Utilisation of vegetable leaves for carp production

The results of two sets of experiments on mono-culture of grass carp (Ctenopharyngodon idella) and mixed culture of carps (grass carp 50 : catla 20 : rohu 15 : mrigal 15) fed exclusively with vegetable leaves are reported. The experiments were conducted with two replicates each in 0.02 ha ponds of Wastewater Aquaculture Division of the Central Institute of Freshwater Aquaculture, Rahara during 1991-93. Monoculture of grass carp stocked at 1000/ha demonstrated an average net production of 21.0 kg/ 0.02 ha/8 months (1501 kg/ha/yr). Mixed culture of carps stocked at 5000 /ha recorded an average net production of 22.5 kg/0.02 ha/8 months (1903.7 kg/ha/yr). Field studies revealed that water bind weed (Ipomoea aquatica) is the most preferred feed of grass carp amongst vegetable leaves followed by amaranths (Amaranthus gangeticus and Amaranthus viridis), cauliflower (Brassica oleracia var. votrytis) and cabbage (Brassica oleracia var. capitata) leaves. Through selection of highly productive leaf vegetables and suitable crop planning on fallow fish pond dykes, round the year feeding programme of grass carp has been explored. Recycling of sewage effluent for vegetable production and utilisation of vegetable leaves for fish production is considered an ideal way of integrated resource management for low cost production.

Studies on paddy-cum-fish culture under different land situations

Paddy fields can be broadly classified on the basis of land situations viz. Upland - Shallow water (10-30 cm), Medium land-medium deepwater (30-100 cm) and Low land-deepwater (above 100 cm). Three major systems of paddy-cum-fish culture, viz. (A) high yielding paddy varieties (H.Y.V) and air-breathing fish under Upland, (B) H.Y.V./local paddy and Tilapia/common carp under Medium land and (C) deepwater paddy and major Indian carps under Low land situations have been successfully investigated in the farmers' fields and at the Research Stations (1982-92). Effects of low-cost artificial feeding on growth, yield and management practices of different types of fish showed a considerable increase of rice and fish yields and a decrease in insect-pest incidence. Under Upland situation, short duration H.Y.V. in combination with fast-growing air breathing fish was studied thrice a year (summer, winter & autumn seasons). Combined rice and fish culture produced highest yields in all the seasons than in the control.

Nanostructuring of materials for device and sensor applications

The recent developments in nanotechnology are reviewed, with particular emphasis on its application in microsystem technology where increased reliability is achieved by integrating the sensor and the readout electronics on the same substrate. New applications may be possible using integrated micromechanical clips to connect optic fibers and components in integrated silicon systems. Some of the key developments in enabling technologies are also described, including the control of thin film deposition, nanostructuring to tailor the properties of thin film, silicon micromachining to make sensors, and microclips for the low-cost assembly of integrated optical microsystems.

Hybrid potential flow-streamtube method for modelling VAWT-flowfield interactions

When designing vertical-axis wind turbines (VAWTs) for deployment in the urban environment, it is desirable to have a low-cost computational model that allows for modelling the coupled interaction of the turbine with the flowfleld. Such a method is presented in this paper, It combines a variation of the multiple streamtube model with a potential method to model flowfleld interactions. A method referred to as "streamtube surgery" is used to couple the influence of the flowfleld with the performance model of the VAWT. This tool is used to explore the instantaneous and cycle-averaged flowflelds of VAWTs. It can also be used to evaluate the influence on performance of multiple VAWTs in dense arrays or to quantify blockage effects of a VAWT in wind tunnel testing.

Parameter measurement for heavy-vehicle fuel consumption modelling

A mathematical model is developed to predict the energy consumption of a heavy vehicle. It includes the important factors of heavy-vehicle energy consumption, namely engine and drivetrain performances, losses due to accessories, aerodynamic drag, rolling resistance, road gradients, and driver behaviour. Novel low-cost testing methods were developed to determine engine and drivetrain characteristics. A simple drive cycle was used to validate the model. The model is able to predict the fuel use for a 371 tractor-semitrailer vehicle over a 4 km drive cycle within 1 per cent. This paper demonstrates that accurate and reliable vehicle benchmarking and model parameter measurement can be achieved without expensive equipment overheads, e.g. engine and chassis dynamometers.

Suitable sites for sustainable aquaculture development in Mymensingh, Bangladesh: A GIS methodological perspective

A GIS study was carried out to find out the sites suitable for aquaculture in Mymensingh region. A number of criteria were selected for GIS modeling followed by the approach of Kapetsky (1994). The criteria were developed from a range of existing data sources such as, surface and underground water level, availability of feed ingredients and animal wastes, sources of fish fry, market facilities, extension support and communication facilities for aquaculture development. The data were located, collected and compiled from different GOs and NGOs located in the region along with primary data from the field survey wherever necessary and then prepared for computer analyses. Using the database, a series of GIS models were developed in order to ascertain and prioritize the most suitable areas for aquaculture development in the region. Out of total 407,528 ha available lands in the region, the study identified 99,415 ha very suitable and 302,754 ha moderately suitable for aquaculture promotion. Result of the study is indicative to the modeling power of GIS for aquaculture application and could be used to refine the models in future, particularly if it is supported with further detail field data. To get a more concrete and complete model, detailed study should be made available on the availability of mustard oil cake, rice bran, wheat bran, and usable animal and urban wastes that could be used as low-cost feed for sustainable aquaculture.

Monoculture of three native air breathing fishes in homestead ditches and plastic barrels

Six on-farm trials were conducted from 1 August to 23 November 2004 in two different environments such as homestead ditches (10 to 17 square meters) and plastic barrels (240 liters) to develop techniques for nonoculture [sic] of climbing perch, Anabas testudineus, stinging catfish, Heteropneustes fossilis and walking catfish, Clarias batrachus for poor and landless people who have no access to pond. Stocking density for ditch was 10 fry/square meter while that for barrel was 20 fry/cubic meter. The fishes were fed with 3-test diets viz. low-cost formulated feed (rice bran 20%, wheat meal 10%, mustered [sic] oil cake 35%, poultry offal 35%), live foods (chopped snails and clams), and a commercial feed (Saudi-Bangla feed, starter 3: first month and grower-1: subsequent two months) and designated as T1, T2 and T3, respectively. Feeding rate was the same in all the treatments viz. 10% of body weight (first two months), 8% (third month) and 6% (fourth month). T1 and T2 had three replications while T3 had two replications. Water temperature was recorded weekly while fish growth was monitored monthly. After 4 months' rearing, H. fossilis and C. batrachus in ditches and barrels attained higher average weight in T2 followed by T3 and T1 while A. testudineus in barrels also attained higher average weight in T2. The variation in net weight gain by A. testudineus in ditch fed test diets T2 and T3 was not significantly different (P>0.05) though the net gain in both T2 and T3 was significantly (P<0.05) higher than that of T1. The yield of climbing perch as obtained from T1, T2 and T3 was 988, 1136 and 1185 kg/ha, respectively while that stinging catfish was 395, 242 and 444 kg/ha and walking catfish was 1605, 2,099 and 1,654 kg/ha respectively. All the three species showed significantly lower growth rate in barrels than in ditches.

A high temperature SOI CMOS NO2 sensor

For more than 20 years researchers have been interested in developing micro-gas sensors based on silicon technology. Most of the reported devices are based on micro-hotplates, however they use materials that are not CMOS compatible, and therefore are not suitable for large volume manufacturing. Furthermore, they do not allow the circuitry to be integrated on to the chip. CMOS compatible devices have been previously reported. However, these use polysilicon as the heater material, which has long term stability problems at high temperatures. Here we present low power, low cost SOI CMOS NO2 sensors, based on high stability single crystal silicon P+ micro-heaters platforms, capable of measuring gas concentrations down to 0.1 ppm. We have integrated a thin tungsten molybdenum oxide layer as a sensing material with a foundry-standard SOI CMOS micro-hotplate and tested this to NO2. We believe these devices have the potential for use as robust, very low power consumption, low cost gas sensors. © 2011 American Institute of Physics.

Wavelength-tuneable liquid crystal lasers from the visible to the near-infrared

The study of band-edge lasing from dye-doped chiral nematic liquid crystals has thus far been largely restricted to visible wavelengths. In this paper, a wide range of commercially available laser dyes are examined for their suitability as infrared emitters within a chiral nematic host. Problems such as poor solubility and reduced quantum efficiencies are overcome, and successful band-edge lasing is demonstrated within the range of 735-850 nm, using the dyes LD800, HITC-P and DOTC-P. This paper also reports on progress towards widely tuneable liquid crystal lasers, capable of emission in the region 460- 850 nm. Key to this is the use of common pump source, capable of simultaneously exciting all of the dyes (both infrared and visible) that are present within the system. Towards this aim, we successfully demonstrate near-infrared lasing (800 nm) facilitated by Förster energy transfer between the visible dye DCM, and the infra-red dye LD800, enabling pump wavelengths anywhere between 420 and 532 nm to be used. These results demonstrate that small and low-cost tuneable visible to near-infrared laser sources are achievable, using a single common pump source. Such devices are envisaged to have wide-ranging applications including medical imaging (including optical coherence tomography), point-of-care optical medical diagnostics (such as flow cytometry), telecommunications, and optical signatures for security coatings. © 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Thermal insulation boards from coconut pith

Processing technique and physical characteristics of thermal insulation boards prepared from coconut pith using rubber latex as the binding agent are reported in this communication. In view of the easy processing, low cost and comparable physical properties with other insulating materials available indigenously, manufacture of these boards appears to be promising.

Quo vadis, shrimp?

The paper discusses the shrimp culture practices of Thailand, the top producing country of cultured shrimp. These shrimp culture techniques include the use of reservoirs for better waste management, utilization of undiluted seawater for culture, low-cost pumping systems, measures to neutralize acid sulfate soils, proper treatment of pond bottom, and solutions to disease problems.

Adaptively modulated optical OFDM modems utilizing RSOAs as intensity modulators in IMDD SMF transmission systems.

Detailed investigations of the transmission performance of adaptively modulated optical orthogonal frequency division multiplexed (AMOOFDM) signals converted using reflective semiconductor optical amplifiers (RSOAs) are undertaken over intensity-modulation and direct-detection (IMDD) single-mode fiber (SMF) transmission systems for WDM-PONs. The theoretical RSOA model adopted for modulating the AMOOFDM signals is experimentally verified rigorously in the aforementioned transmission systems incorporating recently developed real-time end-to-end OOFDM transceivers. Extensive performance comparisons are also made between RSOA and SOA intensity modulators. Optimum RSOA operating conditions are identified, which are independent of RSOA rear-facet reflectivity and very similar to those corresponding to SOAs. Under the identified optimum operating conditions, the RSOA and SOA intensity modulators support the identical AMOOFDM transmission performance of 30Gb/s over 60km SMFs. Under low-cost optical component-enabled practical operating conditions, RSOA intensity modulators with rear-facet reflectivity values of >0.3 outperform considerably SOA intensity modulators in transmission performance, which decreases significantly with reducing RSOA rear-facet reflectivity and optical input power. In addition, results also show that use can be made of the RSOA/SOA intensity modulation-induced negative frequency chirp to improve the AMOOFDM transmission performance in IMDD SMF systems.

Air stable complementary polymer circuits fabricated in ambient condition by inkjet printing

Air stable complementary polymer inverters were demonstrated by inkjet printing of both top-gate electrodes and the semiconductors in ambient conditions. The p-type and n-type polymer semiconductors were also thermally annealed in ambient conditions after printing. The good performance of circuits in ambient condition shows that the transistors are not only air-stable in term of ambient humidity and oxygen, but also inert to ion migration through dielectrics from the printed gate. The result obtained here has further confirmed the feasibility of fabrication of low-cost polymer complementary circuits in a practical environment. © 2011 Elsevier B.V. All rights reserved.

Imbibition dynamics of nano-particulate ink-jet drops on micro-porous media

Ink-jet printing of nano-metallic colloidal fluids on to porous media such as coated papers has become a viable method to produce conductive tracks for low-cost, disposable printed electronic devices. However, the formation of well-defined and functional tracks on an absorbing surface is controlled by the drop imbibition dynamics in addition to the well-studied post-impact drop spreading behavior. This study represents the first investigation of the real-time imbibition of ink-jet deposited nano-Cu colloid drops on to coated paper substrates. In addition, the same ink was deposited on to a non-porous polymer surface as a control substrate. By using high-speed video imaging to capture the deposition of ink-jet drops, the time-scales of drop spreading and imbibition were quantified and compared with model predictions. The influences of the coating pore size on the bulk absorption rate and nano-Cu particle distribution have also been studied.

Preliminary observations on cage culture of Tilapia esculenta Graham and Tilapia xillii (Gervais) in Lake Victoria waters, at the Freshwater Fisheries Institute, Nyegezi, Tanzania

Cage culture of Tilapia is not suggested as a substitute for any known techniques in fish culture, but as one of the various techniques of obtaining more fish under controlled conditions. This fact has been very well accepted in various countries. Whererever facilities exist, this line of fish culture should be vigorously explored as a possible avenue in increasing fish production. High density stocking, management under controlled conditions, easy technique of fabricating the cage at relatively low cost, having no demand on land area, absence of prolific and effective breeding and easy availability of fish when a person needs it are a few of the attractions of the technique. The studies indicate that it is desirable to have different meshes for the cages, such as, small meshed cages for rearing fry to fingerlings stages, and larger meshed cages for rearing fingerlings to table sized fishes. II' the meshes are small, the resistance will be more and less water wilt pass through. While feeding with powdered food material, because of brisk activity of feeding fish, a part of the feed appeared wasted. This can be easily overcome if we would resort to feeding fish with cheap pelleted feeds which will no doubt reduce wastage. Precaution has to be taken against damage of the net and thereby loss of fish and against poaching by unauthorised persons. In the present attempt has been demonstrated the possibility of utilizing locally available species of Tilapia for cage culture and obtaining moderately satisfactory growth rates.