An ultra-wide passband (5-30µm) filter for FTIR studies of Photosystem II

This paper reports on the design and manufacture of an ultra-wide (5-30µm) infrared edge filter for use in FTIR studies of the low frequency vibrational modes of metallo-proteins. We present details of the spectral design and manufacture of such a filter which meets the demanding bandwidth and transparency requirements of the application, and spectra that present the new data possible with such a filter. A design model of the filter and the materials used in its construction has been developed capable of accurately predicting spectral performance at both 300K and at the reduced operating temperature at 200K. This design model is based on the optical and semiconductor properties of a multilayer filter containing PbTe (IV-VI) layer material in combination with the dielectric dispersion of ZnSe (II-VI) deposited on a CdTe (II-VI) substrate together with the use of BaF2 (II-VII) as an antireflection layer. Comparisons between the computed spectral performance of the model and spectral measurements from manufactured coatings over a wavelength range of 4-30µm and temperature range 300-200K are presented. Finally we present the results of the FTIR measurements of Photosystem II showing the improvement in signal to noise ratio of the measurement due to using the filter, together with a light induced FTIR difference spectrum of Photosystem II.

Data management for the ocean sciences - perspectives for the next decade

There is remarkable agreement in expectations today for vastly improved ocean data management a decade from now -- capabilities that will help to bring significant benefits to ocean research and to society. Advancing data management to such a degree, however, will require cultural and policy changes that are slow to effect. The technological foundations upon which data management systems are built are certain to continue advancing rapidly in parallel. These considerations argue for adopting attitudes of pragmatism and realism when planning data management strategies. In this paper we adopt those attitudes as we outline opportunities for progress in ocean data management. We begin with a synopsis of expectations for integrated ocean data management a decade from now. We discuss factors that should be considered by those evaluating candidate “standards”. We highlight challenges and opportunities in a number of technical areas, including “Web 2.0” applications, data modeling, data discovery and metadata, real-time operational data, archival of data, biological data management and satellite data management. We discuss the importance of investments in the development of software toolkits to accelerate progress. We conclude the paper by recommending a few specific, short term targets for implementation, that we believe to be both significant and achievable, and calling for action by community leadership to effect these advancements.

Thiolytic screening method for exploring condensed tannin variation in a unique sainfoin germplasm bank

This EU funded 'HealthyHay'project stablished a sainfoin (Onobrychis vicifolia) germplasm bank at NIAB, Cambridge, with 306 accessions from around the world. A screening method was developed to characterise tannins by thiolytic degradation [1] directly in green plants for the first time. the method was validated by separate analysis of unextractable, extractable and purified tannins using thiolysis, HPLC-GPC and MALDI-TOF MS. Most tannins (58 to 73% of the total) could be recovered after Toyopearl HW50 fractionation with water, aqueous methanol and acetone. the greatest losses during purification occurred amongst larger molecular weight tannins with mean degree of polymerisation (mDP) > 18. The composition of water-,aqueous methanol- and acetone-soluble tannins differed considerably in their mDP and trans/cis ratios, but not in their prodelphinidin/orocyanidin (PD/PC) ratios.

Correcting for local oscillator phase offset in a DVB-T compliant receiver under multipath conditions

In 1997, the UK implemented the worlds first commercial digital terrestrial television system. Under the ETS 300 744 standard, the chosen modulation method, COFDM, is assumed to be multipath resilient. Previous work has shown that this is not necessarily the case. It has been shown that the local oscillator required for demodulation from intermediate-frequency to baseband must be very accurate. This paper shows that under multipath conditions, standard methods for obtaining local oscillator phase lock may not be adequate. This paper demonstrates a set of algorithms designed for use with a simple local oscillator circuit which will allow correction for local oscillator phase offset to maintain a low bit error rate with multipath present.

Cloud statistics and cloud radiative effect for a low-mountain site

In 2007, the Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) was operated for a nine-month period in the Murg Valley, Black Forest, Germany, in support of the Convective and Orographically-induced Precipitation Study (COPS). The synergy of AMF and COPS partner instrumentation was exploited to derive a set of high-quality thermodynamic and cloud property profiles with 30 s resolution. In total, clouds were present 72% of the time, with multi-layer mixed phase (28.4%) and single-layer water clouds (11.3%) occurring most frequently. A comparison with the Cloudnet sites Chilbolton and Lindenberg for the same time period revealed that the Murg Valley exhibits lower liquid water paths (LWPs; median = 37.5 g m−2) compared to the two sites located in flat terrain. In order to evaluate the derived thermodynamic and cloud property profiles, a radiative closure study was performed with independent surface radiation measurements. In clear sky, average differences between calculated and observed surface fluxes are less than 2% and 4% for the short wave and long wave part, respectively. In cloudy situations, differences between simulated and observed fluxes, particularly in the short wave part, are much larger, but most of these can be related to broken cloud situations. The daytime cloud radiative effect (CRE), i.e. the difference of cloudy and clear-sky net fluxes, has been analysed for the whole nine-month period. For overcast, single-layer water clouds, sensitivity studies revealed that the CRE uncertainty is likewise determined by uncertainties in liquid water content and effective radius. For low LWP clouds, CRE uncertainty is dominated by LWP uncertainty; therefore refined retrievals, such as using infrared and/or higher microwave frequencies, are needed.

Meteorological phenomena in Western classical orchestral music

Depictions of the weather are common throughout the arts. Unlike in the visual arts, however, there has been little study of meteorological inspiration in music. This article catalogues and analyzes the frequencies with which weather is depicted in a sample of classical orchestral music. The depictions vary from explicit mimicry using traditional and specialized orchestral instruments, through to subtle suggestions. It is found that composers are generally influenced by their own environment in the type of weather they choose to represent. As befits the national stereotype, British composers seem disproportionately keen to depict the UK's variable weather patterns and stormy coastline

Hydrogen-bonding-driven self-assembly of PEGylated organosilica nanoparticles with poly(acrylic acid) in aqueous solutions and in layer-by-layer deposition at solid surfaces

PEGylated organosilica nanoparticles have been synthesized through self-condensation of (3-mercaptopropyl)trimethoxysilane in dimethyl sulfoxide into thiolated nanoparticles with their subsequent reaction with methoxypoly(ethylene glycol) maleimide. The PEGylated nanoparticles showed excellent colloidal stability over a wide range of pH in contrast to the parent thiolated nanoparticles, which have a tendency to aggregate irreversibly under acidic conditions (pH < 3.0). Due to the presence of a poly(ethylene glycol)-based corona, the PEGylated nanoparticles are capable of forming hydrogen-bonded interpolymer complexes with poly(acrylic acid) in aqueous solutions under acidic conditions, resulting in larger aggregates. The use of hydrogen-bonding interactions allows more efficient attachment of the nanoparticles to surfaces. The alternating deposition of PEGylated nanoparticles and poly(acrylic acid) on silicon wafer surfaces in a layer-by-layer fashion leads to multilayered coatings. The self-assembly of PEGylated nanoparticles with poly(acrylic acid) in aqueous solutions and at solid surfaces was compared to the behavior of linear poly(ethylene glycol). The nanoparticle system creates thicker layers than the poly(ethylene glycol), and a thicker layer is obtained on a poly(acrylic acid) surface than on a silica surface, because of the effects of hydrogen bonding. Some implications of these hydrogen-bonding-driven interactions between PEGylated nanoparticles and poly(acrylic acid) for pharmaceutical formulations are discussed.

Structure property relationships in electrically conducting copolymers formed from pyrrole and N-methyl pyrrole

A series of copolymers containing differing proportions of pyrrole and N-methyl pyrrole were prepared electrochemically at various temperatures using acetonitrile as the solvent. The resultant electrical conductivity decreases universally with increasing fraction of N-methyl pyrrole. Films prepared with p-toluene sulfonate as the dopant show a marked variation in structural anisotropy as revealed by X-ray scattering with apparent copolymer content. There is a clear trend between the variation in electrical conductivity and this structural anisotropy. Different patterns of behaviour are observed for films prepared using perchlorate as the dopant and this is attributed to the role of the dopant and final structure in determining the relative reactivities of the pyrrole and N-methyl pyrrole monomers. These observations support the concept that the introduction of methyl substituents into a polypyrrole chain results in a twisted chain conformation. The structure and properties of the resultant copolymer films are particularly sensitive to the preparation conditions.