Water distribuition characteristics and soil loss of LEPA Quad-Spray emitter nozzles

The objective of this study was to characterize water application rate, water application pattern width, flow rate, water distribution uniformity and soil loss caused by nozzles of the Low Energy Precision Aplication (LEPA) type Quad-Spray emitter. The study was carried out at the Hydraulic and Irrigation Laboratory of the Department of Engineering at the Federal University of Lavras, in Lavras, state of Minas Gerais - MG, Brazil. Twenty-two (22) LEPA Quad-Spray emitter nozzles were evaluated, with nozzle diameter ranging from 1.59 to 9.92 mm. The experimental design used was entirely randomized, with three replications.Increasing values of nozzle flow rate ranging from 77.44 up to 3,044 L h-1, were obtained with increasing nozzle diameter sizes. Application pattern width ranged from 0.56 up to 3.24m, according to nozzles diameter size. Low values of CDU (maximum of 35.73%) were observed when using the Quad-Spray nozzles. Observed average water application rates covered the range between 68.05 mm h-1 (the lowest value that was obtained with the 2.38mm nozzle) and 258.15 mm h-1 (the highest value that was observed with the 9.92 mm). Average water application rates increased in a simple non-linear function with the increase of nozzle size diameter. However, the weighted average increase in the amount of soil loss by erosion was not related to the increase of weighted average water application values.

Silting in the dense reservoir network of the Pereira de Miranda catchment

This study aims to analyze the impacts of the reservoir network within Pereira de Miranda - CE catchment (also called Pentecoste) over sediment transport and storage capacity of the system. The survey of the "damming" was carried out using satellite images. We identified 502 erosion units, derived from overlaying maps of the Universal Soil Loss Equation parameters, which allowed the estimation of localized erosion in the basin and identification of areas potentially generating sediment. In order to estimate silting in Pentecoste reservoir, different system structure scenarios were considered. An average erosion rate of 59 t ha-1year-1 was estimated. According to the model, the silting of Pentecoste reservoir may vary from 1.1 to 2.6% per decade, depending on the scenario considered. It is also observed that the reservoirs upstream can retain up to 58% of the sediment that would reach the Pentecoste reservoir. Very small reservoirs with a capacity of up to 100,000 m³, although representing only 1.83% of the system water availability, are able to retain almost 8% of total sediment produced.

Evaluation of sediment production and siltation in a small earth dam in Fernandópolis, SP

The siltation is a natural process, but can be accelerated by human actions and results in major problems for the reservoirs, reducing its useful volume for irrigation. An example of this problem was the reduction of the area of mirror water of Fernandópolis municipal dam in 48.3% during 20 years. Therefore, this study aimed to evaluate the production of sediments and siltation of Fernandópolis municipal dam from a methodology that can be applied to small earth dams for agricultural purposes. For this, it was monitored, monthly throughout the year, the volume of sediment deposited in the reservoir. The percentage of retention sediment in Fernandópolis municipal dam ranged from 53.9 to 94.5%, that associated with a high specific sediment yield, will cause its full silting in at most 57 years. It is recommended to minimize this process the restoration of permanent preservation areas and the removal of 17,500 m³ of sediment from the riverbed of the dam.

Hemosuccus pancreaticus: causa rara de hemorragia digestiva maciça

Hemosuccus pancreaticus is a unusual syndrome manifested by hemorrhage into the pancreatic duct and by blood loss through the ampulla of Vater: It may be caused by tumors, arteriovenous malformation, pancreatic lithiasis, aneurism rupture from adjacent vessels, or erosion of pancreatic and peripancreatic vessels due to chronic pancreatitis. The authors describe a case of massive and recurrent gastrointestinal upper hemorrhage in a 26-year-old man without known risk factors for pancreatitis. This man underwent urgent surgery due to gastrointestinal bleeding during the ínvestigation. During the procedure, blood was found in the intestinal lumen and a tumor in the head of pancreas with two centimeters of diameter: A gastroduodenopancreatectomy was performed. Histological study showed chronic pancreatitis with a fistula from the pancreatic vessels to the Wirsung duct. The patient was discharged without postoperative complications and after months, remains assymptomatic.

People and the intertidal : human induced changes, biodiversity loss, livelihood implications and management in the Western Indian Ocean

Vad händer i tidvattenzonen? Var går gränsen mellan land och hav, vad händer i tidvattenzonen och vem ansvarar för detta? I västra Indiska oceanen (VIO) kan avståndet mellan den lägsta nivån för lågvattnet och den högsta nivån för högvattnet vara flera kilometer och nivåskillnaderna upp till 6 meter och detta skapar ett stort och föränderligt område. Syftet med min avhandling är att öka förståelsen för tidvattenzonen i tropiska och subtropiska västra Indiska oceanen. Sammanfattningsvis visar mina studier att det finns ett mycket stort värde i den komplexa tidvattenzonen, men också att det här området hotas från både land och hav, genom t.ex. överexploatering, erosion och föroreningar. Uttnyttjandet av tidvattenzonen är stort och min avhandling har visat att aktiviteter såsom fiske i form av plocking av musslor och andra ryggradslösa djur och hamnaktiviteter påverkar den biologiska mångfalden negativt, vilket leder till försämrad levnadsstandard för resursutnyttjande människor i regionen. För att förbättra situationen krävs det mer forskning, miljöövervakning och bättre förvaltning av tidvattenzonen. Experter i regionen har rangordnat förslag på förvaltningsstrategier som skulle kunna testas för att förbättra miljön och skapa ett mer hållbart nyttjande. Avhandlingen visar även att det är möjligt att använda fjärranalysteknik såsom satellitbildsanalys för att kvantifiera mängden sjögräsvegetation (i form av biomassa), vilket kan ha stor betydelse för att förbättra storskalig miljöövervakning av kustnära naturtyper (habitat). I avhandlingsarbetet har jag använt mig av ett multidisciplinärt tillvägagångssätt och använt metoder såsom ekologisk och biologisk provtagning, intervjuer, observationer, diskussionsgrupper, frågeformulär och fjärranalys. Resultaten presenterade i denna avhandling ger en ökad kunskap om tidvattenzonen i utvecklingsländerna inom VIO-regionen som kan användas för att initiera och fortsätta att utveckla hållbara förvaltningsstrategier av biologiska resurser.

Element speciation and behaviour in metal-rich Boreal river and estuarine systems using ultrafiltration and chemical modelling

The bioavailability of metals and their potential for environmental pollution depends not simply on total concentrations, but is to a great extent determined by their chemical form. Consequently, knowledge of aqueous metal species is essential in investigating potential metal toxicity and mobility. The overall aim of this thesis is, thus, to determine the species of major and trace elements and the size distribution among the different forms (e.g. ions, molecules and mineral particles) in selected metal-enriched Boreal river and estuarine systems by utilising filtration techniques and geochemical modelling. On the basis of the spatial physicochemical patterns found, the fractionation and complexation processes of elements (mainly related to input of humic matter and pH-change) were examined. Dissolved (<1 kDa), colloidal (1 kDa-0.45 μm) and particulate (>0.45 μm) size fractions of sulfate, organic carbon (OC) and 44 metals/metalloids were investigated in the extremely acidic Vörå River system and its estuary in W Finland, and in four river systems in SW Finland (Sirppujoki, Laajoki, Mynäjoki and Paimionjoki), largely affected by soil erosion and acid sulfate (AS) soils. In addition, geochemical modelling was used to predict the formation of free ions and complexes in these investigated waters. One of the most important findings of this study is that the very large amounts of metals known to be released from AS soils (including Al, Ca, Cd, Co, Cu, Mg, Mn, Na, Ni, Si, U and the lanthanoids) occur and can prevail mainly in toxic forms throughout acidic river systems; as free ions and/or sulfate-complexes. This has serious effects on the biota and especially dissolved Al is expected to have acute effects on fish and other organisms, but also other potentially toxic dissolved elements (e.g. Cd, Cu, Mn and Ni) can have fatal effects on the biota in these environments. In upstream areas that are generally relatively forested (higher pH and contents of OC) fewer bioavailable elements (including Al, Cu, Ni and U) may be found due to complexation with the more abundantly occurring colloidal OC. In the rivers in SW Finland total metal concentrations were relatively high, but most of the elements occurred largely in a colloidal or particulate form and even elements expected to be very soluble (Ca, K, Mg, Na and Sr) occurred to a large extent in colloidal form. According to geochemical modelling, these patterns may only to a limited extent be explained by in-stream metal complexation/adsorption. Instead there were strong indications that the high metal concentrations and dominant solid fractions were largely caused by erosion of metal bearing phyllosilicates. A strong influence of AS soils, known to exist in the catchment, could be clearly distinguished in the Sirppujoki River as it had very high concentrations of a metal sequence typical of AS soils in a dissolved form (Ba, Br, Ca, Cd, Co, K, Mg, Mn, Na, Ni, Rb and Sr). In the Paimionjoki River, metal concentrations (including Ba, Cs, Fe, Hf, Pb, Rb, Si, Th, Ti, Tl and V; not typical of AS soils in the area) were high, but it was found that the main cause of this was erosion of metal bearing phyllosilicates and thus these metals occurred dominantly in less toxic colloidal and particulate fractions. In the two nearby rivers (Laajoki and Mynäjoki) there was influence of AS soils, but it was largely masked by eroded phyllosilicates. Consequently, rivers draining clay plains sensitive to erosion, like those in SW Finland, have generally high background metal concentrations due to erosion. Thus, relying on only semi-dissolved (<0.45 μm) concentrations obtained in routine monitoring, or geochemical modelling based on such data, can lead to a great overestimation of the water toxicity in this environment. The potentially toxic elements that are of concern in AS soil areas will ultimately be precipitated in the recipient estuary or sea, where the acidic metalrich river water will gradually be diluted/neutralised with brackish seawater. Along such a rising pH gradient Al, Cu and U will precipitate first together with organic matter closest to the river mouth. Manganese is relatively persistent in solution and, thus, precipitates further down the estuary as Mn oxides together with elements such as Ba, Cd, Co, Cu and Ni. Iron oxides, on the contrary, are not important scavengers of metals in the estuary, they are predicted to be associated only with As and PO4.

Ohkolanjoen valuma-alueen suojavyöhykkeiden yleissuunnitelma

Vantaanjoen vesistöalueella sijaitsevan Ohkolanjoen valuma-alueella laadittiin maatalousalueiden suojavyöhykkeiden yleissuunnitelma syksyllä 2010. Kartoituksessa löytyneet kohteet sisällytettiin yleissuunnitelmaan karttojen muodossa. Suojavyöhykkeet pidättävät tehokkaasti maatalousmaalta vesistöön kulkeutuvia ravinteita ja kiintoainesta. Maisemallisesti suojavyöhykkeet elävöittävät ympäristöä ja edistävät luonnon monimuotoisuutta maatalousalueilla. Suojavyöhykkeitä voidaan perustaa vesistöön tai valtaojaan rajoittuville tai tulvaherkille pelloille, sekä pohjavesialueille. Suojavyöhyke perustetaan ympäristötukikelpoiselle lohkolle ja tukea hakevan viljelijän täytyy olla sitoutunut ympäristötukeen. Yleissuunnittelun tavoitteena on löytää ne kohteet, joissa suojavyöhykkeistä olisi eniten hyötyä vesiensuojelun kannalta. Huomioon on otettu myös maisemalliset arvot ja luonnon monimuotoisuus. Suojavyöhykkeiden perustamiseen voi hakea maatalouden ympäristötuen erityistukea. Yleissuunnitelmassa esitetyt kohteet ovat suosituksia, maatalouden erityistukien hakeminen on aina vapaaehtoista. Ohkolanjoen valuma-alueen yleissuunnitelmassa esitetään suojavyöhykesuositusta yhteensä 25,7 kilometrin matkalle. Tästä erittäin tarpeellisia on 11,4 km ja tarpeellisia 14,3 km. Pohjavesialueella peltoa on vain vähän.

Degenerative joint disease in cattle and buffaloes in the Amazon region: a retrospective study

A retrospective study of the epidemiological and clinic-pathological aspects of cattle and buffaloes with degenerative joint disease (DJD) was conducted in the state of Pará, Brazil. From 1999 to 2014, eleven cattle and 24 buffaloes were evaluated. All the treated animals with suspected DJD underwent a clinical examination of the musculoskeletal system. In seven cattle and eight buffaloes with clinical signs of the disease postmortem examination was performed. The common clinical signs observed in both species were chronic lameness, stiff gait, postural changes, audible crackles in the affected limb, prolonged recumbency, difficulty in getting up and progressive weight loss. The lesions observed at necropsy were: irregular articular surfaces, erosion of the articular cartilage and the underlying bone tissue, and proliferation of the periarticular bone tissue with formation of osteophytes. The most affected joints in cattle and buffaloes wereof the hind limb. In buffaloes, the main predisposing factor to the onset of DJD was phosphorus deficiency. In cattle, defects of the anatomical conformation of the hind limbs, chronic trauma due to the activities performed, such as semen collection, and advanced age possibly contributed to the emergence of the disease.

Model-based estimation of liquid flows in the blast furnace hearth and taphole

This thesis presents a set of methods and models for estimation of iron and slag flows in the blast furnace hearth and taphole. The main focus was put on predicting taphole flow patterns and estimating the effects of various taphole conditions on the drainage behavior of the blast furnace hearth. All models were based on a general understanding of the typical tap cycle of an industrial blast furnace. Some of the models were evaluated on short-term process data from the reference furnace. A computational fluid dynamics (CFD) model was built and applied to simulate the complicated hearth flows and thus to predict the regions of the hearth exerted to erosion under various operating conditions. Key boundary variables of the CFD model were provided by a simplified drainage model based on the first principles. By examining the evolutions of liquid outflow rates measured from the furnace studied, the drainage model was improved to include the effects of taphole diameter and length. The estimated slag delays showed good agreement with the observed ones. The liquid flows in the taphole were further studied using two different models and the results of both models indicated that it is more likely that separated flow of iron and slag occurs in the taphole when the liquid outflow rates are comparable during tapping. The drainage process was simulated with an integrated model based on an overall balance analysis: The high in-furnace overpressure can compensate for the resistances induced by the liquid flows in the hearth and through the taphole. Finally, a recently developed multiphase CFD model including interfacial forces between immiscible liquids was developed and both the actual iron-slag system and a water-oil system in laboratory scale were simulated. The model was demonstrated to be a useful tool for simulating hearth flows for gaining understanding of the complex phenomena in the drainage of the blast furnace.

Lithostratigraphy and age of pre-Late Weichselian sediments in the Suupohja area, western Finland

Different types of laterally extensive sand- and gravel-dominated deposits, up to several tens of metres thick, were investigated in the Suupohja area of western Finland. The studied sediments were deposited in glacial, ice-marginal, glaciofluvial, sea or lake, littoral and terrestrial environments during several glacial-non-glacial cycles. Seventeen pre-Late Weichselian and three Late Weichselian/Holocene sedimentary units were identified. These were divided into ten formally and two informally defined formations that were together termed the Suupohja Group. Every unit are nevertheless not detectable throughout the study area. The informally defined “Karhukangas lower deposits” represent the lowest units in the Suupohja Group. The Karhukangas lower deposits with 5 till units, 3 glaciolacustrine/-marine units and 2 sand units, were interpreted as having been deposited during possibly four glacial-non-glacial cycles before the Late Pleistocene Subepoch (MIS 6 or earlier). The Kankalo Sand above the Karhukangas lower deposits comprises glaciofluvial and aeolian sands of Late Saalian, Eemian or Early Weichselian origin (MIS 6–MIS 5c). The Kariluoma Till above the Kankalo Sand was possibly deposited during the Late Saalian glacial advance, although an Early Weichselian origin is also possible. The Harrinkangas Formation, with glaciofluvial and quiet-water sediments, is interpreted as having been deposited during the Late Saalian and Eemian Stages (MIS 6–MIS 5e). The uppermost units in the deposits studied, the Kodesjärvi Formation (shore deposit), Isojoki Sand (aeolian), Rävåsen Formation (glaciofluvial), Vanhakylä Formation (shore line deposit), Dagsmark Till and Kauhajoki Till, were deposited during the Weichselian Stage (MIS 5d–MIS 2). In addition, Early Holocene (MIS 1) eskers without till cover were informally termed the “Holocene esker deposits”. The Lumikangas Formation represents gravelly shore deposits formed in the Holocene Epoch, when these areas last emerged from the sea. The first Weichselian ice expansion possibly reached the western part of Suupohja in the Early Weichselian Substage (MIS 5d?), but it did not expand further to the east. The second Weichselian glaciation of relatively short duration occupied the southern part of Finland in the later part of Middle Weichselian (MIS 3). Thus, the southern half of the country remained ice-free for the majority (~65–75%) of the Weichselian Stage. Instead, both humid temperate and periglacial conditions alternated. In the initial part of Middle Weichselian, this area was partly submerged, which indicates eastward expansion of the Scandinavian ice sheet(s), depressing the lithosphere. The exceptionally thick sediment cover, multiple lithofacies, relict landscape and preserved preglacially weathered bedrock are evidence of weak glacial erosion in the Suupohja area during the latest as well as earlier glaciations, making this area one of the key areas in Quaternary research.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Effects of early compost application on no-till organic soybean

Weed control has always been an important issue in agriculture. With the advent of no-till systems, soil erosion was reduced but herbicide use was increased. Organic no-till systems try to adjust reduced erosion to the no use of herbicides. Nevertheless, this adjustment is limited by the cost of mechanical weed control. This cost may be reduced by improved cultural weed control with cover crops mulches. In this paper we report a study on the application of compost manure on an oats winter cover crop, preceding soybean, instead of on the soybean summer crop. Treatments comprised a control without compost manure, and compost manure doses of 4 and 8 Mg ha-1 applied either on oats in winter or soybean in summer, organized in a randomized block design, with five replications. In summer, plots were split into weed-controlled or not controlled subplots. The timing of application and the manure doses did not affect the oats biomass or the soybean performance. However, in summer, without water stress, the application of manure at 8 Mg ha-1 directly on soybean has reduced weed biomass in this crop.

Growth inhibitors in turfgrass

Well-maintained lawns are comfortable and safe places for leisure activities and sports practice, and they also bring environmental benefits; for example, they reduce soil exposure to erosion and releases atmospheric CO2, thus reducing the greenhouse effect. However, regardless of the purpose of use or the choice of the plant species to form the lawn, the highest costs involve cutting that is needed to keep the turfgrass at its appropriate height. Successive lawn cutting operations are necessary basically because of the vegetative and reproductive growth of turfgrass which, in Brazil, occurs mainly from October to March. Expenditures with successive mechanical cuttings have fostered the search of alternative procedures to keep lawn plants at appropriate height, such as the use of plant growth inhibitors, an increasingly interesting procedure. Since the use of this technology in Brazil is still at its early stage, the aim of this literature review is to examine aspects associated with lawn management by using growth inhibitors. Another alternative is to increase the knowledge of the classification and rational application of the different compounds currently available in the market.