Characterization of conducting polymer coated synthetic fabrics for heat generation

Heat generation in fabrics coated with the conductive polymer polypyrrole was investigated. The PET fabrics were coated by chemical synthesis using four different oxidizing agent–dopant combinations. The samples from the four different dopant systems all show an increase in temperature when a fixed voltage is applied to the fabric. The antraquinone-2-sulfonic acid (AQSA) sodium salt doped polypyrrole coating was the most effective in heat generation whereas the sodium perchlorate dopant system was the least effective. The power density per unit area achieved in polypyrrole coated polyester–Lycra® fabric with 0.027 mol/l of AQSA acting as dopant was 430 W/m². The power density per unit area achieved for the sodium perchlorate system, using the same synthesis conditions, was 55 W/m².

Characterization of superfine wool powder/poly(propylene) blend film

Superfine wool powder was blended and extruded with poly(propylene) (PP) to produce blend pellets, and the extruded pellets were hot-pressed into a blend film. SEM photographs show that the powder could be uniformly incorporated with PP after extrusion. FT-IR spectra shows that no substantial changes occurred in the chemical structure of both PP and wool powder in the blend film. X-Ray diffraction analysis indicates that crystallinity of the blend film was much higher than that of the wool powder and little lower than that of PP. TG-tested results indicate that the thermal stability of the blend film declined with an increase in the powder content. Endothermic peaks of the wool powder in the blend film become more obvious as the powder content increases. Mechanical properties decline greatly with an increase in the wool powder content in the blend film.

Inorganic-organic hybrids of the p,p'-diphenylmethylenediphosphinate, pcp2-. synthesis, characterization and XRPD structures of [Sn(pcp)] and [Cu(pcp)]

Two new inorganic-organic polymeric hybrids [Sn(pcp)] and [Cu(pcp)], pcp = CH₂(PhPO₂)₂^2-, have been synthesized and structurally chracterized. The tin derivative has been obtained by reaction of the p,p'-diphenylmethylenediphosphinic acid (H₂pcp) in water with SnCl₂·2H₂O, while the copper derivative has been synthesized through a hydrothermal reaction from the same H₂pcp acid and Cu(O₂CMe)₂·H₂O. The structures of these compounds have been solved "ab initio" by X-ray powder diffraction (XRPD) data. [Sn(pcp)] has a ladder-like polymeric structure, with tin(II) centers bridged by diphenylmethylenediphosphinate ligands, and alternating six- and eight-membered rings. The hemilectic coordination around the metal shows the tin(II) lone pair to be operative, resulting in significant interaction mainly with a C-C bond of one phenyl ring. The [Cu(pcp)] complex displays a polymeric columnar structure formed by two intersecting sinusoidal ribbons of copper(II) ions bridged by the bifunctional phosphinate ligands. The intersections of the ribbons are made of dimeric units of pentacoordinated copper ions. Crystal data for [Sn(pcp)]: monoclinic, space group P2₁Ic, a = 11.2851(1), b = 15.4495(6), c = 8.6830(1) Å, ^β= 107.546(1)°, V = 1443.44(9) Å, Z = 4. Crystal data for [Cu(pcp)]: triclinic, space group P, a = 10.7126(4), b = 13.0719(4), c = 4.9272(3) Å, α= 92.067(5), β= 95.902(7), γ= 87.847(4)°, V = 685.47(7), Z = 2. The tin compound has been characterized by ¹¹⁹Sn MAS NMR (magic-angle spinning NMR), revealing asymmetry in the valence electron cloud about tin. Low-temperature magnetic measurements of the copper compound have indicated the presence of weak antiferromagnetic interactions below 50 K.

Characterization of conducting polymer coated fabrics at microwave frequencies

Purpose – The purpose of this paper is to investigate microwave reflection, transmission, and complex permittivity of p-toluene-2-sulfonic acid doped conducting polypyrrole coated nylon-lycra textiles in the 1-18?GHz frequency with a view to potential applications in the interaction of electromagnetic radiation with such coated fabrics.

Design/methodology/approach – The chemical polymerization of pyrrole is achieved by an oxidant, ferric chloride and doped with p-toluene sulfonic acid (pTSA) to enhance the conductivity and improve stability. Permittivity of the conducting textile substrates is performed using a free space transmission method accompanied by a mathematical diffraction reduction method.

Findings – The real part of permittivity increases with polymerization time and dopant concentration, reaching a plateau at certain dopant concentration and polymerization time. The imaginary part of permittivity shows a frequency dependent change throughout the test range. All the samples have higher values of absorption than reflection. The total electromagnetic shielding effectiveness exceeds 80 percent for the highly pTSA doped samples coated for 3?h.

Originality/value – A non-contact, non-destructive free space method thin flexible specimens to be tested with high accuracy across large frequency range. The non-destructive nature of the experiments enables investigation of the stability of the microwave transmission, reflection, absorption and complex permittivity values. Moreover, mathematical removal of the diffraction enables higher accuracy.

Characterization of hot-pressed films from superfine wool powder

In this study, superfine wool powder was plasticized with glycerol and hot-pressed into a film. Scanning electron microscopy photos showed that the superfine wool powder could be molded into a smooth film and that the wool powder was distributed evenly in the cross section of the film. Fourier transform infrared analysis revealed no substantial changes in the chemical structure of the wool powder after hot pressing, but the absorbing peaks of glycerol were found in the spectrum. X-ray diffraction analysis showed that the overall crystallinity increased after the wool powder was hot-pressed into film. Thermogravimetry (TG) analysis indicated that the thermal stability of the hot-pressed film decreased. A transition point appeared in the TG curve of the wool hot-pressed film as glycerol was added. The differential thermal analysis curve of the film showed sharp absorbing peaks similar to that of wool powder. With increasing glycerol content, the film showed increasing ductility and softness.

Micro- and nano-characterization of membrane materials

The global warming has led to enormous challenges worldwide for a large variety of communities, particularly these associated to water and water treatment industry. Due to increasing scarcity of water resources, the development of new membrane materials and water treatment processes will play an important role in tackling this emerging problem. In this paper, the recent development in characterization of in particular, geometrical parameters of micro- and nano-membrane materials will be reviewed. Membranes with micro- and nano-pores have widely been used for ultrafiltration and nanofiltration. The structure of the pores and the surface of the pores/membranes may be optimized to achieve much improved flow rate in these micro-/nano-channels. Therefore, accurate characterization of porous structures will contribute significantly to the prediction of membrane performance. It will not only provide an insight into the new characterization methods but also the development of novel materials.

Characterization of the drug binding specificity of rat liver fatty acid binding protein

Liver-fatty acid binding protein (L-FABP) is found in high levels in enterocytes and is involved in the cytosolic solubilization of fatty acids during fat absorption. In the current studies, the interaction of L-FABP with a range of lipophilic drugs has been evaluated to explore the potential for L-FABP to provide an analogous function during the absorption of lipophilic drugs. Binding affinity for L-FABP was assessed by displacement of a fluorescent marker, 1-anilinonaphthalene-8-sulfonic acid (ANS), and the binding site location was determined via nuclear magnetic resonance chemical shift perturbation studies. It was found that the majority of drugs bound to L-FABP at two sites, with the internal site generally having a higher affinity for the compounds tested. Furthermore, in contrast to the interaction of L-FABP with fatty acids, it was demonstrated that a terminal carboxylate is not required for specific binding of lipophilic drugs at the internal site of L-FABP.

Preparation, characterization and dielectric properties of temperature stable SrTiO3/PEEK composites for microwave substrate applications

Poly(ether ether ketone) (PEEK) is a potential candidate for electronic applications due to its low permittivity, low loss, high melting point, better chemical resistance, excellent insulating properties and easy processibility. Present paper discusses the preparation and characterization of SrTiO3 filled PEEK composite for microwave substrate applications. The dielectric constant, dielectric loss and temperature variation of dielectric constant of the composites have been studied up to 1 MHz using an Impedance Analyzer. Different theoretical approaches have been employed to predict the effective permittivity of composite systems and the results are compared with that of the experimental data. The crystallinity of the bulk composite is studied by X-ray diffraction studies. Scanning electron microscopic technique has been employed to study the dispersion of the particulate filler in PEEK matrix. Vickers hardness of pure and filled PEEK composite has been measured using Microhardness Tester. The effect of particle size on the dielectric as well as mechanical properties of SrTiO3/PEEK composite system is also studied by incorporating micronsize and nanosize fillers. Present study shows that a temperature stable composite can be realized by judiciously selecting appropriate filler concentration in the PEEK matrix.

Structural characterization of novel ionic materials incorporating the bis(trifluoromethanesulfonyl)amide anion

A range of low melting salts of the bis(trifluoromethanesulfonyl)amide (TFSA) anion with hindered organic cations (N-methyl-1-methylpyrrolinium, N,N-dimethylpyrrolidinium, N,N,N,-trimethylammonium, and N,N,N,N-tetrakis(n-propyl)ammonium) have been crystallized. Single-crystal X-ray diffraction data show these materials to consist of discrete ions with only weak C−H···O (or for Me₃NH N−H···O) contacts between the constituent atoms of the cations and anions close to the limits of van der Waals separations. Consequently, the observed physical properties of these materials presumably result from the diffuse negative charge on the TFSA anion and inefficient packing of these large and irregularly shaped ions.

New insights into the fundamental chemical nature of ionic liquid film formation on magnesium alloy surfaces

Ionic liquids (ILs) based on trihexyltetradecylphosphonium coupled with either diphenylphosphate or bis(trifluoromethanesulfonyl)amide have been shown to react with magnesium alloy surfaces, leading to the formation a surface film that can improve the corrosion resistance of the alloy. The morphology and microstructure of the magnesium surface seems critical in determining the nature of the interphase, with grain boundary phases and intermetallics within the grain, rich in zirconium and zinc, showing almost no interaction with the IL and thereby resulting in a heterogeneous surface film. This has been explained, on the basis of solid-state NMR evidence, as being due to the extremely low reactivity of the native oxide films on the intermetallics (ZrO₂ and ZnO) with the IL as compared with the magnesium-rich matrix where a magnesium hydroxide and/or carbonate inorganic surface is likely. Solid-state NMR characterization of the ZE41 alloy surface treated with the IL based on (Tf)₂N− indicates that this anion reacts to form a metal fluoride rich surface in addition to an organic component. The diphenylphosphate anion also seems to undergo an additional chemical process on the metal surface, indicating that film formation on the metal is not a simple chemical interaction between the components of the IL and the substrate but may involve electrochemical processes.

Solid state NMR characterization of polyrrole : the nature of the dopant in PF6− doped films

³¹P and ¹⁹F solid state NMR have been used to study the nature of the PF₆− anion in polypyrrole films at various levels of oxidation. It appears that the symmetric PF₆− unit remains undistorted and unchanged throughout, suggesting that it is predominantly acting only as a counterion and not as a true ‘dopant’, since any distortion in the phosphorous environments would result at the very least in chemical shift anisotropy of the ³¹P nucleus. A second set of phosphorous and fluorine resonances, which are consistent with a difluoride phosphorous compound, appeared in the films. Upon electrochemical reduction of the polymer, the undistorted PF₆− anion leaves the film whereas the second phosphorous species remains. Re-oxidation of the polymer reverses the processes observed during reduction.

Preparation and characterization on cellulose nanofiber film

In this study, cellulose nanofibers were obtained from wood pulp using a chemo-mechanical method and thin films were made of these cellulose nanofibers. The morphology of the films was studied by scanning electron microscopy (SEM). SEM image analysis revealed that the films were composed of cellulose nanofibers with an average diameter of around 32 nm. Other properties were also characterized, including the degree of crystallinity by X-ray diffraction, chemical bonding by infrared attenuated total reflectance analysis, and thermal properties by differential scanning calorimetry. The foldable, strong, and optically translucent cellulose nanofiber films thus obtained have many potential applications as micro/nano electronic devices, biosensors and filtration media, etc.

Thermal and chemical properties of wool powders

Wool powders with different particle sizes were examined in terms of their crystal structures, thermal properties, surface chemical compositions and moisture regains. It was found that the crystallinity of wool powders was increased, and the moisture regains were decreased as the particle sizes of wool powders were reduced. For comparison, the properties of activated charcoal were also investigated. The higher dye uptake of activated charcoal at pH 10. compared to that of wool powder, could be due to its greater surface area and porous structure.

Synthesis, characterization, and multilayer assembly of pH sensitive graphene−polymer nanocomposites

pH sensitive graphene−polymer composites have been prepared by the modification of graphene basal planes with pyrene-terminated poly(2-N,N′-(dimethyl amino ethyl acrylate) (PDMAEA) and poly(acrylic acid) (PAA) via π−π stacking. The pyrene-terminal PDMAEA and PAA were synthesized using reversible addition−fragmentation chain transfer (RAFT) polymerization with a pyrene-functional RAFT agent. The graphene−polymer composites were found to demonstrate phase transfer behavior between aqueous and organic media at different pH values. Atomic force microscopy (AFM) analysis revealed that the thicknesses of the graphene−polymer sheets were approximately 3.0 nm when prepared using PDMAEA (M_n: 6800 and PDI: 1.12). The surface coverage of polymer chains on the graphene basal plane was calculated to be 5.3 × 10⁻¹¹ mol cm⁻² for PDMAEA and 1.3 × 10⁻¹⁰ mol cm⁻² for PAA. The graphene−polymer composites were successfully characterized using X-ray photoelectron spectroscopy (XPS), attenuated total reflection infrared (ATR-IR) spectroscopy, and thermogravimetric analysis (TGA). Self-assembly of the two oppositely charged graphene−polymer composites afforded layer-by-layer (LbL) structures as evidenced by high-resolution scanning electron microscopy (SEM) and quartz crystal microbalance (QCM) measurements.

Synthesis, X-ray structure and electrochemical characterization of palladium(II) bearing ferrocenyldiphenylphosphine complexes

Four new complexes, [PdX(κ2-2-C6R4PPh2)(PPh2Fc)] [X = Br, R = H (1), R = F (2); X = I, R = H (3), R = F (4)], containing ferrocenyldiphenylphosphine (PPh2Fc) have been prepared and fully characterised. The X-ray structures of complexes trans-1, cis-2 and cis-4, and that of a decomposition product of 4, [Pd(κ2-2-C6F4PPh2)(μ-I)(μ-2-C6F4PPh2)PdI(PPh2Fc)] (5), have been determined. These complexes show a distorted square planar geometry about the metal atom, the bite angles of the chelate ligands being about 69°, as expected. The cis/trans ratio of 1–4 in solution is strongly dependent on solvent. The new complexes and the uncoordinated PPh2Fc ligand were electrochemically characterised by cyclic and rotating disk voltammetry, UV-visible spectroelectrochemistry, and bulk electrolysis in dichloromethane and acetonitrile. In both cases, oxidation occurs at both the ferrocene and phosphine centres, but the complexes oxidise at more positive potentials than uncoordinated PPh2Fc; subsequently, the metal–phosphorus bond is cleaved, leading to free PPh2Fc+, which undergoes further chemical and electrochemical reactions.