Assessment of flood-related recharge to alluvial aquifers of an irrigated catchment following extended drought conditions using 3D visualisation and environmental tracers, Lockyer Valley, southeast Queensland, Australia.

The Lockyer Valley in southeast Queensland, Australia, hosts an economically significant alluvial aquifer system which has been impacted by prolonged drought conditions (~1997 to ~ 2009). Throughout this time, the system was under continued groundwater extraction, resulting in severe aquifer depletion. By 2008, much of the aquifer was at <30% of storage but some relief occurred with rains in early 2009. However, between December 2010 and January 2011, most of southeast Queensland experienced unprecedented flooding, which generated significant aquifer recharge. In order to understand the spatial and temporal controls of groundwater recharge in the alluvium, a detailed 3D lithological property model of gravels, sands and clays was developed using GOCAD software. The spatial distribution of recharge throughout the catchment was assessed using hydrograph data from about 400 groundwater observation wells screened at the base of the alluvium. Water levels from these bores were integrated into a catchment-wide 3D geological model using the 3D geological modelling software GOCAD; the model highlights the complexity of recharge mechanisms. To support this analysis, groundwater tracers (e.g. major and minor ions, stable isotopes, 3H and 14C) were used as independent verification. The use of these complementary methods has allowed the identification of zones where alluvial recharge primarily occurs from stream water during episodic flood events. However, the study also demonstrates that in some sections of the alluvium, rainfall recharge and discharge from the underlying basement into the alluvium are the primary recharge mechanisms of the alluvium. This is indicated by the absence of any response to the flood, as well as the observed old radiocarbon ages and distinct basement water chemistry signatures at these locations. Within the 3D geological model, integration of water chemistry and time-series displays of water level surfaces before and after the flood suggests that the spatial variations of the flood response in the alluvium are primarily controlled by the valley morphology and lithological variations within the alluvium. The integration of time-series of groundwater level surfaces in the 3D geological model also enables the quantification of the volumetric change of groundwater stored in the unconfined sections of this alluvial aquifer during drought and following flood events. The 3D representation and analysis of hydraulic and recharge information has considerable advantages over the traditional 2D approach. For example, while many studies focus on singular aspects of catchment dynamics and groundwater-surface water interactions, the 3D approach is capable of integrating multiple types of information (topography, geological, hydraulic, water chemistry and spatial) into a single representation which provides valuable insights into the major factors controlling aquifer processes.

Review of 3D model development with application to groundwater studies in New Zealand 1996 – 2011

Three dimensional geological modelling techniques have been applied since 1996 with an aim to characterise the lithological and chronological units of New Zealand’s many diverse aquifers. Models of property-scattered data have also been applied to assess physical properties of aquifers and the distribution of groundwater chemistry, including groundwater age, to inform an understanding of groundwater systems. These models, fundamental to understanding groundwater recharge, flow and discharge have found many uses as outlined in this paper.

Understanding hydrochemical processes using 3D models and hydrochemical facies in Wairau Plain groundwater, Marlborough

Three dimensional models and groundwater quality are combined to better understand and conceptualise groundwater systems in complex geological settings in the Wairau Plain, Marlborough. Hydrochemical facies, which are characteristic of distinct evolutionary pathways and a common hydrologic history of groundwaters, are identified within geological formations to assess natural water-rock interactions, redox potential and human agricultural impact on groundwater quality in the Wairau Plain.

Assessment of interactions between alluvial, Great Artesian Basin (GAB) and volcanic aquifers using 3D visualisation and environmental tracers, Lockyer Valley, southeast Queensland, Australia

A detailed 3D lithological model framework was developed using GOCAD software to understand interactions between alluvial, volcanic and GAB aquifers and the spatial and temporal distribution of groundwater recharge to the alluvium of the Lockyer Valley. Groundwater chemistry, isotope data (H20-δ2H and δ18O , 87Sr/86Sr, 3H and 14C) and groundwater level time-series data from approximately 550 observation wells were integrated into the catchment-wide 3D model to assess the recharge processes involved. This approach enabled the identification of zones where recharge to the alluvium primarily occurs from stream water during episodic flood events. Importantly, the study also demonstrates that in some sections of the alluvium recharge is also from storm rainfall and seepage discharge from the underlying GAB aquifers. These other sources of recharge are indicated by (a) the absence of a response of groundwater levels to flooding in some areas, (b) old radiocarbon ages, and (c) distinct bedrock water chemistry and δ2H and δ18O signatures in alluvial groundwater at these locations. Integration of isotopes, water chemistry and time-series displays of groundwater levels before and after the 2010/2011 flood into the 3D model suggest that the spatial variations in the alluvial groundwater response are mostly controlled by valley morphology and lithological (i.e. permeability) variations within the alluvium. Examination of the groundwater level variations in the 3D model also enabled quantification of the volumetric change of groundwater stored in the unconfined alluvial aquifer prior to and post-flood events.

Managing distraction in 21st century learning environments

First year students attend face-to-face classes armed with an arsenal of internet enabled digital devices. The conundrum is that while these devices offer scope for enhancing opportunities for engagement in face-to-face learning, they may simultaneously distract students away from learning and compound isolation issues. This paper considers how to best to use these devices for maximum engagement in first year face-to-face learning so as to assist students in connecting with other learners and instructors within the learning environment

First international workshop on theory and applications of process visualization

The representation of business process models has been a continuing research topic for many years now. However, many process model representations have not developed beyond minimally interactive 2D icon-based representations of directed graphs and networks, with little or no annotation for information over- lays. With the rise of desktop computers and commodity mobile devices capable of supporting rich interactive 3D environments, we believe that much of the research performed in computer human interaction, virtual reality, games and interactive entertainment has much potential in areas of BPM; to engage, pro- vide insight, and to promote collaboration amongst analysts and stakeholders alike. This initial visualization workshop seeks to initiate the development of a high quality international forum to present and discuss research in this field. Via this workshop, we intend to create a community to unify and nurture the development of process visualization topics as a continuing research area.

The impacts of power outages on the residents of contemporary multistorey apartment buildings in subtropical environments

With significant population growth experienced in South East Queensland over the past two decades and a high rate of growth expected to continue in coming decades, the Queensland Government is promoting urban consolidation planning policies to manage growth sustainably. Multi-residential buildings will play an important role in facilitating the increased densities which urban consolidation policies imply. However, a major flood event in January 2011 has brought to light the vulnerability of certain types of multi-residential typologies to power outages. The crisis conditions exposed how contemporary building design and construction practices, coupled with regulatory and planning issues, appear to have compromised the resilience and habitability of multi-storey residential buildings. In the greater urban area of Brisbane, Queensland, the debilitating dependence that certain types of apartment buildings have on mains electricity was highlighted by residents’ experiences of the Brisbane River flood disaster, before, during and after the event. This research examined high density residential buildings in West End, Brisbane, an inner city suburb which was severely affected by the flood and is earmarked for significant urban densification under the Brisbane City Plan. Medium-to-high-density residential buildings in the suburb were mapped in flooded and non-flooded locations and a database containing information about the buildings was created. Parameters included date of construction, number of storeys, systems of access and circulation, and potential for access to natural light and ventilation for habitable areas. A series of semi-structured interviews were conducted with residents involved in the owners’ management committees of several buildings to verify information the mapping could not provide. The interviews identified a number of critical systems failures due to power outage which had a significant impact on residents’ wellbeing, comfort and safety. Building services such as lifts, running water, fire alarms, security systems and air-conditioning ceased to operate when power was disconnected to neighbourhoods and buildings in anticipation of rising flood waters. Lack of access to buildings and dwellings, lack of safety, lack of building security, and lack of thermal comfort affected many residents whether or not their buildings were actually subjected to inundation, with some buildings rendered uninhabitable for a prolonged period. The extent of the impact on residents was dramatically influenced by the scale and type of building inhabited, with those dwelling in buildings under a 25m height limit, with a single lift, found to be most affected. The energy-dependency and strong trend of increasing power demands of high-rise buildings is well-documented. Extended electricity outages such as the one brought about by the 2011 flood in Queensland are likely to happen more frequently than the 50-year average of the flood event itself. Electricity blackouts can result from a number of man-made or natural causes, including shortages caused by demand exceeding supply. This paper highlights the vulnerability of energy-dependent buildings to power outages and investigates options for energy security for occupants of multi-storey buildings and makes recommendations to increase resilience and general liveability in multi-residential buildings in the subtropics through design modifications.

Extending Web Modeling Language to exploit stigmergy : intentionally recording unintentional trails

Software development and Web site development techniques have evolved significantly over the past 20 years. The relatively young Web Application development area has borrowed heavily from traditional software development methodologies primarily due to the similarities in areas of data persistence and User Interface (UI) design. Recent developments in this area propose a new Web Modeling Language (WebML) to facilitate the nuances specific to Web development. WebML is one of a number of implementations designed to enable modeling of web site interaction flows while being extendable to accommodate new features in Web site development into the future. Our research aims to extend WebML with a focus on stigmergy which is a biological term originally used to describe coordination between insects. We see design features in existing Web sites that mimic stigmergic mechanisms as part of the UI. We believe that we can synthesize and embed stigmergy in Web 2.0 sites. This paper focuses on the sub-topic of site UI design and stigmergic mechanism designs required to achieve this.

Exploration and reflection in interactive art : glass pond

Glass Pond is an interactive artwork designed to engender exploration and reflection through an intuitive, tangible interface and a simulation agent. It is being developed using iterative methods. A study has been conducted with the aim of illuminating user experience, interface, design, and performance issues.The paper describes the study methodology and process of data analysis including coding schemes for cognitive states and movements. Analysis reveals that exploration and reflection occurred as well as composing behaviours (unexpected). Results also show that participants interacted to varying degrees. Design discussion includes the artwork's (novel) interface and configuration.

Network interactions and performance of a multi-function IEC 61850 process bus

New substation technology, such as non-conventional instrument transformers,and a need to reduce design and construction costs, are driving the adoption of Ethernet based digital process bus networks for high voltage substations. Protection and control applications can share a process bus, making more efficient use of the network infrastructure. This paper classifies and defines performance requirements for the protocols used in a process bus on the basis of application. These include GOOSE, SNMP and IEC 61850-9-2 sampled values. A method, based on the Multiple Spanning Tree Protocol (MSTP) and virtual local area networks, is presented that separates management and monitoring traffic from the rest of the process bus. A quantitative investigation of the interaction between various protocols used in a process bus is described. These tests also validate the effectiveness of the MSTP based traffic segregation method. While this paper focusses on a substation automation network, the results are applicable to other real-time industrial networks that implement multiple protocols. High volume sampled value data and time-critical circuit breaker tripping commands do not interact on a full duplex switched Ethernet network, even under very high network load conditions. This enables an efficient digital network to replace a large number of conventional analog connections between control rooms and high voltage switchyards.

Fatalism, superstition, religion, and culture : road user beliefs and behaviour in Pakistan

Road traffic crashes have emerged as a major health problem around the world. Road crash fatalities and injuries have been reduced significantly in developed countries, but they are still an issue in low and middle-income countries. The World Health Organization (WHO, 2009) estimates that the death toll from road crashes in low- and middle-income nations is more than 1 million people per year, or about 90% of the global road toll, even though these countries only account for 48% of the world's vehicles. Furthermore, it is estimated that approximately 265,000 people die every year in road crashes in South Asian countries and Pakistan stands out with 41,494 approximately deaths per year. Pakistan has the highest rate of fatalities per 100,000 population in the region and its road crash fatality rate of 25.3 per 100,000 population is more than three times that of Australia's. High numbers of road crashes not only cause pain and suffering to the population at large, but are also a serious drain on the country's economy, which Pakistan can ill-afford. Most studies identify human factors as the main set of contributing factors to road crashes, well ahead of road environment and vehicle factors. In developing countries especially, attention and resources are required in order to improve things such as vehicle roadworthiness and poor road infrastructure. However, attention to human factors is also critical. Human factors which contribute to crashes include high risk behaviours like speeding and drink driving, and neglect of protective behaviours such as helmet wearing and seat belt wearing. Much research has been devoted to the attitudes, beliefs and perceptions which contribute to these behaviours and omissions, in order to develop interventions aimed at increasing safer road use behaviours and thereby reducing crashes. However, less progress has been made in addressing human factors contributing to crashes in developing countries as compared to the many improvements in road environments and vehicle standards, and this is especially true of fatalistic beliefs and behaviours. This is a significant omission, since in different cultures in developing countries there are strong worldviews in which predestination persists as a central idea, i.e. that one's life (and death) and other events have been mapped out and are predetermined. Fatalism refers to a particular way in which people regard the events that occur in their lives, usually expressed as a belief that an individual does not have personal control over circumstances and that their lives are determined through a divine or powerful external agency (Hazen & Ehiri, 2006). These views are at odds with the dominant themes of modern health promotion movements, and present significant challenges for health advocates who aim to avert road crashes and diminish their consequences. The limited literature on fatalism reveals that it is not a simple concept, with religion, culture, superstition, experience, education and degree of perceived control of one's life all being implicated in accounts of fatalism. One distinction in the literature that seems promising is the distinction between empirical and theological fatalism, although there are areas of uncertainty about how well-defined the distinction between these types of fatalism is. Research into road safety in Pakistan is scarce, as is the case for other South Asian countries. From the review of the literature conducted, it is clear that the descriptions given of the different belief systems in developing countries including Pakistan are not entirely helpful for health promotion purposes and that further research is warranted on the influence of fatalism, superstition and other related beliefs in road safety. Based on the information available, a conceptual framework is developed as a means of structuring and focusing the research and analysis. The framework is focused on the influence of fatalism, superstition, religion and culture on beliefs about crashes and road user behaviour. Accordingly, this research aims to provide an understanding of the operation of fatalism and related beliefs in Pakistan to assist in the development and implementation of effective and culturally appropriate interventions. The research examines the influence of fatalism, superstition, religious and cultural beliefs on risky road use in Pakistan and is guided by three research questions: 1. What are the perceptions of road crash causation in Pakistan, in particular the role of fatalism, superstition, religious and cultural beliefs? 2. How does fatalism, superstition, and religious and cultural beliefs influence road user behaviour in Pakistan? 3. Do fatalism, superstition, and religious and cultural beliefs work as obstacles to road safety interventions in Pakistan? To address these questions, a qualitative research methodology was developed. The research focused on gathering data through individual in-depth interviewing using a semi-structured interview format. A sample of 30 participants was interviewed in Pakistan in the cities of Lahore, Rawalpindi and Islamabad. The participants included policy makers (with responsibility for traffic law), experienced police officers, religious orators, professional drivers (truck, bus and taxi) and general drivers selected through a combination of purposive, criterion and snowball sampling. The transcripts were translated from Urdu and analysed using a thematic analysis approach guided by the conceptual framework. The findings were divided into four areas: attribution of crash causation to fatalism; attribution of road crashes to beliefs about superstition and malicious acts; beliefs about road crash causation linked to popular concepts of religion; and implications for behaviour, safety and enforcement. Fatalism was almost universally evident, and expressed in a number of ways. Fate was used to rationalise fatal crashes using the argument that the people killed were destined to die that day, one way or another. Related to this was the sense of either not being fully in control of the vehicle, or not needing to take safety precautions, because crashes were predestined anyway. A variety of superstitious-based crash attributions and coping methods to deal with road crashes were also found, such as belief in the role of the evil eye in contributing to road crashes and the use of black magic by rivals or enemies as a crash cause. There were also beliefs related to popular conceptions of religion, such as the role of crashes as a test of life or a source of martyrdom. However, superstitions did not appear to be an alternative to religious beliefs. Fate appeared as the 'default attribution' for a crash when all other explanations failed to account for the incident. This pervasive belief was utilised to justify risky road use behaviour and to resist messages about preventive measures. There was a strong religious underpinning to the statement of fatalistic beliefs (this reflects popular conceptions of Islam rather than scholarly interpretations), but also an overlap with superstitious and other culturally and religious-based beliefs which have longer-standing roots in Pakistani culture. A particular issue which is explored in more detail is the way in which these beliefs and their interpretation within Pakistani society contributed to poor police reporting of crashes. The pervasive nature of fatalistic beliefs in Pakistan affects road user behaviour by supporting continued risk taking behaviour on the road, and by interfering with public health messages about behaviours which would reduce the risk of traffic crashes. The widespread influence of these beliefs on the ways that people respond to traffic crashes and the death of family members contribute to low crash reporting rates and to a system which appears difficult to change. Fate also appeared to be a major contributing factor to non-reporting of road crashes. There also appeared to be a relationship between police enforcement and (lack of) awareness of road rules. It also appears likely that beliefs can influence police work, especially in the case of road crash investigation and the development of strategies. It is anticipated that the findings could be used as a blueprint for the design of interventions aimed at influencing broad-spectrum health attitudes and practices among the communities where fatalism is prevalent. The findings have also identified aspects of beliefs that have complex social implications when designing and piloting driver intervention strategies. By understanding attitudes and behaviours related to fatalism, superstition and other related concepts, it should be possible to improve the education of general road users, such that they are less likely to attribute road crashes to chance, fate, or superstition. This study also underscores the understanding of this issue in high echelons of society (e.g., policy makers, senior police officers) as their role is vital in dispelling road users' misconceptions about the risks of road crashes. The promotion of an evidence or scientifically-based approach to road user behaviour and road safety is recommended, along with improved professional education for police and policy makers.

A multi-stage history for carbonaceous material in extraterrestrial chondritic porous aggregate W7029*A and a new cosmothermometer

A new set of primitive extraterrestrial materials collected in the Earth's stratosphere include Chondritic Porous Aggregates (CPA's) [1]. CPAs have a complex and variable mineralogy [1-3] that include 'organic compounds' [4,5] and poorly graphitised carbon (PGC)[6]. This study presents a continuation of our detailed Analytical Electron Microscope study on carbon-rich CPA W7029*A from the JSC Cosmic Dust Collection. This CPA is an uncontaminated sample that survived atmospheric entry without appreciable alteration [7] and which contains ~44% carbonaceous material. The carbonaceous composition of selected particles was confirmed by Electron Energy Loss Spectroscopy and Selected Area Electron Diffraction (SAED). Possible carbonaceous contaminants introduced by specimen preparation techniques are easily recognised from indigenous CPA carbon particles [8] and do not bias our interpretations.

The smart skies project : enabling technologies for future airspace environments

This paper summarises the achievements of the Smart Skies Project, a three-year, multi-award winning international project that researched, developed and extensively flight tested four enabling aviation technologies: an electrooptical mid-air collision avoidance system, a static obstacle avoidance system, a mobile ground-based air traffic surveillance system, and a global automated airspace separation management system. The project included the development of manned and unmanned flight test aircraft, which were used to characterise the performance of the prototype systems for a range of realistic scenarios under a variety of environmental conditions. In addition to the collection of invaluable flight data, the project achieved world-firsts in the demonstration of future automated collision avoidance and separation management concepts. This paper summarises these outcomes, the overall objectives of the project, the research and the development of the prototype systems, the engineering of the flight test systems, and the results obtained from flight-testing.

Custom digital workflows : a new framework for design analysis integration

Flexible information exchange is critical to successful design-analysis integration, but current top-down, standards-based and model-oriented strategies impose restrictions that contradicts this flexibility. In this article we present a bottom-up, user-controlled and process-oriented approach to linking design and analysis applications that is more responsive to the varied needs of designers and design teams. Drawing on research into scientific workflows, we present a framework for integration that capitalises on advances in cloud computing to connect discrete tools via flexible and distributed process networks. We then discuss how a shared mapping process that is flexible and user friendly supports non-programmers in creating these custom connections. Adopting a services-oriented system architecture, we propose a web-based platform that enables data, semantics and models to be shared on the fly. We then discuss potential challenges and opportunities for its development as a flexible, visual, collaborative, scalable and open system.

Collaborative 3D BPMN process modeller

A video detailing our new virtual world BPMN process modelling tool developed by Erik Poppe. Enables better situational awareness via use of remotely connected avatars and a shared 3D process diagram.