Synthesis and sintering of PZT ceramics

Lead zirconate powder, with Zr/Ti ratio of 50/50 was prepared by polymeric precursor method and doped with 3, 5 and 7 mol% of Sr+2 Or Ba+2, as well as by 0.2 to 5 mol% of Nb+5. The powder was calcined at 750 degrees C by 4 hours and milled during 1.5 h in isopropilic alcohol. Powders were characterized by surface area measurements (BET method), by infrared spectroscopy and by X-ray diffraction to characterize the crystal structure. Isostatically pressed samples were sintered in a dilatometer furnace by using a constant heating rate of 10 degrees C/min from ambient to 1200 degrees C. Synthetic air and air with water vapor were used as atmospheres. Both Sr+2 and Ba+2 substitute Pb+2 and favor the formation of rhombohedral phase. Otherwise, Nb+5 substitute preferentially Zr+4 favoring tetragonal phase. The concentration of dopants and the atmosphere influence the densification and the microstructure of the PZT, which alters the dielectric and piezoelectric properties of the ceramics.

Hollow silica particles from microemulsion

Silica particles were obtained by addition of diluted soluble sodium silicate in sodium 1,2 bis (2-ethylhexyloxycarbonyl)-1-ethenesulfonate reverse microemulsions, in which aqueous phase was nitric acid solution and the water/surfactant ratio (W) was 5 or 10. Products, whether washed or not, were dried at 100 degrees C and suspended in different solvents: heptane, water, kerosene or pentane for making SEM measurements. Thermal treatments of washed silica samples were carried out at 900 degrees C and 1200 degrees C. Silica particles of sizes from 1 to 10 mu m were obtained at room temperature without changing their shape due to thermal treatment and crystallization. SEM micrographs show hollow particles suggesting that silica preferably polymerizes on microemulsion droplet interface where ionic strength of nitric acid aqueous solution is favourable for silica polymerization reaction. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Simultaneous determination of Al, As, Cu, Fe, Mn, and Ni in fuel ethanol by GFAAS

A method has been developed for the simultaneous determination of Al, As, Cu, Fe, Mn, and Ni in fuel ethanol by graphite furnace atomic absorption spectrometry (GFAAS) using a transversely heated graphite atomizer (THGA) with longitudinal Zeeman-effect background correction. The thermal behavior of analytes during the pyrolysis and atomization stages using the mixture Pd(NO3)(2) + Mg(NO3)(2) as the chemical modifier was investigated in 0.028 mol L-1 HNO3, 0.14 mol L-1 HNO3, and diluted ethanol (1 + 1, v/v) containing different nitric acid concentrations. With 5 rhog Pd + 3 mug Mg as the modifiers, pyrolysis and atomization temperatures of the heating program of the atomizer were fixed at 1200 C and 2200degreesC respectively. For 20 muL of diluted sample (10 muL ethanol + 10 muL of 0.28 mol L-1 HNO3) dispensed into the graphite tube, analytical curves in the 2.0 - 50 mug L-1 Al, As, Cu, Fe, Mn, Ni ranges were established. The calculated characteristic masses were - 37 pg Al, 73 pg As, 31 pg Cu, 16 pg Fe, 9 pg Mn, and 44 pg Ni, and the lifetime of the tube was around 2 50 firings. The limits of detection (LOD) based on integrated absorbance were 1.2 mug L-1 Al, 2.5 mug L-1 As. 0.22 mug L-1 Cu, 1.6 L-1 Fe 0.20 mug L-1 Mn 1.1 mug L-1 Ni. The relatively standard deviations (n = 12) were less than or equal to 3%, less than or equal to 6%, less than or equal to 2%, less than or equal to 3.4%, less than or equal to 1.3%, and less than or equal to 2% for Al, As, Cu, Fe, Mn, and Ni, respectively, the recoveries of Al, As, Cu, Fe, Mn and Ni added to fuel ethanol samples varied from 77% to 112%, 92% to 114%, 104% to 113%, 73% to 116%, 91% to 122% and 93% to 116%, respectively. Accuracy was checked for Al, As, Cu, Fe, Mn, and Ni determination in 20 samples purchased at local gas stations in Araraquara city, Brazil. A paired t-test showed that the results were in agreement at the 95% confidence level with those obtained by single-element GFAAS.

Physiological responses of Nile tilapia, Oreochromis niloticus, fed vitamin C- and lipid-supplemented diets and submitted to low-temperature stress

Water temperature alterations can determine harmful physiological modifications in fish, which should be prepared to cope with this, and nutrition strategies seem to be essential. This study evaluated the effects of different levels of vitamin C and lipids on physiological responses of Nile tilapia, Oreochromis niloticus, submitted to temperature stress. There were two phases: Phase I - preparing fish to store vitamin C and lipid at appropriate temperature, and Phase II - evaluating the contributions these reserves make to fish physiology under low-temperature stress. The experiment used a 3 x 2 factorial design with three vitamin C levels (300, 600, and 1200 mg/kg diet) and two lipid levels (8.0 and 12.0%), plus absence of nutrient test and a diet of 6.0% lipids and 125.0 mg/kg vitamin C. In Phase I, 192 fish were kept at 26.0 +/- 1.0 C for 112 d, and in Phase II, 48 fish were kept at 18.0 +/- 0.5 C for 32 d and at 15.0 +/- 0.5 C for 11 d. Fish fed C0L0 diet showed lower erythrocytes values in both phases; higher vitamin C supplement determined higher red blood cell (RBC) number and higher hematocrit (Htc) (Phase II); Htc was significantly lower in Phase II; after temperature stress, fish fed C0L0 diet had higher mean corpuscular volume, lower hemoglobin corpuscular concentration, and significantly lower vitamin C concentration in the liver; and higher supplementation determined a higher concentration in the liver (Phases I and II). Higher plasmatic cortisol concentration was seen in fish fed C0L0 diet. In conclusion, our results show that the absence of vitamin C in diets impairs RBC formation and does not enable fish to cope with stress; excess vitamin C is efficient in mitigating stress and 600 mg/kg diet is economic and physiologically sufficient to prepare fish for coping with low-temperature stress. Lipid supplementation does not determine alterations in stress biochemical parameters.

Anxiolytic effect of estradiol in the median raphe nucleus mediated by 5-HT1A receptors

Estrogen deficiency has been associated with stress, anxiety and depression. Estrogen receptors have been identified in the median raphe nucleus (MRN). This structure is the main source of serotonergic projections to the hippocampus, a forebrain area implicated in the regulation of defensive responses and in the resistance to chronic stress. There is evidence showing that estrogen modulates 5-HT1A receptor functions. In the MRN, somatodendritic 5-HT1A receptors control the activity of serotonergic neurones by negative feedback. The present study evaluated the effect of intra-MRN injection of estradiol benzoate (EB) (600 or 1200 ng/0.2 mu l) on the performance of ovariectomised rats submitted to the elevated plus-maze test of anxiety and to the open-field test. Additionally, the same effect was evaluated with a previous intra-MRN injection of WAY 100635 (100 ng/0.2 mu l), an antagonist of 5-HT1A receptors. The results showed that both doses of EB increased the percentage of entries and the percentage of time spent into the open arms, suggestive of an anxiolytic effect. The highest dose of the drug also increased the number of entries into the enclosed arm and locomotion in the open field, indicating a stimulatory motor effect. WAY 100635 antagonised the effect of estradiol in the elevated plus-maze and in the open-field. The results show that estrogen receptors of the MRN are implicated in the regulation of anxiety-related behaviour. The results also support claims that the effect of estrogen involves a change in 5-HT1A receptor function. (C) 2005 Elsevier B.V. All rights reserved.

Synthesis and photoluminescence study of La1.8Eu0.2O3 coating on nanometric alpha-Al2O3

In this work the La1.8Eu0.2O3 coating on nanometric alpha-alumina, alpha-Al2O3@La1.8Eu0.2O3, was prepared for the first time by a soft chemical method. The powder was heat-treated at 100, 400, 800 and 1200 degrees C for 2 h. X-ray powder diffraction patterns (XRD), transmission electronic microscopy (TEM), emission and excitation spectra, as well as Eu3+, lifetime were used to characterize the material and to follow the changes in structure as the heating temperature increases. The Eu3+ luminescence data revealed the characteristic transitions D-5(0) --> F-7(J) (J = 0, 1 and 3) of Eu3+ at around 580, 591 and 613 nm, respectively, when the powders were excited by 393 nm. The red color of the samples changed to yellow when the powder was annealed at 1200 degrees C. The decrease in the (D-5(0) --> F-7(2))/(D-5(0) --> F-7(1)) ratio from around 5.0 for samples heated at lower temperatures to 3.1 for samples annealed at 1200 degrees C is consistent with a higher symmetry of the Eu3+ at higher temperature. The excitation spectra of the samples also confirms this change by the presence of a more intense and broad band at around 317 nm, instead of the presence of the characteristic peak at 393 mn, which corresponds to the F-7(0) --> L-5(6) transition of the Eu3+. The lifetimes of the D-5(0) --> F-7(2) transition of Eu3+ for the samples heat-treated at 100, 400, 800 and 1200 degrees C was evaluated as 0.57, 0.72, 0.43 and 0.31 ms, respectively. (C) 2006 Elsevier Ltd. All fights reserved.

Efeito do período de jejum na fase final de crição de frangos de corte machos sobre rendimento e composição da carcaça

The objective of this work was to evaluate the effect of fasting period in the last growing phase on carcass yield and composition of male broilers. Two thousand one-day old male chicks were distributed in five randomized blocks according to a 4x2 factorial (four feeding programs (P): ad libitum or one of three fasting schedules: 8-12, 12-16 and 8-16; and two strains (S): Ross or Hubbard-Peterson, Fifty birds were used per replicate. Birds were raised under identical feed and management conditions until day 42. The fasting schedules were applied from day 43 to day 56. At day 56, five birds per replicate were randomly sampled, weighed, slaughtered, eviscerated, dry-cooled, cut and deboned. No effects of P or SxP interaction were observed for carcass characteristics. birds, which showed higher weights and yields of head plus neck, feet, leg bones and wings. The ad libitum birds showed higher crude protein in thigh meat than those submitted to the 8-12 h fast. A SxP interaction was observed for meat ash content. The R broilers showed higher ash content in breast and thigh meat than the H birds in the 8-12 h fast treatment. on the other hand, the R broilers submitted to the 8-12 h fast showed higher ash contents in breast and thigh meat than birds from the same strain in the other feeding programs. Fasting in the last phase of rearing did not alter the yield of whole carcass, carcass cuts and abdominal fat, but morning fast influenced carcass chemical composition.

Maximum number of flux lines inside columnar defects

We set new limits for the maximum number of fluxons trapped inside columnar defects, for both cases of metallic and insulated cores. We show that the saturation limit predicted by the Mkrtchyan and Shmidt theory is just a first approximation to our results, because it does not consider the presence of the remaining flux lines exterior to the defects.

Densification and electrical conductivity of fast fired manganese-doped ceria ceramics

Reactive pure and manganese-doped (5% and 10 at.%) ceria nanosized powders were prepared by the polymeric precursor technique. Physical properties of powder materials were studied by X-ray diffraction, nitrogen adsorption, and diffuse reflectance infrared Fourier transform spectroscopy. Characterization of powder compacts after fast firing at 1200 degrees C for 5 min was carried out by scanning electron microscopy and impedance spectroscopy measurements. The bulk apparent density of sintered pellets was determined for pellets of different compositions sintered at 1200 degrees C. A gradual decrease of the particle size occurs with increasing doping content. Relatively high values of apparent density were obtained after fast firing doped specimens at 1200 degrees C. DRIFT spectra evidence that a fraction of Mn ions was segregated onto particles surface. The electrical resistivity of sintered pellets reveals different mechanisms of conduction depending on the Mn content. (C) 2005 Elsevier B.V All rights reserved.

Synthesis and characterization of 9.5/65/35 PLZT prepared from the polymeric precursors

The 9.5/65/35 PLZT was prepared from the polymeric precursors (the Pechini and partial oxalate process) and by sintering in two stages in an oxygen atmosphere. After thermal treatment at 400 degreesC, the powders were calcinated and sintered at 1200 degreesC with slow heating and cooling rates. The second stage of sintering consisted of hot pressing at the same temperature in oxygen atmosphere. After calcination of PLZT powders obtained by both methods, as well as after sintering of PLZT obtained by Pechini process, the paraelectric cubic phase was formed. After sintering of PLZT obtained by partial oxalate procedure, small tetragonality of crystal structure was observed. After hot pressing PLZT was pseudocubic. SEM microstructural analyses were carried out of the sintering and hot pressed samples and indicated the small grain size less than 2 mum. (C) 2001 Elsevier B.V. B.V. All rights reserved.

The Serido Group of NE Brazil, a late Neoproterozoic pre- to syn-collisional basin in West Gondwana: insights from SHRIMP U-Pb detrital zircon ages and Sm-Nd crustal residence (T-DM) ages

The Serido Group is a deformed and metamorphosed metasedimentary sequence that overlies early Paleoproterozoic to Archean basement of the Rio Grande do Norte domain in the Borborema Province of NE Brazil. The age of the Serido Group has been disputed over the past two decades, with preferred sedimentation ages being either Paleoproterozoic or Neoproterozoic. Most samples of the Serido Formation, the upper part of the Serido Group, have Sm-Nd T-DM ages between 1200 and 1600 Ma. Most samples of the Jucurutu Formation, the lower part of the Serido Group, have T-DM ages ranging from 1500 to 1600 Ma; some basal units have T-DM ages as old as 2600 Ma, reflecting proximal basement. Thus, based on Sm-Nd data, most, if not all, of the Serido Group was deposited after 1600 Ma and upper parts must be younger than 1200 Ma.Cathodoluminescence photos of detrital zircons show very small to no overgrowths produced during ca. 600 Ma Brasiliano deformation and metamorphism, so that SHRIMP and isotope dilution U-Pb ages must represent crystallization ages of the detrital zircons. Zircons from meta-arkose near the base of the Jucurutu Formation yield two groups of ages: ca. 2200 Ma and ca. 1800 Ma. In contrast, zircons from a metasedimentary gneiss higher in the Jucurutu Formation yield much younger ages, with clusters at ca. 1000 Ma and ca. 650 Ma. Zircons from metasedimentary and metatuffaceous units in the Serido Formation also yield ages primarily between 1000 and 650 Ma, with clusters at 950-1000, 800, 750, and 650 Ma. Thus, most, if not all, of the Serido Group must be younger than 650 Ma. Because these units were deformed and metamorphosed in the ca. 600 Ma Brasiliano fold belt during assembly of West Gondwana, deposition probably occurred ca. 610-650 Ma, soon after crystallization of the youngest population of zircons and before or during the onset of Brasiliano deformation.The Serido Group was deposited upon Paleoproterozoic basement in a basin receiving detritus from a variety of sources. The Jucurutu Formation includes some basal volcanic rocks and initially received detritus from proximal 2.2-2.0 Ga (Transamazonian) to late Paleoproterozoic (1.8-1.7 Ga) basement. Provenance for the upper Jucurutu Formation and all of the Serido Formation was dominated by more distal and younger sources ranging in age from 1000 to 650 Ma. We suggest that the Serido basin may have developed as the result of late Neoproterozoic extension of a pre-existing continental basement, with formation of small marine basins that were largely floored by cratonic basement (subjacent oceanic crust has not yet been found). Immature sediment was initially derived from surrounding land; as the basin evolved much of the detritus probably came from highlands to the south (present coordinates). Alternatively, if the Patos shear zone is a major terrane boundary, the basin may have formed as an early collisional foredeep associated with south-dipping subduction. In any case, within 30 million years the region was compressed, deformed, and metamorphosed during final assembly of West Gondwana and formation of the Brasiliano-Pan African fold belts. (C) 2003 Elsevier B.V. All rights reserved.

TG studies of a composite solid rocket propellant based on HTPB-binder

Thermal decomposition kinetics of solid rocket propellants based on hydroxyl-terminated polybutadiene-HTPB binder was studied by applying the Arrhenius and Flynn-Wall-Ozawa's methods. The thermal decomposition data of the propellant samples were analyzed by thermogravimetric analysis (TG/DTG) at different heating rates in the temperature range of 300-1200 K. TG curves showed that the thermal degradation occurred in three main stages regardless of the plasticizer (DOA) raw material, the partial HTPB/IPDI binder and the total ammonium perchlorate decompositions. The kinetic parameters E-a (activation energy) and A (pre-exponential factor) and the compensation parameter (S-p) were determined. The apparent activation energies obtained from different methods showed a very good agreement.

Synthesis, characterization and thermal studies on solid compounds of 2-chlorobenzylidenepyruvate of heavier trivalent lanthanides and yttrium(III)

Solid-state compounds of general formula LnL(3)center dot nH(2)O, where Ln represents heavier lanthanides and yttrium and L is 2-chlorobenzylidenepyruvate, have been synthesized. Chemical analysis, simultaneous thermogravimetry-differential analysis (TG-DTA), differential scanning calorimetry (DSC), X-ray powder diffractometry, elemental analysis and infrared spectroscopy have been employed to characterize and to study the thermal behaviour of these compounds in dynamic air atmosphere.On heating these compounds decompose in four (Gd, Tb, Ho to Lu, Y) or five (Eu, Dy) steps. They lose the hydration water in the first step and the thermal decomposition of the anhydrous compounds up to 1200 degrees C occurs with the formation of the respective oxide, Tb4O7 and Ln(2)O(3) (Ln=Eu, Gd, Dy to Lu and Y) as final residue. The dehydration enthalpies found for these compounds (Eu, to Lu and Y) were: 65.77, 55.63, 86.89, 121.65, 99.80, 109.59, 131.02, 119.78, 205.46 and 83.11 kJ mol(-1), respectively.

Resíduos de fentoato em tomate

The objective of the present research was to study the degradation and the persistence of phenthoate (Elsan 50 CE) residues in tomato fruits. The experiment was set in a tomato field located in Mombuca, State of São Paulo, Brazil, after 45 days from seedlings transplantation. Dosages of 600 (A), 800 (B), 1200 (C) and 1600 g a.i./ha (D) were sprayed at the beginning of the ripening period of fruits. Samples of 15 fruits each were collected 1, 4, 10, 20 and 40 days after products spraying. The utilized procedure consisted of extraction with acetone and purification by partition with dichloromethane. The purified extract was concentrated and injected into a gas chromatograph equipped with alkaly flame ionization detector (AFID). The limits of detection were of 0,01 ppm for this product. The recovery percentage from fortified samples varied from 60 to 81%. The degradation and the persistence half-lives were 1 to 2 and 3 to 6 days for phenthoate, respectively.