A thematic cost-benefit analysis of a marine protected area

The implementation of Marine Protected Areas (MPAs) is ultimately a social endeavour to sustain or improve human well-being via the conservation of marine ecosystems. The degree to which ecological gains are realised can depend upon how economic, ecological and social costs (negative impacts) and benefits (positive impacts) are included in the designation and management process. Without the support of key stakeholder groups whose user rights have been affected by the creation of an MPA, human impacts cannot be reduced. This study analyses a three year dataset to understand the themes associated with the economic, environmental and social costs and benefits of an MPA in Lyme Bay, United Kingdom (UK) following its establishment in 2008. Methodologically, the paper presents an ecosystem based management framework for analysing costs and benefits. Two hundred and forty one individuals were interviewed via questionnaire between 2008 and 2010 to determine perceptions and the level of support towards the MPA. Results reveal that despite the contentious manner in which this MPA was established, support for the MPA is strong amongst the majority of stakeholder groups. The level of support and the reasons given for support vary between stakeholder groups. Overall, the stakeholders perceive the social, economic and environmental benefits of the MPA to outweigh the perceived costs. There have been clear social costs of the MPA policy and these have been borne by mobile and static gear fishermen and charter boat operators. Local support for this MPA bodes well for the development of a network of MPAs around the UK coast under the United Kingdom Marine and Coastal Access Act 2009. However, this initial optimism is at risk if stakeholder expectation is not managed and the management vacuum is not filled.

Influence of Manufacturing Tolerance on Aircraft Direct Operating Cost (DOC)

The influence of manufacturing tolerance on direct operating cost (DOC) is extrapolated from an engine nacelle to be representative of an entire aircraft body. Initial manufacturing tolerance data was obtained from the shop floor at Bombardier Aerospace Shorts, Belfast while the corresponding costs were calculated according to various recurring elements such as basic labour and overtime labour, rework, concessions, and redeployment; along with the non-recurrent costs due to tooling and machinery, etc. The relation of tolerance to cost was modelled statistically so that the cost impact of tolerance change could be ascertained. It was shown that a relatively small relaxation in the assembly and fabrication tolerances of the wetted surfaces resulted in reduced costs of production that lowered aircraft DOC, as the incurred drag penalty was predicted and taken into account during the optimisation process.

Numerical Method for Cost-Weight Optimisation of Stringer-Skin Panels

The need to integrate cost into the early product definition process as an engineering parameter is addressed. The application studied is a fuselage panel that is typical for commercial transport regional jets. Consequently, a semi-empirical numerical analysis using reference data was coupled to model the structural integrity of thin-walled structures with regard to material failure and buckling: skin, stringer, flexural, and interrivet. The optimization process focuses on direct operating cost (DOC) as a function of acquisition cost and fuel burn. It was found that the ratio of acquisition cost to fuel burn was typically 4:3 and that there was a 10% improvement in the DOC for the minimal DOC condition over the minimal weight condition because of the manufacturing cost saving from having a reduced number of larger-area stringers and a slightly thicker skin than that preferred by the minimal weight condition. Also note that the minimal manufacturing cost condition was slightly better than the minimal weight condition, which highlights the key finding: The traditional minimal weight condition is a dated and suboptimal approach to airframe structural design.

Integrating Aircraft Cost Modelling into Conceptual Design

The article presents cost modeling results from the application of the Genetic-Causal cost modeling principle. Industrial results from redesign are also presented to verify the opportunity for early concept cost optimization by using Genetic-Causal cost drivers to guide the conceptual design process for structural assemblies. The acquisition cost is considered through the modeling of the recurring unit cost and non-recurring design cost. The operational cost is modeled relative to acquisition cost and fuel burn for predominately metal or composites designs. The main contribution of this study is the application of the Genetic-Causal principle to the modeling of cost, helping to understand how conceptual design parameters impact on cost, and linking that to customer requirements and life cycle cost.

Cost Estimation of Machined Parts within an Aerospace Supply Chain

A generic, hierarchical, and multifidelity unit cost of acquisition estimating methodology for outside production machined parts is presented. The originality of the work lies with the method’s inherent capability of being able to generate multilevel and multifidelity cost relations for large volumes of parts utilizing process, supply chain costing data, and varying degrees of part design definition information. Estimates can be generated throughout the life cycle of a part using different grades of the combined information available. Considering design development for a given part, additional design definition may be used as it becomes available within the developed method to improve the quality of the resulting estimate. Via a process of analogous classification, parts are classified into groups of increasing similarity using design-based descriptors. A parametric estimating method is then applied to each subgroup of the machined part commodity in the direction of improved classification and using which, a relationship which links design variables to manufacturing cycle time may be generated. A rate cost reflective of the supply chain is then applied to the cycle time estimate for a given part to arrive at an estimate of make cost which is then totalled with the material and treatments cost components respectively to give an overall estimate of unit acquisition cost. Both the rate charge applied and the treatments cost calculated for a given procured part is derived via the use of ratio analysis.