Effect of post-deposition annealing on transverse piezoelectric coefficient and vibration sensing performance of ZnO thin films

The present experimental study investigates the influence of post-deposition annealing on the transverse piezoelectric coefficient (d(31)) value of ZnO thin films deposited on a flexible metal alloy substrate, and its relationship with the vibration sensing performance. Highly c-axis oriented and crystalline ZnO thin films were deposited on flexible Phynox alloy substrate via radio frequency (RF) reactive magnetron sputtering. ZnO thin film samples were annealed at different temperatures ranging from 100 degrees C to 500 degrees C, resulting in the temperature of 300 degrees C determined as the optimum annealing temperature. The crystallinity, morphology, microstructure, and rms surface roughness of annealed ZnO thin films were systematically investigated by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Atomic Force Microscopy (AFM), respectively. The piezoelectric d(31) coefficient value was measured by 4-point bending method. ZnO thin film annealed at 300 degrees C was highly c-axis oriented, crystalline, possesses fine surface morphology with uniformity in the grain size. This film showed higher d(31) coefficient value of 7.2 pm V-1. A suitable in-house designed and developed experimental set-up, for evaluating the vibration sensing performance of annealed ZnO thin films is discussed. As expected the ZnO thin film annealed at 300 degrees C showed relatively better result for vibration sensing studies. It generates comparatively higher peak output voltage of 147 mV, due to improved structural and morphological properties, and higher piezoelectric d(31) coefficient value. (C) 2014 Elsevier B. V. All rights reserved.

Synthesis and characterization of Ag-Co-Ni nanowires

This work provides an electrodeposition-based methodology for synthesizing multicomponent nanowires containing Ag, Co and Ni atoms. Nanowire morphology was obtained by using an anodic alumina membrane with cylindrical pores of similar to 200-nm diameter. Structural, compositional and magnetic characterization revealed that the as-synthesized nanowires adopted a core-shell microstructure. The core (axial region) contained pure Ag phase volumes with a plate-like morphology oriented perpendicular to the nanowire axis. The shell (peripheral region) contained pure Ag nanoparticles along with superparamagnetic Co and Ni rich clusters.

Agglomeration front dynamics: Drying in sessile nano-particle laden droplets

The drying of sessile, nano-silica laden water droplet is studied under ambient conditions, in the absence of any convection. The drying process can be divided into two distinct regimes. During regime 1, the outer edge of the droplet remains pinned and particles agglomerate at the droplet periphery similar to the traditional coffee ring. However in regime 2, with further evaporation, both the liquid contact line and the agglomeration front starts moving radially inwards from the initial contact edge. The contact between the liquid and the agglomerate is maintained throughout regime 2 and the vaporisation driven liquid edge recession essentially drives the inward growth of the particle deposition. Fast kinetics of particle aggregation results in rapid growth of this agglomeration front as seen from the experiments. A theoretical formulation involving a simplistic model of the agglomeration front growth based on particle mass balance has been proposed. (C) 2014 Elsevier Ltd. All rights reserved,

Markov chains, R-trivial monoids and representation theory

We develop a general theory of Markov chains realizable as random walks on R-trivial monoids. It provides explicit and simple formulas for the eigenvalues of the transition matrix, for multiplicities of the eigenvalues via Mobius inversion along a lattice, a condition for diagonalizability of the transition matrix and some techniques for bounding the mixing time. In addition, we discuss several examples, such as Toom-Tsetlin models, an exchange walk for finite Coxeter groups, as well as examples previously studied by the authors, such as nonabelian sandpile models and the promotion Markov chain on posets. Many of these examples can be viewed as random walks on quotients of free tree monoids, a new class of monoids whose combinatorics we develop.

Combined toxicity of two crystalline phases (anatase and rutile) of Titania nanoparticles towards freshwater microalgae: Chlorella sp

In view of the increasing usage of anatase and rutile crystalline phases of titania NPs in the consumer products, their entry into the aquatic environment may pose a serious risk to the ecosystem. In the present study, the possible toxic impact of anatase and rutile nanoparticles (individually and in binary mixture) was investigated using freshwater microalgae, Chlorella sp. at low exposure concentrations (0.25, 0.5 and 1 mg/L) in freshwater medium under UV irradiation. Reduction of cell viability as well as a reduction in chlorophyll content were observed due to the presence of NPs. An antagonistic effect was noted at certain concentrations of binary mixture such as (0.25, 0.25), (0.25, 0.5), and (0.5, 0.5) mg/L, and an additive effect for the other combinations, (0.25, 1), (0.5, 0.25), (0.5, 1), (1, 0.25), (1, 0.5), and (1, 1) mg/L. The hydrodynamic size analyses in the test medium revealed that rutile NPs were more stable in lake water than the anatase and binary mixtures at 6 h, the sizes of anatase (1 mg/L), rutile NPs (1 mg/L), and binary mixture (1, 1 mg/L) were 948.83 +/- 35.01 nm, 555.74 +/- 19.93 nm, and 1620.24 +/- 237.87 nm, respectively]. The generation of oxidative stress was found to be strongly dependent on the crystallinity of the nanoparticles. The transmission electron microscopic images revealed damages in the nucleus and cell membrane of algal cells due to the interaction of anatase NPs, whereas rutile NPs were found to cause chloroplast and internal organelle damages. Mis-shaped chloroplasts, lack of nucleus, and starch-pyrenoid complex were noted in binary-treated cells. The findings from the current study may facilitate the environmental risk assessment of titania NPs in an aquatic ecosystem. (C) 2015 Elsevier B.V. All rights reserved.

Kinematics and dynamics of Jansen leg mechanism: A bond graph approach

The Jansen mechanism is a one degree-of-freedom, planar, 12-link, leg mechanism that can be used in mobile robotic applications and in gait analysis. This paper presents the kinematics and dynamics of the Jansen leg mechanism. The forward kinematics, accomplished using circle intersection method, determines the trajectories of various points on the mechanism in the chassis (stationary link) reference frame. From the foot point trajectory, the step length is shown to vary linearly while step height varies non-linearly with change in crank radius. A dynamic model for the Jansen leg mechanism is proposed using bond graph approach with modulated multiport transformers. For given ground reaction force pattern and crank angular speed, this model helps determine the motor torque profile as well as the link and joint stresses. The model can therefore be used to rate the actuator torque and in design of the hardware and controller for such a system. The kinematics of the mechanism can also be obtained from this dynamic model. The proposed model is thus a useful tool for analysis and design of systems based on the Jansen leg mechanism. (C) 2015 Elsevier B.V. All rights reserved.

Potential source identification for aerosol concentrations over a site in Northwestern India

The collocated measurements of aerosols size distribution (ASD) and aerosol optical thickness (AOT) are analyzed simultaneously using Grimm aerosol spectrometer and MICROTOP II Sunphotometer over Jaipur, capital of Rajasthan in India. The contrast temperature characteristics during winter and summer seasons of year 2011 are investigated in the present study. The total aerosol number concentration (TANC, 0.3-20 mu m) during winter season was observed higher than in summer time and it was dominated by fine aerosol number concentration (FANC < 2 mu m). Particles smaller than 0.8 mu m (at aerodynamic size) constitute similar to 99% of all particles in winter and similar to 90% of particles in summer season. However, particles greater than 2 mu m contribute similar to 3% and similar to 0.2% in summer and winter seasons respectively. The aerosols optical thickness shows nearly similar AOT values during summer and winter but corresponding low Angstrom Exponent (AE) values during summer than winter, respectively. In this work, Potential Source Contribution Function (PSCF) analysis is applied to identify locations of sources that influenced concentrations of aerosols over study area in two different seasons. PSCF analysis shows that the dust particles from That Desert contribute significantly to the coarse aerosol number concentration (CANC). Higher values of the PSCF in north from Jaipur showed the industrial areas in northern India to be the likely sources of fine particles. The variation in size distribution of aerosols during two seasons is clearly reflected in the log normal size distribution curves. The log normal size distribution curves reveals that the particle size less than 0.8 pm is the key contributor in winter for higher ANC. (C) 2015 Elsevier B.V. All rights reserved.

A comparison of the fine-scale structure of the diurnal cycle of tropical rain and lightning

In this study, the fine-scale structure of the diurnal variability of ground-based lightning is systematically compared with satellite-based rain. At the outset, it is shown that tropical variability of lightning exhibits a prominent diurnal mode, much like rain. A comparison of the geographical distribution of the timing of the diurnal maximum shows that there is very good agreement between the two observables over continental and coastal regions throughout the tropics. Following this global tropical comparison, we focus on two regions, Borneo and equatorial South America, both of which show the interplay between oceanward and landward propagations of the phase of the diurnal maximum. Over Borneo, both rain and lightning clearly show a climatological cycle of ``breathing in'' (afternoon to early morning) and ``breathing out'' (morning to early afternoon). Over the equatorial east coast of South America, landward propagation is noticed in rain and lightning from early afternoon to early morning. Along the Pacific coast of South America, both rain and lightning show oceanward propagation. Though qualitatively consistent, over both regions the propagation is seen to extend further in rainfall. Additionally, given that lightning highlights vigorous convection, the timing of its diurnal maximum often precedes that of rainfall in the convective life cycle. (C) 2015 Elsevier B.V. All rights reserved.

Conversion of plastic waste into CNTs using Ni/Mo/MgO catalystAn optimization approach by mixture experiment

A combustion technique is used to study the synthesis of carbon nano tubes from waste plastic as a precursor and Ni/Mo/MgO as a catalyst. The catalytic activity of three components Ni, Mo, MgO is measured in terms of amount of carbon product obtained. Different proportions of metal ions are optimized using mixture experiment in Design expert software. D-optimal design technique is adopted due to nonsimplex region and presence of constraints in the mixture experiment. The activity of the components is observed to be interdependent and the component Ni is found to be more effective. The catalyst containing Ni0.8Mo0.1MgO0.1 yields more carbon product. The structure of catalyst and CNTs are studied by using SEM, XRD, and Raman spectroscopy. SEM analysis shows the formation of longer CNTs with average diameter of 40-50 nm.

The Flow Theory of Mechanism-Based Strain Gradient Plasticity

The flow theory of mechanism-based strain gradient (MSG) plasticity is established in this paper following the same multiscale, hierarchical framework for the deformation theory of MSG plasticity in order to connect with the Taylor model in dislocation mechanics. We have used the flow theory of MSG plasticity to study micro-indentation hardness experiments. The difference between deformation and flow theories is vanishingly small, and both agree well with experimental hardness data. We have also used the flow theory of MSG plasticity to investigate stress fields around a stationary mode-I crack tip as well as around a steady state, quasi-statically growing crack tip. At a distance to crack tip much larger than dislocation spacings such that continuum plasticity still applies, the stress level around a stationary crack tip in MSG plasticity is significantly higher than that in classical plasticity. The same conclusion is also established for a steady state, quasi-statically growing crack tip, though only the flow theory can be used because of unloading during crack propagation. This significant stress increase due to strain gradient effect provides a means to explain the experimentally observed cleavage fracture in ductile materials [J. Mater. Res. 9 (1994) 1734, Scripta Metall. Mater. 31 (1994) 1037; Interface Sci. 3(1996) 169].

Visualization Summit 2007: Ten research goals for 2010

At the first international Visualization Summit, more than 100 international researchers and practitioners defined and assessed nine original and important research goals in the context of Visualization Science, and proposed methods for achieving these goals by 2010. The synthesis of the whole event is presented in the 10th research goal. This article contributes a building block for systemizing visualization research by proposing mutually elaborated research goals with defined milestones. Such a consensus on where to go together is only one step toward establishing visualization science in the long-term perspective as a discipline with comparable relevance to chemistry, mathematics, language, or history. First, this article introduces the conference setting. Second, it describes the research goals and findings from the nine workshops. Third, a survey among 62 participants about the originality and importance of each research goal is presented and discussed. Finally, the article presents a synthesis of the nine research goals in the form of a 10th research goal, namely Visualizing Future Cities. The article is relevant for visualization researchers, trend scouts, research programme directors who define the topics that get funds. © 2007 Palgr aveMacmillan Ltd. All rights reserved.

A microstructural investigation of deformation in fine SiC particulate- and whisker-reinforced aluminium-matrix composites

Aluminium-based composites, reinforced with low volume fractions of whiskers and small particles, have been formed by a powder route. The materials have been tested in tension, and the microstructures examined using transmission electron microscopy. The whisker composites showed an improvement in flow stress over the particulate composites, and this was linked to an initially enhanced work-hardening rate in the whisker composites. The overall dislocation densities were estimated to be somewhat higher in the whisker composites than the particulate composites, but in the early stages of deformation the distribution was rather different, with deformation in the whisker material being far more localized and inhomogeneous. This factor, together with differences in the internal stress distribution in the materials, is used to explain the difference in mechanical properties.

Diagnóstico agronómico del sistema de producción de frijol (Phaseolus vulgaris L) en tres localidades representativas del municipio de Ticuantepe, Managua, Nicaragua

El presente estudio se desarrolló durante la época de postrera (1996) en la zona de Ticuantepe, Managua, en las localidades de Buenos Aires, El Edén y Cebadilla, con los objetivos de conocer y profundizar en la problemática agronómica y socioeconómica que se presenta en la producción de frijol (Phaseolus vulgaris L) en el área de estudio, y específicamente investigar que factores de producción están limitando el potencial de rendimiento del cultivo. Como criterio principal se consideró el nivel tecnológico de los productores, definiendo tres grupos de tecnología: tecnología alta, tecnología media y tecnología baja. Se tomaron como muestra veinte productores. La información se recolectó a través de encuesta semi-estructurada, abordando los aspectos involucrados en la producción de frijol tanto agronómicos como socioeconómicos, se aplicó una hoja de campo para analizar los componentes del rendimiento, se calculó la producción estimada para realizar análisis de rendimiento y rentabilidad del cultivo al igual que se realizaron consultas con las instituciones de apoyo al agro que se desempeñan en la zona en diversos aspectos. Los resultados del estudio muestran que existe poca asistencia técnica de parte de las instituciones de apoyo a la agricultura y ausencia de planes de apoyo crediticio de cualquier modalidad. En referencia al manejo agronomico el estudio mostro que existen deficiencias especialmente en lo que se refiere a la fertilización, manejo de plagas y enfermedades debido a la falta de conocimientos basicos de los productores en estos aspectos. De igual forma los criterios de fertilización no están bien definidos, por lo que es comun el mal uso de formulas y dosis del fertilizante. Los productores de tecnologia alta presentan buena rentabilidad con un promedio de 359.21 por ciento de acuerdo a los rendimientos estimados y valor de venta del producto. De igual forma los productores de tecnología media obtienen buena rentabilidad con un promedio de 281.4 por ciento, a excepción de un productor que obtuvo rentabilidad negativa (24.90). Los productores de tecnología baja tienen los rendimientos estimados y rentabilidades más bajas con un promedio de 169.64 por ciento, y aún así, de ocho productores solo tres obtienen rentabilidad negativa (25.4, 47.60 y 22.10 por ciento), lo que demuestra que el cultivo de frijol si es un cultivo rentable a pesar de las diferentes problemáticas que presentan los productores, al igual que se perfila como un cultivo que pasa a ser de subsistencia a un cultivo que genera ganancias.