Editorial

The 2nd International Digital Human Modeling (DHM) Symposium was held at the renowned University of Michigan Transportation Research Institute (UMTRI) in Ann Arbor, Michigan in June 11–13, 2013. The symposium was co-organised by the UMTRI and Penn State University, and endorsed by the IEA Technical Committee on Human Simulation and Virtual Environments. The conference built on the very successful inaugural event DHM2011 held in Lyon two years before; and a decade of digital human modelling conferences held under the auspices of SAE International. Practitioners and scientists from 13 countries gathered to present their state-of-the-art developments and applied research, besides discussing the most recent advances in human modelling and directions for future work in DHM...

Correcting flaws in Mitchell’s analysis of EPBC

Efficient error-Propagating Block Chaining (EPBC) is a block cipher mode intended to simultaneously provide both confidentiality and integrity protection for messages. Mitchell’s analysis pointed out a weakness in the EPBC integrity mechanism that can be used in a forgery attack. This paper identifies and corrects a flaw in Mitchell’s analysis of EPBC, and presents other attacks on the EPBC integrity mechanism.

Real-time and interactive attacks on DNP3 critical infrastructure using Scapy

The Distributed Network Protocol v3.0 (DNP3) is one of the most widely used protocols, to control national infrastructure. Widely used interactive packet manipulation tools, such as Scapy, have not yet been augmented to parse and create DNP3 frames (Biondi 2014). In this paper we extend Scapy to include DNP3, thus allowing us to perform attacks on DNP3 in real-time. Our contribution builds on East et al. (2009), who proposed a range of possible attacks on DNP3. We implement several of these attacks to validate our DNP3 extension to Scapy, then executed the attacks on real world equipment. We present our results, showing that many of these theoretical attacks would be unsuccessful in an Ethernet-based network.

Internet-wide scanning taxonomy and framework

Industrial control systems (ICS) have been moving from dedicated communications to switched and routed corporate networks, making it probable that these devices are being exposed to the Internet. Many ICS have been designed with poor or little security features, making them vulnerable to potential attack. Recently, several tools have been developed that can scan the internet, including ZMap, Masscan and Shodan. However, little in-depth analysis has been done to compare these Internet-wide scanning techniques, and few Internet-wide scans have been conducted targeting ICS and protocols. In this paper we present a Taxonomy of Internet-wide scanning with a comparison of three popular network scanning tools, and a framework for conducting Internet-wide scans.

Risk factors for delayed healing in venous leg ulcers : a review of the literature

Background Chronic leg ulcers, remaining unhealed after 4–6 weeks, affect 1-3% of the population, with treatment costly and health service resource intensive. Venous disease contributes to approximately 70% of all chronic leg ulcers and these ulcers are often associated with pain, reduced mobility and a decreased quality of life. Despite evidence-based care, 30% of these ulcers are unlikely to heal within a 24-week period and therefore the recognition and identification of risk factors for delayed healing of venous leg ulcers would be beneficial. Aim To review the available evidence on risk factors for delayed healing of venous leg ulcers. Methods: A review of the literature in regard to risk factors for delayed healing in venous leg ulcers was conducted from January 2000 to December 2013. Evidence was sourced through searches of relevant databases and websites for resources addressing risk factors for delayed healing in venous leg ulcers specifically. Results Twenty-seven studies, of mostly low-level evidence (Level III and IV), identified risk factors associated with delayed healing. Risk factors that were consistently identified included: larger ulcer area, longer ulcer duration, a previous history of ulceration, venous abnormalities and lack of high compression. Additional potential predictors with inconsistent or varying evidence to support their influence on delayed healing of venous leg ulcers included decreased mobility and/or ankle range of movement, poor nutrition and increased age. Discussion Findings from this review indicate that a number of physiological risk factors are asso- ciated with delayed healing in venous leg ulcers and that social and/or psychological risk factors should also be considered and examined further. Conclusion The findings from this review can assist health professionals to identify prognostic indicators or risk factors significantly associated with delayed healing in venous leg ulcers. This will facilitate realistic outcome planning and inform implementation of appropriate early strategies to promote healing.

Crystal structure of the magnesium salt of the herbicide 2,4-D: pentaaqua[(2,4-dichlorophenoxy)acetato-kO]magnesium (2,4-dichlorophenoxy)acetate hemihydrate

In the structure of the title magnesium complex with the phenoxy herbicide (2,4-dichlorophenoxy)acetic acid (2,4-D), [Mg(H2O)5(C8H5Cl2O3)]+ C8H5Cl2O3)- . 0.5H2O, the discrete cationic MgO6 complex units comprise a carboxyl O-donor from a monodentate 2,4-D cationic ligand and five water molecules in a slightly distorted octahedral coordination. The 2,4-D anions are linked to the complex units through duplex water O-H...O(carboxyl) hydrogen bonds through the coordinated water molecules. In the crystal inter-unit O-H...O hydrogen-bonding interactions involving coordinated water molecules as well as the hemi-hydrate solvate molecule with carboxyl O-atom acceptors, give a two-dimensional layered structure lying parallel (001), in which pi-pi ligand-cation interactions [minimum ring centroid separation, 3.6405(17)A] and a short O-H...Cl interaction [3.345(2)A] are also found.

A new constraint handling method for wind farm layout optimization with lands owned by different owners

For wind farm optimizations with lands belonging to different owners, the traditional penalty method is highly dependent on the type of wind farm land division. The application of the traditional method can be cumbersome if the divisions are complex. To overcome this disadvantage, a new method is proposed in this paper for the first time. Unlike the penalty method which requires the addition of penalizing term when evaluating the fitness function, it is achieved through repairing the infeasible solutions before fitness evaluation. To assess the effectiveness of the proposed method on the optimization of wind farm, the optimizing results of different methods are compared for three different types of wind farm division. Different wind scenarios are also incorporated during optimization which includes (i) constant wind speed and wind direction; (ii) various wind speed and wind direction, and; (iii) the more realisticWeibull distribution. Results show that the performance of the new method varies for different land plots in the tested cases. Nevertheless, it is found that optimum or at least close to optimum results can be obtained with sequential land plot study using the new method for all cases. It is concluded that satisfactory results can be achieved using the proposed method. In addition, it has the advantage of flexibility in managing the wind farm design, which not only frees users to define the penalty parameter but without limitations on the wind farm division.

Performance-Based Quality Assurance/Quality Control (QA/QC) Acceptance Procedures for In-Place Soil Testing Phase 3

One of the objectives of this study was to evaluate soil testing equipment based on its capability of measuring in-place stiffness or modulus values. As design criteria transition from empirical to mechanistic-empirical, soil test methods and equipment that measure properties such as stiffness and modulus and how they relate to Florida materials are needed. Requirements for the selected equipment are that they be portable, cost effective, reliable, a ccurate, and repeatable. A second objective is that the selected equipment measures soil properties without the use of nuclear materials.The current device used to measure soil compaction is the nuclear density gauge (NDG). Equipment evaluated in this research included lightweight deflectometers (LWD) from different manufacturers, a dynamic cone penetrometer (DCP), a GeoGauge, a Clegg impact soil tester (CIST), a Briaud compaction device (BCD), and a seismic pavement analyzer (SPA). Evaluations were conducted over ranges of measured densities and moistures.Testing (Phases I and II) was conducted in a test box and test pits. Phase III testing was conducted on materials found on five construction projects located in the Jacksonville, Florida, area. Phase I analyses determined that the GeoGauge had the lowest overall coefficient of variance (COV). In ascending order of COV were the accelerometer-type LWD, the geophone-type LWD, the DCP, the BCD, and the SPA which had the highest overall COV. As a result, the BCD and the SPA were excluded from Phase II testing.In Phase II, measurements obtained from the selected equipment were compared to the modulus values obtained by the static plate load test (PLT), the resilient modulus (MR) from laboratory testing, and the NDG measurements. To minimize soil and moisture content variability, the single spot testing sequence was developed. At each location, test results obtained from the portable equipment under evaluation were compared to the values from adjacent NDG, PLT, and laboratory MR measurements. Correlations were developed through statistical analysis. Target values were developed for various soils for verification on similar soils that were field tested in Phase III. The single spot testing sequence also was employed in Phase III, field testing performed on A-3 and A-2-4 embankments, limerock-stabilized subgrade, limerock base, and graded aggregate base found on Florida Department of Transportation construction projects. The Phase II and Phase III results provided potential trend information for future research—specifically, data collection for in-depth statistical analysis for correlations with the laboratory MR for specific soil types under specific moisture conditions. With the collection of enough data, stronger relationships could be expected between measurements from the portable equipment and the MR values. Based on the statistical analyses and the experience gained from extensive use of the equipment, the combination of the DCP and the LWD was selected for in-place soil testing for compaction control acceptance. Test methods and developmental specifications were written for the DCP and the LWD. The developmental specifications include target values for the compaction control of embankment, subgrade, and base materials.

Quantification of functional hand grip using electromyography and inertial sensor-derived accelerations: Clinical implications

Background Assessing hand injury is of great interest given the level of involvement of the hand with the environment. Knowing different assessment systems and their limitations generates new perspectives. The integration of digital systems (accelerometry and electromyography) as a tool to supplement functional assessment allows the clinician to know more about the motor component and its relation to movement. Therefore, the purpose of this study was the kinematic and electromyography analysis during functional hand movements. Method Ten subjects carried out six functional movements (terminal pinch, termino-lateral pinch, tripod pinch, power grip, extension grip and ball grip). Muscle activity (hand and forearm) was measured in real time using electromyograms, acquired with the Mega ME 6000, whilst acceleration was measured using the AcceleGlove. Results Electrical activity and acceleration variables were recorded simultaneously during the carrying out of the functional movements. The acceleration outcome variables were the modular vectors of each finger of the hand and the palm. In the electromyography, the main variables were normalized by the mean and by the maximum muscle activity of the thenar region, hypothenar, first interosseous dorsal, wrist flexors, carpal flexors and wrist extensors. Conclusions Knowing muscle behavior allows the clinician to take a more direct approach in the treatment. Based on the results, the tripod grip shows greater kinetic activity and the middle finger is the most relevant in this regard. Ball grip involves most muscle activity, with the thenar region playing a fundamental role in hand activity. Clinical relevance Relating muscle activation, movements, individual load and displacement offers the possibility to proceed with rehabilitation by individual component.

Designing and evaluating a persuasive child restraint television commercial

Objective Relatively high rates of child restraint inappropriate use, misuse and faults in the installation of restraints have suggested a crucial need for public education messages to raise parental awareness of the need to use restraints correctly. This project involved the devising and pilot testing of message concepts, filming of a television advertisement (the TVC), and the evaluation of the TVC. This paper focuses specifically upon the evaluation of the TVC. The development and evaluation of the TVC were guided by an extended Theory of Planned Behaviour which comprised the standard constructs of attitude, subjective norm, and perceived behavioural control as well as the additional constructs of group norm and descriptive norm. The study also explored the extent to which parents with low and high intentions to self-check restraint/s differed on salient beliefs regarding the behaviour. Methods An online survey of parents (N = 384) was conducted where parents were randomly assigned to either an Intervention group (n = 161), and therefore viewed the advertisement within the survey, or the Control group (n = 223) and therefore did not view the advertisement. Results Following a one-off exposure to the TVC, the results indicated that, although not a significant difference, parents in the Intervention group reported stronger intentions (M = 4.43, SD = .74) to self-check restraints than parents in the Control group (M = 4.18, SD = .86). Also, parents in the Intervention group (M = 4.59, SD = .47) reported significantly higher levels of perceived behavioural control than parents in the Control group (M = 4.40, SD = .73). The regression results revealed that, for parents in the Intervention group, attitude and group norm were significant predictors of parental intentions to self-check their child restraint. Finally, the exploratory analyses of parental beliefs suggested that those parents with low intentions to self-check child restraints were significantly more likely than high intenders to agree that they did not have enough time to check restraints or that having a child in a restraint is more important than checking the installation of the restraint. Conclusion Overall, the findings provide some support for the persuasiveness of the child restraint TVC and provide insight into the factors influencing reported parental intentions as well as salient beliefs underpinning self-checking of restraints. Interventions that attempt to increase parental perceptions of the importance of self-checking restraints regularly and brevity of the time involved in doing so may be effective.

The role of context and motivation variables in mobile commerce usage: A further perspective on Chong (2013)

We comment on a recent article by Chong (2013) on the roles of demographic and motivation variables in mobile commerce usage. Drawing on the recent research on the service-dominant logic, socioemotional selectivity theory, and data from a first empirical study, we argue that a broader discussion on the value relevance of mobile commerce activities for customers and the consideration of consumers' future time perspectives would provide a richer, potentially more appropriate picture of the drivers of mobile commerce usage. Furthermore, using data from a second empirical study, we highlight several validity issues of the used scales. We hope to motivate a replication and extension of Chong's study and also provide recommendations for future research on this area.

Environmental efficiency of energy, materials, and emissions

This study estimates the environmental efficiency of international listed firms in 10 worldwide sectors from 2007 to 2013 by applying an order-m method, a non-parametric approach based on free disposal hull with subsampling bootstrapping. Using a conventional output of gross profit and two conventional inputs of labor and capital, this study examines the order-m environmental efficiency accounting for the presence of each of 10 undesirable inputs/outputs and measures the shadow prices of each undesirable input and output. The results show that there is greater potential for the reduction of undesirable inputs rather than bad outputs. On average, total energy, electricity, or water usage has the potential to be reduced by 50%. The median shadow prices of undesirable inputs, however, are much higher than the surveyed representative market prices. Approximately 10% of the firms in the sample appear to be potential sellers or production reducers in terms of undesirable inputs/outputs, which implies that the price of each item at the current level has little impact on most of the firms. Moreover, this study shows that the environmental, social, and governance activities of a firm do not considerably affect environmental efficiency.