the greatest impact on the probability of pipe breaks to be determined. In order to know whether a pressure indicator influences the probability of pipe breaks, the proposed methodology compares estimates of cumulative distribution functions (CDFs) of a pressure indicator through consideration of two situations: when they are conditioned to the occurrence of a pipe break (a rare event), and when they are not (a normal operation). Water utilities usually have a history of failures limited to recent periods of time, and it is difficult to have access to precise information in an underground network. Therefore, the use of distribution functions to address such imprecision of recorded data is proposed. Cumulative distribution functions (CDFs) derived from the time series of pressure indicators (normal operation) and CDFs of indicator values at times coincident with a reported pipe break (conditioned to breaks) are compared. If all estimated CDFs are drawn from the same population, there is no reason to infer that the studied indicator clearly influences the probability of the rare event. However, when it is statistically proven that the estimated CDFs do not come from the same population, the analysed indicator may have an influence on the occurrence of pipe breaks. Due to the fact that the number of indicator values used to estimate the CDF conditioned to breaks is much lower in comparison with the number of indicator values to estimate the CDF of the unconditional pressure series, and that the obtained results depend on the size of the compared samples, CDFs from random sets of the same size sampled from the unconditional indicator values are estimated. Therefore, the comparison between the estimated CDFs of random sets of the indicator and the estimated CDF conditioned to breaks allows knowledge of if the indicator is influential on the probability of pipe breaks. Pressure indicators depend on various parameters. Sensitivity analysis and a robust statistical test allow determining the indicator for which these parameters result most influential on the probability of pipe breaks. At the same time, indicators can be calculated according to two model parameters, named as the anticipation time and the window width. The anticipation time refers to the time (hours) between the end of the period for the computation of the pressure indicator and the break. The window width is the number of instantaneous pressure values required to calculate the pressure indicator and is multiple of 24 hours, as water pressure has a cyclical behaviour which lasts one day. A sensitivity analysis of the model parameters explains when the pressure indicator is more influential on the probability of pipe breaks. The second part of the methodology presents a Bayesian diagnostic model. This kind of model belongs to the class of statistical predictive models, which are based on historical data, represent break behavior and patterns in water mains, and use the Bayes’ theorem to condition the probability of failure to specific system characteristics. The Bayes’ theorem allows comparing the break-conditioned FDA and the unconditional FDA of the indicators and determining when the probability of pipe breaks increases for certain pressure indicator ranges. A defined probability ratio provides a measure to establish whether the probability of breaks increases for certain ranges of the pressure indicator. The first part of the methodology is applied to the water distribution network of Madrid (Spain) and to the water distribution network of Panama City (Panama). The data filtering method suggests that the methodology can be applied to 15 sectors in Madrid and to two areas in Panama City. The results show that, in both systems, the most influential indicators on the probability of pipe breaks are the pressure range, which is the difference between the maximum pressure and the minimum pressure, and pressure variability, referred to the statistical property of the standard deviation. Therefore, they represent the dispersion of the data, the persistence of the variation in pressure and may be related to the fatigue in material resistance. The second part of the methodology has been applied to the influential indicators on the probability of pipe breaks in the water distribution network of Madrid. The main conclusion is that the probability of pipe breaks increases for the extreme values of the pressure range indicator and of the pressure variability indicator. Finally, a pressure management which limits the ranges of the pressure indicators influential on the probability of pipe breaks that increase such probability is recommended. The methodology presented here is general, may be applied to other water distribution networks, and could help water utilities reduce the number of system failures through pressure management.

Fracture micromechanisms and mechanical behavior of YBCO bulk superconductors at 77 and 300 K

In this study two YBa2Cu3O7−δ bulk superconductors were evaluated, with the aim of analyzing the influence of the processing method (TSMG and Bridgman) and the test temperature on their mechanical behavior. The relationship between their mechanical properties and fracture micromechanisms has also been studied. Both materials were tested at room and at service temperature. TPB tests were carried out to determine their mechanical behavior, strength and toughness. Moreover, one of the two materials, characterized by transversal microstructural anisotropy, was tested in two directions. Hardness of both materials at nano and micro scale was studied. The results show that the mechanical behavior of the materials is controlled by the defects and cracks that have been introduced during the processing of the materials. A good degree of agreement was found between the experimental crack defects detected by means of SEM and those gathered from the fracture mechanical analysis of the experimental data

Efectos de una intervención nutricional personalizada a largo plazo sobre los hábitos alimentarios de jugadores profesionales de baloncesto y su influencia en la percepción del esfuerzo y la fatiga

El presente trabajo consistió en el desarrollo de una intervención nutricional a largo plazo llevada a cabo con jugadores profesionales de baloncesto, en función al cumplimiento de las recomendaciones nutricionales, con los siguientes dos objetivos: 1) valorar los cambios que dicha intervención produce sobre las prácticas nutricionales diarias de estos deportistas y 2) conocer la influencia de las modificaciones nutricionales producidas sobre la tasa de percepción del esfuerzo por sesión (RPE-Sesión) y la fatiga, a lo largo de una temporada competitiva, tanto para entrenamientos como partidos oficiales. Los objetivos del estudio se fundamentan en: 1) la numerosa evidencia científica que muestra la inadecuación de los hábitos nutricionales de los jugadores de baloncesto y otros deportistas respecto a las recomendaciones nutricionales; 2) el hecho ampliamente reconocido en la literatura especializada de que una ingesta nutricional óptima permite maximizar el rendimiento deportivo (a nivel físico y cognitivo), promoviendo una rápida recuperación y disminuyendo el riesgo de enfermedades y lesiones deportivas. No obstante, pocos estudios han llevado a cabo una intervención nutricional a largo plazo para mejorar los hábitos alimentarios de los deportistas y ninguno de ellos fue realizado con jugadores de baloncesto; 3) la elevada correlación entre la percepción del esfuerzo (RPE) y variables fisiológicas relacionadas al desarrollo de un ejercicio (por ej.: frecuencia cardíaca, consumo máximo de oxígeno o lactato sanguíneo) y los múltiples estudios que muestran la atenuación de la RPE durante la realización del ejercicio mediante una ingesta puntual de nutrientes, (especialmente de hidratos de carbono) aunque ninguno fue desarrollado en baloncesto; 4) el estudio incipiente de la relación entre la ingesta nutricional y la RPE-Sesión, siendo éste un método validado en baloncesto y otros deportes de equipo como indicador de la carga de trabajo interna, el rendimiento deportivo y la intensidad del ejercicio realizado; 5) el hecho de que la fatiga constituye uno de los principales factores influyentes en la percepción del esfuerzo y puede ser retrasada y/o atenuada mediante la ingesta de carbohidratos, pudiendo disminuir consecuentemente la RPE-Sesión y la carga interna del esfuerzo físico, potenciando el rendimiento deportivo y las adaptaciones inducidas por el entrenamiento; 6) la reducida evidencia acerca del comportamiento de la RPE-Sesión ante la modificación de la ingesta de nutrientes, encontrándose sólo un estudio llevado a cabo en baloncesto y 7) la ausencia de investigaciones acerca de la influencia que puede tener la mejora del patrón nutricional de los jugadores sobre la RPE-Sesión y la fatiga, desconociéndose si la adecuación de los hábitos nutricionales conduce a una disminución de estas variables en el largo plazo para todos los entrenamientos y partidos oficiales a nivel profesional. Por todo esto, este trabajo comienza con una introducción que presenta el marco teórico de la importancia y función de la nutrición en el deporte, así como de las recomendaciones nutricionales actuales a nivel general y para baloncesto. Además, se describen las intervenciones nutricionales llevadas a cabo previamente con otros deportistas y las consecuentes modificaciones sobre el patrón alimentario, coincidiendo este aspecto con el primer objetivo del presente estudio. Posteriormente, se analiza la RPE, la RPE-Sesión y la fatiga, focalizando el estudio en la relación de dichas variables con la carga de trabajo físico, la intensidad del entrenamiento, el rendimiento deportivo y la recuperación post ejercicio. Finalmente, se combinan todos los aspectos mencionados: ingesta nutricional, RPE percepción del esfuerzo y fatiga, con el fin de conocer la situación actual del estudio de la relación entre dichas variables, conformando la base del segundo objetivo de este estudio. Seguidamente, se exponen y fundamentan los objetivos antes mencionados, para dar lugar después a la explicación de la metodología utilizada en el presente estudio. Ésta consistió en un diseño de estudios de caso, aplicándose una intervención nutricional personalizada a tres jugadores de baloncesto profesional (cada jugador = un estudio de caso; n = 1), con el objetivo de adecuar su ingesta nutricional en el largo plazo a las recomendaciones nutricionales. A su vez, se analizó la respuesta individual de cada uno de los casos a dicha intervención para los dos objetivos del estudio. Para ello, cada jugador completó un registro diario de alimentos (7 días; pesada de alimentos) antes, durante y al final de la intervención. Además, los sujetos registraron diariamente a lo largo del estudio la RPE-Sesión y la fatiga en entrenamientos físicos y de balón y en partidos oficiales de liga, controlándose además en forma cuantitativa otras variables influyentes como el estado de ánimo y el sueño. El análisis de los datos consistió en el cálculo de los estadísticos descriptivos para todas las variables, la comparación de la ingesta en los diferentes momentos evaluados con las recomendaciones nutricionales y una comparación de medias no paramétrica entre el período pre intervención y durante la intervención con el test de Wilcoxon (medidas repetidas) para todas las variables. Finalmente, se relacionaron los cambios obtenidos en la ingesta nutricional con la percepción del esfuerzo y la fatiga y la posible influencia del estado de ánimo y el sueño, a través de un estudio correlacional (Tau_b de Kendall). Posteriormente, se presentan los resultados obtenidos y la discusión de los mismos, haciendo referencia a la evidencia científica relacionada que se encuentra publicada hasta el momento, la cual facilitó el análisis de la relación entre RPE-Sesión, fatiga y nutrición a lo largo de una temporada. Los principales hallazgos y su correspondiente análisis, por lo tanto, pueden resumirse en los siguientes: 1) los tres jugadores de baloncesto profesional presentaron inicialmente hábitos nutricionales inadecuados, haciendo evidente la necesidad de un nutricionista deportivo dentro del cuerpo técnico de los equipos profesionales; 2) las principales deficiencias correspondieron a un déficit pronunciado de energía e hidratos de carbono, que fueron reducidas con la intervención nutricional; 3) la ingesta excesiva de grasa total, ácidos grasos saturados, etanol y proteínas que se halló en alguno/s de los casos, también se adecuó a las recomendaciones después de la intervención; 4) la media obtenida durante un período de la temporada para la RPE-Sesión y la fatiga de entrenamientos, podría ser disminuida en un jugador individual mediante el incremento de su ingesta de carbohidratos a largo plazo, siempre que no existan alteraciones psico-emocionales relevantes; 5) el comportamiento de la RPE-Sesión de partidos oficiales no parece estar influido por los factores nutricionales modificados en este estudio, dependiendo más de la variación de elementos externos no controlables, intrínsecos a los partidos de baloncesto profesional. Ante estos resultados, se pudo observar que las diferentes características de los jugadores y las distintas respuestas obtenidas después de la intervención, reforzaron la importancia de utilizar un diseño de estudio de casos para el análisis de los deportistas de élite y, asimismo, de realizar un asesoramiento nutricional personalizado. Del mismo modo, la percepción del esfuerzo y la fatiga de cada jugador evolucionaron de manera diferente después de la intervención nutricional, lo cual podría depender de las diferentes características de los sujetos, a nivel físico, psico-social, emocional y contextual. Por ello, se propone que el control riguroso de las variables cualitativas que parecen influir sobre la RPE y la fatiga a largo plazo, facilitaría la comprensión de los datos y la determinación de factores desconocidos que influyen sobre estas variables. Finalmente, al ser la RPE-Sesión un indicador directo de la carga interna del entrenamiento, es decir, del estrés psico-fisiológico experimentado por el deportista, la posible atenuación de esta variable mediante la adecuación de los hábitos nutricionales, permitiría aplicar las cargas externas de entrenamiento planificadas, con menor estrés interno y mejor recuperación entre sesiones, disminuyendo también la sensación de fatiga, a pesar del avance de la temporada. ABSTRACT This study consisted in a long-term nutritional intervention carried out with professional basketball players according to nutritional recommendations, with the following two main objectives: 1) to evaluate the changes produced by the intervention on daily nutritional practices of these athletes and 2) to determine the influence of long term nutritional intake modifications on the rate of perceived exertion per session (Session-RPE) and fatigue, throughout a competitive season for training as well as competition games. These objectives are based on: 1) much scientific evidence that shows an inadequacy of the nutritional habits of basketball players and other athletes regarding nutritional recommendations; 2) the fact widely recognized in the scientific literature that an optimal nutrition allows to achieve the maximum performance of an athlete (both physically and cognitively), promoting fast recovery and decreasing risks of sports injuries and illnesses. However, only few studies carried out a long term nutritional intervention to improve nutritional practices of athletes and it could not be found any research with basketball players; 3) the high correlation between the rate of perceived exertion (RPE) and physiological variables related to the performance of physical exercise (e.g.: heart rate, maximum consumption of oxygen or blood lactate) and multiple studies showing the attenuation of RPE during exercise due to the intake of certain nutrients (especially carbohydrates), while none of them was developed in basketball; 4) correlation between nutritional intake and Session-RPE has been recently studied for the first time. Session-RPE method has been validated in basketball players and other team sports as an indicator of internal workload, sports performance and exercise intensity; 5) fatigue is considered one of the main influential factor on RPE and sport performance. It has also been observed that carbohydrates intake may delay or mitigate the onset of fatigue and, thus, decrease the perceived exertion and the internal training load, which could improve sports performance and training-induced adaptations; 6) there are few studies evaluating the influence of nutrient intake on Session-RPE and only one of them has been carried out with basketball players. Moreover, it has not been analyzed the possible effects of the adequacy of players’ nutritional habits through a nutritional intervention on Session-RPE and fatigue, variables that could be decreased for all training session and competition games because of an improvement of daily nutritional intake. Therefore, this work begins with an introduction that provides the conceptual framework of this research focused on the key role of nutrition in sport, as well as on the current nutritional recommendations for athletes and specifically for basketball players. In addition, previous nutritional interventions carried out with other athletes are described, as well as consequential modifications on their food pattern, coinciding with the first objective of the present study. Subsequently, RPE, Session-RPE and fatigue are analyzed, with focus on their correlation with physical workload, training intensity, sports performance and recovery. Finally, all the aforementioned aspects (nutritional intake, RPE and fatigue) were combined in order to know the current status of the relation between each other, this being the base for the second objective of this study. Subsequently, the objectives mentioned above are explained, continuing with the explanation of the methodology used in the study. The methodology consisted of a case-study design, carrying out a long term nutritional intervention with three professional basketball players (each player = one case study; n = 1), in order to adapt their nutritional intake to nutritional recommendations. At the same time, the individual response of each player to the intervention was analyzed for the two main objectives of the study. Each player completed a food diary (7 days; weighing food) in three moments: before, during and at the end of the intervention. In addition, the Session-RPE and fatigue were daily recorded throughout the study for all trainings (training with ball and resistance training) and competition games. At the same time, other potentially influential variables such as mood state and sleeping were daily controlled throughout the study. Data analysis consisted in descriptive statistics calculation for all the variables of the study, the comparison between nutritional intake (evaluated at different times) and nutritional recommendations and a non-parametric mean comparison between pre intervention and during intervention periods was made by Wilcoxon test (repeated measurements) for all variables too. Finally, the changes in nutritional intake, mood state and sleeping were correlated with the perceived exertion and fatigue through correctional study (Tau_b de Kendall). After the methodology, the study results and the associated discussion are presented. The discussion is based on the current scientific evidence that contributes to understand the relation between Session-RPE, fatigue and nutrition throughout the competitive season. The main findings and results analysis can be summarized as follows: 1) the three professional basketball players initially had inadequate nutritional habits and this clearly shows the need of a sports nutritionist in the coaching staff of professional teams; (2) the major deficiencies of the three players’ diet corresponded to a pronounced deficit of energy intake and carbohydrates consumption which were reduced with nutritional intervention; (3) the excessive intake of total fat, saturated fatty acids, ethanol and protein found in some cases were also adapted to the recommendations after the intervention; (4) Session-RPE mean and fatigue of a certain period of the competition season, could be decreased in an individual player by increasing his carbohydrates intake in the long term, if there are no relevant psycho-emotional disorders; (5) the behavior of the Session-RPE in competition games does not seem to be influenced by the nutritional factors modified in this study. They seem to depend much more on the variation of external non-controllable factors associated with the professional basketball games. Given these results, the different characteristics of each player and the diverse responses observed after the intervention in each individual for all the variables, reinforced the importance of the use of a case study design for research with elite athletes as well as personalized nutritional counselling. In the same way, the different responses obtained for RPE and fatigue in the long term for each player due to modification of nutritional habits, show that there is a dependence of such variables on the physical, psychosocial, emotional and contextual characteristics of each player. Therefore it is proposed that the rigorous control of the qualitative variables that seem to influence the RPE and fatigue in the long term, may facilitate the understanding of data and the determination of unknown factors that could influence these variables. Finally, because Session-RPE is a direct indicator of the internal load of training (psycho-physiological stress experienced by the athlete), the possible attenuation of Session-RPE through the improvement in nutritional habits, would allow to apply the planned external loads of training with less internal stress and better recovery between sessions, with a decrease in fatigue, despite of the advance of the season.