An Experimental Study on Flame Propagation in Cornstarch Dust Clouds

Following the quantitative determination of dust cloud parameters, this study investigates the flame propagation through cornstarch dust clouds in a vertical duct of 780 mm height and 160 x 160 mm square cross section, and gives particular attention to the effect of small scale turbulence and small turbulence intensity on flame characteristics. Dust suspensions in air were produced using an improved apparatus ensuring more uniform distribution and repeatable dust concentrations in the testing duct. The dispersion-induced turbulence was measured by means of a particle image velocimetry (PIV) system, and dust concentrations were estimated by direct weighing method. This quantitative assessment made it possible to correlate observed flame behaviors with the parameters of the dust cloud. Upward propagating dust flames, from both closed/open bottom end to open/closed top end of the duct, were visualized by direct light and shadow photography. From the observation of propagation regimes and the measurements of flame velocity, a critical value of the turbulence intensity can be specified below which laminar flame propagation would be established. This transition condition was determined to be 10 cm/s. Laminar flames propagated with oscillations from the closed bottom end to the open top end of the testing duct, while the turbulent flames accelerated continuously. Both laminar and turbulent flames propagated with steady velocity from the open bottom end to the closed top end of the duct. The measured propagation velocity of laminar flames appeared to be in the range of 0.45-0.56 m/s, and it was consistent with the measurements reported in the literature. In the present experimental study, the influence of dust concentration on flame propagation was also examined, and the flame propagation velocity was found weakly sensitive to the variations in dust concentration. Some information on the flame structure was revealed from the shadow records, showing the typical heterogeneous feature of the dust combustion process.

On Selecting the excess temperature to minimize the entrainment mortality rate

In selecting an excess temperature at which to operate a power plant cooling system it has been customary to consider only thermal stresses and to use the ratio of the number of organisms killed to the number of organisms entrained. This frequently leads to the selection of a low excess temperature, AT, which, in turn, requires a large volume flow of cooling water. When mortalities due to physical and chemical stresses are included and the total number of entrained organisms killed is taken as the measure of the environmental damage, it becomes evident that the choice of a low excess temperature is seldom, if ever, best.

Modified Simplified Rate Equation Model of Flowing Chemical Oxygen-Iodine Laser and its Application

A modified simplified rate equation (RE) model of flowing chemical oxygen-iodine laser (COIL), which is adapted to both the condition of homogeneous broadening and inhomogeneous broadening being of importance and the condition of inhomogeneous broadening being predominant, is presented for performance analyses of a COIL. By using the Voigt profile function and the gain-equal-loss approximation, a gain expression has been deduced from the rate equations of upper and lower level laser species. This gain expression is adapted to the conditions of very low gas pressure up to quite high pressure and can deal with the condition of lasing frequency being not equal to the central one of spectral profile. The expressions of output power and extraction efficiency in a flowing COIL can be obtained by solving the coupling equations of the deduced gain expression and the energy equation which expresses the complete transformation of the energy stored in singlet delta state oxygen into laser energy. By using these expressions, the RotoCOIL experiment is simulated, and obtained results agree well with experiment data. Effects of various adjustable parameters on the performances of COIL are also presented.

Shock-Induced Dust Cloud Over a Deposit Layer of Fine Particles

The present paper investigates particle density pro les of a dust cloud induced by a normal shock wave moving at a constant speed along a at surface deposited with ne particles. In shock-fixxed coordinates, numerical simulation of ow structures of the carrier- and dispersed- phases was performed for the M = 2 case. The neness and non-uniformity of the particle size are taken into account and their effcts on the dust cloud are discussed in detail.

Mechanical properties and constitutive relationships of 30CrMnSiA steel heated at high rate

In this paper, the mechanical behavior of 30CrMnSiA steel after heating at a high rate are investigated experimentally and theoretically, including a detailed discussion of the effects of strain rate and temperature. Two constitutive models are presented to describe the mechanical response of this material after heating at a high rate, and verified by experimental results. (C) 2007 Elsevier B.V. All rights reserved.

A method for estimating the rate of shedding of tags from yellowfin tuna

ENGLISH: The present paper describes a new method for estimating the shedding rate of tags. The method utilizes not only data on tagging and recovery of fish marked with two tags but also data from those marked with one. One important advantage of the new technique is that the estimates of the shedding rates are free from distortion caused by variations in fishing intensity during the total recovery period. The idea of this method appears to be implicit in a short note by Gulland (1963). This technique has been applied to the data obtained by the Inter-American Tropical Tuna Commission in a tagging cruise off the west coast of southern Baja California, during June 1963, at which time both single and double-tagged yellowfin tuna were released. Details of the tagging procedure and equipment have been described by Fink (1965b). The results presented in the present paper are for yellowfin tuna tagged with dart tags. Estimates of shedding should be made separately for each species investigated and also for each type of tag used, since these rates may be variable and often unexpectedly high (Springer and McErlean 1961, Chadwick 1963). SPANISH: El presente estudio describe un nuevo método para estimar las tasas del desprendimiento de marcas. El método emplea no solamente los datos sobre la marcación y recobro de peces marcados con dos marcas, pero también datos de los peces marcados con una marca. Una ventaja importante de la nueva técnica, es que las estimaciones de las tasas de desprendimiento son libres de alteración, causada por las variaciones en la intensidad de pesca durante el período total de recobro. La idea de este método parece ser implícita en un breve apunte por Gulland (1963). Esta técnica se ha aplicado a los datos obtenidos por la Comisión Interamericana del Atún Tropical, en un crucero de marcación efectuado frente a la costa occidental al sur de Baja California, en junio de 1963, tiempo en el cual fueron liberados atunes aleta amarilla marcados tanto con una como con dos marcas. Los detalles del procedimiento de la marcación y del equipo usado han sido descritos por Fink (1965b). Los resultados presentados en este estudio, pertenecen al atún aleta amarilla marcado con marcas de dardo. Las estimaciones del desprendimiento deben efectuarse separadamente para cada especie que ha sido investigada y también para cada tipo de marca usado, ya que estas tasas pueden ser vaiables, y a menudo inesperadamente altas (Springer y McErlean 1961, Chadwick 1963). (PDF contains 20 pages.)

Distribución de "coxiella burnetii" en los rumiantes domésticos y en la fauna silvestre de la Comunidad Atutónoma Vasca. Evaluacióndel efecto del tratamiento antibiótico y de la vacunación en el control de la fiebre Q en rebaños ovinos naturalmente infectados

243 p. : il.