A method for estimating intrinsic noise in electroretinographic (ERG) signals

Purpose To develop a signal processing paradigm for extracting ERG responses to temporal sinusoidal modulation with contrasts ranging from below perceptual threshold to suprathreshold contrasts. To estimate the magnitude of intrinsic noise in ERG signals at different stimulus contrasts. Methods Photopic test stimuli were generated using a 4-primary Maxwellian view optical system. The 4-primary lights were sinusoidally temporally modulated in-phase (36 Hz; 2.5 - 50% Michelson). The stimuli were presented in 1 s epochs separated by a 1 ms blank interval and repeated 160 times (160.16 s duration) during the recording of the continuous flicker ERG from the right eye using DTL fiber electrodes. After artefact rejection, the ERG signal was extracted using Fourier methods in each of the 1 s epochs where a stimulus was presented. The signal processing allows for computation of the intrinsic noise distribution in addition to the signal to noise (SNR) ratio. Results We provide the initial report that the ERG intrinsic noise distribution is independent of stimulus contrast whereas SNR decreases linearly with decreasing contrast until the noise limit at ~2.5%. The 1ms blank intervals between epochs de-correlated the ERG signal at the line frequency (50 Hz) and thus increased the SNR of the averaged response. We confirm that response amplitude increases linearly with stimulus contrast. The phase response shows a shallow positive relationship with stimulus contrast. Conclusions This new technique will enable recording of intrinsic noise in ERG signals above and below perceptual visual threshold and is suitable for measurement of continuous rod and cone ERGs across a range of temporal frequencies, and post-receptoral processing in the primary retinogeniculate pathways at low stimulus contrasts. The intrinsic noise distribution may have application as a biomarker for detecting changes in disease progression or treatment efficacy.

A suitable method for journal bearing wear measurement

Purpose – Ideally, there is no wear in hydrodynamic lubrication regime. A small amount of wear occurs during start and stop of the machines and the amount of wear is so small that it is difficult to measure with accuracy. Various wear measuring techniques have been used where out-of-roundness was found to be the most reliable method of measuring small wear quantities in journal bearings. This technique was further developed to achieve higher accuracy in measuring small wear quantities. The method proved to be reliable as well as inexpensive. The paper aims to discuss these issues. Design/methodology/approach – In an experimental study, the effect of antiwear additives was studied on journal bearings lubricated with oil containing solid contaminants. The test duration was too long and the wear quantities achieved were too small. To minimise the test duration, short tests of about 90 min duration were conducted and wear was measured recording changes in variety of parameters related to weight, geometry and wear debris. The out-of-roundness was found to be the most effective method. This method was further refined by enlarging the out-of-roundness traces on a photocopier. The method was proved to be reliable and inexpensive. Findings – Study revealed that the most commonly used wear measurement techniques such as weight loss, roughness changes and change in particle count were not adequate for measuring small wear quantities in journal bearings. Out-of-roundness method with some refinements was found to be one of the most reliable methods for measuring small wear quantities in journal bearings working in hydrodynamic lubrication regime. By enlarging the out-of-roundness traces and determining the worn area of the bearing cross-section, weight loss in bearings was calculated, which was repeatable and reliable. Research limitations/implications – This research is a basic in nature where a rudimentary solution has been developed for measuring small wear quantities in rotary devices such as journal bearings. The method requires enlarging traces on a photocopier and determining the shape of the worn area on an out-of-roundness trace on a transparency, which is a simple but a crude method. This may require an automated procedure to determine the weight loss from the out-of-roundness traces directly. This method can be very useful in reducing test duration and measuring wear quantities with higher precision in situations where wear quantities are very small. Practical implications – This research provides a reliable method of measuring wear of circular geometry. The Talyrond equipment used for measuring the change in out-of-roundness due to wear of bearings indicates that this equipment has high potential to be used as a wear measuring device also. Measurement of weight loss from the traces is an enhanced capability of this equipment and this research may lead to the development of a modified version of Talyrond type of equipment for wear measurements in circular machine components. Originality/value – Wear measurement in hydrodynamic bearings requires long duration tests to achieve adequate wear quantities. Out-of-roundness is one of the geometrical parameters that changes with progression of wear in a circular shape components. Thus, out-of-roundness is found to be an effective wear measuring parameter that relates to change in geometry. Method of increasing the sensitivity and enlargement of out-of-roundness traces is original work through which area of worn cross-section can be determined and weight loss can be derived for materials of known density with higher precision.

The dependence of computed tomography number to relative electron density conversion on phantom geometry and its impact on planned dose

A computed tomography number to relative electron density (CT-RED) calibration is performed when commissioning a radiotherapy CT scanner by imaging a calibration phantom with inserts of specified RED and recording the CT number displayed. In this work, CT-RED calibrations were generated using several commercially available phantoms to observe the effect of phantom geometry on conversion to electron density and, ultimately, the dose calculation in a treatment planning system. Using an anthropomorphic phantom as a gold standard, the CT number of a material was found to depend strongly on the amount and type of scattering material surrounding the volume of interest, with the largest variation observed for the highest density material tested, cortical bone. Cortical bone gave a maximum CT number difference of 1,110 when a cylindrical insert of diameter 28 mm scanned free in air was compared to that in the form of a 30 × 30 cm2 slab. The effect of using each CT-RED calibration on planned dose to a patient was quantified using a commercially available treatment planning system. When all calibrations were compared to the anthropomorphic calibration, the largest percentage dose difference was 4.2 % which occurred when the CT-RED calibration curve was acquired with heterogeneity inserts removed from the phantom and scanned free in air. The maximum dose difference observed between two dedicated CT-RED phantoms was ±2.1 %. A phantom that is to be used for CT-RED calibrations must have sufficient water equivalent scattering material surrounding the heterogeneous objects that are to be used for calibration.

Altered nociceptive, endocrine, and dorsal horn neuron responses in rats following a neonatal immune challenge

Summary The neonatal period is characterized by significant plasticity where the immune, endocrine, and nociceptive systems undergo fine-tuning and maturation. Painful experiences during this period can result in long-term alterations in the neurocircuitry underlying nociception, including increased sensitivity to mechanical or thermal stimuli. Less is known about the impact of neonatal exposure to mild inflammatory stimuli, such as lipopolysaccharide (LPS), on subsequent inflammatory pain responses. Here we examine the impact of neonatal LPS exposure on inflammatory pain sensitivity and HPA axis activity during the first three postnatal weeks. Wistar rats were injected with LPS (0.05 mg/kg IP, Salmonella enteritidis) or saline on postnatal days (PNDs) 3 and 5 and later subjected to the formalin test at PNDs 7, 13, and 22. One hour after formalin injection, blood was collected to assess corticosterone responses. Transverse spinal cord slices were also prepared for whole-cell patch clamp recording from lumbar superficial dorsal horn neurons (SDH). Brains were obtained at PND 22 and the hypothalamus was isolated to measure glucocorticoid (GR) and mineralocorticoid receptor (MR) transcript expression using qRT-PCR. Behavioural analyses indicate that at PND 7, no significant differences were observed between saline- or LPS-challenged rats. At PND 13, LPS-challenged rats exhibited enhanced licking (p < .01), and at PND 22, increased flinching in response to formalin injection (p < .05). LPS-challenged rats also displayed increased plasma corticosterone at PND 7 and PND 22 (p < .001) but not at PND 13 following formalin administration. Furthermore, at PND 22 neonatal LPS exposure induced decreased levels of GR mRNA and increased levels of MR mRNA in the hypothalamus. The intrinsic properties of SDH neurons were similar at PND 7 and PND 13. However, at PND 22, ipsilateral SDH neurons in LPS-challenged rats had a lower input resistance compared to their saline-challenged counterparts (p < .05). These data suggest neonatal LPS exposure produces developmentally regulated changes in formalin-induced behavioural responses, corticosterone levels, and dorsal horn neuron properties following noxious stimulation later in life. These findings highlight the importance of immune activation during the neonatal period in shaping pain sensitivity later in life. This programming involves both spinal cord neurons and the HPA axis.

The iconic and the critical

Theodor Adorno was opposed to the cinema because he felt it was too close to reality, and ipso facto an extension of ideological Capital, as he wrote in 1944 in Dialectic of Enlightenment. What troubled Adorno was the iconic nature of cinema – the semiotic category invented by C. S. Peirce where the signifier (sign) does not merely signify, in the arbitrary capacity attested by Saussure, but mimics the formal-visual qualities of its referent. Iconicity finds its perfect example in the film’s ingenuous surface illusion of an unmediated reality – its genealogy (the iconic), since classical antiquity, lay in the Greek term eikōn which meant “image,” to refer to the ancient portrait statues of victorious athletes which were thought to bear a direct similitude with their parent divinities. For the postwar, Hollywood-film spectator, Adorno said, “the world outside is an extension of the film he has just left,” because realism is a precise instrument for the manipulation of the mass spectator by the culture industry, for which the filmic image is an advertisement for the world unedited. Mimesis, or the reproduction of reality, is a “mere reproduction of the economic base.” It is precisely film’s iconicity, then, its “realist aesthetic . . . [that] makes it inseparable from its commodity character.”...

Evaluation framework to assess orthopaedic procedures

Introduction & aims The demand for evidence of efficacy of treatments in general and orthopaedic surgical procedures in particular is ever increasing in Australia and worldwide. The aim of this study is to share the key elements of an evaluation framework recently implemented in Australia to determine the efficacy of bone-anchored prostheses. Method The proposed evaluation framework to determine the benefit and harms of bone-anchored prostheses for individuals with limb loss was extracted from a systematic review of the literature including seminal studies focusing on clinical benefits and safety of procedures involving screw-type implant (e.g., OPRA) and press-fit fixations (e.g., EEFT, ILP, OPL). [1-64] Results The literature review highlighted that a standard and replicable evaluation framework should focus on: • The clinical benefits with a systematic recording of health-related quality of life (e.g., SF-26, Q-TFA), mobility predictor (e.g., AMPRO), ambulation abilities (e.g., TUG, 6MWT), walking abilities (e.g., characteristic spatio-temporal) and actual activity level at baseline and follow-up post Stage 2 surgery, • The potential harms with systematic recording of residuum care, infection, implant stability, implant integrity, injuries (e.g., falls) after Stage 1 surgery. There was a general consensus around the instruments to monitor most of the benefits and harms. The benefits could be assessed using a wide spectrum of complementary assessments ranging from subjective patient self-reporting to objective measurements of physical activity. However, this latter was assessed using a broad range of measurements (e.g., pedometer, load cell, energy consumption). More importantly, the lack of consistent grading of infections was sufficiently noticeable to impede cross-fixation comparisons. Clearly, a more universal grading system is needed. Conclusions Investigators are encouraged to implement an evaluation framework featuring the domains and instruments proposed above using a single database to facilitate robust prospective studies about potential benefits and harms of their procedure. This work is also a milestone in the development of national and international clinical outcome registries.

Partial epilepsy syndrome in a Gypsy family linked to 5q31.3-q32

PURPOSE The restricted genetic diversity and homogeneous molecular basis of Mendelian disorders in isolated founder populations have rarely been explored in epilepsy research. Our long-term goal is to explore the genetic basis of epilepsies in one such population, the Gypsies. The aim of this report is the clinical and genetic characterization of a Gypsy family with a partial epilepsy syndrome. METHODS Clinical information was collected using semistructured interviews with affected subjects and informants. At least one interictal electroencephalography (EEG) recording was performed for each patient and previous data obtained from records. Neuroimaging included structural magnetic resonance imaging (MRI). Linkage and haplotype analysis was performed using the Illumina IVb Linkage Panel, supplemented with highly informative microsatellites in linked regions and Affymetrix SNP 5.0 array data. RESULTS We observed an early-onset partial epilepsy syndrome with seizure semiology strongly suggestive of temporal lobe epilepsy (TLE), with mild intellectual deficit co-occurring in a large proportion of the patients. Psychiatric morbidity was common in the extended pedigree but did not cosegregate with epilepsy. Linkage analysis definitively excluded previously reported loci, and identified a novel locus on 5q31.3-q32 with an logarithm of the odds (LOD) score of 3 corresponding to the expected maximum in this family. DISCUSSION The syndrome can be classified as familial temporal lobe epilepsy (FTLE) or possibly a new syndrome with mild intellectual deficit. The linked 5q region does not contain any ion channel-encoding genes and is thus likely to contribute new knowledge about epilepsy pathogenesis. Identification of the mutation in this family and in additional patients will define the full phenotypic spectrum.

Physical activity cost in children following an acquired brain injury : a comparative study

Background: Alterations in energy expenditure during activity post head injury has not been investigated due primarily to the difficulty of measurement. Objective: The aim of this study was to compare energy expenditure during activity and body composition of children following acquired brain injury (ABI) with data from a group of normal controls. Design: Energy expenditure was measured using the Cosmed K4b2 in a group of 15 children with ABI and a group of 67 normal children during rest and when walking and running. Mean number of steps taken per 3 min run was also recorded and body composition was measured. Results: The energy expended during walking was not significantly different between both groups. A significant difference was found between the two groups in the energy expended during running and also for the number of steps taken as children with ABI took significantly less steps than the normal controls during a 3 min run. Conclusions: Children with ABI exert more energy per activity than healthy controls when controlled for velocity or distance. However, they expend less energy to walk and run when they are free to choose their own desirable, comfortable pace than normal controls. © 2003 Elsevier Ltd. All rights reserved.

Improving factory performance using an integrated sugar factory model

A whole of factory model of a raw sugar factory was developed in SysCAD software to assess and improve factory operations. The integrated sugar factory model ‘Sugar-SysCAD’ includes individual models for milling, heating and clarification, evaporation, crystallisation, steam cycle, sugar dryer and process and injection water circuits. These individual unit operation models can be either used as standalone models to optimise the unit operation or in the integrated mode to provide more accurate prediction of the effects of changes in any part of the process on the outputs of the whole factory process. Using the integrated sugar factory model, the effect of specific process operations can be understood and practical solutions can be determined to address process problems. The paper presents two factory scenarios to show the capabilities of the whole of factory model.

The effects of gas and air flow distributions on the performance of the Farleigh No. 3 boiler

As more raw sugar factories become involved in the manufacture of by-products and cogeneration, bagasse is becoming an increasingly valuable commodity. However, in most factories, most of the bagasse produced is used to generate steam in relatively old and inefficient boilers. Efficient bagasse fired boilers are a high capital cost item and the cost of supplying the steam required to run a sugar factory by other means is prohibitive. For many factories a more realistic way to reduce bagasse consumption is to increase the efficiency of existing boilers. The Farleigh No. 3 boiler is a relatively old low efficiency boiler. Like many in the industry, the performance of this boiler has been adversely affected by uneven gas and air flow distributions and air heater leaks. The combustion performance and efficiency of this boiler have been significantly improved by making the gas and air flow distributions through the boiler more uniform and repairing the air heater. The estimated bagasse savings easily justify the cost of the boiler improvements.

Computer-assisted sampling of acoustic data for more efficient determination of bird species richness

Bird species richness survey is one of the most intriguing ecological topics for evaluating environmental health. Here, bird species richness denotes the number of unique bird species in a particular area. Factors affecting the investigation of bird species richness include weather, observation bias, and most importantly, the prohibitive costs of conducting surveys at large spatiotemporal scales. Thanks to advances in recording techniques, these problems have been alleviated by deploying sensors for acoustic data collection. Although automated detection techniques have been introduced to identify various bird species, the innate complexity of bird vocalizations, the background noise present in the recording and the escalating volumes of acoustic data pose a challenging task on determination of bird species richness. In this paper we proposed a two-step computer-assisted sampling approach for determining bird species richness in one-day acoustic data. First, a classification model is built based on acoustic indices for filtering out minutes that contain few bird species. Then the classified bird minutes are ordered by an acoustic index and the redundant temporal minutes are removed from the ranked minute sequence. The experimental results show that our method is more efficient in directing experts for determination of bird species compared with the previous methods.

The Australian naturalistic driving study: From beginnings to launch

The Australian Naturalistic Driving Study (ANDS), a ground-breaking study of Australian driver behaviour and performance, was officially launched on April 21st, 2015 at UNSW. The ANDS project will provide a realistic perspective on the causes of vehicle crashes and near miss crash events, along with the roles speeding, distraction and other factors have on such events. A total of 360 volunteer drivers across NSW and Victoria - 180 in NSW and 180 in Victoria - will be monitored by a Data Acquisition System (DAS) recording continuously for 4 months their driving behaviour using a suite of cameras and sensors. Participants’ driving behaviour (e.g. gaze), the behaviour of their vehicle (e.g. speed, lane position) and the behaviour of other road users with whom they interact in normal and safety-critical situations will be recorded. Planning of the ANDS commenced over two years ago in June 2013 when the Multi-Institutional Agreement for a grant supporting the equipment purchase and assembly phase was signed by parties involved in this large scale $4 million study (5 university accident research centres, 3 government regulators, 2 third party insurers and 2 industry partners). The program’s second development phase commenced a year later in June 2014 after a second grant was awarded. This paper presents an insider's view into that two year process leading up to the launch, and outlines issues that arose in the set-up phase of the study and how these were addressed. This information will be useful to other organisations considering setting up an NDS.

Echoes: World music from Queensland

Research background: Echoes-World Music in Queensland is a full-length album produced in collaboration with the Brisbane Multicultural Arts Centre (BEMAC). The project involved the recording and production of 13 different artists’ original compositions and arrangements of traditional works, drawing on hybrid digital-analog production techniques. The recording of the album was informed by prior scholarly work by Taylor, Feld, Wong and others. These existing studies have discussed the complexities of intercultural collaboration, and the types of cultural politics that are involved in the recording and distribution of what has been known by the term ‘World Music.’ Aspects of applied ethnomusicology have informed the creative work, as a means of interpreting the implicit and explicit complexities that arise through the recording and dissemination of intercultural creative practice. The project asked the research question, in what ways is intercultural music making effected by collaborative practices in the recording studio? Research contribution: This project has identified that the recording and production of intercultural music making involves a complex amalgam of aspects of live or ‘authentic’ performance practices, alongside highly mediated production practices that are influenced by new forms of digital recording technology. Research significance: The compact disc was launched at a live performance showcase as part of the 2014 Big Sound music industry conference, and was added to feature album rotation for all Virgin Australia flights in February-March 2015. The album has received airplay on Radio National, Edge Radio (Hobart) and Radio Adelaide, and was a Feature Album on PBS FM (Melbourne), 2SER (Sydney), and ArtsoundFM Canberrra. The research context of the work is detailed in Gavin Carfoot (in press), ‘Musical discovery, colonialism and the possibilities of intercultural communication through music’ in Popular Communication.

Josh lovegrove: Infinite

Research background: Infinite by Josh Lovegrove is an extended play album co-produced in collaboration with ARIA-nominated artist Mark Sholtez. The album consists of original songs written by Lovegrove, and songs co-written by Lovegrove, Carfoot and Sholtez. The scholarly context of the project is informed by studies of songwriting and ambiguity by Negus and Astor, new approaches to the study of record production associated with Zagorski-Thomas, and studies of creative labour by Hesmondhalgh and Baker. The project focused on the dynamics of musical performance and production in the recording studio, investigating the interface between the creative tasks of songwriting, production and performance in the recording of popular music. The project asked, in what ways do collaborative songwriting and production processes overlap, how has the nature of creative labour changed as a result of new forms of digital recording technology, and how can these aspects inform developments in the learning and teaching of popular music? Research contribution: The project has demonstrated the nuanced ways that the practices of record production have changed in the face of technological developments, and how this has impacted upon the specific forms and divisions of creative labour. Research significance: The project resulted in a well-reviewed album release that has further established Lovegrove’s reputation as a performer and songwriter. The creative work underpins ongoing research into the nature of popular music production, in particular how the nature of collaborative songwriting can inform innovation in the learning and teaching of popular music.

Mrs Curly and the Norwegian Smoking Pipe

Research background: Mrs Curly and the Norwegian Smoking Pipe is a full-length album and book release, produced in collaboration with renowned multi-instrumentalist Linsey Pollak. The project involved the recording and production of Pollak’s original compositions and arrangements of traditional works, drawing on hybrid digital-analog production techniques. The recording of the album was informed by prior scholarly work by Taylor, Feld, Wong and others. These existing studies have discussed the complexities of intercultural collaboration, and the types of cultural politics that are involved in the recording and distribution of what has been known by the term ‘World Music.’ Aspects of applied ethnomusicology have informed the creative work, as a means of interpreting the implicit and explicit complexities that arise through the recording and dissemination of intercultural creative practice. The project asked the research question, in what ways is intercultural music making effected by collaborative practices in the recording studio? Research contribution: This project has identified that the recording and production of intercultural music making involves a complex amalgam of aspects of live or ‘authentic’ performance practices, alongside highly mediated production practices that are influenced by new forms of digital recording technology. Research significance: The compact disc and book was released and promoted on the Marata Music label. The song ‘Plačam za’ was nominated in the World category of the 2015 Queensland Music Awards. The research context of the work is detailed in Gavin Carfoot, 2015 (in press), ‘Musical discovery, colonialism and the possibilities of intercultural communication through music’ in Popular Communication.