80keV N离子注入对ZnO薄膜结构的影响；Effects of 80 keV N-ion Implantation on Structures of ZnO Films

室温下用80keVN离子注入ZnO薄膜样品,注量分别为5.01014,5.01015和5.01016ions/cm2,然后用X射线衍射和透射电镜技术对样品的结构特性进行了表征。实验结果表明,由高度(002)择优取向的致密柱状晶构成的薄膜中,注入5.0×1015ions/cm2时,观测到缺陷生成和局域无序化现象,但薄膜总体结构仍保持柱状晶和(002)择优取向;随着注量的增大,晶格常数c和压应力呈增大趋势。对注入N离子对ZnO薄膜结构特性的影响机理进行了简单的讨论。

3,5-二甲基吡唑对尿素氮转化及NO_3~--N淋溶的影响

采用室内培养和田间试验相结合的方法,探讨了新型硝化抑制剂3,5-二甲基吡唑(DMP)对尿素氮转化及玉米田硝酸盐淋溶损失的影响.结果表明,DMP对尿素水解仅起短暂的抑制作用,但可在较长时间内显著抑制土壤铵的氧化,且随DMP用量的增加,抑制效应显著增强.培养第10 d时,DMP各处理(0.002 5、0.01及0.025 g/kg)的土壤NH4+-N累积量分别比CK提高了5.17、9.36和11.04倍,而NO3--N累积量于培养第14 d时差异最大,与CK相比分别降低了33.30%、61.19%和73.72%(p<0.01).土壤NO2--N只在尿素施用前期有少量累积,但第3 d DMP各处理土壤NO2--N含量降低幅度达95.77%~96.13%;土壤矿质氮总量于10 d以后,随DMP用量的增加,显著降低,而DMP1处理的土壤微生物量N在培养14~56 d期间显著提高.连续2 a的玉米田间试验原位取土测定结果表明,2004和2005年,DMP的施用使作物根系密集层以下(40~100 cm)土层的NO3--N累积总量分别比CK降低了28.77%和44.70%.因此,硝化抑制剂DMP与尿素配合施用是调控氮素转化、缓解氮肥污染的有效措施.

Heat capacities and thermodynamic properties of chrysanthemic acid

The heat capacities of chrysanthemic acid in the temperature range from 80 to 400 K were measured with a precise automatic adiabatic calorimeter. The chrysanthemic acid sample was prepared with the purity of 0.9855 mole fraction. A solid-liquid fusion phase transition was observed in the experimental temperature range. The melting point, T-m, enthalpy and entropy of fusion, Delta(fus)H(m), Delta(fus)S(m), were determined to be 390.741 +/- 0.002 K, 14.51 +/- 0.13 kJ mol(-1), 37.13 +/- 0.34 J mol(-1) K-1, respectively. The thermodynamic functions of chrysanthemic acid, H-(T)-H-(298.15), S-(T)-S-(298.15) and G((T))-G((298.15)) were reported with a temperature interval of 5 K. The TG analysis under the heating rate of 10 K min(-1) confirmed that the thermal decomposition of the sample starts at ca. 410 K and terminates at ca. 471 K. The maximum decomposition rate was obtained at 466 K. The purity of the sample was determined by a fractional melting method.

科尔沁沙地沙丘演替过程的土壤种子库特征

该文研究了科尔沁沙地沙丘演替阶段(流动沙丘-半流动沙丘-半固定沙丘-固定沙丘)的土壤种子库特征.土壤种子库物种组成和种子密度均以一年生植物为主.流动和半流动沙丘土壤种子库密度约为90和364粒/m2,半固定和固定沙丘种子密度显著增加到723和8 880粒/m2.沙丘演替阶段种子密度的时间动态和土壤种子垂直分布特征分析结果表明:流动半流动沙丘无显著差异(P>0.05),固定半固定沙丘则有显著差异(P≤0.002);固定半固定沙丘的植物种子表现为持久土壤种子库类型Ⅲa,并且随土壤深度增加,土壤种子密度显著下降.沙丘演替阶段土壤种子库的种子密度与植物在地上植被中出现的频度具有显著相关性,二者相关系数为0.568.

黄土高原典型土壤剖面土壤颗粒组成分形特征

采集从北向南依次分布的干润砂质新成土(神木)、黄土正常新成土(延安)和土垫旱耕人为土(杨陵)等典型土壤剖面0～200cm土层土样,通过测定土样颗粒体积分形维数及基本性质,以期阐明黄土高原典型土壤颗粒体积分形特征及其与土壤基本性质间的相关性。结果表明,从南到北,土壤颗粒体积分形维数呈下降趋势,而不同土层土壤颗粒体积分形维数差异不显著。土垫旱耕人为土、黄土正常新成土和干润砂质新成土表层(0～10cm)颗粒体积分形维数分别为2.723±0.024、2.609±0.077和2.589±0.025,表层以下(10～200cm)颗粒平均体积分形维数分别为2.729±0.034、2.584±0.054和2.558±0.034;颗粒体积分形维数与<0.01mm的物理性黏粒及<0.002mm的黏粒体积百分含量呈极显著正相关关系,与0.002～0.05mm的粉粒和>0.05mm的砂粒体积百分含量呈极显著负相关关系,与粉粒的显著性较小,而土壤中物理性黏粒体积百分含量与土壤全氮、有机碳及矿物固定态铵均达到极显著正相关关系,而砂粒体积百分含量与上述土壤基本性质均呈极显著负相关关系。

下辽河平原潮棕壤不同粒级碳和氮分布研究

采用具有不同开垦年限的0~20和20~40 cm耕层土壤,对其不同粒级的有机碳和全N分布进行了研究.结果表明,在0~20和20~40 cm耕层,<0.002 mm粒级的有机碳含量最高,<0.02 mm粒级含量次之,<0.2 mm粒级含量最少.土壤全N的粒级分布规律与有机碳基本相同.在同一粒级中,有机碳和全N的各粒级分布与开垦年限没有明显的相关性.各粒级的有机碳与全N相关性极显著,在<0.2 mm粒级的相关系数为0.74,在<0.02 mm和<0.002 mm分别达到了0.94和0.91.

Strings of interconnected hollow carbon nanoparticles with porous shells prepared using simple solid-phase synthesis

Strings of interconnected hollow carbon nanoparticles with porous shells were prepared by simple heat-treatments of a mixture of resorcinol-formaldehyde gel and transition-metal salts. The sample was characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction and nitrogen adsorption. Results show that the sample consisted of relatively uniform hollow particles with sizes ranging from 70 to 80 nm forming a strings-of-pearls-like nanostructure. The material with porous shells possessed well-developed graphitic structure with an interlayer (d(002)) spacing of 0.3369 nm and the stack height of the graphite crystallites of 9 nm.

First principles investigation on the structural, mechanical and electronic properties of OsC2

The structural, mechanical and electronic properties Of OsC2 were investigated by use of the density functional theory. Seven structures were considered, i.e., orthorhombic Cmca (No. 12, OsSi2), Pmmn (No. 59, 002) and Pnnm (No. 58, OsN2); tetragonal P4(2)/mnm (No. 136, OsO2) and 14/mmm (No. 139, CaC2); cubic Fm-3m (No. 225, CaF2) and Pa-3 (No. 205, PtN2). The results indicate that Cmca in OsSi2 type structure is energetically the most stable phase among the considered structures. It is also stable mechanically. OsC2 in Pmmn phase has the largest bulk modulus 319 GPa and shear modulus 194 GPa. The elastic anisotropy is discussed. (C) 2009 Elsevier B.V. All rights reserved.

Synthesis, photoluminescence, thermoluminescence and dosimetry properties of novel phosphor KSr4(BO3)(3):Ce

Polycrystalline powder sample of KSr4(BO3)(3) was synthesized by high-temperature solid-state reaction. The influence of different rare earth dopants, i.e. Tb3+, TM3+ and Ce3+, on thermoluminescence (TL) of KSr4(BO3)(3) Phosphor was discussed. The TL, photoluminescence (PL) and some dosimetric properties of Ce3+-activated KSr4(BO3)(3) phosphor were studied. The effect of the concentration of Ce3+ on TL intensity was investigated and the result showed that the optimum Ce3+ concentration was 0.2 mol%. The TL kinetic parameters of KSr4(BO3)(3):0.002 Ce3+ phosphor were calculated by computer glow curve deconvolution (CGCD) method. Characteristic emission peaking at about 407 and 383 nm due to the 4f(0)5d(1) -> F-2((5/2),(7/2)) transitions of Ce3+ ion were observed both in PL and three-dimensional (3D) TL spectra. The dose-response of KSr4(BO3)(3):0.002 Ce3+ to gamma-ray was linear in the range from 1 to 1000 mGy. In addition, the decay of the TL intensity of KSr4(BO3)(3):0.002 Ce3+ was also investigated.

基于二次开发平台的阳极溶出伏安仪

建立了一种适合研发电化学仪器的新型二次开发平台,开发了一系列仪器模块和组件,并利用此平台研制了一种操作方便、成本低廉的微型半自动阳极溶出伏安仪(MASV)。仪器采用了20位数模转换器和16位模数转换器,电流测量范围为1 pA～20 mA;支持线形扫描法和微分脉冲伏安法等电化学方法。电解池可原位清洗,搅拌均匀高效且速度可调;仪器体积小,且不需要外接电源,操作方便。利用MASV进行了一系列阳极溶出实验,获得了Cd2+和Pb2+溶液的标准曲线,其相关系数均大于0.999,检出限可达μg/L数量级,重现性较好。测试了环境水样中的Cd2+和Pb2+的含量。

Preparation and electrical properties of new oxide ion conductors Ce6-xDyxMoO15-delta (0.0 <= x <= 1.8)

Ce6-xDyxMoO15-delta (0.0 <= x <= 1.8) were synthesized by modified sol-gel method. Structural and electrical properties were investigated by means of X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The XRD patterns showed that the materials were single phase with a cubic fluorite structure. Impedance spectroscopy measurement in the temperature range between 350 degrees C and 800 degrees C indicated a sharp increase in conductivity for the system containing small amount of Dy2O3. The Ce5.6Dy0.4MoO15-delta detected to be the best conducting phase with the highest conductivity (sigma(t) = 8.93 x 10(-3) S cm(-1)) is higher than that of Ce5.6Sm0.4MoO15-delta (sigma(t) = 2.93 x 10(-3) S cm(-1)) at 800 degrees C, and the corresponding activation energy of Ce5.6Dy0.4MoO15-delta (0.994 eV) is lower than that of Ce5.6Sm0.4MoO15-delta (1.002 eV).

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

Capillary electrophoresis with solid-state electrochemiluminescence detector

We report capillary electrophoresis coupling to a solid-state electrochemiluminescence (ECL) detector for the first time. The solid-state ECL detector was fabricated by immobilizing the ECL reagent tris(2,2'-bipyridyf)ruthenium (TBR) in poly-(p-styrenesulfonate)-silica-poly(vinyl alcohol) grafting 4-vinylpyridine copolymer films. The excellent stability of the solid-state ECL detector in the phosphate solution satisfied application in CE. The CE with solid-state ECL detector system was characterized using tripropylamine (TPA) and proline. The influences of detection potential, the concentration of TBR in the film, and pH value of ECL buffer were investigated. The linear range for TPA and proline was 0.005-10 muM and 5-10 mM with correlation coefficients of 0.997 and 0.998, respectively. The detection limit (signal-to-noise ratio S/N = 3) was estimated to be 0.002 and 2.0 muM for TPA and proline, respectively. The relative standard deviations for 1.0 pm TPA and 1.0 mm proline were 8.7% and 7.5% with theoretical plate numbers of 70 000 and 16 000, respectively. Compared with the CE-ECL of TBR in aqueous solution, the CE coupling with solid-state ECL detector system gave the same sensitivity of analysis.

Lamellar single crystals of nylon-10,10 crown from a dimethylformamide solution

A new solvent, dimethylformamide (DMF), and the traditional solvent, 1,4-butanediol, were used to prepare single crystals of nylon-10,10 from a dilute solution. The lamellae grown from DMF inhabited a more perfect structure and regular shape than those crystals crystallized from traditional solvents such as 1,4-butanediol and glycerin. These thin and perfect lamellar crystals demonstrated patterns of variation in spacing different from those of melt-crystallized spherulites on heating. Specifically, the two main spacings slightly separated rather than continuously approaching each other when the temperature was greater than 180 degreesC. This is a novel phenomenon observed in nylons. Nevertheless, the usual pattern of change in spacing was observed during the cooling process. These lamellar crystals showed more compact spacing of the (002) and (010/100) planes than spherulites at room temperature. (C) 2001 John Wiley & Sons, Inc.

Crystal structure and mechanism of (Z)-1-[2-(phenyl-bromide-chloride)vinyl]-1-cyclohexanol

The crystal structure and mechanism of the title molecule are described. This crystal is orthorhombic, belonging to space group PC21/B with a=1,002 1(2) nm, b=1.483 0(3) nm, c=2.173 6(4) nm, V=3.230 39(2) nm(3), Z=2, D-c=1.80 g/cm(3), R=0.069 3. The structure was solved by direct method. The tin atom of the title compound exists in two distorted-trigonal-bipyramidal geometry, defined by two carbon, one bromide, one chloride and one oxygen atoms leading to a five-membered chelate ring. In the structure, the five-membered ring containing the intermolecular O-->Sn has a half chair conformation.