On the time for fold surfaces to order during the crystallization of polyethylene from the melt and its dependence on molecular parameters

New experiments underpin the interpretation of the basic division in crystallization behaviour of polyethylene in terms of whether or not there is time for the fold surface to order before the next molecular layer is added at the growth front. For typical growth rates, in Regime 11, polyethylene lamellae form with disordered {001} fold surfaces then transform, with lamellar thickening and twisting, towards the more-ordered condition found for slower crystallization in Regime 1, in which lamellae form with and retain {201} fold surfaces. Several linear and linear-low-density polyethylenes have been used to show that, for the same polymer crystallized alone or in a blend, the growth rate at which the change in initial lamellar condition occurs is reasonably constant thereby supporting the concept of a specific time for surfaces to attain the ordered {201}) state. This specific time, in the range from milliseconds to seconds, increases with molecular length, and in linear-low-density polymer, for higher branch contents. (c) 2006 Elsevier Ltd. All rights reserved.

The method of predicate least squares refinement

Parameters to be determined in a least squares refinement calculation to fit a set of observed data may sometimes usefully be `predicated' to values obtained from some independent source, such as a theoretical calculation. An algorithm for achieving this in a least squares refinement calculation is described, which leaves the operator in full control of the weight that he may wish to attach to the predicate values of the parameters.

Genetic parameters and evaluations from single- and multiple-trait analysis of dairy cow fertility and milk production

Genetic parameters and breeding values for dairy cow fertility were estimated from 62 443 lactation records. Two-trait analysis of fertility and milk yield was investigated as a method to estimate fertility breeding values when culling or selection based on milk yield in early lactation determines presence or absence of fertility observations in later lactations. Fertility traits were calving interval, intervals from calving to first service, calving to conception and first to last service, conception success to first service and number of services per conception. Milk production traits were 305-day milk, fat and protein yield. For fertility traits, range of estimates of heritability (h(2)) was 0.012 to 0.028 and of permanent environmental variance (c(2)) was 0.016 to 0.032. Genetic correlations (r(g)) among fertility traits were generally high ( > 0.70). Genetic correlations of fertility with milk production traits were unfavourable (range -0.11 to 0.46). Single and two-trait analyses of fertility were compared using the same data set. The estimates of h(2) and c(2) were similar for two types of analyses. However, there were differences between estimated breeding values and rankings for the same trait from single versus multi-trait analyses. The range for rank correlation was 0.69-0.83 for all animals in the pedigree and 0.89-0.96 for sires with more than 25 daughters. As single-trait method is biased due to selection on milk yield, a multi-trait evaluation of fertility with milk yield is recommended. (C) 2002 Elsevier Science B.V. All rights reserved.

Near infrared reflectance spectroscopy (NIRS) to predict biological parameters of maize silage: effects of particle comminution, oven drying temperature and the presence of residual moisture

Maize silage nutritive quality is routinely determined by near infrared reflectance spectroscopy (NIRS). However, little is known about the impact of sample preparation on the accuracy of the calibration to predict biological traits. A sample population of 48 maize silages representing a wide range of physiological maturities was used in a study to determine the impact of different sample preparation procedures (i.e., drying regimes; the presence or absence of residual moisture; the degree of particle comminution) on resultant NIR prediction statistics. All silages were scanned using a total of 12 combinations of sample pre-treatments. Each sample preparation combination was subjected to three multivariate regression techniques to give a total of 36 predictions per biological trait. Increased sample preparations procedure, relative to scanning the unprocessed whole plant (WP) material, always resulted in a numerical minimisation of model statistics. However, the ability of each of the treatments to significantly minimise the model statistics differed. Particle comminution was the most important factor, oven-drying regime was intermediate, and residual moisture presence was the least important. Models to predict various biological parameters of maize silage will be improved if material is subjected to a high degree of particle comminution (i.e., having been passed through a 1 mm screen) and developed on plant material previously dried at 60 degrees C. The extra effort in terms of time and cost required to remove sample residual moisture cannot be justified. (c) 2005 Elsevier B.V. All rights reserved.

Using near infrared reflectance spectroscopy (NIRS) to predict the biological parameters of maize silage

The microbial fermentability, ruminal degradability and digestibility of 48 maize silages were determined using in vitro gas production (GP), in situ degradability and in vitro digestibility procedures. The silages were produced from forage maize harvested throughout the summer of 1998, and represent a wide range of physiological maturities. Large variations among samples were observed for all biological parameters, with the exception of in vitro digestibility and the asymptote of in vitro GP. The potential of near infrared reflectance spectroscopy (NIRS) to predict the biological parameters measured was determined by regression of the biological data against the respective spectral profile. NIRS demonstrated only a moderate ability (R-2 > 0.60-0.80) to predict in vitro digestibility, modelled kinetics of gas production (excluding the asymptote of gas production) and the modelled ruminally soluble dry matter (DM) fraction. Calibration statistics for remaining biological parameters were unacceptably poor (R-2 = 0.60). (C) 2004 Elsevier B.V. All rights reserved.

Influence of vegetation on the local climate and hydrology in the tropics: sensitivity to soil parameters

Land use change with accompanying major modifications to the vegetation cover is widespread in the tropics, due to increasing demands for agricultural land, and may have significant impacts on the climate. This study investigates (1) the influence of vegetation on the local climate in the tropics; (2) how that influence varies from region to region; and (3) how the sensitivity of the local climate to vegetation, and hence land use change, depends on the hydraulic characteristics of the soil. A series of idealised experiments with the Hadley Centre atmospheric model, HadAM3, are described in which the influence of vegetation in the tropics is assessed by comparing the results of integrations with and without tropical vegetation. The sensitivity of the results to the soil characteristics is then explored by repeating the experiments with a differing, but equally valid, description of soil hydraulic parameters. The results have shown that vegetation has a significant moderating effect on the climate throughout the tropics by cooling the surface through enhanced latent heat fluxes. The influence of vegetation is, however, seasonally dependent, with much greater impacts during the dry season when the availability of surface moisture is limited. Furthermore, there are significant regional variations both in terms of the magnitude of the cooling and in the response of the precipitation. Not all regions show a feedback of vegetation on the local precipitation; this result has been related both to vegetation type and to the prevailing meteorological conditions. An important finding has been the sensitivity of the results to the specification of the soil hydraulic parameters. The introduction of more freely draining soils has changed the soil-moisture contents of the control, vegetated system and has reduced, significantly, the climate sensitivity to vegetation and by implication, land use change. Changes to the soil parameters have also had an impact on the soil hydrology and its interaction with vegetation, by altering the partitioning between fast and slow runoff processes. These results raise important questions about the representation of highly heterogeneous soil characteristics in climate models, as well as the potential influence of land use change on the soil characteristics themselves.

Relationships between transition period diet, metabolic parameters and fertility in lactating dairy cows

Cows in severe negative energy balance after calving have reduced fertility, mediated by metabolic signals influencing the reproductive system. We hypothesised that transition diet could alter metabolic status after calving, and thus influence fertility. Multiparous dairy cows were assigned to four transition groups 6 weeks pre-calving and fed: (a) basal control diet (n = 10); (b) basal diet plus barley (STARCH, n = 10); (c) basal diet plus Soypass (high protein, HiPROT, n = 11); or (d) no transition management (NoTRANS, n = 9). All cows received the same lactational diet. Blood samples, body weights and condition scores (BCS) were collected weekly. Fertility parameters were monitored using milk progesterone profiles and were not affected by transition diet. Data from all cows were then combined and analysed according to the pattern of post-partum ovarian activity. Cows with low progesterone profiles had significantly lower insulin-like growth factor-I (IGF-I) and insulin concentrations accompanied by reduced dry matter intakes (DMIs), BCS and body weight. Cows with prolonged luteal activity (PLA) were older and tended to have lower IGF-I. Analysis based on the calving to conception interval revealed that cows which failed to conceive (9/40) also had reduced IGF-I, BCS and body weight. Fertility was, therefore, decreased in cows which were in poor metabolic status following calving. This was reflected in reduced circulating IGF-I concentrations and compromised both ovarian activity and conception. There was little effect of the transition diets on these parameters. (C) 2003 Elsevier Science Inc. All rights reserved.

Inter-laboratory variation of in vitro cumulative gas production profiles of feeds using manual and automated methods

A study was conducted to estimate variation among laboratories and between manual and automated techniques of measuring pressure on the resulting gas production profiles (GPP). Eight feeds (molassed sugarbeet feed, grass silage, maize silage, soyabean hulls, maize gluten feed, whole crop wheat silage, wheat, glucose) were milled to pass a I mm screen and sent to three laboratories (ADAS Nutritional Sciences Research Unit, UK; Institute of Grassland and Environmental Research (IGER), UK; Wageningen University, The Netherlands). Each laboratory measured GPP over 144 h using standardised procedures with manual pressure transducers (MPT) and automated pressure systems (APS). The APS at ADAS used a pressure transducer and bottles in a shaking water bath, while the APS at Wageningen and IGER used a pressure sensor and bottles held in a stationary rack. Apparent dry matter degradability (ADDM) was estimated at the end of the incubation. GPP were fitted to a modified Michaelis-Menten model assuming a single phase of gas production, and GPP were described in terms of the asymptotic volume of gas produced (A), the time to half A (B), the time of maximum gas production rate (t(RM) (gas)) and maximum gas production rate (R-M (gas)). There were effects (P<0.001) of substrate on all parameters. However, MPT produced more (P<0.001) gas, but with longer (P<0.001) B and t(RM gas) (P<0.05) and lower (P<0.001) R-M gas compared to APS. There was no difference between apparatus in ADDM estimates. Interactions occurred between substrate and apparatus, substrate and laboratory, and laboratory and apparatus. However, when mean values for MPT were regressed from the individual laboratories, relationships were good (i.e., adjusted R-2 = 0.827 or higher). Good relationships were also observed with APS, although they were weaker than for MPT (i.e., adjusted R-2 = 0.723 or higher). The relationships between mean MPT and mean APS data were also good (i.e., adjusted R 2 = 0. 844 or higher). Data suggest that, although laboratory and method of measuring pressure are sources of variation in GPP estimation, it should be possible using appropriate mathematical models to standardise data among laboratories so that data from one laboratory could be extrapolated to others. This would allow development of a database of GPP data from many diverse feeds. (c) 2005 Published by Elsevier B.V.

PopABC: a program to infer historical demographic parameters

PopABC is a computer package for inferring the pattern of demographic divergence of closely related populations and species. The software performs coalescent simulation in the framework of approximate Bayesian computation (ABC). PopABC can also be used to perform Bayesian model choice to discriminate between different demographic scenarios. The program can be used either for research or for education and teaching purposes.

Investigation of air quality, comfort parameters and effectiveness for two floor-level air supply systems in classrooms

The method of distributing the outdoor air in classrooms has a major impact on indoor air quality and thermal comfort of pupils. In a previous study, ([11] Karimipanah T, Sandberg M, Awbi HB. A comparative study of different air distribution systems in a classroom. In: Proceedings of Roomvent 2000, vol. II, Reading, UK, 2000. p. 1013-18; [13] Karimipanah T, Sandberg M, Awbi HB, Blomqvist C. Effectiveness of confluent jets ventilation system for classrooms. In: Idoor Air 2005, Beijing, China, 2005 (to be presented).) presented results for four and two types of air distribution systems tested in a purpose built classroom with simulated occupancy as well as computational fluid dynamics (CFD) modelling. In this paper, the same experimental setup has been used to investigate the indoor environment in the classroom using confluent jet ventilation, see also ([12]Cho YJ, Awbi HB, Karimipanah T. The characteristics of wall confluent jets for ventilated enclosures. In: Proceedings of Roomvent 2004, Coimbra, Portugal, 2004.) Measurements of air speed, air temperature and tracer gas concentrations have been carried out for different thermal conditions. In addition, 56 cases of CFD simulations have been carried to provide additional information on the indoor air quality and comfort conditions throughout the classroom, such as ventilation effectiveness, air exchange effectiveness, effect of flow rate, effect of radiation, effect of supply temperature, etc., and these are compared with measured data.