Physical Models of Wind Instruments : A Generalized Excitation Coupled with a Modular Tube Simulation Platform

To develop real-time simulations of wind instruments, digital waveguides filters can be used as an efficient representation of the air column. Many aerophones are shaped as horns which can be approximated using conical sections. Therefore the derivation of conical waveguide filters is of special interest. When these filters are used in combination with a generalized reed excitation, several classes of wind instruments can be simulated. In this paper we present the methods for transforming a continuous description of conical tube segments to a discrete filter representation. The coupling of the reed model with the conical waveguide and a simplified model of the termination at the open end are described in the same way. It turns out that the complete lossless conical waveguide requires only one type of filter.Furthermore, we developed a digital reed excitation model, which is purely based on numerical integration methods, i.e., without the use of a look-up table.

W-Band Planar Wide-Angle Scanning Antenna Architecture

This paper proposes a hybrid scanning antenna architecture for applications in mm-wave intelligent mobile sensing and communications. We experimentally demonstrate suitable W-band leaky-wave antenna prototypes in substrate integrated waveguide (SIW) technology. Three SIW antennas have been designed that within a 6.5 % fractional bandwidth provide beam scanning over three adjacent angular sectors. Prototypes have been fabricated and their performance has been experimentally evaluated. The measured radiation patterns have shown three frequency scanning beams covering angles from 11 to 56 degrees with beamwidth of 10?±?3 degrees within the 88-94 GHz frequency range.

The Source of 3 Minute Magnetoacoustic Oscillations in Coronal Fans

We use images of high spatial, spectral, and temporal resolution, obtained using both ground- and space-based instrumentation, to investigate the coupling between wave phenomena observed at numerous heights in the solar atmosphere. Analysis of 4170 Å continuum images reveals small-scale umbral intensity enhancements, with diameters ~0."6, lasting in excess of 30 minutes. Intensity oscillations of ˜3 minutes are observed to encompass these photospheric structures, with power at least three orders of magnitude higher than the surrounding umbra. Simultaneous chromospheric velocity and intensity time series reveal an 87?±8? out-of-phase behavior, implying the presence of standing modes created as a result of partial wave re?ection at the transition region boundary. We ?nd a maximum waveguide inclination angle of˜40? between photospheric and chromospheric heights, combined with a radial expansion factor of <76%. An average blueshifted Doppler velocity of ˜1.5 km s-1, in addition to a time lag between photospheric and chromospheric oscillatory phenomena, con?rms the presence of upwardly propagating slow-mode waves in the lower solar atmosphere. Propagating oscillations in EUV intensity are detected in simultaneous coronal fan structures, with a periodicity of 172±17 s and a propagation velocity of 45±7 km s-1. Numerical simulations reveal that the damping of the magnetoacoustic wave trains is dominated by thermal conduction. The coronal fans are seen to anchor into the photosphere in locations where large-amplitude umbral dot (UD) oscillations manifest. Derived kinetic temperature and emission measure time series display prominent outof-phase characteristics, and when combined with the previously established sub-sonic wave speeds, we conclude that the observed EUV waves are the coronal counterparts of the upwardly propagating magnetoacoustic slow modes detected in the lower solar atmosphere. Thus, for the ?rst time, we reveal how the propagation of 3 minute magnetoacoustic waves in solar coronal structures is a direct result of amplitude enhancements occurring in photospheric UDs.photospheric UDs.

Artificial surfaces of intertwined square spirals:A CPW model

Intertwining planar spirals arranged in doubly periodic arrays enables a substantially subwavelength response of the unit cell smaller than 1/40 of wavelength with large fractional bandwidths. These properties are important for application at low frequencies, conformal curved surfaces, or with compact radiators. It is shown that interleaving counter-wound spiral arms extended into adjacent unit cells dramatically increase the array equivalent capacitance while reducing the inductance. A coplanar waveguide (CPW) model has been developed to analytically estimate the equivalent capacitance and inductance of intertwined spiral array elements in terms of their geometrical parameters. The proposed CPW model is shown to provide an accurate prediction of the fundamental resonance frequency and can be instrumental in the design of the arrays for a specified frequency response. © 2012 IEEE.

Rotman Lens Used as a Demultiplexer/Multiplexer

Email
Print
Request Permissions











A new type of microwave demultiplexer is proposed which combines an arrayed waveguide grating (AWG) and a Rotman lens. The dispersion property of an AWG is employed to produce different phase slope responses for different frequencies, while the Rotman lens routes the frequency components onto different ports. To optimize isolation performance, the design constraints of both the AWG and the Rotman lens are re-examined and new design criteria elaborated. The optimized design is demonstrated of being capable of achieving 15 dB channel isolation over a 25% band range centered at 10 GHz. While a design based on a conventional Rotman lens yields isolation level of around 6 dB over a 9% band range centered at 10GHz.

Coherently Opening a High-Q Cavity

We propose a general framework to effectively `open' a high-Q resonator, that is, to release the quantum state initially prepared in it in the form of a traveling electromagnetic wave. This is achieved by employing a mediating mode that scatters coherently the radiation from the resonator into a one-dimensional continuum of modes such as a waveguide. The same mechanism may be used to `feed' a desired quantum field to an initially empty cavity. Switching between an `open' and `closed' resonator may then be obtained by controlling either the detuning of the scatterer or the amount of time it spends in the resonator. First, we introduce the model in its general form, identifying (i) the traveling mode that optimally retains the full quantum information of the resonator field and (ii) a suitable figure of merit that we study analytically in terms of the system parameters. Then, we discuss two feasible implementations based on ensembles of two-level atoms interacting with cavity fields. In addition, we discuss how to integrate traditional cavity QED in our proposal using three-level atoms.

Dipolar emission in trench metal-insulator-metal waveguides for short-scale plasmonic communications: numerical optimization

Here we consider the numerical optimization of active surface plasmon polariton (SPP) trench waveguides suited for integration with luminescent polymers for use as highly localized SPP source devices in short-scale communication integrated circuits. The numerical analysis of the SPP modes within trench waveguide systems provides detailed information on the mode field components, effective indices, propagation lengths and mode areas. Such trench waveguide systems offer extremely high confinement with propagation on length scales appropriate to local interconnects, along with high efficiency coupling of dipolar emitters to waveguided plasmonic modes which can be close to 80%. The large Purcell factor exhibited in these structures will further lead to faster modulation capabilities along with an increased quantum yield beneficial for the proposed plasmon-emitting diode, a plasmonic analog of the light-emitting diode. The confinement of studied guided modes is on the order of 50 nm and the delay over the shorter 5 μm length scales will be on the order of 0.1 ps for the slowest propagating modes of the system, and significantly less for the faster modes.

Development of a rapid multiplexed assay for the direct screening of antimicrobial residues in raw milk

Antimicrobial residues found to be present in milk can have both health and economic impacts. For these reasons, the widespread routine testing of milk is required. Due to delays with sample handling and test scheduling, laboratory-based tests are not always suited for making decisions about raw material intake and product release, especially when samples require shipping to a central testing facility. Therefore, rapid on-site screening tests that can produce results within a matter of minutes are required to facilitate rapid intake and product release processes. Such tests must be simple for use by non-technical staff. There is increasing momentum towards the development and implementation of multiplexing tests that can detect a range of important antimicrobial residues simultaneously. A simple in situ multiplexed planar waveguide device that can simultaneously detect chloramphenicol, streptomycin and desfuroylceftiofur in raw dairy milk, without sample preparation, has been developed. Samples are simply mixed with antibody prior to an aliquot being passed through the detection cartridge for 5 min before reading on a field-deployable portable instrument. Multiplexed calibration curves were produced in both buffer and raw milk. Buffer curves, for chloramphenicol, streptomycin and desfuroylceftiofur, showed linear ranges (inhibitory concentration (IC)₂₀–IC₈₀) of 0.1–0.9, 3–129 and 12–26 ng/ml, whilst linear range in milk was 0.13–0.74, 11–376 and 2–12 ng/ml, respectively, thus meeting European legislated concentration requirements for both chloramphenicol and streptomycin, in milk, without the need for any sample preparation. Desfuroylceftiofur-contaminated samples require only simple sample dilution to bring positive samples within the range of quantification. Assay repeatability and reproducibility were lower than 12 coefficient of variation (%CV), whilst blank raw milk samples (n = 9) showed repeatability ranging between 4.2 and 8.1 %CV when measured on all three calibration curves.

SIW slot antenna for E-band communications

The paper proposes novel substrate integrated waveguide (SIW) slot antenna for E-band communications. The antenna is designed at a two-layer low temperature co-fired ceramic (LTCC) substrate in 71-76 GHz frequency band. The proposed antenna demonstrates a gain better than 11.3 dBi and efficiency of 85% and can be used as a standalone antenna or as an element of a larger array.

On the numerical solution of the 2d wave equation with compact fdtd schemes

This paper discusses compact-stencil finite difference time domain (FDTD) schemes for approximating the 2D wave equation in the context of digital audio. Stability, accuracy, and efficiency are investigated and new ways of viewing and interpreting the results are discussed. It is shown that if a tight accuracy constraint is applied, implicit schemes outperform explicit schemes. The paper also discusses the relevance to digital waveguide mesh modelling, and highlights the optimally efficient explicit scheme.

Optical fiber sensing using quantum dots

Recent advances in the application of semiconductor nanocrystals, or quantum dots, as biochemical sensors are reviewed. Quantum dots have unique optical properties that make them promising alternatives to traditional dyes in many luminescence based bioanalytical techniques. An overview of the more relevant progresses in the application of quantum dots as biochemical probes is addressed. Special focus will be given to configurations where the sensing dots are incorporated in solid membranes and immobilized in optical fibers or planar waveguide platforms.

Photonic devices for optical and RF signal processing

O presente trabalho tem por objectivo o estudo de novos dispositivos fotónicos aplicados a sistemas de comunicações por fibra óptica e a sistemas de processamento de sinais RF. Os dispositivos apresentados baseiam-se em processamento de sinal linear e não linear. Dispositivos lineares ópticos tais como o interferómetro de Mach-Zehnder permitem adicionar sinais ópticos com pesos fixos ou sintonizáveis. Desta forma, este dispositivo pode ser usado respectivamente como um filtro óptico em amplitude com duas saídas complementares, ou, como um filtro óptico de resposta de fase sintonizável. O primeiro princípio de operação serve como base para um novo sistema fotónico de medição em tempo real da frequência de um sinal RF. O segundo princípio de operação é explorado num novo sistema fotónico de direccionamento do campo eléctrico radiado por um agregado de antenas, e também num novo compensador sintonizável de dispersão cromática. O processamento de sinal é não linear quando sinais ópticos são atrasados e posteriormente misturados entre si, em vez de serem linearmente adicionados. Este princípio de operação está por detrás da mistura de um sinal eléctrico com um sinal óptico, que por sua vez é a base de um novo sistema fotónico de medição em tempo real da frequência de um sinal RF. A mistura de sinais ópticos em meios não lineares permite uma operação eficiente numa grande largura espectral. Tal operação é usada para realizar conversão de comprimento de onda sintonizável. Um sinal óptico com multiplexagem no domínio temporal de elevada largura de banda é misturado com duas bombas ópticas não moduladas com base em processos não lineares paramétricos num guia de ondas de niobato de lítio com inversão periódica da polarização dos domínios ferroeléctricos. Noutro trabalho, uma bomba pulsada em que cada pulso tem um comprimento de onda sintonizável serve como base a um novo conversor de sinal óptico com multiplexagem no domínio temporal para um sinal óptico com multiplexagem no comprimento de onda. A bomba é misturada com o sinal óptico de entrada através de um processo não linear paramétrico numa fibra óptica com parâmetro não linear elevado. Todos os dispositivos fotónicos de processamento de sinal linear ou não linear propostos são experimentalmente validados. São também modelados teoricamente ou através de simulação, com a excepção dos que envolvem mistura de sinais ópticos. Uma análise qualitativa é suficiente nestes últimos dispositivos.

Quantum criptography in optical fibers

As comunicações quânticas aplicam as leis fundamentais da física quântica para codificar, transmitir, guardar e processar informação. A mais importante e bem-sucedida aplicação é a distribuição de chaves quânticas (QKD). Os sistemas de QKD são suportados por tecnologias capazes de processar fotões únicos. Nesta tese analisamos a geração, transmissão e deteção de fotões únicos e entrelaçados em fibras óticas. É proposta uma fonte de fotões única baseada no processo clássico de mistura de quatro ondas (FWM) em fibras óticas num regime de baixas potências. Implementamos essa fonte no laboratório, e desenvolvemos um modelo teórico capaz de descrever corretamente o processo de geração de fotões únicos. O modelo teórico considera o papel das nãolinearidades da fibra e os efeitos da polarização na geração de fotões através do processo de FWM. Analisamos a estatística da fonte de fotões baseada no processo clássico de FWM em fibras óticas. Derivamos um modelo teórico capaz de descrever a estatística dessa fonte de fotões. Mostramos que a estatística da fonte de fotões evolui de térmica num regime de baixas potências óticas, para Poissoniana num regime de potências óticas moderadas. Validamos experimentalmente o modelo teórico, através do uso de fotodetetores de avalanche, do método estimativo da máxima verossimilhança e do algoritmo de maximização de expectativa. Estudamos o processo espontâneo de FWM como uma fonte condicional de fotões únicos. Analisamos a estatística dessa fonte em termos da função condicional de coerência de segunda ordem, considerando o espalhamento de Raman na geração de pares de fotões, e a perda durante a propagação de fotões numa fibra ótica padrão. Identificamos regimes apropriados onde a fonte é quase ideal. Fontes de pares de fotões implementadas em fibras óticas fornecem uma solução prática ao problema de acoplamento que surge quando os pares de fotões são gerados fora da fibra. Exploramos a geração de pares de fotões através do processo espontâneo de FWM no interior de guias de onda com suceptibilidade elétrica de terceira ordem. Descrevemos a geração de pares de fotões em meios com elevado coeficiente de absorção, e identificamos regimes ótimos para o rácio contagens coincidentes/acidentais (CAR) e para a desigualdade de Clauser, Horne, Shimony, and Holt (CHSH), para o qual o compromisso entre perda do guia de onda e não-linearidades maximiza esses parâmetros.

Ultralow voltage resonant tunnelling diode electroabsorption modulator

Embedding a double barrier resonant tunnelling diode (RTD) in a unipolar InGaAlAs optical waveguide gives rise to a very low driving voltage electroabsorption modulator (EAM) at optical wavelengths around 1550 nm. The presence of the RTD within the waveguide core introduces high non- linearity and negative di erential resistance in the current±voltage (I±V) characteristic of the waveguide. This makes the electric ®eld distribution across the waveguide core strongly dependent on the bias voltage: when the current decreases from the peak to the valley, there is an increase of the electric ®eld across the depleted core. The electric ®eld enhancement in the core-depleted layer causes the Franz±Keldysh absorption band-edge to red shift, which is responsible for the electroabsorption e ect. High-frequency ac signals as low as 100mV can induce electric ®eld high-speed switching, producing substantial light modulation (up to 15 dB) at photon energies slightly lower than the waveguide core band-gap energy. The key di erence between this device and conventional p-i-n EAMs is that the tunnelling characteristics of the RTD are employed to switch the electric ®eld across the core-depleted region; the RTD- EAM has in essence an integrated electronic ampli®er and, therefore, requires considerably less switching power.

Electric field switching in a resonant tunneling diode electroabsorption modulator

The basic mechanism underlying electric field switching produced by a resonant tunneling diode (RTD) is analyzed and the theory compared with experimental results; agreement to within 12% is achieved. The electroabsorption modulator (EAM) device potential of this effect is explored in an optical waveguide configuration. It is shown that a RTD-EAM can provide significant absorption coefficient change, via the Franz– Keldysh effect, at appropriate optical communication wavelengths around 1550 nm and can achieve up to 28-dB optical modulation in a 200- m active length device. The advantage of the RTD-EAM over the conventional reverse-biased p–n junction EAM, is that the RTD-EAM has, in essence, an integrated electronic amplifier and, therefore, requires considerably less switching power.