Reduction of NO by CO on Cu/ZrO(2)/Al(2)O(3) catalysts: Characterization and catalytic activities

ZrO(2), gamma-Al(2)O(3) and ZrO(2)/gamma-Al(2)O(3)-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H(2), Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO(2)/gamma-Al(2)O(3) matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO(2). Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO(2). (C) 2009 Published by Elsevier Ltd.

Effect of the manufacturing process on the interlaminar fracture toughness of 2/2 twill weave fabric carbon/epoxy composites

A 2/2 twill weave fabric carbon fibre reinforced epoxy matrix composite MTM56/CF0300 was used to investigate the effect of different manufacturing processes on the interlaminar fracture toughness. Double cantilever beam tests were performed on composites manufactured by hot press, autoclave and 'Quickstep' processes. The 'Quickstep' process was recently developed in Perth, Western Australia for the manufacture of advanced composite components. The values of the mode I critical strain energy release rate (G1d were compared and the results showed that the composite specimens manufactured by the autoclave and the 'Quickstep' process had much higher interlaminar fracture toughness than the specimen produced by the hot press. When compared to specimens manufactured by the hot press, the interlaminar fracture toughness values of the Quickstep and autoclave samples were 38% and 49% higher respectively. The 'Quickstep' process produced composite specimens that had comparable interlaminar fracture toughness to autoclave manufactured composites. Scanning electron microscopy (SEM) was employed to study the topography of the mode I interlaminar fracture surface and dynamic mechanical analysis (DMA) was performed to investigate the fibre/matrix interphase. SEM micrography and DMA spectra indicated that autoclave and 'Quickstep' produced composites with stronger fibre/matrix adhesion than hot press.

An experimental study of low velocity impact response in 2/2 twill weave composite laminates manufactured by a novel fabrication process

A novel fabrication process for advanced composite components—the QuicktepTM process was described. 2/2 twill weave MTM56/CF0300 carbon epoxy composite laminates were manufactured by the Quickstep and the autoclave processes. The response of these laminates to drop-weight low velocity impact at energy levels ranging from 5 to 30 J was investigated. It was found that the laminates fabricated by the Quickstep had better impact damage tolerance than those fabricated by the autoclave. Optical microscopy revealed extensive matrix fracture in the center of the backside of the autoclave laminates indicating the more brittle property of the epoxy matrix cured by the autoclave process. Interfacial shear strength (IFSS) for two composite systems were measured by micro–debond experiments. The MTM56/CF0300 material cured by the Quickstep showed stronger fibre matrix adhesion. Since the thickness and density of the impact targets produced by two processes were different, finite element analysis (FEA) was performed to study the effect of these factors on the impact response. The simulation results showed that the difference in thickness and density affects the stress distribution under impact loading. Higher thickness and lower density caused by processing lead to less endurance to drop weight impact loading. Therefore the better performance of Quickstep laminates under impact loading was not due to the thickness and density change, but resulted from stronger mechanical properties.

Equal channel angular pressing of metal matrix composites: effect on particle distribution and fracture toughness

An Al6061-20%Al₂O₃ powder metallurgy (PM) metal matrix composite (MMC) with a strongly clustered particle distribution is subjected to equal channel angular pressing (ECAP) at a temperature of 370 °C. The evolution of the homogeneity of the particle distribution in the material during ECAP is investigated by the quadrat method. The model proposed by Tan and Zhang [Mater Sci Eng 1998;244:80] for estimating the critical particle size which is required for a homogeneous particle distribution in PM MMCs is extended to the case of a combination of extrusion and ECAP. The applicability of the model to predict a homogeneity of the particle distribution after extrusion and ECAP is discussed. It is shown that ECAP leads to an increase of the  uniformity of the particle distribution and the fracture toughness.

Manufacturing influence on the delamination fracture behavior of the T800H/3900-2 carbon fiber reinforced polymer composites

'Torayca' T800H/3900-2 is the first material qualified on Boeing Material Specification (BMS 8-276) which utilizes the thermoplastic-particulate interlayer toughening technology. Two manufacturing processes, the autoclave process and the fast heating rated Quickstep™ process, were employed to cure this material. The Quickstep process is a unique composite production technology which utilizes the fast heat transfer rate of fluid to heat and cure polymer composite components. The manufacturing influence on the mode I delamination fracture toughness of laminates was investigated by performing double cantilever beam tests. The composite specimens fabricated by two processes exhibited dissimilar delamination resistance curves (R-curves) under mode I loading. The initial value of fracture toughness GIC-INIT was 564 J/m2 for the autoclave specimens and 527 J/m2 for the Quickstep specimens. However, the average propagation fracture toughness GIC-PROP was 783 J/m2 for the Quickstep specimens, which was 2.6 times of that for the autoclave specimens. The mechanism of fracture occurred during delamination was studied under scanning electron microscope (SEM). Three types of fracture were observed: the interlayer fracture, the interface fracture, and the intralaminar fracture. These three types of fracture played different roles in affecting the delamination resistance curves during the crack growth. More fiber bridging was found in the process of delamination for the Quickstep specimens. Better fiber/matrix adhesion was found in the Quickstep specimens by conducting indentation-debond tests.

Stability of 2-D characteristic polynomials

This paper derives some new conditions for the bivariate characteristic polynomial of an uncertain matrix to be very strict Hurwitz. The uncertainties are assumed of the structured and unstructured type. By using the two-dimensional (2-D) inverse Laplace transform, the bounds on the uncertainties are derived which will ensure that the bivariate characteristic polynomial to be very strict Hurwitz. Two numerical examples are given to illustrate the results.

Evaluation of selective growth in a Fe-2.8% Si single crystal using Rodrigues-Frank space

A Fe-2.8%Si single crystal was scratched in order to randomise the texture in the neighbourhood of the notch. Annealing resulted in recrystallization and grain growth starting from the deformed zone. Misorientations between the single crystal matrix and the grown grains were gathered and were studied in order to investigate the possibility for selective growth based on a specific misorientation. However, instead of studying the misorientation angle or axis profiles separately in a 1D or 2D projection a full misorientation analysis was carried out in the 3-dimensional Rodrigues-Frank misorientation space, which offers an unambiguous interpretation of the data because no features are hidden or masked by a projection. It is concluded that the selective growth phenomenon following the <110>26.5deg misorientation relationship is strongly supported by the gathered orientation data, after appropriately normalizing these data with respect to a random misorientation distribution.

Reduced Skeletal Muscle Uncoupling Protein-3 Content in Prediabetic Subjects and Type 2 Diabetic Patients: Restoration by Rosiglitazone Treatment

Context: The mitochondrial uncoupling protein-3 (UCP3) has been implicated in the protection of the mitochondrial matrix against lipid-induced mitochondrial damage. Recent evidence points toward mitochondrial aberrations as a major contributor to the development of insulin resistance and diabetes, and UCP3 is reduced in diabetes.
Objective: We compared skeletal muscle UCP3 protein levels in prediabetic subjects [i.e. impaired glucose tolerance (IGT)], diabetic patients, and healthy controls and examined whether rosiglitazone treatment was able to restore UCP3.
Patients, Design, Intervention: Ten middle-aged obese men with type 2 diabetes mellitus [age, 61.4 ± 3.1 yr; body mass index (BMI), 29.8 ± 2.9 kg/m2], nine IGT subjects (age, 59.0 ± 6.6 yr; BMI, 29.7 ± 3.0 kg/m2), and 10 age- and BMI-matched healthy controls (age, 57.3 ± 7.4 yr; BMI, 30.1 ± 3.9 kg/m2) participated in this study. After baseline comparisons, diabetic patients received rosiglitazone (2 x 4 mg/d) for 8 wk.
Main Outcome Measures: Muscle biopsies were sampled to determine UCP3 and mitochondrial protein (complex I–V) content.
Results: UCP3 protein content was significantly lower in prediabetic IGT subjects and in diabetic patients compared with healthy controls (39.0 ± 28.5, 47.2 ± 24.7, and 72.0 ± 23.7 arbitrary units, respectively; P < 0.05), whereas the levels of the mitochondrial protein complex I–V were similar between groups. Rosiglitazone treatment for 8 wk significantly increased insulin sensitivity and muscle UCP3 content (from 53.2 ± 29.9 to 66.3 ± 30.9 arbitrary units; P < 0.05).
Conclusion: We show that UCP3 protein content is reduced in prediabetic subjects and type 2 diabetic patients. Eight weeks of rosiglitazone treatment restores skeletal muscle UCP3 protein in diabetic patients.

Upregulated MT1-MMP/TIMP-2 axis in the TSU-Pr1-B1/B2 model of metastatic progression in transitional cell carcinoma of the bladder

Muscle invasive transitional cell carcinoma (TCC) of the bladder is associated with a high frequency of metastasis, resulting in poor prognosis for patients presenting with this disease. Models that capture and demonstrate step-wise enhancement of elements of the human metastatic cascade on a similar genetic background are useful research tools. We have utilized the transitional cell carcinoma cell line TSU-Pr1 to develop an in vivo experimental model of bladder TCC metastasis. TSU-Pr1 cells were inoculated into the left cardiac ventricle of SCID mice and the development of bone metastases was monitored using high resolution X-ray. Tumor tissue from a single bone lesion was excised and cultured in vitro to generate the TSU-Pr1-B1 subline. This cycle was repeated with the TSU-Pr1-B1 cells to generate the successive subline TSU-Pr1-B2. DNA profiling and karyotype analysis confirmed the genetic relationship of these three cell lines. In vitro, the growth rate of these cell lines was not significantly different. However, following intracardiac inoculation TSU-Pr1, TSU-Pr1-B1 and TSU-Pr1-B2 exhibited increasing metastatic potential with a concomitant decrease in time to the onset of radiologically detectable metastatic bone lesions. Significant elevations in the levels of mRNA expression of the matrix metalloproteases (MMPs) membrane type 1-MMP (MT1-MMP), MT2-MMP and MMP-9, and their inhibitor, tissue inhibitor of metalloprotease-2 (TIMP-2), across the progressively metastatic cell lines, were detected by quantitative PCR. Given the role of MT1-MMP and TIMP-2 in MMP-2 activation, and the upregulation of MMP-9, these data suggest an important role for matrix remodeling, particularly basement membrane, in this progression. The TSU-Pr1-B1/B2 model holds promise for further identification of important molecules.

Determination of sodium oxalate in Bayer process liquors using flow analysis with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection

The research was a detailed investigation into a challenging analytical chemistry problem for the alumina industry. The successful outcomes were derived through innovative reagent chemistry and novel instrumental development. The resultant methodology and instrumentation deployed on this most demanding sample matrix is more robust, reliable and less expensive than anything currently used in this industry worldwide.

Optimization of mixing parameters through a water model for metal matrix composites synthesis

The influence of the mixing parameters on the synthesis of Al–SiCp reinforced metal matrix composites (MMCs) by the stir casting technique is investigated through a water model. The effects of some important mixing parameters such as impeller blade angle, rotating speed, direction of impeller rotation and effect of baffles are investigated and optimized. The results have shown that the axial concentration variation of natural graphite during stirring in the presence of four vertical baffles is 1.0 wt% against in the absence of baffles it is increased to 2.3 wt%. The variations observed in natural graphite concentration in water during mixing are in close agreement with the earlier modeling and limited experimental studies reported on the real molten aluminum–SiC system. Semi-empirical correlations arrived at between the dimensionless numbers for stirred water – natural graphite slurries are Po = Re−0.0545 Fr−1.099 and Po = Re−0.0219 Fr−1.0382 for clockwise and counter clockwise rotation respectively.

Thermodynamics and kinetics of the formation of Al2 O3/ MgAl2O4/MgO in Al-Silica metal matrix composite

The formation of Al₂O₃, MgAl₂O₄, and MgO has been widely studied in different Al base metal matrix composites, but the studies on thermodynamic aspects of the Al₂O₃/ MgAl₂O₄/MgO phase equilibria have been limited to few systems such as Al/Al₂O₃ and Al/SiC. The present study analyzes the Al₂O₃/MgAl₂O₄ and MgAl₂O₄/MgO equilibria with respect to the temperature and the Mg content in Al/SiO2 system using an extended Miedema model. There is a linear and parabolic variation in Mg with respect to the temperature for MgAl₂O₄/MgO and Al₂O₃/MgAl₂O₄ equilibria, respectively, and the influence of Si and Cu in the two equilibria is not appreciable. The experimental verification has been limited to MgAl₂O₄/MgO equilibria due to the high Mg content (≥0.5 wt pct) required for composite processing. The study has been carried out on two varieties of Al/SiO₂ composites, i.e., Al/Silica gel and Al/Micro silica processed by liquid metallurgy route (stir casting route). MgO is found to be more stable compared to MgAl₂O₄ at Mg levels ≥5 and 1 wt pct in Al/Silica gel and Al/Micro silica composites, respectively, at 1073 K. MgO is also found to be more stable at lower Mg content (3 wt pct) in Al/Silica gel composite with decreasing particle size of silica gel from 180 micron to submicron and nanolevels. The MgO to MgAl₂O₄ transformation has taken place through a series of transition phases influenced by the different thermodynamic and kinetic parameters such as holding temperature, Mg concentration in the alloy, holding time, and silica particle size.

Computing the numerical scale of the linguistic term set for the 2-tuple fuzzy linguistic representation model

When using linguistic approaches to solve decision problems, we need the techniques for computing with words (CW). Together with the 2-tuple fuzzy linguistic representation models (i.e., the Herrera and Mart´ınez model and the Wang and Hao model), some computational techniques for CW are also developed. In this paper, we define the concept of numerical scale and extend the 2-tuple fuzzy linguistic representation models under the numerical scale.We find that the key of computational techniques
based on linguistic 2-tuples is to set suitable numerical scale with
the purpose of making transformations between linguistic 2-tuples
and numerical values. By defining the concept of the transitive
calibration matrix and its consistent index, this paper develops an optimization model to compute the numerical scale of the linguistic term set. The desired properties of the optimization model are also presented. Furthermore, we discuss how to construct the transitive calibration matrix for decision problems using linguistic preference relations and analyze the linkage between the consistent index of the transitive calibration matrix and one of the linguistic preference relations. The results in this paper are pretty helpful to complete the fuzzy 2-tuple representation models for CW.

Conducting composite using an immiscible polymer blend matrix

Carbon black (CB) fillers were used to study the feasibility of achieving multiple percolation using an immiscible (polar) polymer blend matrix. By tailoring the morphology of the insulating dual phase matrix it has been shown that the percolation threshold (Ф_c) can be reduced over single-phase matrices. Cocontinuity in the polymer matrix is important in reducing Ф_c by either preferentially isolating the conducting filler at the interface of the two phases or within one particular continuous phase of the matrix thereby forming a continuous conducting network within a continuous network (multiple percolation). Actual melt processing time has been found to influence the dispersion of the fillers and hence Ф_c. Polarity of the matrix as well as the processing method has also been found to influence the dispersion of the filler within the host polymer.

Mechanism of allosteric regulation of transglutaminase 2 by GTP

Allosteric regulation is a fundamental mechanism of biological control. Here, we investigated the allosteric mechanism by which GTP inhibits cross-linking activity of transglutaminase 2 (TG2), a multifunctional protein, with postulated roles in receptor signaling, extracellular matrix assembly, and apoptosis. Our findings indicate that at least two components are involved in functionally coupling the allosteric site and active center of TG2, namely (i) GTP binding to mask a conformationally destabilizing switch residue, Arg-579, and to facilitate interdomain interactions that promote adoption of a compact, catalytically inactive conformation and (ii) stabilization of the inactive conformation by an uncommon H bond between a cysteine (Cys-277, an active center residue) and a tyrosine (Tyr-516, a residue located on a loop of the p-barrel 1 domain that harborst he GTP-bindings ite). Although not essential for GTP-mediated inhibition of cross-linking, this H bond enhances the rate of formation of the inactive conformer.