Beam steering with high front-to-back ratio and high directivity on small platforms using decoupled antenna pairs

Beam steering with high front-to-back ratio and high directivity on a small platform is proposed. Two closely spaced antenna pairs with eigenmode port decoupling are used as the basic radiating elements. Two orthogonal radiation patterns are obtained for each antenna pair. High front-to-back ratio and high directivity are achieved by combining the two orthogonal radiation patterns. With an infinite groundplane, a front-to-back ratio of 21 dB with a directivity of 9.8 dB can be achieved. Beam steering, at the expense of a slight decrease in directivity, is achieved by placing the two antenna pairs 0.5λ apart. The simulated half power beamwidth is 58°. A prototype was designed and the 2-D radiation patterns were measured. The prototype supports three directions of beam steering. The half power beamwidth was measured as 46°, 48°, and 50° for the three respective beam directions. The measured front-to-back ratio in azimuth plane is 8.5 dB, 8.0 dB and 7.6 dB, respectively.

Mapping the language of science and science teaching practices : a case study of early childhood school science

Concerns raised in educational reports about school science in terms of students. outcomes and attitudes, as well as science teaching practices prompted investigation into science learning and teaching practices at the foundational level of school science. Without science content and process knowledge, understanding issues of modern society and active participation in decision-making is difficult. This study contended that a focus on the development of the language of science could enable learners to engage more effectively in learning science and enhance their interest and attitudes towards science. Furthermore, it argued that explicit teaching practices where science language is modelled and scaffolded would facilitate the learning of science by young children at the beginning of their formal schooling. This study aimed to investigate science language development at the foundational level of school science learning in the preparatory-school with students aged five and six years. It focussed on the language of science and science teaching practices in early childhood. In particular, the study focussed on the capacity for young students to engage with and understand science language. Previous research suggests that students have difficulty with the language of science most likely because of the complexities and ambiguities of science language. Furthermore, literature indicates that tensions transpire between traditional science teaching practices and accepted early childhood teaching practices. This contention prompted investigation into means and models of pedagogy for learning foundational science language, knowledge and processes in early childhood. This study was positioned within qualitative assumptions of research and reported via descriptive case study. It was located in a preparatory-school classroom with the class teacher, teacher-aide, and nineteen students aged four and five years who participated with the researcher in the study. Basil Bernstein.s pedagogical theory coupled with Halliday.s Systemic Functional Linguistics (SFL) framed an examination of science pedagogical practices for early childhood science learning. Students. science learning outcomes were gauged by focussing a Hallydayan lens on their oral and reflective language during 12 science-focussed episodes of teaching. Data were collected throughout the 12 episodes. Data included video and audio-taped science activities, student artefacts, journal and anecdotal records, semi-structured interviews and photographs. Data were analysed according to Bernstein.s visible and invisible pedagogies and performance and competence models. Additionally, Halliday.s SFL provided the resource to examine teacher and student language to determine teacher/student interpersonal relationships as well as specialised science and everyday language used in teacher and student science talk. Their analysis established the socio-linguistic characteristics that promoted science competencies in young children. An analysis of the data identified those teaching practices that facilitate young children.s acquisition of science meanings. Positive indications for modelling science language and science text types to young children have emerged. Teaching within the studied setting diverged from perceived notions of common early childhood practices and the benefits of dynamic shifting pedagogies were validated. Significantly, young students demonstrated use of particular specialised components of school-science language in terms of science language features and vocabulary. As well, their use of language demonstrated the students. knowledge of science concepts, processes and text types. The young students made sense of science phenomena through their incorporation of a variety of science language and text-types in explanations during both teacher-directed and independent situations. The study informs early childhood science practices as well as practices for foundational school science teaching and learning. It has exposed implications for science education policy, curriculum and practices. It supports other findings in relation to the capabilities of young students. The study contributes to Systemic Functional Linguistic theory through the development of a specific resource to determine the technicality of teacher language used in teaching young students. Furthermore, the study contributes to methodology practices relating to Bernsteinian theoretical perspectives and has demonstrated new ways of depicting and reporting teaching practices. It provides an analytical tool which couples Bernsteinian and Hallidayan theoretical perspectives. Ultimately, it defines directions for further research in terms of foundation science language learning, ongoing learning of the language of science and learning science, science teaching and learning practices, specifically in foundational school science, and relationships between home and school science language experiences.

The effect of ocular surface conditions on blink rate and completeness

A healthy human would be expected to show periodic blinks, making a brief closure of the eyelids. Most blinks are spontaneous, occurring regularly with no external stimulus. However a reflex blink can occur in response to external stimuli such as a bright light, a sudden loud noise, or an object approaching toward the eyes. A voluntary or forced blink is another type of blink in which the person deliberately closes the eyes and the lower eyelid raises to meet the upper eyelid. A complete blink, in which the upper eyelid touches the lower eyelid, contributes to the health of ocular surface by providing a fresh layer of tears as well as maintaining optical integrity by providing a smooth tear film over the cornea. The rate of blinking and its completeness vary depending on the task undertaken during blink assessment, the direction of gaze, the emotional state of the subjects and the method under which the blink was measured. It is also well known that wearing contact lenses (both rigid and soft lenses) can induce significant changes in blink rate and completeness. It is been established that efficient blinking plays an important role in ocular surface health during contact lens wear and for improving contact lens performance and comfort. Inefficient blinking during contact lens wear may be related to a low blink rate or incomplete blinking and can often be a reason for dry eye symptoms or ocular surface staining. It has previously been shown that upward gaze can affect blink rate, causing it to become faster. In the first experiment, it was decided to expand on previous studies in this area by examining the effect of various gaze directions (i.e. upward gaze, primary gaze, downward gaze and lateral gaze) as well as head angle (recumbent position) on normal subjects’ blink rate and completeness through the use of filming with a high-speed camera. The results of this experiment showed that as the open palpebral aperture (and exposed ocular surface area) increased from downward gaze to upward gaze, the number of blinks significantly increased (p<0.04). Also, the size of closed palpebral aperture significantly increased from downward gaze to upward gaze (p<0.005). A weak positive correlation (R² = 0.18) between the blink rate and ocular surface area was found in this study. Also, it was found that the subjects showed 81% complete blinks, 19% incomplete blinks and 2% of twitch blinks in primary gaze, consistent with previous studies. The difference in the percentage of incomplete blinks between upward gaze and downward gaze was significant (p<0.004), showing more incomplete blinks in upward gaze. The findings of this experiment suggest that while blink rate becomes slower in downward gaze, the completeness of blinking is typically better, thereby potentially reducing the risk of tear instability. On the other hand, in upward gaze while the completeness of blinking becomes worse, this is potentially offset by increased blink frequency. In addition, blink rate and completeness were not affected by lateral gaze or head angle, possibly because these conditions have similar size of the open palpebral aperture compared with primary gaze. In the second experiment, an investigation into the changes in blink rate and completeness was carried out in primary gaze and downward gaze with soft and rigid contact lenses in unadapted wearers. Not surprisingly, rigid lens wear caused a significant increase in the blink rate in both primary (p<0.001) and downward gaze (p<0.02). After fitting rigid contact lenses, the closed palpebral aperture (blink completeness) did not show any changes but the open palpebral aperture showed a significant narrowing (p<0.04). This might occur from the subjects’ attempt to avoid interaction between the upper eyelid and the edge of the lens to minimize discomfort. After applying topical anaesthetic eye drops in the eye fitted with rigid lenses, the increased blink rate dropped to values similar to that before lens insertion and the open palpebral aperture returned to baseline values, suggesting that corneal and/or lid margin sensitivity was mediating the increased blink rate and narrowed palpebral aperture. We also investigated the changes in the blink rate and completeness with soft contact lenses including a soft sphere, double slab-off toric design and periballast toric design. Soft contact lenses did not cause any significant changes in the blink rate, closed palpebral aperture, open palpebral aperture and the percentage of incomplete blinks in either primary gaze or downward gaze. After applying anaesthetic eye drops, the blink rate reduced in both primary gaze and downward gaze, however this difference was not statistically significant. The size of the closed palpebral aperture and open palpebral aperture did not show any significant changes after applying anaesthetic eye drops. However it should be noted that the effects of rigid and soft contact lenses that we observed in these studies were only the immediate reaction to contact lenses and in the longer term, it is likely that these responses will vary as the eye adapts to the presence of the lenses.

Developing a knowledge base for enterprise system success: the role of management and operational staff

Knowledge base is one of the emerging concepts in the Knowledge Management area. As there exists no agreed- upon standard definition of a knowledge base, this paper defines a knowledge base in terms of our research of Enterprise Systems (ES). The knowledge base is defined with reference to Learning Network Theory. Using this theoretical framework, we investigate the roles of management and operational staff in organisations and how their interactions can create a better ES-knowledge base to contribute to ES success. We focus on the post- implementation phase of ES as part of the ES lifecycle. Our findings will facilitate future research directions and contribute to better understandings of how the knowledge base can be integrated and how this integration leads to Enterprise System success.

Information literacy programs and research : an international review

This paper provides an overview of contemporary information literacy research and practice. While the content is highly selective, the intention has been to highlight international and Australian developments which have achieved significant recognition, which are representative of similar trends in other places, or which are unique in some way. There are three main foci in the paper. Firstly, an exploration of ways of interpreting the idea of information literacy. Secondly, a synthesis of various efforts to seek new directions in educational, community and workplace contexts, beginning with the major initiatives being undertaken in the United States. Thirdly, an introduction to some recent research, concluding with a summary of my own investigation into different ways of experiencing information literacy

The geometric modelling of social frames and contexts

How do humans respond to their social context? This question is becoming increasingly urgent in a society where democracy requires that the citizens of a country help to decide upon its policy directions, and yet those citizens frequently have very little knowledge of the complex issues that these policies seek to address. Frequently, we find that humans make their decisions more with reference to their social setting, than to the arguments of scientists, academics, and policy makers. It is broadly anticipated that the agent based modelling (ABM) of human behaviour will make it possible to treat such social effects, but we take the position here that a more sophisticated treatment of context will be required in many such models. While notions such as historical context (where the past history of an agent might affect its later actions) and situational context (where the agent will choose a different action in a different situation) abound in ABM scenarios, we will discuss a case of a potentially changing context, where social effects can have a strong influence upon the perceptions of a group of subjects. In particular, we shall discuss a recently reported case where a biased worm in an election debate led to significant distortions in the reports given by participants as to who won the debate (Davis et al 2011). Thus, participants in a different social context drew different conclusions about the perceived winner of the same debate, with associated significant differences among the two groups as to who they would vote for in the coming election. We extend this example to the problem of modelling the likely electoral responses of agents in the context of the climate change debate, and discuss the notion of interference between related questions that might be asked of an agent in a social simulation that was intended to simulate their likely responses. A modelling technology which could account for such strong social contextual effects would benefit regulatory bodies which need to navigate between multiple interests and concerns, and we shall present one viable avenue for constructing such a technology. A geometric approach will be presented, where the internal state of an agent is represented in a vector space, and their social context is naturally modelled as a set of basis states that are chosen with reference to the problem space.

The student as customer model and its impact on the academic leadership role in higher education

This paper posits that the 'student as customer' model has a negative impact upon the academic leadership which in turn is responsible for the erosion of objectivity in the assessment process in the higher education sector. The paper draws on the existing literature to explore the relationship between the student as customer model, academic leadership, and student assessment. The existing research emanating from the literature provides the basis from which the short comings of the student as customer model are exposed. From a practical perspective the arguments made in this paper provide the groundwork for possible future research into the adverse affects of the student as customer model on academic leadership and job satisfaction in the academic work force. The concern for quality may benefit from empirical investigation of the relationship between the student as customer model and quality learning and assessment outcomes in the higher education sector. The paper raises awareness of the faults with the present reliance on the student as customer model and the negative impact on both students and academic staff. The issues explored have the potential to influence the future directions of the higher education sector with regard to the social implications of their quest for quality educational outcomes. The paper addresses a gap in the literature in regard to use of the student as customer model and the subsequent adverse affect on academic leadership and assessment in higher education.

Barriers to information transfer for multi-trauma patients upon discharge from the Emergency Department in a tertiary level hospital

Purpose: Communication is integral to effective trauma care provision. This presentation will report on barriers to meaningful information transfer for multi-trauma patients upon discharge from the Emergency Department (ED) to the care areas of Intensive Care Unit, High Dependency Unit, and Perioperative Services. This is an ongoing study at one tertiary level hospital in Queensland. Method: This is a multi-phase, mixed method study. In Phase 1 data were collected about information transfer. This Phase was initially informed by a comprehensive literature review, then via focus groups, chart audit, staff survey and review of national and international trauma forms. Results: The barriers identified related to nursing handover, documented information, time inefficiency, patient complexity and stability and time of transfer. Specifically this included differences in staff expectations and variation in the nursing handover processes, no agreed minimum dataset of information handed over, missing, illegible or difficult to find information in documentation (both medical and nursing), low compliance with some forms used for documentation. Handover of these patients is complex with information coming from many sources, dealing with issues is more difficult for these patients when transferred out of hours. Conclusions and further directions: This study investigated the current communication processes and standards of information transfer to identify barriers and issues. The barriers identified were the structure used for documentation, processes used (e.g. handover), patient acuity and time. This information is informing the development, implementation and evaluation of strategies to ameliorate the issues identified.

Analysis of productive performance of crop and animal production systems : an integrated analytical framework

This article presents a two-stage analytical framework that integrates ecological crop (animal) growth and economic frontier production models to analyse the productive efficiency of crop (animal) production systems. The ecological crop (animal) growth model estimates "potential" output levels given the genetic characteristics of crops (animals) and the physical conditions of locations where the crops (animals) are grown (reared). The economic frontier production model estimates "best practice" production levels, taking into account economic, institutional and social factors that cause farm and spatial heterogeneity. In the first stage, both ecological crop growth and economic frontier production models are estimated to calculate three measures of productive efficiency: (1) technical efficiency, as the ratio of actual to "best practice" output levels; (2) agronomic efficiency, as the ratio of actual to "potential" output levels; and (3) agro-economic efficiency, as the ratio of "best practice" to "potential" output levels. Also in the first stage, the economic frontier production model identifies factors that determine technical efficiency. In the second stage, agro-economic efficiency is analysed econometrically in relation to economic, institutional and social factors that cause farm and spatial heterogeneity. The proposed framework has several important advantages in comparison with existing proposals. Firstly, it allows the systematic incorporation of all physical, economic, institutional and social factors that cause farm and spatial heterogeneity in analysing the productive performance of crop and animal production systems. Secondly, the location-specific physical factors are not modelled symmetrically as other economic inputs of production. Thirdly, climate change and technological advancements in crop and animal sciences can be modelled in a "forward-looking" manner. Fourthly, knowledge in agronomy and data from experimental studies can be utilised for socio-economic policy analysis. The proposed framework can be easily applied in empirical studies due to the current availability of ecological crop (animal) growth models, farm or secondary data, and econometric software packages. The article highlights several directions of empirical studies that researchers may pursue in the future.

Quantification of particle emission characteristics and development of an emission model for use in transport microenvironments affected by traffic emissions

Vehicle emitted particles are of significant concern based on their potential to influence local air quality and human health. Transport microenvironments usually contain higher vehicle emission concentrations compared to other environments, and people spend a substantial amount of time in these microenvironments when commuting. Currently there is limited scientific knowledge on particle concentration, passenger exposure and the distribution of vehicle emissions in transport microenvironments, partially due to the fact that the instrumentation required to conduct such measurements is not available in many research centres. Information on passenger waiting time and location in such microenvironments has also not been investigated, which makes it difficult to evaluate a passenger’s spatial-temporal exposure to vehicle emissions. Furthermore, current emission models are incapable of rapidly predicting emission distribution, given the complexity of variations in emission rates that result from changes in driving conditions, as well as the time spent in driving condition within the transport microenvironment. In order to address these scientific gaps in knowledge, this work conducted, for the first time, a comprehensive statistical analysis of experimental data, along with multi-parameter assessment, exposure evaluation and comparison, and emission model development and application, in relation to traffic interrupted transport microenvironments. The work aimed to quantify and characterise particle emissions and human exposure in the transport microenvironments, with bus stations and a pedestrian crossing identified as suitable research locations representing a typical transport microenvironment. Firstly, two bus stations in Brisbane, Australia, with different designs, were selected to conduct measurements of particle number size distributions, particle number and PM2.5 concentrations during two different seasons. Simultaneous traffic and meteorological parameters were also monitored, aiming to quantify particle characteristics and investigate the impact of bus flow rate, station design and meteorological conditions on particle characteristics at stations. The results showed higher concentrations of PN20-30 at the station situated in an open area (open station), which is likely to be attributed to the lower average daily temperature compared to the station with a canyon structure (canyon station). During precipitation events, it was found that particle number concentration in the size range 25-250 nm decreased greatly, and that the average daily reduction in PM2.5 concentration on rainy days compared to fine days was 44.2 % and 22.6 % at the open and canyon station, respectively. The effect of ambient wind speeds on particle number concentrations was also examined, and no relationship was found between particle number concentration and wind speed for the entire measurement period. In addition, 33 pairs of average half-hourly PN7-3000 concentrations were calculated and identified at the two stations, during the same time of a day, and with the same ambient wind speeds and precipitation conditions. The results of a paired t-test showed that the average half-hourly PN7-3000 concentrations at the two stations were not significantly different at the 5% confidence level (t = 0.06, p = 0.96), which indicates that the different station designs were not a crucial factor for influencing PN7-3000 concentrations. A further assessment of passenger exposure to bus emissions on a platform was evaluated at another bus station in Brisbane, Australia. The sampling was conducted over seven weekdays to investigate spatial-temporal variations in size-fractionated particle number and PM2.5 concentrations, as well as human exposure on the platform. For the whole day, the average PN13-800 concentration was 1.3 x 104 and 1.0 x 104 particle/cm3 at the centre and end of the platform, respectively, of which PN50-100 accounted for the largest proportion to the total count. Furthermore, the contribution of exposure at the bus station to the overall daily exposure was assessed using two assumed scenarios of a school student and an office worker. It was found that, although the daily time fraction (the percentage of time spend at a location in a whole day) at the station was only 0.8 %, the daily exposure fractions (the percentage of exposures at a location accounting for the daily exposure) at the station were 2.7% and 2.8 % for exposure to PN13-800 and 2.7% and 3.5% for exposure to PM2.5 for the school student and the office worker, respectively. A new parameter, “exposure intensity” (the ratio of daily exposure fraction and the daily time fraction) was also defined and calculated at the station, with values of 3.3 and 3.4 for exposure to PN13-880, and 3.3 and 4.2 for exposure to PM2.5, for the school student and the office worker, respectively. In order to quantify the enhanced emissions at critical locations and define the emission distribution in further dispersion models for traffic interrupted transport microenvironments, a composite line source emission (CLSE) model was developed to specifically quantify exposure levels and describe the spatial variability of vehicle emissions in traffic interrupted microenvironments. This model took into account the complexity of vehicle movements in the queue, as well as different emission rates relevant to various driving conditions (cruise, decelerate, idle and accelerate), and it utilised multi-representative segments to capture the accurate emission distribution for real vehicle flow. This model does not only helped to quantify the enhanced emissions at critical locations, but it also helped to define the emission source distribution of the disrupted steady flow for further dispersion modelling. The model then was applied to estimate particle number emissions at a bidirectional bus station used by diesel and compressed natural gas fuelled buses. It was found that the acceleration distance was of critical importance when estimating particle number emission, since the highest emissions occurred in sections where most of the buses were accelerating and no significant increases were observed at locations where they idled. It was also shown that emissions at the front end of the platform were 43 times greater than at the rear of the platform. The CLSE model was also applied at a signalled pedestrian crossing, in order to assess increased particle number emissions from motor vehicles when forced to stop and accelerate from rest. The CLSE model was used to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses including 1 car travelling in 1 direction (/1 direction), 14 cars / 1 direction, 1 bus / 1 direction, 28 cars / 2 directions, 24 cars and 2 buses / 2 directions, and 20 cars and 4 buses / 2 directions. It was found that the total emissions produced during stopping on a red signal were significantly higher than when the traffic moved at a steady speed. Overall, total emissions due to the interruption of the traffic increased by a factor of 13, 11, 45, 11, 41, and 43 for the above 6 cases, respectively. In summary, this PhD thesis presents the results of a comprehensive study on particle number and mass concentration, together with particle size distribution, in a bus station transport microenvironment, influenced by bus flow rates, meteorological conditions and station design. Passenger spatial-temporal exposure to bus emitted particles was also assessed according to waiting time and location along the platform, as well as the contribution of exposure at the bus station to overall daily exposure. Due to the complexity of the interrupted traffic flow within the transport microenvironments, a unique CLSE model was also developed, which is capable of quantifying emission levels at critical locations within the transport microenvironment, for the purpose of evaluating passenger exposure and conducting simulations of vehicle emission dispersion. The application of the CLSE model at a pedestrian crossing also proved its applicability and simplicity for use in a real-world transport microenvironment.

Re-conceptualising and re-positioning Australian library and information science education for the 21st century [Final Report 2011]

How can Australian library and information science (LIS) education produce, in a sustainable manner, the diverse supply of graduates with the appropriate attributes to develop and maintain high quality professional practice in the rapidly changing 21st century? This report presents the key findings of a project that has examined this question through research into future directions for LIS education in Australia. Titled Re-conceptualising and re-positioning Australian library and information science education for the twenty-first century, the purpose of the project was to establish a consolidated and holistic picture of the Australian LIS profession, and identify how its future education and training can be mediated in a cohesive and sustainable manner. The project was undertaken with a team of 12 university and vocational LIS educators from 11 institutions around Australia between November 2009 and December 2010. Collectively, these eleven institutions represented the broad spectrum and diversity of LIS education in Australia, and enabled the project to examine education for the information profession in a holistic and synergistic manner. Participating institutions in the project included Queensland University of Technology (Project Leader), Charles Sturt University, Curtin University of Technology, Edith Cowan University, Monash University, RMIT University, University of Canberra, University of South Australia, University of Tasmania, University of Technology Sydney and Victoria University. The inception and need for the project was motivated by a range of factors. From a broad perspective several of these factors relate to concerns raised at national and international levels regarding problems with education for LIS. In addition, the motivation and need for the project also related to some unique challenges that LIS education faces in the Australian tertiary education landscape. Over recent years a range of responses to explore the various issues confronting LIS education in Australia have emerged at local and national levels however this project represented the first significant investment of funding for national research in this area. In this way, the inception of the project offered a unique opportunity and powerful mechanism through which to bring together key stakeholders and inspire discourse concerning future education for the profession. Therefore as the first national project of its kind, its intent has been to provide foundation research that will inform and guide future directions for LIS education and training in Australia. The primary objective of the project was to develop a Framework for the Education of the Information Professions in Australia. The purpose of this framework was to provide evidence based strategic recommendations that would guide Australia’s future education for the information professions. Recognising the three major and equal players in the education process the project was framed around three areas of consideration: LIS students, the LIS workforce and LIS educators. Each area of consideration aligned to a research substudy in the project. The three research substudies were titled Student Considerations, Workforce Planning Considerations and Tertiary Education Considerations. The Students substudy provided a profile of LIS students and an analysis of their choices, experiences and expectations in regard to LIS education and their graduate destinations. The Workforce substudy provided an overview and analysis of the nature of the current LIS workforce, including a focus on employer expectations and employment opportunities and comment on the core and elective skill, knowledge and attitudes of current and future LIS professionals. Finally the Tertiary Education substudy provided a profile of LIS educators and an analysis of their characteristics and experiences including the key issues and challenges. In addition it also explored current national and international trends and priorities impacting on LIS education. The project utilised a Community Based Participatory Research (CBPR) approach. This approach involves all members of the community in all aspects of the project. It recognised the unique strengths and perspectives that community members bring to the process. For this project ‘community’ comprised of all individuals who have a role in, or a vested interest in, LIS education and included LIS educators, professionals, employers, students and professional associations. Individuals from these sub-groups were invited to participate in a range of aspects of the project from design through to implementation and evaluation. A range of research methodologies were used to consider the many different perspectives of LIS education, including employers and recruiters, professional associations, students, graduates and LIS teaching staff. Data collection involved a mixed method approach of questionnaires, focus groups, semi-structured interviews and environmental scans. An array of approaches was selected to ensure that broadest possible access to different facets of the information profession would be achieved. The main findings and observations from each substudy have highlighted a range of challenges for LIS education that need to be addressed. These findings and observations have grounded the development of the Framework for the Education of the Information Professions in Australia. The framework presents eleven recommendations to progress the national approach to LIS education and guide Australia’s future education for the information professions. The framework will be used by the LIS profession, most notably its educators, as strategic directions for the future of LIS education in Australia. Framework for the Education of the Information Professions in Australia: Recommendation 1: It is recommended that a broader and more inclusive vocabulary be adopted that both recognises and celebrates the expanding landscape of the field, for example ‘information profession’, ‘information sector’, ‘information discipline’ and ‘information education’. Recommendation 2: It is recommended that a self-directed body composed of information educators be established to promote, support and lead excellence in teaching and research within the information discipline. Recommendation 3: It is recommended that Australia’s information discipline continue to develop excellence in information research that will raise the discipline’s profile and contribute to its prominence within the national and international arena. Recommendation 4: It is recommended that further research examining the nature and context of Australia’s information education programs be undertaken to ensure a sustainable and relevant future for the discipline. Recommendation 5: It is recommended that further research examining the pathways and qualifications available for entry into the Australian information sector be undertaken to ensure relevance, attractiveness, accessibility and transparency. Recommendation 6: It is recommended that strategies are developed and implemented to ensure the sustainability of the workforce of information educators. Recommendation 7: It is recommended that a national approach to promoting and marketing the information profession and thereby attracting more students to the field is developed. Recommendation 8: It is recommended that Australia’s information discipline continues to support a culture of quality teaching and learning, especially given the need to accommodate a focus on the broader information landscape and more flexible delivery options. Recommendation 9: It is recommended that strategies are developed that will support and encourage collaboration between information education within the higher education and VET sectors. Recommendation 10: It is recommended that strategies and forums are developed that will support the information sector working together to conceptualise and articulate their professional identity and educational needs. Recommendation 11: It is recommended that a research agenda be established that will identify and prioritise areas in which further development or work is needed to continue advancing information education in Australia. The key findings from this project confirm that a number of pressing issues are confronting LIS education in Australia. Left unaddressed these issues will have significant implications for the future of LIS education as well as the broader LIS profession. Consequently creating a sustainable and cohesive future can only be realised through cooperation and collaboration among all stakeholders including those with the capacity to enact radical change in university and vocational institutions. Indeed the impending adoption and implementation of the project’s recommendations will fundamentally determine whether Australian LIS education is assured both for the present day and into the future.

Moving towards a knowledge city? Brisbane's experience in knowledge-based urban development

: In the global knowledge economy, knowledge-intensive industries and knowledge workers are extensively seen as the primary factors to improve the welfare and competitiveness of cities. To attract and retain such industries and workers, cities produce knowledge-based urban development strategies, where such strategising is also an important development mechanism for cities and their economies. This paper investigates knowledge-based urban development strategies of Brisbane, Australia that support generation, attraction, and retention of investment and talent. The paper puts forward a clear understanding on the policy frameworks, and relevant applications of Brisbane’s knowledge-based urban development experience in becoming a prosperous knowledge city, and concludes by providing invaluable insights and directions for other cities seeking knowledge-based urban development.

Towards a model of dynamic capabilities in innovation-based competitive strategy : insights from project-oriented service firms

With the growing significance of services in most developed economies, there is an increased interest in the role of service innovation in service firm competitive strategy. Despite growing literature on service innovation, it remains fragmented reflecting the need for a model that captures key antecedents driving the service innovation-based competitive advantage process. Building on extant literature and using thirteen in-depth interviews with CEOs of project-oriented service firms, this paper presents a model of innovation-based competitive advantage. The emergent model suggests that entrepreneurial service firms pursuing innovation carefully select and use dynamic capabilities that enable them to achieve greater innovation and sustained competitive advantage. Our findings indicate that firms purposefully use create, extend and modify processes to build and nurture key dynamic capabilities. The paper presents a set of theoretical propositions to guide future research. Implications for theory and practice are discussed. Finally, directions for future research are outlined.

It’s not me, it’s you : a participant observation case study of the self-publishing musician in the 21st century

This thesis explores the business environment for self-publishing musicians at the end of the 20th century and the start of the 21st century from theoretical and empirical standpoints. The exploration begins by asking three research questions: what are the factors affecting the sustainability of an Independent music business; how many of those factors can be directly influenced by an Independent musician in the day-to-day operations of their musical enterprise; and how can those factors be best manipulated to maximise the benefit generated from digital music assets? It answers these questions by considering the nature of value in the music business in light of theories of political economy, then quantitative and qualitative examinations of the nature of participation in the music business, and then auto-ethnographic approaches to the application of two technologically enabled tools available to Independent musicians. By analyzing the results of five different examinations of the topic it answers each research question with reference to four sets of recurring issues that affect the operations of a 21st century music business: the musicians’ personal characteristics, their ability to address their business’s informational needs; their ability to manage the relationships upon which their business depends; and their ability to resolve the remaining technological problems that confront them. It discusses ways in which Independent self-publishing musicians can and cannot deal with these four issues on a day-to-day basis and highlights aspects for which technological solutions do not exist as well as ways in which technology is not as effective as has been claimed. It then presents a self-critique and proposes some directions for further study before concluding by suggesting some common features of 21st century Independent music businesses. This thesis makes three contributions to knowledge. First, it provides a new understanding of the sources of musical value, shows how this explains changes in the music industries over the past 30 years, and provides a framework for predicting future developments in those industries. Second, it shows how the technological discontinuity that has occurred around the start of the 21st century has and has not affected the production and distribution of digital cultural artefacts and thus the attitudes, approaches, and business prospects of Independent musicians. Third, it argues for new understandings of two methods by which self-publishing musicians can grow a business using production methods that are only beginning to be more broadly understood: home studio recording and fan-sourced production. Developed from the perspective of working musicians themselves, this thesis identifies four sets of issues that determine the probable success of musicians’ efforts to adopt new technologies to capture the value of the musicians’ creativity and thereby foster growth that will sustain an Independent music business in the 21st century.

Improving self-report measures of speeding

There is continuing debate regarding the psychometric properties of self-report measures of behaviour, particularly in road safety research. Practical considerations often preclude the use of objective assessments, leading to reliance on self-report measures. Acknowledging that such measures are likely to remain commonly used, this pilot project sought not to argue whether self-report measures should continue to be used, but to explore factors associated with how individuals respond to self-reported speeding measures. This paper reports preliminary findings from a qualitative study (focus groups and in-depth interviews) conducted with licensed drivers to explore the operational utility of self-reported speeding behaviour measures. Drawing upon concepts from the Theory of Planned Behaviour (TPB; Ajzen, 1991) and Agency Theory (Bandura, 2001), we identified four dimensions of self-reported speeding: including timeframe, speed zone, degree over the speed limit and, overall frequency of the behaviour, and examined participants’ perceptions of the operational utility of these factors. Issues related to comprehensibility, perceived accuracy, response format and layout were also explored. Results indicated that: heterogeneity in the timeframe of behavioural reflections suggests a need to provide a set timeframe for participants to consider when thinking about their previous speeding behaviour; response categories and formats should be carefully considered to ensure the most accurate representations of the frequency and degree of speeding are captured; the need to clearly articulate “low-level” speeding on self-report measures; and, that self-reports of speeding behaviour are typically context-irrelevant unless stipulated in the question. Limitations and directions for further research are discussed.