Analytical Elastic Stiffness Model for 3D Woven Orthogonal Interlock Composites

This research presents the development of an analytical model to predict the elastic stiffness performance of orthogonal interlock bound 3D woven composites as a consequence of altering the weaving parameters and constituent material types. The present approach formulates expressions at the micro level with the aim of calculating more representative volume fractions of a group of elements to the layer. The rationale in representing the volume fractions within the unit cell more accurately was to improve the elastic stiffness predictions compared to existing analytical modelling approaches. The models developed in this work show good agreement between experimental data and improvement on existing predicted values by models published in literature.

Teaching and Learning Guide for 'Modern Problems of Editing...'

Companion piece to my earlier article in Literature Conmpass: 'Modern Problems of Editing: The Two Texts of Doctor Faustus'. Provides a model for a module based on the topic of that article.

Barrier height variations and interface properties of PtSi/Si structures

To study some of the interfacial properties of PtSi/Si diodes, Schottky structures were fabricated on (100) crystalline silicon substrates by conventional thermal evaporation of Pt on Si followed by annealing at different temperatures (from 400 degrees C to 700 degrees C) to form PtSi. The PtSi/n-Si diodes, all yielded Schottky barrier (SB) heights that are remarkably temperature dependent. The temperature range (20-290 K) over which the I-V characteristics were measured in the present study is broader with a much lower limit (20 K), than what is usually reported in literature. These variations in the barrier height are adequately interpreted by introducing spatial inhomogeneity into the barrier potential with a Gaussian distribution having a mean barrier of 0.76 eV and a standard deviation of 30 meV. Multi-frequency capacitance-voltage measurements suggest that the barrier is primarily controlled by the properties of the silicide-silicon interface. The forward C-V characteristics, in particular, show small peaks at low frequencies that can be ascribed to interface states rather than to a series resistance effect.

Oxidized Recombinant Human Growth Hormone That Maintains Conformational Integrity

Chemical degradations often induce changes in protein conformation and thus influence protein activity and protein stability in solutions. One difficulty in studying of chemical degradations on protein aqueous properties is to obtain sufficient amount of chemically degraded protein which is well characterized. Chemical degradation protocols that are often used may induce also conformation changes and aggregation of the protein. In this article we studied the effect of methionine oxidation on the conformation of recombinant human growth hormone (r-hGH). In literature it is reported that oxidation of methionine residues induces conformation changes on r-hGH. In our study, oxidation of r-hGH was performed by incubation with hydrogen peroxide under mild conditions. Mass spectrometry and chromatographic analysis revealed that oxidation with hydrogen peroxide resulted in more than 90% of oxidized r-hGH. By extensive spectroscopic characterizations no detectable change in conformation and aggregation of r-hGH after oxidation was found. In conclusion, mild oxidation conditions led to selective oxidation of the two more accessible methionine residues of r-hGH (Met(14) and Met(125)) and did not results in any conformation change of the protein. These findings prove that oxidation of human growth hormone does not influence protein conformation and demonstrate the importance of employing mild conditions during production of oxidized protein. (C) 2010 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 100:110-122, 2011

JPEG encoder system-on-a-chip demonstrator

The design of a System-on-a-Chip (SoC) demonstrator for a baseline JPEG encoder core is presented. This combines a highly optimized Discrete Cosine Transform (DCT) and quantization unit with an entropy coder which has been realized using off-the-shelf synthesizable IP cores (Run-length coder, Huffman coder and data packer). When synthesized in a 0.35 µm CMOS process, the core can operate at speeds up to 100 MHz and contains 50 k gates plus 11.5 kbits of RAM. This is approximately 20% less than similar JPEG encoder designs reported in literature. When targeted at FPGA the core can operate up to 30 MHz and is capable of compressing 9-bit full-frame color input data at NTSC or PAL rates.

Horizontal Descemet's membrane break due to birth trauma

We report an unusual case of horizontal corneal Descemet's membrane break due to birth trauma. The patient had a difficult birth with trauma to her right eye and poor vision. However unlike the reports in literature, which describe these breaks to have a characteristic vertical or vertically oblique orientation in birth trauma, the breaks in our patient were horizontal. No other cause was found for these Descemet's breaks.

Effect of impeller speed on mechanical and dissolution properties of high-shear granules

Impeller speed is one of the most crucial process variables that affect the properties of the granules produced in a high-shear granulator. Several reports can be found in literature that discuss the influence of impeller speed on the granules size. For instance some researchers like Knight report an increase of granule size with impeller speed [1] and [2], while others (Scheaefer et al. and Ramaker et al.) observed a decrease of granules size with increasing impeller speed [3] and [4]. However there is limited work reported in literature on the effect of the impeller speed on the mechanical properties of granules. Mechanical properties are important as they affect the performance of the granules on the other downstream process such as transportation and handling. The work reported here serves to address the missing in knowledge gap regarding the influence of impeller speed on mechanical properties granules. How the granulation system responds to the changes in the impeller speeds depends on binder that is used in the process. For this reason the two extreme cases, of a low viscosity binder system and high viscosity binder system are considered in this research. For low viscosity binder system it was observed that the granule size decreased with increasing impeller speed whilst for the high viscosity binder system the opposite was observed by Knight [1]. The granule strength, the Young's modulus and yield strength of the high viscosity granules increased with increasing impeller speed where as the opposite trends were observed for the low viscosity binder granules.

Detailed validation of an automotive catalysis model using spatially resolved measurements within the catalyst substrate

Many kinetic models have appeared in literature in past decades using two main approaches: the traditional global kinetics approach, or the more complex micro-kinetics approach. Whether global or micro-kinetics, kinetic models have been based on experimental data obtained at the end of the monolith. The experimental procedure using end pipe analysis may give an accurate overview of the reaction mechanisms that occur; however, the lack of information from within the catalyst can ultimately lead to inaccuracies in the kinetic model and parameters used.

Using SpaciMS, a spatially resolved experimental technique developed at the Queen's University Belfast, information from within the catalyst can be obtained. This minimally invasive technique provides detailed information of the gas concentration and temperature profile from inside the catalytic monolith. This paper presents a kinetic model and simulations validated against experimental data obtained from three positions inside the catalyst monolith at 2, 14, and 26 mm in, using data from the SpaciMS. Also, simulations of end pipe analysis, using a commercial reactor, for the CO oxidation are presented and analyzed. The simulations presented are for varying concentrations of both CO and O2 (0.5 % and 1 % CO, 0.5 % and 2 % O2) for both the global and micro-kinetic approach.

Evaluating environmental enrichment options for commercial broiler chickens

Implications Provision of environmental enrichment in line with that required by welfare-based quality assurance schemesdoes not always appear to lead to clear improvements in broiler chicken welfare. This research perhaps serves to highlightthe deficit in information regarding the ‘real world’ implications of enrichment with perches, string and straw bales.

Introduction Earlier work showed that provision of natural light and straw bales improved leg health in commercial broilerchickens (Bailie et al., 2013). This research aimed to determine if additional welfare benefits were shown in windowedhouses by increasing straw bale provision (Study 1), or by providing perches and string in addition to straw bales (Study 2).

Material and methods Commercial windowed houses in Northern Ireland containing ~23,000 broiler chickens (placed inhouses as hatched) were used in this research which took place in 2011. In Study 1 two houses on a single farm wereassigned to one of two treatments: (1) 30 straw bales per house (1 bale/44m2), or (2) 45 straw bales per house (1bale/29m2). Bales of wheat straw, each measuring 80cm x 40cm x 40cm were provided from day 10 of the rearing cycle,as in Bailie et al. (2013). Treatments were replicated over 6 production cycles (using 276,000 Ross 308 and Cobb birds),and were swapped between houses in each replicate. In Study 2, four houses on a single farm were assigned to 1 of 4treatments in a 2 x 2 factorial design. Treatments involved 2 levels of access to perches (present (24/house), or absent), and2 levels of access to string (present (24/house), or absent), and both types of enrichment were provided from the start of thecycle. Each perch consisted of a horizontal, wooden beam (300 cm x 5 cm x 5cm) with a rounded upper edge resting on 2supports (15 cm high). In the string treatment, 6 pieces of white nylon string (60 cm x 10 mm) were tied at their mid-pointto the wire above each of 4 feeder lines. Thirty straw bales were also provided per house from day 10. This study wasreplicated over 4 production cycles using 368,000 Ross 308 birds. In both studies behaviour was observed between 0900and 1800 hours in weeks 3-5 of the cycle. In Study 1, 8 focal birds were selected in each house each week, and generalactivity, exploratory and social behaviours recorded directly for 10 minutes. In Study 2, 10 minute video recordings weremade of 6 different areas (that did not contain enrichment) of each house each week. The percentage of birds engaged inlocomotion or standing was determined through scan sampling these recordings at 120 second intervals. Four perches andfour pieces of string were filmed for 25 mins in each house that contained these enrichments on one day per week. The totalnumber of times the perch or string was used was recorded, along with the duration of each bout. In both studies, gaitscores (0 (perfect) to 5 (unable to walk)) and latency to lie (measured in seconds from when a bird had been encouraged tostand) were recorded in 25 birds in each house each week. Farm and abattoir records were also used in both studies todetermine the number of birds culled for leg and other problems, mortality levels, slaughter weights, and levels of pododermatitis and hock burn. Data were analysed using SPSS (version 20.0) and treatment and age effects on behaviouralparameters were determined in normally distributed data using ANOVA (‘Straw bale density*week’, or‘string*perches*week’ as appropriate), and in non-normally distributed data using Kuskall-Wallace tests (P<0.05 forsignificance) . Treatment (but not age) effects on performance and health data were determined using the same testsdepending on normality of data.

Results Average slaughter weight, and levels of mortality, culling, hock burn and pododermatitis were not affected bytreatment in either study (P<0.05). In Study 1 straw bale (SB) density had no significant effect on the frequency orduration of behaviours including standing, walking, ground pecking, dust bathing, pecking at bales or aggression, or onaverage gait score (P>0.05). However, the average latency to lie was greater when fewer SB were provided (30SB 23.38s,45SB 18.62s, P<0.01). In Study 2 there was an interaction between perches (Pe) and age in lying behaviour, with higherpercentages of birds observed lying in the Pe treatment during weeks 4 and 5 (week 3 +Pe 77.0 -Pe 80.9, week 4 +Pe 79.5 -Pe 75.2, week 5 +Pe 78.4 -Pe 76.2, P<0.02). There was also a significant interaction between string (S) and age inlocomotory behaviour, with higher percentages of birds observed in locomotion in the string treatment during week 3 butnot weeks 4 and 5 (week 3 +S 4.9 -S 3.9, week 4 +S 3.3 -S 3.7, week 5 +S 2.6 -S 2.8, P<0.04). There was also aninteraction between S and age in average gait scores, with lower gait scores in the string treatment in weeks 3 and 5 (week3: +S 0.7, -S 0.9, week 4: +S 1.5, -S 1.4, week 5: +S 1.9, -S 2.0, P<0.05). On average per 25 min observation there were15.1 (±13.6) bouts of perching and 19.2 (±14.08) bouts of string pecking, lasting 117.4 (±92.7) and 4.2 (±2.0) s for perchesand string, respectively.

Conclusion Increasing straw bale levels from 1 bale/44m2 to 1 bale/29m2 floor space does not appear to lead to significantimprovements in the welfare of broilers in windowed houses. The frequent use of perches and string suggests that thesestimuli have the potential to improve welfare. Provision of string also appeared to positively influence walking ability.However, this effect was numerically small, was only shown in certain weeks and was not reflected in the latency to lie.Further research on optimum design and level of provision of enrichment items for broiler chickens is warranted. Thisshould include measures of overall levels of activity (both in the vicinity of, and away from, enrichment items).

Accounting for clean, fast and high yielding reactions under microwave conditions

Thermal reactions proceed optimally when they are rapidly heated to the highest tolerable temperature, held there for the shortest possible time and then quenched. This is explained through assessments of reaction kinetics in literature examples and models. Although presently available microwave equipment is better suited to rapid heating than resistance-heated systems, the findings do not depend upon the method of heating. Claims that microwave heated reactions proceed faster and more cleanly than their conventionally heated counterparts are valid only when comparably rapid heating and cooling cannot be obtained by conventional heating. These findings suggest that rigid adherence to the sixth principle of green chemistry, relating to the use of ambient temperature and pressure, may not always afford optimal results. © 2010 The Royal Society of Chemistry.

An Evaluation of 1D Loss Model Collections for the Off-Design Performance Prediction of an Automotive Turbocharger Compressor

Abstract. Single-zone modelling is used to assess different collections of impeller 1D loss models. Three collections of loss models have been identified in literature, and the background to each of these collections is discussed. Each collection is evaluated using three modern automotive turbocharger style centrifugal compressors; comparisons of performance for each of the collections are made. An empirical data set taken from standard hot gas stand tests for each turbocharger is used as a baseline for comparison. Compressor range is predicted in this study; impeller diffusion ratio is shown to be a useful method of predicting compressor surge in 1D, and choke is predicted using basic compressible flow theory. The compressor designer can use this as a guide to identify the most compatible collection of losses for turbocharger compressor design applications. The analysis indicates the most appropriate collection for the design of automotive turbocharger centrifugal compressors.

Finite Element Analysis of the Enhanced Strength of Laterally Restrained RC Slabs

This paper presents the numerical simulation of the ultimate behaviour of 85 one-way and two-way spanning laterally restrained concrete slabs of variable thickness, span, reinforcement ratio, strength and boundary conditions reported in literature by different authors. The developed numerical model was described and all the assumptions were illustrated. ABAQUS, a Finite Element Analysis suite of software, was employed. Non-linear implicit static general analysis method offered by ABAQUS was used. Other analysis methods were also discussed in general in terms of application such as Explicit Dynamic Analysis and Riks method. The aim is to demonstrate the ability and efficacy of FEA to simulate the ultimate load behaviour of slabs considering different material properties and boundary conditions. The authors intended to present a numerical model that provides consistent predictions of the ultimate behaviour of laterally restrained slabs that could be used as an alternative for expensive real life testing as well as for the design and assessment of new and existing structures respectively. The enhanced strength of laterally-restrained slabs compared with conventional design methods predictions is believed to be due to compressive membrane action (CMA). CMA is an inherent phenomenon of laterally restrained concrete beams/slabs. The numerical predictions obtained from the developed model were in good correlation with the experimental results and with those obtained from the CMA method developed at the Queen’s University Belfast, UK.

Operators for Similarity Search: Semantics, Techniques and Usage Scenarios

This book provides a comprehensive tutorial on similarity operators. The authors systematically survey the set of similarity operators, primarily focusing on their semantics, while also touching upon mechanisms for processing them effectively.

The book starts off by providing introductory material on similarity search systems, highlighting the central role of similarity operators in such systems. This is followed by a systematic categorized overview of the variety of similarity operators that have been proposed in literature over the last two decades, including advanced operators such as RkNN, Reverse k-Ranks, Skyline k-Groups and K-N-Match. Since indexing is a core technology in the practical implementation of similarity operators, various indexing mechanisms are summarized. Finally, current research challenges are outlined, so as to enable interested readers to identify potential directions for future investigations.

In summary, this book offers a comprehensive overview of the field of similarity search operators, allowing readers to understand the area of similarity operators as it stands today, and in addition providing them with the background needed to understand recent novel approaches.