Dislocation characterization in crystals of potash alum grown by seeded solution growth under conditions of low supersaturation

An analysis has been carried out of the genesis and character of growth dislocations present in all growth sectors of single crystals of potash alum. The crystals, grown from seeded solutions by the temperature lowering method under conditions of low supersaturation, presented the well-developed forms: {111} dominant, {100} and {110}. Growth dislocations formed predominately during refacetting of the edges and corners of the seed, rounded during preparation and insertion into the supersaturated solution. From here they become refracted into the {111} sectors which proved to be the most defective. Smaller numbers of dislocations form at the {111}, {100} and {110} seed interfaces and propagate in these sectors. In crystals of inferior quality, a number of inclusions were found predominantly in the fast growing {100} sectors which become the source of additional dislocations. Dislocations present in the original seed did not propagate across the interface into the developing crystal. Dislocations of all characters were observed. The principal Burgers vectors were found to be left angle bracket100right-pointing angle bracket, left angle bracket110right-pointing angle bracket and left angle bracket111right-pointing angle bracket.

Jakojuuriviljelyn vaikutus kasvihuonekurkun (Cucumis sativus L.) kasvuun ja kehitykseen

Kasvit ottavat vettä parhaiten kasteluravinneliuoksesta, jonka ravinnepitoisuus on pieni. Intensiivisessä kasvihuonetuotannossa käytetään silti kastelulannoituksessa usein korkeita ravinnepitoisuuksia ravinnepuutosten ja satotappioiden välttämiseksi. Jakojuuriviljelyssä kasvin juuriston annetaan kasvaa kahteen erilliseen kasvualustaosioon. Tällöin toiselle puolelle annetaan johtokyvyltään väkevää ja toiselle puolelle laimeaa ravinneliuosta. Erityisesti kasvihuonekurkun, joka on herkkä kasvualustan suolaisuuden aiheuttamille vedensaantiongelmille, on todettu hyötyvän tästä tekniikasta, mikä näkyy kasvaneina satoina. Tämän MTT Piikkiössä toteutetun kasvihuonekurkun jakojuuriviljelytutkimuksen tavoitteena oli tarkentaa tekniikkaa erityisesti kasteluliuosten johtokyvyn osalta. Yhtenäisjuuriviljelyn ja perinteisen jakojuuriviljelyn lisäksi kokeessa oli kaksi jakojuuriviljelykäsittelyä, joissa ravinneliuosväkevyyksiä vaihdettiin väliajoin juuriston toimintakyvyn parantamiseksi. Erillisessä osakokeessa tutkittiin erilaisten johtokyky-yhdistelmien vaikutusta kasvihuonekurkun vegetatiiviseen kasvuun maanpäällisten ja -alaisten kasvinosien välillä sekä juurten morfologiaan ja anatomiaan. Tulokset osoittivat, että jakojuuriviljely lisäsi kasvihuonekurkun sadontuottoa jopa 16 %, mutta ei vaikuttanut koko viljelykauden veden tai ravinteiden ottoon. Yhtenäisjuuriviljelyssä muodostui eniten piikkikärkisiä hedelmiä, mikä viittaa vedensaantiongelmiin haihdutustarpeen ollessa suurin. Viljelytekniikalla ei ollut vaikutusta kasvien vegetatiiviseen kasvuun tai kasvuston rakenteeseen. Lehtiruodeista tehdyt nitraatti- ja kaliummittaukset osoittivat, ettei kasteluliuosten ravinnepitoisuuksilla ollut vaikutusta juurten ravinteiden ottoon. Erilaisilla johtokyky-yhdistelmillä oli huomattavampi vaikutus kasvihuonekurkun juurten painoon kuin verson painoon tai varren pituuskasvuun. Lehtiruotianalyysit viittasivat ravinteiden erilaiseen allokointiin eri johtokyky-yhdistelmissä. Korkeiden johtokykyjen aiheuttama osmoottinen stressi johti muutoksiin juurten morfologiassa ja anatomiassa. Tulosten perusteella jakojuuriviljely paransi kehittyvien hedelmien kohdevahvuutta suhteessa muihin kohteisiin vaikuttamatta vegetatiiviseen kasvuun. Kun laimean ja väkevän ravinneliuoksen puolia vaihdettiin, juuristo otti joustavasti vettä ja ravinteita olosuhteiden määräämästä edullisemmasta johtokyvystä, jolloin kasvihuonekurkun viljelyssä saavutettiin merkittävä satoetu. Juuriston jakaminen vaikuttanee kasvien hormoniaineenvaihduntaan ja voi heikentää juuriston kasvua heikentämättä sen toimintakykyä, jolloin yhteyttämistuotteita kohdennetaan tehokkaammin maanpäällisten osien kasvuun.

Coupled substitution of niobium and silicon in potassium titanyl phosphate and arsenate (KTiOPO4 and KTiOAsO4. Synthesis and nonlinear optical properties of KTi1-xNbxOX1-xSixO4 (X = P, As)

Coupled substitution of Nb(V) and Si(IV) for Ti(IV) and P(V)/As(V) in KTiOP04 (KTP) and KTiOAsO4 (KTA) giving new series of nonlinear optical materials, KTi1-xNbxOX1-xSixO4 (X=P,As), has been investigated. Substitution up to x = 0.40 readily occurs, the members retaining the orthorhombic (Pna2(1)) structure of KTP. The second harmonic generation (SHG) property of the parent KTP and KTA is not adversely affected by the coupled substitution. SHG intensity of the powder samples of the X = P series shows a slight increase with x up to x = 0.15; for 0.15 < x less-than-or-equal-to 0.40, there is a decrease in SHG intensity as compared to that for KTP. A similar trend in SHG intensity is seen for the arsenic analogs.

Electrical-Resistivity Studies on GE-SE Glasses at High-Pressures and Low-Temperatures

High pressure electrical resistivity measurements were carried out on GexSe100-x (0 less-than-or-equal-to x less-than-or-equal-to 40) glasses at ambient and low temperatures using the Bridgman anvil system. All the melt quenched glasses show a discontinuous glassy semiconductor to crystalline metal transition at high pressures. The high pressure phases of Ge-Se samples do not correspond to any of the equilibrium phases of the system. Additionally, the variation of transition pressure (P(T)), ambient resistivity (rho0) and the activation energy (DELTAE(t)) with composition, exhibit a change in behaviour at x = 20 and 33. The unusual variations observed in these glasses are discussed in the light of chemical and percolation thresholds occurring in the glassy system.

Magnetorotational instability driven dynamos at low magnetic Prandtl numbers

Numerical simulations of the magnetorotational instability (MRI) with zero initial net flux in a non-stratified isothermal cubic domain are used to demonstrate the importance of magnetic boundary conditions. In fully periodic systems the level of turbulence generated by the MRI strongly decreases as the magnetic Prandtl number (Pm), which is the ratio of kinematic viscosity and magnetic diffusion, is decreased. No MRI or dynamo action below Pm=1 is found, agreeing with earlier investigations. Using vertical field conditions, which allow magnetic helicity fluxes out of the system, the MRI is found to be excited in the range 0.1

Low frequency oscillations in power systems: A physical account and adaptive stabilizers

This paper presents a physical explanation of the phenomenon of low frequency oscillations experienced in power systems. A brief account of the present practice of providing fixed gain power system stabilizers (PSS) is followed by a summary of some of the recent design proposals for adaptive PSS. A novel PSS based on the effort of cancelling the negative damping torque produced by the automatic voltage regulator (AVR) is presented along with some recent studies on a multimachine system using a frequency identification technique.

Low-temperature preparation and characterization of phase-pure lanthanide chromates (V) by the citrate gel process

Phase-pure, crystalline lanthanide chromates LnCrO4 (V), where Ln = La, Pr, Nd, Sm, Gd, Dy, Ho, Yb, Lu and Y, have been prepared by the controlled combustion of the corresponding lanthanide biscitrato chromium (III) complexes at comparatively low temperatures. Formation of chromates (V) was confirmed by X-ray diffraction, infrared and electronic spectroscopy. Phase purity of the materials has also been confirmed by X-ray photoelectron spectroscopy.

Solubility of sulfur dioxide at low partial pressures in dilute sulfuric acid solutions

Equilibrium of dissolution of sulfur dioxide at ppm levels in aqueous solutions of dilute sulfuric acid is analyzed, and a general expression is derived relating the total concentration of sulfur dioxide in the liquid phase to the partial pressure of SO2 in the gas and to the concentration of sulfuric acid in the solution. The equation is simplified for zero and high concentrations of the acid. Experiments at high concentrations of sulfuric acid have enabled the direct determination of Henry’s constant and its dependency on temperature. Heat of dissolution is -31.47 kJ/mol. Experiments in the absence of sulfuric acid and the related simplified expression have led to the determination of the equilibrium constant of the hydrolysis of aqueous sulfur dioxide and its temperature dependency.The heat of hydrolysis is 15.69 kJ/mol. The model equation with these parameters predicts the experimental data of the present work as well as the reported data very well.

Structural refinement using high-resolution powder X-ray diffraction data of Ca0.5Ti2P3O12, a low-thermal-expansion material

The structures of Ca0.5Ti2P3O12 and Sr0.5Ti2P3O12, low-thermal-expansion materials, have been refined by the Rietveld method using high-resolution powder X-ray diffraction (XRD) data. The assignment of space group R[3 with combining macron] to NASICON-type compounds containing divalent cations is confirmed. 31P magic-angle spinning nuclear magnetic resonance (MASNMR) data are presented as supporting data. A comparison of changes in the polyhedral network resulting from the cation distribution, is made with NaTi2P3O12 and Nb2P3O12. Factors that may govern thermal expansion in this family of compounds are discussed.

Kinetic approach to dislocation bending in low-mobility films

A kinetic model has been developed for dislocation bending at the growth surface in compressively stressed low-mobility films such as III-V nitrides. It is based on a reduction in the number of atoms at the growth surface. Stress and nonstress sources of driving force for such a reduction are discussed. A comparison between the derived equations and experimentally measured stress evolution data yields good agreement between the predicted and observed angles through which dislocations bend.

Magnetically actuated propulsion at low Reynolds numbers: towards nanoscale control

Significant progress has been made in the fabrication of micron and sub-micron structures whose motion can be controlled in liquids under ambient conditions. The aim of many of these engineering endeavors is to be able to build and propel an artificial micro-structure that rivals the versatility of biological swimmers of similar size, e. g. motile bacterial cells. Applications for such artificial ``micro-bots'' are envisioned to range from microrheology to targeted drug delivery and microsurgery, and require full motion-control under ambient conditions. In this Mini-Review we discuss the construction, actuation, and operation of several devices that have recently been reported, especially systems that can be controlled by and propelled with homogenous magnetic fields. We describe the fabrication and associated experimental challenges and discuss potential applications.

Polyelectrolyte microcapsules for sustained delivery of water-soluble drugs

Polyelectrolyte capsules composed of weak polyelectrolytes are introduced as a simple and efficient system for spontaneous encapsulation of low molecular weight water-soluble drugs. Polyelectrolyte capsules were prepared by layer-by-layer (LbL) assembling of weak polyelectrolytes, poly(allylamine hydrochloride) (PAH) and poly (methacrylic acid) (PMA) on polystyrene sulfonate (PSS) doped CaCO3 particles followed by core removal with ethylene-diaminetetraacetic add (EDTA). The loading process was observed by confocal laser scanning microscopy (CLSM) using tetramethylrhodamineisothiocyanate labeled dextran (TRITC-dextran) as a fluorescent probe. The intensity of fluorescent probe inside the capsule decreased with increase in cross-linking time. Ciprofloxacin hydrochloride (a model water-soluble drug) was spontaneously deposited into PAH/PMA capsules and their morphological changes were investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The quantitative study of drug loading was also elucidated which showed that drug loading increased with initial drug concentration, but decreased with increase in pH. The loaded drug was released in a sustained manner for 6 h, which could be further extended by cross-linking the capsule wall. The released drug showed significant antibacterial activity against E. coli. These findings indicate that such capsules can be potential carriers for water-soluble drugs in sustained/controlled drug delivery applications. (C) 2010 Elsevier B.V. All rights reserved.

A numerical investigation of ductile fracture initiation in a high-strength low-alloy steel

In this work, static and drop-weight impact experiments, which have been conducted using three-point bend fracture specimens of a high-strength low-alloy steel, are analysed by performing finite-element simulations. The Gurson constitutive model that accounts for the ductile failure mechanisms of microvoid nucleation, growth and is employed within the framework of a finite deformation plasticity theory. Two populations of second-phase particles are considered, including large inclusions which initiate voids at an early stage and small particles which require large strains to nucleate voids. The most important objective of the work is to assess quantitatively the effects of material inertia, strain rate sensitivity and local adiabatic temperature rise (due to conversion of plastic work into heat) on dynamic ductile crack initiation. This is accomplished by comparing the evolution histories of void volume fraction near the notch tip in the static analysis with the dynamic analyses. The results indicate that increased strain hardening caused by strain rate sensitivity, which becomes important under dynamic loading, plays a benign role in considerably slowing down the void growth rate near the notch tip. This is partially opposed by thermal softening caused by adiabatic heating near the notch tip.