Growth, osmoregulation and ion accumulation in the coastal halophyte Arthrocnemum indicum under field conditions

Life cycle and population biology of a perennial halophyte Arthrocnemum indicum Willd, was studied from February 1992 to January 1993. During the 12 months, the population was exposed to great variations in soil salinity from 35 to 58 ms/cm2 and soil moisture ranging from flood to drought levels. Seasonal changes in dry weight are directly related to soil salinity stress. When salinity levels become low, the dry matter production increases. A little increase in dry weight from April to July indicates that more negative soil water potentials were limiting plant growth. Proline content increased considerably during the dry season with a corresponding increase in salinity. Water soluble oxalate did not vary much with changes in salinity.

ANNEALING BEHAVIOUR OF HIGH DOSE As** plus IMPLANTS.

The annealing behaviour of doses up to 4. 10**1**6 ions/cm**2 implanted at ion currents up to 10ma is described. Differences between rapid isothermal and furnace annealing in the measured sheet resistances are due to different amounts of diffusion and to loss of dopant by evaporation. Implantation at high currents (10ma) does not appear to affect the quality of the regrown material provided the temperature rise during implantation is small.

RESIDUAL DEFECTS FOLLOWING RAPID ANNEALING OF BORON IMPLANTED SILICON WITH AND WITHOUT PREAMORPHISATION BY SILICON IMPLANTATION.

Implants of boron into silicon which has been made amorphous by silicon implantation have a shallower depth profile than the same implants into silicon. This results in higher activation and restricted diffusion of the B implants after annealing, and there are also significant differences in the microstructure after annealing compared with B implants into silicon. Rapid isothermal heating with an electron beam and furnace treatments are used to characterize the defect structure as a function of time and temperature. Defects are seen to influence the diffusion of non-substitutional boron.

Mode control in vertical-cavity surface-emitting lasers by post-processing using focused ion-beaih etching

Single-mode emission is achieved in previously multimode gain-guided vertical-cavity surface-emitting lasers (VCSEL's) by localized modification of the mirror reflectivity using focused ion-beam etching. Reflectivity engineering is also demonstrated to suppress transverse mode emission in an oxide-confined device, reducing the spectral width from 1.2 nm to less than 0.5 nm.

Mechanism of polarization pinning in vertical cavity surface emitting lasers using focused ion beam etching

Photoluminescence experiments have identified strain as the origin for polarization pinning in vertical cavity surface emitting lasers post-processed by focused ion beam etching. Theoretical models were applied to deduce the strain in devices. Post-annealing was used to optimize polarization pinning.

High power laser with integrated lens using focused ion beam etching

In this study, a collimating lens is introduced at the output facet of a tapered waveguide laser to compensate for the divergence of the optical mode. The collimating lens is shown to enhance the laser efficiency while simultaneously reducing the far field divergence.

Focused ion beam etching of GaN

We have investigated the use of focused ion beam (FIB) etching for the fabrication of GaN-based devices. Although work has shown that conventional reactive ion etching (RIE) is in most cases appropriate for the GaN device fabrication, the direct write facility of FIB etching - a well-established technique for optical mask repair and for IC failure analysis and repair - without the requirement for depositing an etch mask is invaluable. A gallium ion beam of about 20nm diameter was used to sputter GaN material. The etching rate depends linearly on the ion dose per area with a slope of 3.5×10 -4μm3/pC. At a current of 3nA, for example, this corresponds to an etch rate of 1.05μm3/s. Good etching qualities have been achieved with a side wall roughness significantly below 0.1μm. Changes in the roughness of the etched surface plane stay below 8nm.

Humoral and protective response of Indian major carps to immersion vaccination with Aeromonas hydrophila

Fry of the Indian major carps, Catta catla (Ham.), Labeo rohita (Ham.) and Cirrhinus mrigala (Ham.) were immunized at 4 and 8 weeks post hatching (wph) by direct immersion in a suspension (10 super(8) cells ml super(-1))of heat inactivated Aeromonas hydrophila. Following the same procedure, booster dose was administered 20 days after the first immersion. Antibodies as well as protective response produced in both the groups after the first and the booster immersion were different and significant (P<0.05). No significant difference was found between the species in the two age groups. The specimens immunized 8 wph showed higher antibody titres and protection than the 4 wph group. C. catla had higher relative percent survival followed by L. rohita and C. mrigala.

Investigations on wooden floating materials: the loss of buoyancy under continuous immersion in water and the rate of its redemption by drying

A wooden fishing float under immersion in water for long periods is liable to absorb water, the quantity of water absorbed possibly being dependent upon the physical factors like the specific gravity and the inherent property of the material, the time of soaking and the pressure acting on it. Consequently a wooden float is likely to become heavy and loss its original buoyancy. However, when the float is removed from water and dried, the lost buoyancy is regained on complete drying. The present paper is an attempt to elucidate these two important characteristics of some of the chief wooden floating materials used on the West Coast of India.

Interspecies implantation and mitochondria fate of panda-rabbit cloned embryos

Somatic cell nuclei of giant pandas can dedifferentiate in enucleated rabbit ooplasm, and the reconstructed eggs can develop to blastocysts. In order to observe whether these interspecies cloned embryos can implant in the uterus of an animal other than th

Novel designs for Penning ion traps

A number of alternative designs are presented for Penning ion traps suitable for quantum information processing (QIP) applications with atomic ions. The first trap design is a simple array of long straight wires, which allows easy optical access. A prototype of this trap has been built to trap Ca+ and a simple electronic detection scheme has been employed to demonstrate the operation of the trap. Another trap design consists of a conducting plate with a hole in it situated above a continuous conducting plane. The final trap design is based on an array of pad electrodes. Although this trap design lacks the open geometry of the other traps described above, the pad design may prove useful in a hybrid scheme in which information processing and qubit storage take place in different types of trap. The behaviour of the pad traps is simulated numerically and techniques for moving ions rapidly between traps are discussed. Future experiments with these various designs are discussed. All of the designs lend themselves to the construction of multiple trap arrays, as required for scalable ion trap QIP.