Estratigrafia sismica do cenozóico na plataforma continental algarvia: interpretação do controle tectónico da sedimentação

The interpretation of 64 seismic reflection profiles in the Algarve continental platform (36º 20'-37º 00' paralels and 7º 20'-8º 40' meridians) calibrated with five petroleum exploration wells, with the identification of the geometric relations between six Cenozoic seismic units (B to G) and tectonic structures, allowed the construction of sucessive time-isopach maps (twt/s) and detailed interpretation of the geologic evolution. Two major tectonic structures were identified: a) the Portimão-Monchique fracture zone (striking N-S); b) an off-shore NW-SE fault zone, probably the S. Marcos-Quarteira fault. This accident separates two tectonic domains: the western domain (with N-S and E-W predominant structures and, secondarily, NW-SE and NE-SW) and the eastern domain (dominated by WSW-ENE, NW-SE, NE-SW, NNE-SSW and NNW-SSE structures). A persistent halokinetic activity had two major moments: a) sin-C unit; b) sin- and post-E unit. An increasing flexuration of the margin was identified, with spacial and temporal variation of the subsidence. The tectonic regime is considered as generally compressive, but the interpretation of the successíve stress-fields is rendered dificult by the existence of tectonic sub-domains and evaporitic structures.

The three main marine depositional cycles of the Neogene of Portugal

The present work follows a stratigraphic model for the marine Neogene of Portugal based on the definition of three main marine sedimentary cycles. Conceptually the I, II and III Neogene Cycles can be defined as 2nd order sedimentary sequences with duration ranging from 5 to 8 Ma. The I Neogene Cycle is fully represented only in the Lower Tagus Basin. Ranging from the Early Aquitanian to the Late Burdigalian the I Neogene Cycle testify a transgressive episode in the region of Lisbon and Setúbal Peninsula. Rapid lateral facies variations suggest a shallowmarine basin. This cycle ends with an important Late Burdigalian tectonic compressive event expressed by uplift of the surrounding areas and deformation affecting the Early Miocene deposits of the Arrábida Chain. The II Neogene Cycle includes thick sedimentary sequences covering Paleozoic and Mesozoic formations in the Algarve and Alvalade-Melides regions and it extends as far north as Santarém in the Lower Tagus Basin. Mainly controlled by global eustasy, it was generated by the important positive eustatic trend that characterized the Middle Miocene worldwide to which the Portuguese continental margin acted more or less passively. This cycle ended with a second and the most important compression event starting after the end of the Serravallian affecting the entire Portuguese onshore and shelf areas. This led to an important depositional hiatus of marine sediments for more than 2.5 Ma. During the Early and the Middle Tortonian occurred the clockwise rotation of the Guadalquivir Basin. The thickmarine units deposited afterwards in this basin produced a litostatic load, which seems to have induced subsidence farther west resuming the Neogene marine sedimentation in the Cacela region (Eastern Algarve), during the Late Tortonian. This marks the beginning of the III Neogene Cycle. To the north, in the Sado Basin (Alvalade-Melides region), a similar depositional sequence starts its sedimentation during the Messinian. Further north, in the Pombal-Caldas da Rainha region, marine sedimentation started during the Late Pliocene (Piacenzian). The migration in time, from south to north for the beginning of the marine sedimentation of this cycle is interpreted as reflecting a visco-elastic propagation of the deformation from the Betic chain northwards.

Choosing amine-based absorbents for CO2 capture

CO2 capture from gaseous effluents is one of the great challenges faced by chemical and environmental engineers, as the increase in CO2 levels in the Earth atmosphere might be responsible for dramatic climate changes. From the existing capture technologies, the only proven and mature technology is chemical absorption using aqueous amine solutions. However, bearing in mind that this process is somewhat expensive, it is important to choose the most efficient and, at the same time, the least expensive solvents. For this purpose, a pilot test facility was assembled and includes an absorption column, as well as a stripping column, a heat exchanger between the two columns, a reboiler for the stripping column, pumping systems, surge tanks and all necessary instrumentation and control systems. Some different aquous amine solutions were tested on this facility and it was found that, from a set of six tested amines, diethanol amine is the one that turned out to be the most economical choice, as it showed a higher CO2 loading capacity (0.982 mol of CO2 per mol of amine) and the lowest price per litre (25.70 ¤/L), even when compared with monoethanolamine, the benchmark solvent, exhibiting a price per litre of 30.50 ¤/L.

The use of the boundary element method in the analysis of single lap joints

The most common techniques for stress analysis/strength prediction of adhesive joints involve analytical or numerical methods such as the Finite Element Method (FEM). However, the Boundary Element Method (BEM) is an alternative numerical technique that has been successfully applied for the solution of a wide variety of engineering problems. This work evaluates the applicability of the boundary elem ent code BEASY as a design tool to analyze adhesive joints. The linearity of peak shear and peel stresses with the applied displacement is studied and compared between BEASY and the analytical model of Frostig et al., considering a bonded single-lap joint under tensile loading. The BEM results are also compared with FEM in terms of stress distributions. To evaluate the mesh convergence of BEASY, the influence of the mesh refinement on peak shear and peel stress distributions is assessed. Joint stress predictions are carried out numerically in BEASY and ABAQUS®, and analytically by the models of Volkersen, Goland, and Reissner and Frostig et al. The failure loads for each model are compared with experimental results. The preparation, processing, and mesh creation times are compared for all models. BEASY results presented a good agreement with the conventional methods.

A case study undertaken recycling & reuse of glass fiber reinforced thermoset polumer wastes of composite materials industry

Glass fibre-reinforced plastics (GFRP) have been considered inherently difficult to recycle due to both: crosslinked nature of thermoset resins, which cannot be remoulded, and complex composition of the composite itself. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. In this study, efforts were made in order to recycle grinded GFRP waste, proceeding from pultrusion production scrap, into new and sustainable composite materials. For this purpose, GFRP waste recyclates, were incorporated into polyester based mortars as fine aggregate and filler replacements at different load contents and particle size distributions. Potential recycling solution was assessed by mechanical behaviour of resultant GFRP waste modified polymer mortars. Results revealed that GFRP waste filled polymer mortars present improved flexural and compressive behaviour over unmodified polyester based mortars, thus indicating the feasibility of the GFRP industrial waste reuse into concrete-polymer composite materials.

Pozzolanic activity of oil-refining catalyst: evaluation by electron and atomic microscopy

The reuse of waste fluid catalytic cracking (FCC) catalyst as partial surrogate for cement can reduce the environmental impact of both the oil-refinery and cement production industries [1,2]. FCC catalysts can be considered as pozzolanic materials since in the presence of water they tend to chemically react with calcium hydroxide to produce compounds possessing cementitious properties [3,4]. In addition, partial replacement of cement with FCC catalysts can enhance the performance of pastes and mortars, namely by improving their compressive strength [5,6]. In the present work the reaction of waste FCC catalyst with Ca(OH)2 has been investigated after a curing time of 28 days by scanning electron microscopy (SEM) with electron backscattered signal (BSE) combined with X-ray energy dispersive spectroscopy (EDS) carried out with a JEOL JSM 7001F instrument operated at 15 kV coupled to an INCA pentaFetx3 Oxford spectrometer. The polished cross-sections of FCC particles embedded in resin have also been evaluated by atomic force microscopy (AFM) in contact mode (CM) using a NanoSurf EasyScan 2 instrument. The SEM/EDS results revealed that an inward migration of Ca occurred during the reaction. A weaker outward migration of Si and Al was also apparent (Fig. 1). The migration of Ca was not homogeneous and tended to follow high-diffusivity paths within the porous waste FCC catalyst particles. The present study suggests that the porosity of waste FCC catalysts is key for the migration/reaction of Ca from the surrounding matrix, playing an important role in the pozzolanic activity of the system. The topography images and surface roughness parameters obtained by atomic force microscopy can be used to infer the local porosity in waste FCC catalyst particles (Fig. 2).

Estruturas de Suporte de Terras Executadas com Pneus - Modelo à Escala Reduzida

Mestrado em Engenharia Civil – Ramo de Estruturas

Influence of the crushing process of recycled aggregates on concrete properties

This work intends to evaluate the (mechanical and durability) performance of concrete made with coarse recycled concrete aggregates (CRCA) obtained using two crushing processes: primary crushing (PC) and primary plus secondary crushing (PSC). This analysis intends to select the most efficient production process of recycled aggregates (RA). The RA used here resulted from precast products (P), with strength classes of 20 MPa, 45 MPa and 65 MPa, and from laboratory-made concrete (L) with the same compressive strengths. The evaluation of concrete was made with the following tests: compressive strength; splitting tensile strength; modulus of elasticity; carbona-tion resistance; chloride penetration resistance; capillary water absorption; and water absorption by immersion. These findings contribute to a solid and innovative basis that allows the precasting industry to use without restrictions the waste it generates. © (2015) Trans Tech Publications, Switzerland.

Performance of concrete made with recycled aggregates from Portuguese CDW recycling plants

The objective of this research is the production of concrete with recycled aggregates (RA) from various CDW plants around Portugal. The influence of the RA collection location and consequently of their composition on the characteristics of the concrete produced was analysed. In the mixes produced in this research RA from five plants (Valnor, Vimajas, Ambilei, Europontal and Retria) were used: in three of them coarse and fine RA were analysed and in the remaining ones only coarse RA were used. The experimental campaign comprised two tests in fresh concrete (cone of Abrams slump and density) and eight in hardened concrete (compressive strength in cubes and cylinders, splitting tensile strength, modulus of elasticity, water absorption by immersion and capillarity, carbonation and chloride penetration resistance). It was found that the use of RA causes a quality decrease in concrete. However, there was a wide results scatter according to the plant where the RAs were collected, because of the variation in composition of the RA. It was also found that the use of fine RA causes a more significant performance loss of the concrete properties analysed than the use of coarse RA. © (2015) Trans Tech Publications, Switzerland.

Identificação, avaliação e controlo de riscos numa empresa da indústria dos colchões

Relatório de Estágio

Transporte marítimo de curta distância na União Europeia e em Portugal

O transporte marítimo sempre assumiu uma importância primordial no transporte, quer de pessoas como de mercadorias. O uso das vias marítimas para o transporte de mercadorias é uma prática utilizada desde os tempos antigos. O transporte marítimo na Europa sempre foi uma forma eficaz e de baixo custo de transportar passageiros e mercadorias de um local para outro. Atualmente, todos os modos de transporte necessitam de melhorar a sua eficiência e reduzir o montante de poluentes que libertam para o meio-ambiente. O transporte marítimo de curta distância (TMCD) é parte essencial no sistema de transporte multimodal Europeu representando cerca de 37% das transações intracomunitárias (tkm). Os resultados alcançados advêm desde que, em 2001, a European Shortsea Network (ESN) em parceria com os Shortsea Promotion Centres (SPC) de cada Estado-Membro da União Europeia (EU) conseguiram efetuar progressos significativos na promoção e desenvolvimento do transporte por esta via. Esta tese de mestrado pretende caraterizar o TMCD na EU e em Portugal e a sua articulação com os outros meios de transporte de mercadorias. Será também analisada a situação Portuguesa ao nível do transporte marítimo de mercadorias fazendo especial relevância à mercadoria contentorizada, às infraestruturas atualmente existentes em Portugal assim como às perspetivas futuras para o setor. A metodologia utilizada inclui a revisão de literatura da investigação efetuada sobre o setor, a recolha de informação primária através do instrumento inquérito e a recolha de informação estatística a partir de fontes secundárias, permitindo a caraterização do setor. O inquérito foi desenvolvido e partilhado com mais de um milhar de empresas a operar em Portugal, nas que se incluem as empresas transportadoras, operadores logísticos, agentes de navegação e as principais empresas exportadoras/importadoras a operar em Portugal, tendo-se obtido 106 respostas válidas. A nível nacional, o inquérito realizado permitiu confirmar que os principais portos logísticos para a movimentação internacional de mercadorias são os portos de Leixões, Lisboa, Sines e Setúbal, estando a maioria das empresas inquiridas localizadas no hinterland destes portos. O inquérito permitiu também concluir que o facto de o transporte rodoviário ser um meio de transporte rápido, de baixo custo para curtas e médias distâncias, de elevada frequência de transporte, de oferecer elevada capacidade e diversos tipos de carga transportada, de oferecer serviços Porta-a-Porta, da elevada flexibilidade e mobilidade oferecida, assim como a rapidez das operações de carga e descarga continuam a contribuir para a elevada competitividade deste modo de transporte de mercadorias, sendo as razões pelo qual este modo é escolhido, pese embora, ser o modo mais poluente por tonelada transportada. Os modos de transporte TMCD e ferroviário apenas são alvo de escolha, como modo de transporte de mercadorias, por parte das empresas mais responsáveis socialmente e ambiental. O inquérito permitiu ainda concluir que, para haver uma melhor articulação entre o TMCD com outros meios de transporte, é necessário que sejam disponibilizados novos serviços, portos e terminais logísticos com serviços privatizados, assim como a redução das tarifas aplicáveis TMCD.

Tectónica da região de Sintra

Photo-interpretation of aerial stereopairs of the Sintra region on the approx. 1/32 000 scale together with field work allowed the production of the present Tectonic Map of the Sintra region. It is now possible to separate structures which resulted from two different tectonic events: one, corresponding to the intrusion of the Late Cretaceous Sintra igneous diapir, and the other the Miocene compressive event, the most important tectonic inversion phase of the Lusitanian Basin. The former are present to the south, southeast and east of the intrusion and within the intrusion itself, affecting the peripheral granites and their contacts with the gabbro-syenite core. These structures comprehend: i) faults and conical fractures striking parallel to the massif boundary, which were intruded by dykes, ii) vertical faults and fractures of two conjugate sets, dextral NNW-SSE and sinistral NNE-SSW. These faults are certainly associated with the E-W striking massif's northwards directed thrust and indicate a N-S oriented horizontal maximum compressive stress. The Miocene compressive event reactivated most of the inherited structures as follows. The NNWSSE faults located on the Sintra southern platform were reactivated as dextral strike slip faults and the E-W thrust along the northern boundary of the massif was also reactivated. This thrust propagated to the east. It also enhanced the asymmetry of the rim-syncline, uplifted the massif and reactivated the NNE-SSW faults as sinistral lateral ramps, which also accommodated vertical throw. The present Tectonic Map of Sintra together with the available geophysical data (MOREIRA, 1984, KULLBERG et al., 1991, SILVA & MIRANDA, 1994) allowed reassessment of the models proposed for the emplacement of the Sintra, Sines and Monchique igneous massifs, which intruded during Late Cretaceous times along the deep dextral NNW-SSE oriented strike slip fault (RIBEIRO et al., 1979; TERRINHA, 1998; TERRINHA & KULLBERG, 1998).

Interpretação tectónica de um conjunto de lineamentos WNW-ESE observados em imagens landsat da margem oeste ibérica

The existence of satellite images ofthe West Iberian Margin allowed comparative study of images as a tool applied to structural geology. Interpretation of LANDSAT images of the Lusitanian Basin domain showed the existence of a not previously described WNW-ESE trending set oflineaments. These lineaments are persistent and only observable on small scale images (e.g. approx. 11200000 and 11500 000) with various radiometric characteristics. They are approximately 20 km long, trend l200±15° and cross cut any other families oflineaments. The fact that these lineaments are perpendicular to the Quaternary thrusts of the Lower Tagus Valley and also because they show no off-set across them, suggests that they resulted from intersection oflarge tensile fractures on the earth's surface. It is proposed in this work that these lineaments formed on a crustal flexure of tens ofkm long, associated with the Quaternary WNW-ESE oriented maximum compressive stress on the West Iberian Margin. The maximum compressive stress rotated anticlockwise from a NW -SE orientation to approximately WNW-ESE, from Late Miocene to Quaternary times (RIBEIRO et aI., 1996). Field inspection of the lineaments revealed zones of norm~1.J. faulting and cataclasis, which are coincident with the lineaments and affect sediments of upper Miocene up to Quaternary age. These deformation structures show localized extension perpendicular to the lineaments, i.e. perpendicular to the maximum compressive direction, after recent stress data along the West Portuguese Margin (CABRAL & RIBEIRO, 1989; RIBEIRO et at., 1996). Also, on a first approach, the geographical distribution of these lineaments correlates well with earthquake epicenters and areas of largest Quaternary Vertical Movements within the inverted Lusitanian Basin (CABRAL, 1995).

Stress Ratio Effects on the fatigue Properties of Biaxially Loaded Tubular FRP-Specimens – Experimental Study

In this work tubular fiber reinforced specimens are tested for fatigue life. The specimens are biaxially loaded with tension and shear stresses, with a load angle β of 30° and 60° and a load ratio of R=0,1. There are many factors that affect fatigue life of a fiber reinforced material and the main goal of this work is to study the effects of load ratio R by obtaining S-N curves and compare them to the previous works (1). All the other parameters, such as specimen production, fatigue loading frequency and temperature, will be the same as for the previous tests. For every specimen, stiffness, temperature of the specimen during testing, crack counting and final fracture mode are obtained. Prior to testing, a study if the literature regarding the load ratio effects on composites fatigue life and with that review estimate the initial stresses to be applied in testing. In previous works (1) similar specimens have only been tested for a load ratio of R=-1 and therefore the behaviour of this tubular specimens for a different load ratio is unknown. All the data acquired will be analysed and compared to the previous works, emphasizing the differences found and discussing the possible explanations for those differences. The crack counting software, developed at the institute, has shown useful before, however different adjustments to the software parameters lead to different cracks numbers for the same picture, and therefore a better methodology will be discussed to improve the crack counting results. After the specimen’s failure, all the data will be collected and stored and fibre volume content for every specimen is also determinate. The number of tests required to make the S-N curves are obtained according to the existent standards. Additionally are also identified some improvements to the testing machine setup and to the procedures for future testing.

Vibration control with shape-memory alloys in civil engineering structures

Dissertação apresentada à Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Doutor em Engenharia Civil